Search Documents

By Sir Robert Hadfield

Table 1 gives the composition of the specimens listed by the author. The details of test procedure and the results of the tests on mechanical, magnetic and electrical properties and cor-rodibility of the alloys are published in full in a paper by the same author, "Alloys of Iron and Manganese Containing Low Carbon," presented before the Iron and Steel Institute (of Great Britain) and published in full in their Proceedings for 1927, to which reference should be made. After reporting these tests the author gives the following discussion of results:] The studies here reported do not indicate that any of the series has really valuable or useful qualities for industrial applications, though the demands of industry are so varied that it is unsafe to prophesy that no special use will be found for a given material. The non-magnetic property of manganese steel is due to the association of Fe and Mn, but carbon has also an effect, enabling non-magnetic qualities to be obtained with a much lower percentage of Mn than would otherwise be the case; for example, 16 per cent. Mn is necessary for alloys practically free from carbon, while with 1 per cent. C nonmagnetic alloys may be obtained with as little as 7 per cent. Mn. Carbon, however, is the prime cause of the development of magnetic qualities by heat treatment. (Sec section 8 of the paper referred to above.) These Fe-Mn alloys show a resistance up to 87 microhms per c. c., but. as there are other alloys which have a resistance as high as 130 microhms per C. c., this does not provide any new feature of value. The most marked feature of the series studied is the brittleness in the range 3 to 10 per cent., with a maximum of brittleness at 7 per cent. Material with this percentage, while possessing quite appreciable hard-

Jan 1, 1927

By Carl H. Unruh, D. L. Katz

Experimental data are presented for hydrate formation conditions for gas mixtures of carbon dioxide and methane. Equilibrium constants for carbon dioxide, defined as the mole fraction of carbon dioxide in the gas phase (dry basis) divided by the mole fraction of carhon dioxitle in the hydrate (dry basis)... were calculated usine the equilibrium constants for methane developed in an earlier paper. INTRODUCTION A series of papers have been written on gas hydrates, giving temperatures and pressures at which hydrates would form.2. 3, 4. 5, 6. 9. 12, 13, 15 Vapor-solid equilibrium constants have been developed for methane, ethane, propane and iso-butane' by which it is possible to compute for a specific gas mixture the temperature and pressure at which hydrates will form. Carbon dioxide is present in many natural gases in concentrations usually from 0.1 to 2.0 per cent. It also forms a gas hydrate with water and presumably enters the solid solution when present with a natural gas which is forming a hydrate. The equilibrium constant giving the ratio of the concentration of carbon dioxide in the gas phase to the concentration in the solid phase is required for including the effect of the carbon dioxide when computing the conditions for hydrate formation. Direct determination of the concentration of carbon dioxide in solid hydrate requires a difficult separation to be made. Therefore, this research resorted to the measurement of the temperature and pressure at which specific mixtures of methane and carbon diox- ide would form hydrates. From the equilibrium constants previously mentioned for methane, it is possible to compute the equilibrium constant for carbon dioxide, without measurement of the composition of the solid phase. Fig. 1 shows the conditions at which methane and carbon dioxide form hydrates. The methane curve FG extents to some high pressure while the carbon dioxide curve AB intersects the vapor-liquid water-liquid carbon dioxide

Jan 1, 1949

By Kenneth L. Adams

10.3-1. Introduction. Equipment replacement or maintenance is of major concern to every company today. It can be the difference between an efficient and profitable operation or an inefficient and struggling one. Mining equipment, as everyone knows, will not last forever. Some equipment becomes obsolete before it wears out while some may be doing its intended job, yet not economically. It is a major problem for management to make the decision as to whether a piece of equipment should be repaired or replaced. There are numerous approaches to this problem; using formulas, charts, and graphs. These would be very good if all conditions were stable. Since conditions and requirements are constantly changing, an accurate observation cannot be derived from a set formula. A formula does, however, serve as a reminder to include most of the items that should be considered when evaluating old and new equipment. In the field of mining there are several questions which enter into the reasoning that are difficult to put into an equation. Some of these are: 1. Will the present equipment produce the required output of the mine, or an increase if necessary? 2. Are reserves adequate to support the purchase of new equipment? 3. Can the old equipment be repaired to efficiently continue the mining operation? 4. What is the stability of future markets for the product? Depreciation rate, or the write-off life, is a factor that can directly effect decisions on replacement. If the initial life expectancy is too long and the price of equipment is not written off when discarded, then the original investment has not been recovered. If the write-off time is too short, then the equipment is written off before replacement is even considered. In this case, the depreciation accrual is usually used to finance some other phase of the operation. In view of the increasing prices, the amount of depreciation fund is generally too small for much incentive to replace an older unit

