Search Documents

By C. A. Hartnagel

The production of petroleum in New York in 1940, totaling 4,999,000 bbl., was only slightly under the amount produced in each of the previous three years. The year 1940 started auspiciously with a posted price on Jan. I of $2.75 a barrel. Four price reductions, beginning in May, resulted in August in a low of $1.85 a barrel, after which two increases brought the year's closing price to $2.15 a barrel. The favorable crude price at the beginning of the year stimulated an increased drilling program, especially in the water-flooding districts. In the Allegany County region, which accounts for about two-thirds of the state's oil production, 886 wells, including water-intake wells, were drilled; 200 more than in the preceding Year. During the closing months of the Year there was a marked decline in the number of wells drilled. The unfavorable position in which the industry found itself before midsummer was due largely to the loss of export markets for its high-grade lubricants, constituting approximately 25 per cent of its business. As a result of this situation, runs to refineries were curtailed as much as 30 Per cent at the middle of the Year. Improvement in market conditions toward the end of the Year found the stocks of available crude at an almost record low. Deep DRILLING with the gradual exhaustion of some of the important natural and flood-oil-produc-ing areas of the Allegany and Bradford pools, overproduction will not be a serious problem in the future. The possibility of finding new territory or deeper producing sands has been further lessened by the drilling of additional deep wells for gas in and about the present oil fields. Many of these wells drilled to the Oriskany sand-stone were over 4000 ft. deep and have tested the entire thickness of the Devonian formation, the upper 2000 ft. of which contain all the important oil-producing strata in the state. Water-flooding It is thus evident that the problem of the New york oil producers is not one of find-ing new supplies but of obtaining as much 6 oil as possible from the old developed fields that during the 60 years of their life have 1 produced I 3o,ooo,ooo bbl. of oil. Although a few floods were in operation before I9I9, when the production of oil by flooding was 1 made legal, the output for that year amounted to only 85I,000 bbl. From 1919 I on there has been an almost constant increase, which during the past four years has averaged well above 5,000,000 bbl. annually. During the last 22 years, which constitutes the period of important flooding operations, 651337,000 bbl. of oil have been produced in the state. Careful estimates indicate that between one-third and one-half of the oil fields are being flooded or are already watered out. Some of the flooded and watered-out areas include territory with unusually thick sands, which were highly productive during the early history of the fields. From a recent study of operations in the New York oil fields, it is estimated that about 65,ooo,oo bbl. of oil

Jan 1, 1941

By A. H. Larson, R. J. McClincy

ALTHOUGH arsenic has a very high vapor pressure and vacuum distillation appears to be a likely method for its removal from lead, the published literature contains virtually no information concerning the vacuum removal of arsenic from lead. Caldwell, Spendlove, and St. Claire1 mention arsenic in their investigation of the removal of volatile metals from lead by vacuum distillation. They do not, however, give any data for arsenic removal or refer to any actual experimental work involving arsenic dissolved in lead. Moriyama, Kozuka, and Miura2 have determined the activity of arsenic in dilute As-Pb alloys in the temperature range from 450" to 600°C using a closed galvanic cell. They found that the activities of both arsenic and lead showed a positive deviation from ideality at 600°C. In view of the lack of experimental data regarding the vaporization of arsenic from As-Pb alloys, a limited vapor pressure study was made on liquid alloys containing from 0.5 to 3.3 wt pct As in lead at 703°C. The pressure of As4(v) above the alloys studied was determined from weight-loss data collected by means of the inert-gas saturation method. The experimental apparatus and procedure used were similar to that discussed by Alcock and Hooper9 with modifications as described by the authors., The technique involved was one of passing a known volume of inert gas over the alloy to be studied in a known amount of time and determining the loss in weight of the sample. Because of the low vapor pressure of lead at 703"C, the observed weight loss could be attributed solely to the vaporization of arsenic as the tetratomic molecule AS43 Measurements of the apparent vapor pressure were repeated at different inert-gas flow rates until from three to five values were obtained which were independent of inert-gas flow rate. This value of the apparent vapor pressure was taken to be the equilibrium vapor pressure of the alloy under consideration. The vapor pressures measured in this investigation have been converted to the activities of arsenic in As-Pb alloys, Table I, by use of the data compiled by Elliott and Gleiser5 for the vapor pressure of pure arsenic. The standard state for arsenic was chosen as the pure, hypothetical, supercooled liquid. The activity of arsenic was calculated from the fourth root of the ratio PAs,/PAS,. The low magnitude of the vapor pressures given in Table I explains the difficulty en- countered by earlier workers in successfully vacuum distilling arsenic from very dilute As-Pb alloys. The data shown in Fig. 1 indicate that the As-Pb system behaves ideally. The apparent outlier represented by the alloy containing 1.43 mol pct As is a result of the fact that the pressure of As, above the alloy was barely detectable by the experimental procedure used in this investigation. Because of this, the apparent vapor pressure determined for this alloy could be in considerable error. Moriyama, Kozuka, and ~iura' have reported that arsenic shows a positive deviation from ideality in dilute solution in lead. However, details of their results have not been made available. This research was made possible by a grant from the National Science Foundation (GK-196) for which the authors are very appreciative.