Jan 1, 1968

By Carl H. Unruh, D. L. Katz

Experimental data are presented for hydrate formation conditions for gas mixtures of carbon dioxide and methane. Equilibrium constants for carbon dioxide, defined as the mole fraction of carbon dioxide in the gas phase (dry basis) divided by the mole fraction of carhon dioxitle in the hydrate (dry basis)... were calculated usine the equilibrium constants for methane developed in an earlier paper. INTRODUCTION A series of papers have been written on gas hydrates, giving temperatures and pressures at which hydrates would form.2. 3, 4. 5, 6. 9. 12, 13, 15 Vapor-solid equilibrium constants have been developed for methane, ethane, propane and iso-butane' by which it is possible to compute for a specific gas mixture the temperature and pressure at which hydrates will form. Carbon dioxide is present in many natural gases in concentrations usually from 0.1 to 2.0 per cent. It also forms a gas hydrate with water and presumably enters the solid solution when present with a natural gas which is forming a hydrate. The equilibrium constant giving the ratio of the concentration of carbon dioxide in the gas phase to the concentration in the solid phase is required for including the effect of the carbon dioxide when computing the conditions for hydrate formation. Direct determination of the concentration of carbon dioxide in solid hydrate requires a difficult separation to be made. Therefore, this research resorted to the measurement of the temperature and pressure at which specific mixtures of methane and carbon diox- ide would form hydrates. From the equilibrium constants previously mentioned for methane, it is possible to compute the equilibrium constant for carbon dioxide, without measurement of the composition of the solid phase. Fig. 1 shows the conditions at which methane and carbon dioxide form hydrates. The methane curve FG extents to some high pressure while the carbon dioxide curve AB intersects the vapor-liquid water-liquid carbon dioxide

Jan 1, 1949

By Herbert Ives

THE incandescent gas mantle is of considerable interest from the standpoint of temperature measurement because it presents a series of apparent contradictions to the established laws of radiation on which are based some of our best methods of temperature determination. One of these contradictions is that the mantle of least brightness (of the commercial thoria-ceria group) is the one having the highest temperature; this, though explicable without any violation of radiation laws, was long a stumbling block to the understanding of the performance of the mantle. Another anomaly is that the energy radiated by the mantle decreases with the rise of temperature, thus apparently invalidating total radiation methods of pyrometry, based on the fourth-power law. The discussion of methods of measuring mantle temperature which follows, is largely taken from an extensive study of the physics of the Welsbach mantle. 1 The incandescent gas mantle consists of a skeleton of refractory oxide of very light weight and open structure, formed by the ignition of a cotton or silk "stocking" previously thoroughly impregnated with salts of certain rare earths. The mantle of commerce is a mixture of approximately 99 parts of thorium oxide with 1 part of cerium oxide. This mixture, discovered largely by accident, gives luminous radiation many times greater than that from either of the constituents taken alone. It is customary to speak of the thoria as the "base" and the ceria as the "colorant," and the commercial mantle represents one of a family in which an oxide of low emissive power is employed as a base, which will assume a high temperature, while a small amount of some other oxide of high visible emissive power is added, which will reduce the temperature of the mantle but little. This is, in general, the most efficient- way, from the standpoint of visible emission, to utilize a substance of high emissive power in the visible spectrum. But it is not necessary. that two substances should be employed to produce a radiator