Jan 1, 1970

By Bernard Greifer, Walter Rose

The purpose of this note is to call attention to a source of difficulty which can be responsible for inaccurate estimates of wetting liquid pressure gradients in mixture flow experiments of the Hassler1 type. It has been our experience occasionally to observe what were indicated to be negative pressure gradients, and these were regarded as anomalous in the sense that physically they seemed to contradict the requirement that the flux be in the direction of the potential field. At first it was thought that our scheme of assembling barriers and core sample led to such asymmetry in the distribution of isobars that the manometric leads at each end of the core were responding to internal pressures (within the core sample) which could be either positive or negative with respect to each other, and which in fact might tend to reflect on different effective core lengths in an unpredictable fashion as the wetting liquid saturation was changed. However, no compelling evidence of this possibility has been established. In addition, we were cognizant of the requirements to be satisfied in selecting manometric instrumentation to minimize the delay in response of the manometer to the differential pressures being measured, and were thus assured that our observations of anomalous pressure gradients could not be explained by faulty instrumentation. What we suggest is that if a leak sink occurs in the fluid lines connecting the core to either side of the differential manometer, errors exceeding 100 per cent may result in the estimation of wetting liquid pressure gradient, even though the leak is of such small magnitude that its existence would tend to be obscured by evaporation effects. This is because in a system with leaks at the specified places, the manometer rec- ords at steady state the pressure drop across the manometer barrier elements in addition to the pressure drop across the core sample. This possibility will be illustrated below analytically and by numerical example for the special case where the leak occurs on the high presure side of the core, since we are especially desirous to explain the significance of our observations of the so-called negative pressure gradients. It will be indicated, however, that leak sinks on the low pressure side of the core can account for observations of anomalously high values of pressure gradient, and that multiple leaks on both sides of the core can provide for some compensation so that the errors in pressure estimation are reduced. However, the major point to be emphasized is the fact that the impractical-ity of detecting the small leak sinks which give rise to the difficulties makes it a complicated task for the experimenter in a particular case to know with certainty that his estimation of pressure gradient lies within the limits of error which can be tolerated. Fig. 1 shows the electrical analog of the flow system we have employed in our studies. The inflow and outflow barriers. Rbl and Rb2, the manometer barriers, Rm1, and Rm2, and the core sample, Rc— for a particular fluid saturation and distribution— are all designated as resistance elements; the flowmeter is designated by an ammeter, A; the pressure source is designated by E; and the manometric device is designated by the voltmeter, V. Included in the circuit are the variable resistances, Rx and Ry, which may be regarded as the leak sinks, and which, in general, can vary in magnitude from zero (i.e., a large hole or shunt in the system) to infinity (i.e., no

Jan 1, 1950

By H. R. Ogden, E. S. Bartlett, A. G. Imgram

Notched and unnotched tensile specimens of wrought and recrystallized, oxygmted and hydro-genated tantalum and columbium were tested over a range of temperatures selected to encompass the ductile-to-brittle transition. Increasing the oxygen content of tantalum and columbium increased their strength, and raised their ductility transition temperature, but did not cause a marked deterioration of notch properties below that of commercially pure material. The adverse effects of oxygen were more pronounced for recrystallized structures than for wrought material. The effects of hydrogen are complicated by strain aging or slow strain rate hydrogen embrittlement at -105°F. However, in general, hydrogen had only a minor effect an strength, but markedly increased the effective transition tem-terature and caused a deterioration of notch properties . BCC metals including the refractory metals in Groups Va and VIa (V, Cb, Ta and Cr, Mo, W) can be expected to undergo a ductile-to-brittle transition and exhibit brittle fractures at low temperatures.' Notch embrittlement is associated with this phenomenon, and can be a serious design problem. Table I compares the tensile transition behavior and notch sensitivity of commercially pure Group Va and VIa refractory metals. The Group VIa refractory metals have considerably higher transition temperatures, and become notch sensitive at higher temperatures, than do the Group Va refractory metals. In addition, the Group VIa refractory metals are sensitive to metallurgical structure. Recrystallized structures generally have higher transition temperatures than wrought material of the same composition. The relatively poor transition behavior of the recrystallized structures of these metals is generally attributed to the segregation of interstitial impurity atoms at grain boundaries. Pronounced sensitivity to structure is not evident with commercially pure Group Va refractory metals, however. Since these metals have higher solubilities for interstitial elements than do the Group VIa metals ,4 it can be expected that higher total interstitial concentrations are necessary to develop a comparable degree of grain boundary segregation and to produce a similar sensitivity of transition temperature to structure. Increasing only the concentration of interstitial atoms in solution would tend to increase the flow stress of a metal in relation to its cleavage fracture stress and thereby raise its transition temperature, but would not be expected to cause a marked sensitivity of transition temperature to structure. A research program has been conducted at the Battelle Memorial Institute to evaluate the effects of interstitial oxygen and hydrogen on the transition behavior and notch sensitivity of tantalum and columbium, and to evaluate the effects of structure on "contaminated" material. EXPERIMENTAL PROCEDURES Notched and unnotched tensile specimens of oxygenated and hydrogenated tantalum and columbium with both wrought and recrystallized structures were tested over a range of temperatures selected to encompass the ductile-to-brittle transition Oxygen levels selected for study in both tantalum and columbium were nominally 500 and 1000 ppm, whereas nominal hydrogen contents were 150 and 500 ppm in tantalum and 150 and 300 ppm in columbium. Oxygen and hydrogen additions were made directly to 6-in. lengths of 1/2-in.-diam electron beam melted wrought bar stock, in a Sieverts Apparatus. Subsequent high-temperature annealing was required for homogenization of the oxygenated material, but was not necessary in the case of hydrogenated stock. The oxygenated and hydrogenated bars were then swaged to 1/4-in.-diam rods. Tensile specimen blanks were cut from the 1/4-in.-diam rods and annealed to achieve stress-re-