Jan 9, 1919

By Sir Robert Hadfield

(New York Meeting, February, 1913.) THE Hadfield method of producing sound steel ingots has been the subject of a paper 1 read before the Iron and Steel Institute, so that it will be unnecessary to describe it fully here. The object of the method is to make possible the production of steel ingots in which the pipe is almost entirely obliterated, and it is applicable particularly to the production of sound ingots, from which good rails could be rolled. The method in brief consists in casting the ingots on cars, usually with the small end down. Each ingot mold is provided with a sand top, rammed up in the well-known manner. After the mold is filled to the desired height with steel, a layer of slag about 0.5 in. thick is placed upon it and the balance of the mold is then filled with charcoal. Then, through suitable piping, an air blast is directed in numerous jets upon the charcoal, which is burned thereby, the combustion supplying additional beat to the top of the ingot, which helps to keep the top fluid and to retard its solidification, while the lower parts are rapidly losing heat by its transfer to the mold. By-one plan the ingots are cast in molds placed upon bogies, movable trucks, or platforms, in the position A, Fig. 1. The ingots are cast vertically on bogies, say four or more ingots on each bogie, as may be found most convenient, and the upper surface of the steel is maintained in a molted condition during the transit of the ingots from the casting pit to the stripper. This is effected by a series of air pipes, for example, three in number, with jets or holes on the under surface of such pipes, placed preferably horizontally, arranged in such a manner as to cause jets of air to impinge on the upper surface of the ingots. These holes or jets are made throughout the entire length of the overhead pipes, the length of such pipes being

Jan 4, 1913

By Oswald J. Heinrich

The serious objections to the Leblanc soda process may be enumerated as follows: 1st. The total loss of sulphur employed, equal to about one-third of soda produced. Various processes have been proposed to regain this sulphur, but none have come into practical operation on a large scale. 2d. The great balk of waste products, equal to nearly twice the amount of soda, which forms a serious annoyance about the works. 3d. The complicated series of operations necessary. 4th. The large amount of labor and fuel required. 5th. The prodoction of noxious gases which necessitate extensive condensing arrangements. 6th. The large capital necessary for the . erection and maintenance of the plant, These objections have long been recognized, and many attempts have been made during the last thirty or forty years, to discover and introduce a cheaper and more direct method for the manufacture of this important staple. The reaction between bicarbonate of ammonia and common salt, whereby bicarbonate of soda, insoluble in a solution of chloride of ammonium, is precipitated, has been closely studied for the last twentyfour years, on account of its simplicity and the purity of the product it affords. This ammonia-soda process is now so far developed, that while it is not in position to entirely replace the Leblanc process, yet it can successfully compete with it where the conditions and localities are favorable. The advantages of the ammonia-soda process may be summed up as follows : 1st. It is independent of the essential agent in the Leblanc process, via., sulphuric acid, and hence can be established in those localities where salt is abundant, and yet where sulphuric acid could not be made, or where it could not be transported profitably. 2d. The ammonia-soda process being a " wet" process, the evaporation of salt brines to obtain the solid salt required in the Leblanc process, is rendered unnecessary. 3d. The direct conversion of chloride of sodium into bicarbonate of soda, which can readily be converted into the maketable monocar-

Jan 1, 1879

By Milo W. Krejci

(Butte Meeting, August, 1913.) THE plant and quarries of the Inland d Portland Cement Co.. are located- at Metaline Falls, Wash, about 128 miles north of Spokane, on the Fend Oreille river, and 10 miles, of the Canadian border. The plant is one of a chain of cement plants controlled by the Lehigh Portland Cement Co., of Allentown, Pa. Work on this plant was commenced in June, 1910, and was completed in April, 1911, but on account of some delays in the construction of the power plant, the works were not put into operation until August., 1911. Since then it has been in continuous operation and has furnished the Inland Empire with a high grade of cement. Fig. 1 is a, view and Fig. 2 is a plan of the works. Water Power Development.-The source of the water supply for the hydro-electric plant of the Inland Portland Cement Co. is Sullivan lake, a body of water approximately 5.5 miles long and 0.5 mile wide, situated in the Kanisku Forest Reserve. A wooden crib dam was installed so as to raise the elevation of the lake 25 f and the additional storage capacity was taken up by the diversion of Sullivan creek into the lake by means of a wooden flume, 0.25 mile long, 6 by 8 ft. in crosssection, and a ditch 1,200 ft. long. The water from the lake follows the natural water course to an intermediate storage reservoir, which was created by the construction of an earthen dam. This pond was used in connection with the saw mill which was installed at this point. Besides the earth dam, there was also built a crib, at the point shown in the sketch map, Fig. 3. This crib dam is 35 ft. high. From this point the excess water follows the natural -course of Sullivan creek to the Pend Oreille river.

Jan 7, 1913

By Earl Oliver

Dean Roscoe Pound, of Harvard Law School, in addressing the A.I.M.E. Petroleum Division on Feb. 22, 1934, said, "When you are able to work out a program that is mechanically feasible, that is economicaIly advisable, and which seems in your judgment, which is just as good as that of anyone, to be politically wise, you will not have very much trouble in the end in inducing the courts of today to find that it is legally sound." The purpose of this paper is to show: first, legal conditions necessary to promote conservation and stabilization; and second, to suggest operating procedure when those legal conditions are established. The proposal is mechanically feasible and economically advisable. A growing public understanding should make it politically wise. The disappointing progress in the development of conservation and stabilization can be attributed to the lack of two legal concepts as integral parts of oil and gas law; i.e., (1) a practical substitute for the capture rule, (2) collective ownership control for the individual oil and gas pool. When these two concepts are established on an equitable basis, conservation and stabilization procedure will become a comparatively simple process, more or less automatic in its adaptation and operation. Establishing these concepts is the function of the law-making agencies and might well be left to them for discussion except that the mechanical processes that give them form and substance must first be developed by the engineer. A Substitute for the Capture Rule Much has been written on these subjects, but the most concrete statement that has come to the attention of this writer is the following from an article by Charles G. Haglund in the Kentucky Law Journal of May, 1934: The Oxford1 case is not only authority for the proposition that it is competent for the legislature to modify the old property law of capture with respect to oil and gas but that it may also delegate such authority to a subordinate body.

Jan 1, 1935

By George A. Guess

The increasing demand for greater speed and more accuracy, in making daily assays of ores and products from mills treating material containing but very small quantities of lead and copper, has caused the older analytical methods to be supplanted by new ones devised to meet the needs of modern work. For " control" work in copper-analyses, I had, previous to the present equipment, introduced in my laboratory the ordinary electrolytic method, using hollow cylindrical electrodes; and with these I began a series of experiments in determining the lead-content of daily mill-samples and controls. The results, proving accurate and satisfactory, I then devised, with Mr. H. E. T. Haultain, a cheaper electrode than the ordinary jaCket-electrode, which costs from $15 to $20,—the expense of the older form making the installation of many units very costly. The form of cathode finally adopted as the most satisfactory, shown in Fig. 1, is cut from 0.001-in. platinum foil. It is 12.5 cm. long, and is divided into a blade 4 cm. wide and 6.25 cm. long, and a tongue 0.7 cm. aide and 6.25 long, the immersion area being 50 sq. cm. and weight 1.5 grams. The blade is first sand-blasted and then corrugated lengthwise, in order to impart the necessary rigidity. Strips of platinum foil 0.001 in. thick, 12.5 cm. long and 0.5 cm. aide, having a median corrugation, form the anodes. Three electrodes are used in each cell; one anode in the middle and one cathode on each side of the anode. These electrodes are connected to slotted aluminum terminals, in which they are held by contact pressure. The terminals are 5/16in. rods, projecting 2 in. horizontally in front of the wall of the cabinet; at the back the middle electrode (anode) is connected with one pole of the current, and the two outer ones (cathodes) with the other pole.