Jan 1, 1963

By Dean Goodermote, Carla S. Stone

I Introduction Coal fuels China. Roughly 70 percent of all commercial energy demand is supplied by domestic coal production and with the recent Chinese opening to the West, the Chinese Coal Industry may figure prominently in the export market as well. Because of the importance of China's coal industry to the future of China and the Pacific Rim energy balance, this paper reviews the industry and offers some cautious projections for its outlook. II Energy's Position in the Current Political and Economic Climate Traditionally, Chinese society has been dominated by the policies of its most important government leaders. Deng Xiaoping, Vice Chairman of the Communist Party is the current leader of China. Deng and his proteges are pragmatists. Although China's government structure is based on Marxist/Leninist tradition, Deng and his followers are promoting experiments with market economics and expanded relationships with Western Countries, which have encouraged foreign investment in China. Energy companies represent just one type of industry that is interested in helping the Chinese to develop their abundant natural resources. Although China's leadership is committed to a program of economic modernization, that program currently is experiencing what the Chinese government terms "readjustment". Readjustment cuts back in imports due to deficient foreign exchange and deemphasizes heavy industry, while it encourages agricultural and consumer goods output and, most imporant, energy production. Increased Chinese coal and oil production is essential both to fuel industry and, equally important, to provide foreign exchange. If sufficient energy production is not forthcoming, then economic growth will be severely retarded. China's 1979 per capita GNP of $260 is only slightly better than the weighted average achieved by low income countries of $230. (1) Delays in growth could lead to social unrest, threatening the position of the current leadership. Since there is no institutionalized mechanism for leadership succession and policy continuation, it is reasonable to assume that leadership changes could result in energy policy changes. III Energy Consumption Energy production is important to China's future economic health as highlighted by the World Bank. If China's economy grows rapidly, 5 percent to 6 percent during this decade, the Bank noted, a significant energy shortfall could occur as early as 1985. This state of affairs contrasts sharply with China's current position as a net hydrocarbon exporter. (2) To assure a healthy economic future, China's leadership is attempting to reduce its rate of increase in energy demand through conservation as well as to boost energy output. A massive conservation promotion program has been underway since 1979 and there is much room for improvement. China's industrial sector is only about half as energy efficient as is U.S. industry. (3) During the last two decades, each percent of increase in GNP has been accompanied by a 1.8 percent of increase in energy consumption. (4) This compares rather poorly with the United States where a less than one-to-one relationship exists. IV Energy Supply The short term prospects for oil production are uncertain. Production increases were rapid in the 1960's and early 1970's, averaging 20 percent annually, but most of this increase came from one field, Daquing. Now that Daquing's production has peaked and the offshore potential has yet to be developed, petroleum production has maintained a plateau of 2.1 million b/d, at least temporarily, of which approximately 15 percent is exported. (5) Output

Jan 1, 1982

By B. H. Kear

All the possible ways of forming simple two-dislocation boundaries in multiple slip orientations are deduced. It is shown that the principal differences in work hardening behavior of crystals plastically deformed in these orientations can he accounted for in terms of the likelihood of formation of diffuse boundaries, or deformation bands, consisting of the products of dislocation reactions of the Lomer type. Also, it is pointed out that the break-up of boundaries under the applied stress is more likely to yield interstitial jogs than vacancy jogs, whereas glide dislocations cutting throuqh dislocations trapped in particularly stable boundam'es can acquire both types of jogs. USING Frank's' grain boundary formula, Ball and Hirsch2 determined the parameters of all the possible boundaries that can be built from two sets of glide dislocations in the fee structure. This paper deduces the geometrical possibilities for the formation of these two-dislocation boundaries in the different multiple slip orientations, and discusses the role of boundaries in work hardening and in jog formation. Formation of Two-Dislocation Boundaries in Mutiple Slip Orientations. The parameters of the possible two-dislocation boundaries for any crystal orientation can be deduced most conveniently using the boundary formulae due to Amelinckx,3 in conjunction with the stereographic projection shown in Fig. 1. Suppose that slip occurs in a-BC and ß-CA. According to Amelinckx, when the two systems of glide dislocations are parallel, the rotation axis, u, of the boundary is parallel to (a x ß) and the unit normal, u, defining the boundary plane is parallel to (a x ß) x (BC x CA). On the other hand, when the glide dislocations form a crossed grid, u is parallel to (BC x CA) and u is parallel to (a x CA) x (ß x BC). In Fig. 1, (a x ß) is the pole of the great circle passing through a and ß, so that u is parallel to DC, i.e., parallel to [110]. Furthermore, (a x ß) x (BC x CA) is the pole of the great circle passing through DC and 6, so that u is parallel to [110]. Hence, when all the glide dislocations are parallel, the boundary is pure tilt with parameters u = [110], v = [ 110]. Similarly, it may be shown that the corresponding crossed grid of dislocations is a mixed boundary with u = [111], u = [111]. Consider the case of a crystal compressed in the [001] orientation. In this orientation, according to Fig. 1, there are eight available slip systems. In what follows, the different types of two-dislocation boundaries that are possible in this orientation will be examined by taking different combinations of two slip systems out of the available eight, with a-BC always one of the systems. Case (i)—Slip Systems a-BC and d-CB. The formation of a tilt boundary in (101), which consists of a crossed grid of edge dislocations with vectors BC andCB, is illustrated in Fig. 2(a). As the figure shows, slip is required in the system a-BC in one part of the crystal and in d-CB in the other part, with both sets of dislocations entering the boundary from opposite sides. The rotation axis of the boundary lies in (101), depending on the relative densities of the two sets of edge dislocations in the boundary. Case (ii)-Slip Systems a-BC and ß-CA. The two possible boundaries are shown in Figs. 2(b) and (c); boundary (b) is tilt with u = [110], u = [110], and