Jan 1, 1906

By Sydney H. Loram

TEIS paper, which is merely an arrangement of data collected during several hurried journeys, is offered to serve as a record, until such time as a better substitute be compiled. My observations were confined, as far as possible, over the entire distance, to the actual river valley; because near the Central Cordillera the country is so mountainous as to be im; passable in any direction but that of the dominant valleys. The river is not navigable anywhere, and for the first part of its course is a mountain torrent that runs down the bottom of narrow, almost vertical-sided valleys, through which the only road requires repeated fording, and often following up the bed of the stream ; but the rock-walls, standing clean and free from debris on either side, present the different formations with remarkable distinctness. A topographical map and a cross-seetion of the Rio Huasco is given in Fig. 1. The Rio Huasco practically rises from Laguna Grande, a lake about 17 km. from the Argentine boundary, and 3,135 m. above se-level, which is fed by direct snow-water, and by a few streams varying from a considerable volume, when supplied by the melting snow, in late spring, to little or nothing during the rest of the year. It is a somewhat pear-shaped body of water, about 1.5 miles in length and half a mile in average width, with a reported maximum depth of 45 meters. It was formed by the choking up of a narrow continuation of the same valley with blocks of an agglomerate mentioned later. The present level is some 5 m. below high-water mark (to which point, according to local accounts, it has not been filled for 35 years). In the intervening margin is a calcareous deposit about 4 m. thick, formed by the rapid evaporation of the water in the exceedingly dry air, and aided by the capillary action of an aquatic plant, growing in thick masses around the edge of the lake. These masses, dying and banking up, form

Jan 1, 1905

By Oswald J. Heinrich

THE serious objections to the Leblanc soda process may be enumerated as follows : 1st. The total loss of sulphur employed, equal to about one-third of soda produced. Various processes have been proposed to regain this sulphur, but none have come into practical operation on a large scale. 2d. The great bulk of waste products, equal to nearly twice the amount of soda, which forms a serious annoyance about the works. 3d. The complicated series of operations necessary. 4th. The large amount of labor and fuel required. 5th. The production of noxious gases which necessitate extensive condensing arrangements. 6th. The large capital necessary for the erection and maintenance of the plant. These objections have long been recognized, and many attempts have been made during the last thirty or forty years, to discover and introduce a cheaper and more direct method for the manufacture of this important staple. The reaction between bicarbonate of ammonia and common salt, whereby bicarbonate of soda, insoluble in a solution of chloride of ammonium, is precipitated, has been closely studied for the last twenty-four years, on account of its simplicity and the purity of the product it affords. This ammonia-soda process is now so far developed, that while it is not .in position to entirely replace the Leblanc process, yet it can successfully compete with it where the conditions and localities are favorable. The advantages of the ammonia-soda process may be summed up as follows : 1st. It is independent of the essential agent in the Leblanc process, viz., sulphuric acid, and hence can be established in those localities where salt is abundant, and yet where sulphuric acid could not be made, or where it could not be transported profitably. 2d. The ammonia-soda process being a " wet" process, the evaporation of salt brines to obtain the solid salt required in the Leblanc process, is rendered unnecessary. 3d. The direct conversion of chloride of sodium into bicarbonate of soda, which can readily be converted into the maketable monocar-

Jan 1, 1879

By J. J. Egan, A. B. Kinzel

Much work has been done recently in an attempt to analyze the physicochemical mechanism involved in the production of steel by the open-hearth process. This has resulted in reducing the process to a series of interrelated phenomena obeying the usual laws of mass action and diffusion. Of these, the reaction of the iron oxide and carbon in the molten steel is of most interest from a technical point of view as it constitutes the main action in the usual steelmaking processes. A. L. Feild' has formulated a basic differential equation expressing the open-hearth reactions and Herty has done considerable experimental work on the determination of a number of constants involved in the basic open-hearth reaction. In considering the application of the law of mass action to the reaction FeO + C + CO + Fe, the iron will be taken as constant, as is the case in the open hearth and the carbon monoxide pressure will be assumed constant at one atmosphere. From this xy = m at equilibrium, where x is the percentage weight of carbon, y percentage weight of iron oxide and m the weight-concentration equilibrium constant. While it is customary for physical chemists to express equilibrium constants in terms of molar concentrations, the constant is here expressed as the product of the percentage-weight concentrations for ease of comparison with the constants quoted by Herty and by Beild, and for more ready applicability to the open-hearth reactions. Herty and his associates have attempted to calculate the value of this constant from data on open-hearth heats. So many variables affect these results that an adequate calculation presents very great difficulties. A value of 4 X lop2 was first arrived at, but this was later changed to 1.6 X 10-2. Feild, in order-to illustrate the operation of the differential equation of the open hearth, has assumed a value considerably lower than Herty's, namely, 1.0 X 10-2, the largest value consistent with certain theoretical

Jan 1, 1929

Book Notices CATALYSIS IN INDUSTRIAL CHEMISTRY. By G. G. Henderson. Lond. and N. Y., Longmans, Green and Co., 1919. 202 pp., cloth, 9 X 6 in., $3.25. This, the latest volume of the series of Monographs on Industrial Chemistry which is being published under the editorship of Sir Edward Thorpe, is intended to present broadly, our present knowledge of the phenomenon of which it treats. The hook reviews the existing literature on catalysis, paying particular attention to the many applications now used in industry. COMMERCIAL OILS-VEGETABLE AND ANIMAL. With special reference to Oriental Oils. By I. F. Laucks. 1st edition. N. Y., John Wiley and Sons, Inc.;, Lond. Chapman and Hall, Ltd., 1919. 138 pp., cloth, 8 X 5 in., $1.25. Intended to give to men in the oil trade, who have not had technical training, the technical data and information required in every-day dealings, in concise form. The various commercial oils are listed, together with their sources, uses, and phys-ical and chemical characteristics. The values have been collected from the standard texts, supplemented, particularly in regard to oriental oils, by the results obtained in the author's laboratory. FIFTY YEARS OF IRON AND STEEL. By Joseph G. Butler, Jr. Cleveland, The Penton Press, 1919. 145 pp., por., 10 X 6 in., leather. (Gift of author.) This volume is one of a special edition, of 100 copies, of an address delivered before the American Iron and Steel Institute in 1917, in which the author gives his personal reminiscences of the development in iron and steel making, as observed during an active participation in the industry in eastern Ohio, which began in 1857. To this are added some brief data on the early history of iron and steel, and a chapter on the activities of the American iron manufactures during the great war. The volume is profusely illustrated with portraits of men of note in the industry.

Jan 12, 1919

By R. P. Heuer, Paul M. Tyler

THE literature on refractories, although fairly extensive, is so scattered through books and periodicals as to be difficult of access to the general reader and most of the individual papers serve merely to illuminate some particular phase of the industry. Two general treatises by American authors8.16 are available, also the somewhat older works by a well-known British authority, 12,13 but these make their appeal to the technically minded ceramic engineer. Another small group of publications deals with the use of refractories, mainly in the iron and steel industry.1, 3,5,6,11,15 Raw materials utilized by the refractories industry have been covered by sundry books and articles. For the relatively nontechnical reader and economist, however, there appears to be no single review that purports to describe the industry as a whole. Furnace linings and other products that are classed as "refractories" are designed primarily to withstand high temperatures but this important property is by no means the only requirement; a suitable refractory material must likewise withstand slagging (chemical' action), abrasion (physical wear), and spalling, as well as the various other stresses and physical phenomena induced by heat, of which softening or incipient melting is only one phase. Nevertheless, subject to these highly practical considerations, the definition of a refractory material is based upon temperature resistance. Broadly speaking, any material that shows obvious signs of fusion after being heated slowly to 1500°C (2732°F) cannot be classified as a refractory material. The characteristic properties and requirements of refractory materials are conveniently summarized in Fig 1, prepared on the American Refractories Institute Fellowship at Mellon Institute, Pittsburgh, Pennsylvania. Most of the factors of service and properties of refractories given in this chart are interdependent and are greatly affected in degree by the functions of temperature and time. The factors in the chart are believed to cover the commoner questions.