Jan 1, 1962

By Hermann Schmalzried, Carl Wagner

UPON heating a metal oxide or sulfide in H2, first only oxygen or sulfur is removed from the surface. Thus the metal/nonmetal ratio in the oxide or sulfide increases and the thermodynamic activity of the metal increases accordingly. For the formation of metallic nuclei, a certain super saturation is necessary, i.e., the activity of the metal must become greater than unity. Once nuclei of the metal have been formed, the supersaturation is supposed to decrease. Even under steady-state conditions of a reduction process, however, the activity of the metal inside an oxide or sulfide phase must be greater than unity in order to have a driving force for the individual steps of the reduction process. As an example, consider the reduction of Ag2S with a high mobility of cations and electrons. As shown schematically in Fig. 1, the reduction process involves the following steps:' 1) sulfur removal along the entire Ag2S surface in form of H2S, 2) migration of Ag' ions and electrons from the Ag2S surface to nuclei of metallic silver, 3) transfer of Ag+ ions and electrons from the Ag2S phase to the metal. For a finite rate of step 3, the activity of silver in Ag2S next to the Ag2S-Ag interface must be greater than unity. Moreover, for a finite rate of step 2, the activity of silver at the gas-Ag2S interface must be still somewhat greater. Theoretical considerations lead to the tentative conclusion that at least under steady-state conditions the supersaturation will be rather low.' To test this conclusion, the average activity aAg of silver in a Ag2S tablet about 2 mm thick with a diameter of 5 mm was followed as a function of time by measuring the electromotive force E of the cell Pt I Ag | Agl I Ag2S I Pt where AgI is used as a solid electrolyte in which only Ag+ ions are mobile. The activity aAg is calculated as aAg=exp(-EF/RT) Since the diffusion coefficient for transport of silver in Ag2S is very high (- 3 . l0-2 sq cm per sec),3 the average activity aAg is representative for both the bulk and the surface of the Ag2S tablet. Experiments were conducted at about 400°C. The cell was surrounded by an aluminum block in order to secure a uniform temperature and to eliminate thermoelectric effects. With the help of a potentiometer, first a potential of 0.16 v was applied to the above cell in argon in order to obtain a well defined initial state with a Ag/S ratio close to 2.000.~ Then the cell was disconnected from the potentiometer and a gentle stream of H2 was passed along the Ag2S surface. In view of the removal of sulfur in form of H2S, the electromotive force E decreased within 20 to 30 min to zero corresponding to a Ag/S ratio of 2.003 and became negative, indicating a value of aAg> 1. A representative plot electromotive force E vs time is shown in Fig. 2. The minimum of the electromotive force characteristic of the onset of

Jan 1, 1963

By A. E. Dwight, A. F. Berndt

ThE published U-Ru equilibrium diagram indicates the existence of six intermetallic compounds in this system.' The structure of only two of the compounds, u2Ru2,3 and URU3,4 have been identified. This communication reports on the crystal structure and density of Uau3, which is formed by a peritectoid transformation at 1025° ± 5°C: U3Ru4 + U3Ru5 = U2Ru3. An alloy with the stoichiometric formula U2Ru3 was prepared by arc melting electrolytic uranium and ruthenium of 99.9 pct purity on a water-cooled copper hearth under an argon atmosphere. After homo-genization at 1000°C for 3 days, a metallographic examination revealed that the peritectoid transformation was complete and less than 5 pct of a second phase was present. A powdered sample, obtained by crushing the brittle compound, was annealed for 1 hr at 1000°C and air-cooled. Debye-Scherrer patterns were obtained with filtered CrKa, FeKa, CoKa, or CuKa radiation. The X-ray patterns of U2Ru3 weFe indexed as an fcc structure with a. = 12.895 0.00lA. The unit-cell constant and its standard deviation were calculated by a computer program described by Mueller, Heaton, and Miller.5 The density, measured by an immersion method, was 14.45 g cm-3. A calculated density of 14.48 g cm-3 was obtained on the assumption that twenty-four formula units (120 atoms) comprise a unit cell. The space group is either oh7 Fd3m, or the less symmetric, T4h, Fd3, since reflections indexed as hk0 with h + k + 4n are absent. All values of h2 + k2 + 12 permitted by both space groups are listed in Table I together with dc, do, and I. values. The calculated d spacings were obtained by the computer program of Mueller, Meyer, and simonsen.6 The observed d spacings above 0.77A were obtained from X-ray" patterns prepared with CuKa radiation, above 0.90A with CoKa radiaaion, above 0.98A with FeKa radiation, and above 1.16A with CrKa radiation. An attempt was made to identify the crystal structure of U2Ru3 by comparison with published data on other A2B3 compounds. A recent compilation7 of intermetallic compounds lists thirty-two structure types with the A2B3 stoichiometry. Only two of the structure types are fcc and they are Sb2O3(r), senarmontite, with 16 Sb2O3 per unit cell, and In2Te3 for which several structures have been proposed.8 However, the two cases cited do not have twenty-four formula units in the unit cell. We therefore, cannot identify UPRU3 with any of the other known A2B3 compounds. Ternary alloys were made in which 5 at. pct Os, Rh, or A1 were substituted for 5 pct of the Ru in U2Ru3. The osmium substitution increased the unit cell constant to 12.899 * .001A, which is to be expected since the atomic volume of osmium is slightly larger than