Jan 1, 1949

By M. Gensamer

ALTHOUGH a large number of X-ray photograms of cold-rolled steel have been published, two circumstances have led to the experimental work reported in this paper. The first is that no complete study, making use of the pole-figure method of Wever1, has been made of cold-rolled low-carbon steel. Wever has published pole figures of mild steel sub-jected to plane parallel deformation1,2 and undoubtedly he has applied the method to cold-rolled mild steel, but the authors have not found these data published. Kurdjumow and Sachs3 have applied the method to the study of rolling and recrystallization textures in electrolytic iron; their results will be referred to later. The reason for this dearth of papers using the pole-figure method is obvious; a greater number of photograms and more analytical work (although this work is quite simple and straight-forward) are required to construct a pole figure than most investigators have felt worth while, despite the fact that no other method of which the authors are aware will satisfactorily depict the orientations of the crystal-lites in a polycrystalline aggregate. The second circumstance that led to the work reported in this paper was the appearance of a paper by Wayne A. Sisson4 on the same subject. In his valuable study of the factors influencing the development of pre-ferred orientations in cold-rolled mild steel, Sisson made one observation that required confirmation; that is, that at some stage of the rolling proc-ess the type of preferred orientation changed from the type that gives a photogram characterized as a "six-point" X-ray pattern to that known as a "four-point" pattern. A similar observation had been made by Tam-mann and Heinzel5, who studied the orientations developed in the rolling of steel by the specular reflection of light from the etched surface of rolled samples. These workers also found that the type of preferred orientation

Jan 1, 1936

By Walter Kauenhowen

Germany's crude oil production during 1935 totaled 3,007,711 bbl., an increase of 36.6 per cent over the 2,202,214 bbl. produced in 1934. The Nienhagen-Haenigsen field furnished 77 per cent of the total 1935 production. Cumulative production figures for Germany's two most important oil fields, Wietze and Nienhagen, show that during the period from 1872 to the close of 1935 the Wietze field produced 13,325,536 bbl. and the Nienhagen field 9,340,870 bbl. Table 1 gives statistics of German production since 1928, arranged both by fields and by oil provinces. Fig. 1 demonstrates the production of the various German fields since 1890. New Fields Discovered During 1935 five new fields came into production. The first of these, the Moelme-Hoheneggelsen field near Hanover, was opened up in April. This region has been sporadically drilled for oil since 1882, but not until 1935 was production on a commercial scale obtained. The oil comes from Mesozoic sandstones on the flanks of a shallow salt plug. Also during April, oil was found in commercial quantities in the Rhine valley at Forst, near Bruchsal. Tertiary and Mesozoic sandstones cut by faults of the Rhine Graben form the reservoir structures in this area. In July a wildcat well drilled on the Fallstein structure, a broad Triassic anticline near Halberstadt, came in as a producer from Permian (Zechstein) dolomite. In September commercial oil mas found at Gifhorn, near Braunschweig, in Wealden sandstones associated with a shallow, geophysically discovered salt plug. During the same month production was obtained at Heide, in Holstein, from the Permian Rotlie-gendes formation, in a structural high on which oil seepages have been known for years. Drilling Activities Published information indicates that during 1935 drilling totaled 574,000 ft., as compared with 436,000 ft. in 1934; 233,000 ft. in 1933 and 151,000 ft. in 1932. The German Government is subsidizing wildcat

Jan 1, 1936

By Walter Kauenhowen

Germany's crude oil production during 1935 totaled 3,007,711 bbl., an increase of 36.6 per cent over the 2,202,214 bbl. produced in 1934. The Nienhagen-Haenigsen field furnished 77 per cent of the total 1935 production. Cumulative production figures for Germany's two most important oil fields, Wietze and Nienhagen, show that during the period from 1872 to the close of 1935 the Wietze field produced 13,325,536 bbl. and the Nienhagen field 9,340,870 bbl. Table 1 gives statistics of German production since 1928, arranged both by fields and by oil provinces. Fig. 1 demonstrates the production of the various German fields since 1890. New Fields Discovered During 1935 five new fields came into production. The first of these, the Moelme-Hoheneggelsen field near Hanover, was opened up in April. This region has been sporadically drilled for oil since 1882, but not until 1935 was production on a commercial scale obtained. The oil comes from Mesozoic sandstones on the flanks of a shallow salt plug. Also during April, oil was found in commercial quantities in the Rhine valley at Forst, near Bruchsal. Tertiary and Mesozoic sandstones cut by faults of the Rhine Graben form the reservoir structures in this area. In July a wildcat well drilled on the Fallstein structure, a broad Triassic anticline near Halberstadt, came in as a producer from Permian (Zechstein) dolomite. In September commercial oil mas found at Gifhorn, near Braunschweig, in Wealden sandstones associated with a shallow, geophysically discovered salt plug. During the same month production was obtained at Heide, in Holstein, from the Permian Rotlie-gendes formation, in a structural high on which oil seepages have been known for years. Drilling Activities Published information indicates that during 1935 drilling totaled 574,000 ft., as compared with 436,000 ft. in 1934; 233,000 ft. in 1933 and 151,000 ft. in 1932. The German Government is subsidizing wildcat