Jan 1, 1969

By R. C. Edwards, T. G. Kirkland, Will Mitchell

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By R. C. Edwards, T. G. Kirkland, Will Mitchell

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By C. A. Hartnagel

During- the past 10 years the annual production of petroleum in New York has averaged close to 5,000,000 bbl., the total for the period being 49,881,000 bbl. In 6 of the 10 years, the production was slightly in excess of the 5,000,000 mark. The 1944 production of 4,697,000 bbl. represents a 7 per cent decline from the previous year. Of the total 1944 output, the Allegany County district, which includes two small areas of Steuben County, contributcd 3,614,065 bbl., a decline of 5 per cent from 1943, and the contribution of Cattaraugus County, which represents the northern extension of the Bradford pool of Pennsylvania into New York was 1,082,935 bbl., a decline of more than 14 per cent. Since March 1942, the posted price of New York crude oil has remained at $3.00 per bbl. On lug. I, 1944, a Federal subsidy of 75¢ per bbl. was granted to oil producers, thus making the price actually $3.75 per bbl. Since all of the oil produced in New York comes under the designation "stripper well operations," it is entitled to the Federal subsidy. During the last few years there has been little change in the number of wells drilled annually. In the Allegany field, which accounts for three fourths of the oil produced in the state, 1240 wells, including water-intake wells, were drilled during 1944 as compared with 1223 in 1943. There was no marked increase in the number of wells drilled after granting the subsidy of 75¢ per bbl. of oil on Aug. I, the increase being but 14 wells during the last half of the year over the preceding six months. In flooding operations it is not to be expected that even a substantial increase in the price of crude oil will be reflected quickly in an increase of the number of wells drilled or in a marked increase in production of crude oil. In flooded areas, oil is obtained through a program extending over a number of years. This program involves the drilling of the water or input pressure wells, drilling of the oil wells, building up the oil flood to maximum production, and finally the watering out of the well when the amount of oil produced in proportion to the water becomes so small that pumping is no longer profitable. The various operations may extend over a period of 10 years or more, during which time the price of crude may have fluctuated greatly. Although the rate of production can be controlled to a limited extent, it is evident that a flood when once begun must be continued regardless of the price of crude. During the past seven years New York crude has had a price range from $1.68 per bbl. in 1938 to the present price of $3.75 per barrel The field pattern now in general use for wells in a flood project is the "five-spot." Under this arrangement, the lease is divided into squares with a water well at each corner and an oil well in the center. In the all-over pattern of the lease each oil well is acted upon by four water wells and each water well supplies part of the pressure to four oil wells. Spacing between the input water wells and the oil wells usually varies from zoo to 225 ft. or, on an acre basis, there is one oil well and one water well for each 2 1/2 acres. In recent years there has been a tendency to increase

Jan 1, 1945

By Charles C. Templeton

Any explanation of the nature of multiphase fluid flow through porous media must ultimately involve a knowledge of the mechanism of such flow through the individual pores of the medium. To provide quantitative information of the latter type, a study was made of gas-liquid and liquid-liquid displacements in single uniform Pyrex capillaries with diameters as small as 4 microns. Quantitative observation of air-liquid displacements with zero contact. angle indicates the adequacy of a model based on Poiseuille's Law and the independence of capillary pressure and interfacial velocity. Consequently, this work discounts previous claims that flow is abnormally retarded in very small capillaries. For the displacement of a very viscous oil by water in a capillary initially filled with water, flow is faster than predicted by the above model. This behavior is probably due to the existence of a thin annular film of water between the oil column and the capi1lary wall as postulated by Yuster. INTRODUCTION The need for experimental observation of the microscopic nature of multiphase fluid flow, to further the understanding of the results of macroscopic flow investigations, has been previously recognized. Chatenever and Calhoun1 in connection with the API Project 47B have extensively studied the flow of fluids through layers of glass or lucite spheres between glass or lucite plates. Lowman2 prepared an interesting film concerning flow in a single capillary, using an apparatus which made a moving interface appear stationary in the field of a microscope. The purpose of the present investigation was to deter- mine what contribution might be made to this field by comprehensive quantitative observation of gas-liquid and liquid-liquid displacements in single capillaries of uniform, very small diameter. The techniques used are similar to those of Lowman but incorporate improvements necessary for quantitative work. Quantitative observations must begin with fluids of simple chemical composition to provide a basis for analyzing the more complex behavior that may be expected with natural reservoir fluids. However, some qualitative observations on systems involving crude oils are presented. Experiments of this sort involve the observation of the velocity of the interface separating two fluids, and have been performed in horizontal or vertical capillaries by several investigators.3,4,5,6,7,8 The most general treatment of their mechanics, by Brittin,9 involves forces due to capillarity, viscous resistance, gravity, an "end-drag" effect, and the rate of change of momentum of the capillary contents. Since the range of pore diameters of interest in petroleum reservoirs is about 0.1 to 100 microns, it was desired to perform these experiments in the smallest capillaries possible, to ascertain whether capillary diameter had any effect on the existing theory based on data from larger capillaries.* It was also important to be able more systematically to vary the direction and rate of displacement than was done by previous investigators. Finally, to concentrate attention on viscous and capillary forces by eliminating gravity as a parameter, this study involves only horizontal capillaries. The work of Eley and Pepper' with a "large" (0.766-mm diameter) horizontal capillary is the previous investigation which is most similar to the present method of quantitative observation. Here capillaries with diameters as small as 4 microns will be studied.