Jan 1, 1936

By John Griffen

THE distinguishing principle of the Tromp process is the use of a medium in the bath which is not stable, i.e., the solids will settle and the density of the medium increases with depth. A medium of uniform density can most easily be effected by agitation or by means which increase the viscosity of the medium. Either of these works against the sharpness of separation of coal from its impurities. The Tromp process grinds the medium solids to relative coarseness, allows them to settle downward in the bath without hindrance, and introduces horizontal currents of medium at intermediate levels between top and bottom of the bath. This prevents any accumulation of particles denser than the upper layer of the medium from which the clean coal is conveyed away or an accumulation of particles lighter than the bottom layer or medium whence the refuse is removed. In a relatively shallow bath making a two-product separation, the intermediate horizontal currents sweep these intermediate gravity materials away to be discharged with the refuse removed by the conveyor. Such a system provides a number of advantages. The gravity of separation can be changed simply by changing the density of the medium without changing particle size of medium solids or other conditions, as would be necessary with a system requiring uniform or stable density throughout the bath. Some installations in Europe separate at 1.40 sp gr on one shift, producing a superclean coal, and on the next shift reclean refuse from dry cleaning units and effect a separation at 1.80 sp gr. Medium solids may be much coarser in size consist, which reduces the viscosity of the medium and promotes its fluidity and in turn the sharpness of separation. Coarser medium solids with a more rapid settling rate are much more easily recoverable from the dilute medium rinsed from the products. The Tromp process is not limited to the use of medium solids having magnetic properties. Instal-

Jan 1, 1952

By James A. Barr

Ferrophosphorus, an alloy of phosphorus and iron or perhaps a physical mixture of definite compounds of iron and phosphorus, has become of increasing importance as the use of the basic open hearth has extended. Commercial ferrophosphorus is a porous, brittle metal of crystalline structure and often with a bluish metallic luster. A typical analysis is as follows: Per Cent. Phosphorus......................................... 18.0 to 22.0 Iron............................................... 80.0 76.0 Oxygen............................................ 0.2 Sulfur............................................. 0.3 Silicon............................................. 0.1 Carbon............................................ 0.1 Manganese......................................... 0.2 This alloy was first made in an electric furnace, as it was thought that the high heat of the electric arc together with the reductive effect of carbon was necessary. About 1898, J. J. Gray, Jr., was producing a high-phosphorus pig iron in his furnace at Rockdale, Tenn., by using high-phosphorus, local iron ores. As these high-phosphorus ores were difficult to obtain, he conceived the idea of increasing the phosphorus content of the pig iron by the addition of phosphate rock to the furnace burden. When the phosphorus content of the pig was kept low and only small amounts of phosphate rock were added to the burden, no particular troubles were encountered, but when he increased the amount of phosphate rock to produce an 18 per cent. alloy, his furnace troubles rapidly multiplied. After many failures and freeze-ups, he was partly successful in making short campaigns on 18 to 20 per cent. "ferro." At first, when the furnace got in bad shape on ferro, he would switch to a regular pig-iron burden until the furnace was brought around sufficiently to start on ferro again. About this time, Mr. Gray applied for and obtained his first patent. As he grew more skilled in the furnace operations, he was enabled to extend the furnace campaigns and produce ferrophosphorus continuously for the life of the furnace lining. These improvements were made the subject of another patent issued in 1916.

Jan 1, 1925