Jan 1, 1955

By R. C. Edwards, Will Mitchell, T. G. Kirkland

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By R. C. Edwards, Will Mitchell, T. G. Kirkland

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By S. Leber

Pole figures and pole distributions were used for the quantitative detevinination of the preferred orientations in swaged tungsten rods and the effect of subsequent wire drawing on the texture. In the swaged rod, the preferred orientation could best be described as a pseudo (111-112) [110] cylindrical texture. A secondary component was assigned the indices (110) [001]. Further reduction by swaging retained these cylindrical textures. Wire drawing caused lattice rotations about the wire axis, converting the cylindrical texture into a normal fiber texture. The conversion was initiated and proceeded lnost rapidly in the center of the wire. The (110) /001] component was converted into a (110) fiber texture by wire drawing. The effective rotations were about axes contained in the lransverse plane. The preferred orientation associated with tungsten wire usually has been assumed to consist of a (110) fiber texture. This implies rotational randomness around the wire axis. Leber1 has shown that rotation about the wire axis may be restricted resulting in a preferred orientation designated as a cylindrical texture. Specific crystal planes tended to remain aligned parallel to the wire surface. This texture seemed to be the result of the swaging operation used in the intermediate stages of fabrication. Bhandary and cullity2 detected similar textures in swaged iron wires. Peck and Thomas3 suggested that the preferential alignment of crystal planes parallel to the wire surface was the result of tangential flow, characteristic of swaging. Wire drawing, following swaging, twisted the crystals about axes parallel to the wire axis, converting the cylindrical texture into a normal fiber texture.4 In this investigation, quantitative techniques were used to more accurately characterize the cylindrical texture and to study its conversion into a normal fiber texture. PROCEDURE The material investigated was lamp-quality tungsten. Three ingots were rod-rolled and swaged to 112 mils diameter, and were then drawn to 10-mil wire. Samples were obtained after each drawing pass. (110) and (200) pole figures were obtained from samples prepared as shown in Fig. 1. To form the sample shown in Fig. l(a), l-in. lengths of wire were glued side by side to form a l-in. square. The composite was ground and electropolished to form a diametral reference surface. For certain specific tests, samples were prepared as shown in Fig. l(b). This composite was made from 10-mil-thick strips prepared by grinding on parallel longitudinal planes. The polished reference surface in this case was, in essence, the wire surface. The two forms of samples [~igs. l(a) and l(b)] were related by a 90-deg rotation around the wire axis. Because of ease in preparation, most data was obtained from the diametral samples. The X-ray data were obtained using a Siemen's pole-figure goniometer. These data were not corrected for absorption or defocusing effects, since only the angular locations of the intensity maxima were of interest. Regions of the pole figure more than 80 deg from the center were not investigated. Partial monochromatization was achieved by the use of unfiltered copper radiation and a krypton-filled proportional counter. No evidence of spurious white radiation effects5 could be detected. Therefore, more elaborate X-ray techniques were not required. Intensity levels were chosen to show all pertinent details of the orientation distributions. The reference plane for the pole figures was the diametral section. The orthogonal reference directions, shown in Fig. 1, were the wire axis, the radial axis per-

Jan 1, 1965

By E. P. Miesch, P. B. Crawford

A study was made of the effect of permeable and impermeable lenses in a reservoir on the production capacity of a well. Both steady-state and unsteady-state data were obtained. An electrical resistivity model was used to obtain the steady-state data and thermal models. were constructed to obtain the unsteady-state data. The productivity of a well is affected very greatly only when the lenses are close to the well. The effect of circular lenses on the productivity ratio can be correlated with the distance from the center of the lens to the center of the well divided by the radius of the lens. When this dimensionless distance is equal to six or greater, the effect of the lenses on production capacity will be negligible. The pseudo steady-state productivity of a heterogeneous reservoir can be predicted using steady-state data. INTRODUCTION Many analytical solutions of reservoir behavior assume that reservoir rock is uniform and homogeneous. Although this assumption is used, all of the data from core analyses and well logging indicate that the reservoirs are heterogeneous. Very little work has been done on the performance of heterogeneous reservoirs. The work of Landrum,l et al. showed that transient phenomena in oil reservoirs could be studied with thermal models. Pickering and Cotman2 used thermal models to study flow in stratified reservoirs and investigated the effect of inhomo-geneities in oil reservoirs on transient flow performance. Loucks3 made a mathematical study of the pressure build-up in a system composed of two concentric regions of different permeability. Root, Silberberg and Pirson4 studied the effect of the growth of the flooded region on water influx predictions using a thermal model consisting of three concentric cylindrical regions of different thermal properties which simulated the aquifer, the flooded region and the unflooded portion of the original hydrocarbon region. Tomme, et a1.5 made a mathematical study of vertical fractures. The object of this investigation was to study the effect of highly permeable and impermeable lenses in the vicinity of the wellbore on the pressure depletion history of the well. Steady-state data were obtained for both conductive and nonconductive lenses that completely penetrated the formation. The lenses were symmetrically located at various distances from the wellbore. The unsteady-state data were obtained on seven thermal models. EXPERIMENTAL EQUIPMENT AND PROCEDURE STEADY-STATE DATA The steady-state data were obtained from an electrical resistivity model 30 in. in diameter and approximately 11/2 in. deep. The outside of the model was lined with a 30-in. diameter copper strip, which served as the outer boundary of the reservoir. The bottom was covered with a sheet of plexiglass so that it would be nonconductive. The model was filled with a slightly saline solution. The well size was varied from an 0.064-in. diameter copper wire to a 10-in. diameter copper cylinder. Readings were taken with an impedance bridge using AC current to prevent polarization at the contacts. Copper and wax lenses were used to represent infinitely conductive and nonconductive lenses, respectively. The resistance was first measured for each well diameter with no lenses in the reservoir. Then the conductive and nonconductive lenses were spaced symmetrically at various distances from the well and the resistance read from each lens location. The diameters of the conductive lenses were 3, 1.022 and 0.624 in., and those of the nonconductive lenses were 3, 2.25 and 1.563 in. The ratio of each resistance reading to the resistance reading with no lenses in the reservoir

Jan 1, 1965

By E. W. Parker

PROBABLY everyone is well aware that from April 1 to September 11, 1922, anthracite production was completely suspended; during those 163 days not one ton of coal was produced in the anthracite region. The production loss was about 30 million tons, and although production is now at its peak, there is no possible way by. which, within any short space of time, that deficiency can be made up. During that time the miners sacrificed in wages something over 100 million dollars. The anthracite companies paid out in cash, keeping their mines in condition to operate when mining should be resumed, something like 30 million dollars without taking in one cent of revenue. The tonnage of domestic sizes included in that lost output was about 21 million tons. The anthracite operators figured that between September 11, 1922, and March 31, 1923, they would possibly be able to produce about 60 per cent. of the tonnage that was mined the preceding year, that is, from April 1, 1921, to March 31, 1922. The problem then arose as to how that tonnage could be distributed equitably throughout the United States and Canada. We had in our records in Phila-delphia the distribution by communities, about 20,000 of them, to which anthracite had been shipped during the last five years, so that we were well posted as to what each community should be entitled to receive. We allotted to each of those 20,000 communities 60 per cent. of the tonnage that it had received during the preceding coal year, and we have endeavored to see that whatever tonnage we have been able to produce should be equitably distributed on that basis. It was a matter simply of voluntary cooperation by the anthra-cite operators who placed the distribution of their tonnage practically in the hands of the Pennsylvania Fuel Commission; the anthracite companies have almost without exception acceded to every request that we have made of them. When communities were reported entirely out of coal, a telegram or letter to the directors obligated to that community has resulted in some anthracite being shipped there, so that we have thus far kept the distribution on a fairly equitable basis. Prior to the suspension of mining operations, pre-liminary negotiations were carried on for the renewal of the wage scale, the operators thinking that it could be adjusted satisfactorily, and that the same method of procedure would be followed as during the 20 years succeeding the strike of 1902. At every termination of the wage agreement since that date, until last year, an agreement had been reached early in the season that mining operations should be continued, with the under-standing that any new agreement should be retroactive to April 1. At the meeting of the committees of anthra-cite operators and miners, on March 21, 1922, the opera-tors were presented with an ultimatum by the miners to the effect that unless an agreement were reached within ten days, mining operations would cease. That was protested against by the committee of operators as being unfair, not only to the operators and the public but to the men themselves. In spite of this protest the suspension occurred and, as you know, continued until September 11.

Jan 4, 1923

By J. Buchwald, R. W. Heckel

THE DeHoff method' of analysis of ellipsoids of constant shape provides a quantitative metallo-graphic technique whereby the actual size distribution of the ellipsoids may be determined from polished and etched random planar sections. This method provides a useful metallographic tool since it appears to be the only method available for determining the size distribution of nonequiaxed second-phase particles. This method, however, assumes that the type of particle being studied is known to be either oblate or prolate of a fixed minor to major axis ratio, q. This, in general, means that one assumes either oblate or prolate ellipsoids of a given q and checks the total volume and surface area of the second phase as determined from the particle size distribution to values of these quantities determined by other techniques. Suitable check methods may be point counting, lineal fraction, and areal fraction methods for obtaining the total volume and the Smith and Guttman2 method of intercepts for obtaining the total surface area. If the initial guess at particle shape and q were incorrect, i.c., the volume and surface information obtained from the particle size distribution data does not agree with those values obtained by other techniques, another assumption must be made and the particle size dist distribution must be recalculated. A current study in this laboratory has involved a large number of these calculations. To facilitate the handling of the calculations, the DeHoff method was programmed in the FORTRAN language for an IBM 1620 computer. The purpose of this note is to briefly describe this program. The complete program along with a list of variable names, a sample input, and a sample output may be obtained from the senior author. Basically, the program provides for the calculation of particle size distributions for a series of q values for both oblate and prolate ellipsoids for each set of input data. The total volume of second-phase particles per unit volume are calculated for each calculated particle size distribution. The output of the program is arranged to allow a rapid comparison of the calculated volume and surface values to data obtained by independent check measurements. A condensed flow chart of the program in the notation of DeHoff1 is given in Fig. 1 The calculation of the number of particles per unit volume in the jth size class, Ni, according to the DeHoff method' is: where k(q) is the shape-correction factor given by DeHoff as a function of q for both oblate and prolate ellipsoids, A is the size-class increment, k is the number of size classes, ni is the number of particles in the ith class on the planar measurement surface, and B(j,i) are the saltykov3 coefficients which correct for measurement surfaces which do not pass through the major and minor axes of the particles. The values of /3(j,i) are included as a two-dimensional array in the program. Particular values of k(q) are included in the program in increments of q of 0.05. The first calculation is carried out for q = 1 (spheres), the second for q = 0.95 oblate, the third for q = 0.95 prolate, and so forth. The number of q values chosen for the calculation is determined by a control card in the input for each set of data.

Jan 1, 1965

By N. A. Gokcen, M. N. Dastur

In metallurgical process industries a knowledge of true melting and casting temperatures is very essential for increasing the operating efficiency as well as improving the quality of the finished product. Optical pyrometers are widely used for the purpose because of their cheapness and ease of operation. It is an unfortunate fact, however, that this mode of measuring temperature entails a source of severe error inasmuch as with all non-black bodies, the temperature observed is always below the true temperature owing to deficient emissive power. Hence, the need for emissivity correction arises. In 1913 Bidwell1 obtained emissivity values of 0.36-0.48 for a temperature range of 1520-1800°C. He measured the true temperature of molten iron by sighting into a carbon cavity immersed in the iron under an atmosphere of hydrogen. In 1914 Burgess2 determined the emissivity of a smooth surface of liquid iron free from oxide to be 0.37 under an atmosphere of hydrogen. He claimed to have attained an accuracy of within 5°C at 1500°C with an optical pyrometer using monochromatic light. He reported that no difference appeared to exist between the emissivities of pure iron and of steels containing considerable percentages of carbon, nickel or manganese; nor was there any appreciable variation of emissivity with temperature from 1530 to 1571°C. Wensel and Roeser3 found an elnissivity value of 0.4 for temperatures above 1375°C for cast iron. The average emissivity value for carbon steels reported by Leiber,4 odd,5 Hase6 and Umino7 range from 0.4 to 0.45. Knowles and Sarjant8 made an extensive study of emissivity of molten iron and steel over a wide range of workshop and laboratory conditions. Observations of true temperature were made with immersion thermocouples, and correlated with apparent temperatures indicated by optical pyrorneter readings taken on the pouring stream as it passed over the lip of the crucible. The emissivity of Armco iron was shown to be of the order of 0.4, rising slightly with increasing temperature. But for plain carbon steels containing up to 1.0 pct carbon the emissivity was shown to fall slightly with increasing temperatures. The results of their investigation are in agreement with those of Guthmann.9 Naeser,10 Spencer," Todd5 and Hase6 in regard to the relation between emissivity and temperature for plain carbon steels. However, Goller12 has found a rise of emissivity with increasing temperature for the same steels. Results of several investigations are given in Fig 1. Measurement of True and Apparent Temperatures The necessity for an accurate optical temperature scale for liquid iron in studies of gas-metal equilibria led to this investigation. Experimental measurements were carried out in the induction furnace used by Dastur and Chipman13 in their studies of the reaction of hydrogen with oxygen in liquid iron. The furnace as modified for this work is shown in Fig 2. The atmosphere of the furnace was a mixture of purified argon with hydrogen containing a small controlled amount of water vapor. Gases were preheated by means of a platinum-10 pct rhodium resistance coil. The stream of hydrogen sweeping across the surface of niolten iron vir-

Jan 1, 1950

By V. Carlson, J. A. Rowe, E. O. Bennett

This report concerns the microbial flora found throughout the surface facilities of six water-injection systems in Texas and Oklahoma. Each system is described in detail and water quality data are presented when available. Pseudomonads and sulfate-reducers (Desulfovibrio) were the predominate organisms found in the systems. The genera Sphaerotilus, Bacillus, Achromobacter, Minococcus, Clostridium, Flavobacteriurn, and Sarcina were also isolated in significant numbers. Molds, iron bacteria, sulfur bacteria and soil bacteria were found less frequently in the systems. It is concluded that a complex microbiological flora exists in oilfield water-injection systems. A tendency for waters to deteriorate in passage through solid bed filters is also noted. INTRODUCTION The injection of water into a subsurface formation is often accompanied by numerous problems, the origin and nature of which are only partially understood. During the past few years, investigators have indicated that bacteria are involved in some of these problems even though very little specific information is available concerning this matter. It is surprising that investigators working on microbiological problems in water injection have never made a complete study of the flora of these systems. The logical course to pursue is that of identifying the microbial flora and then examining each organism individually and in combination with others to determine if they produce a particular problem. The objective of the present investigation is to identify the microbial flora in water-injection systems. In addition. the quality of the water in most of the systems was determined and some observations made on the extent to which passage through surface-handling facilities affects water quality. The information derived from this study can serve as a foundation for additional basic investigations. EXPERIMENTAL PROCEDURE The microbial flora of six water-injection systems were studied at 50 sampling points. These systems are experiencing problems which may be attributable to micro-organisms, and two were being treated with antimicrobial agents at the time of this study. The samples were obtained by inoculating 1.0 ml of the water onto the different media at the sampling point. The media used for primary isolation included nutrient agar, Strokes agar, M-10-E medium and semi-solid thioglycollate medium. The cultures were returned to the laboratory, incubated at 30°C until growth occured; then, pure cultures were obtained from individual colonies. The pure cultures were identified according to standardbacteriologica1 procedures. Those organisms not fitting identification criteria exactly, even though exhibiting close similarities to known species, are listed as unidentified organisms. Membrane filters were used to make water-quality tests at intervals before and after collection of the microbiological samples. The filter discs were 47 mm in diameter with a 0.45-micron particle-size retention, and the tests were done under closed conditions at 20) psi. Membrane flow rates are plotted as increasing filtrate volumes, and the total solids contents arcs given when available. An effort was made to sample at each place in a system where a change in environment occurred. In this manner, the effect of passage through filters, tanks, hay sections, etc., on the microbial flora and water quality could be observed. RESULTS SYSTEM A This waterflood system (Fig. 1) is about four years old and daily pumps approx&ately 110,000 bbl of oil-free sour water from a 3,700-ft deep reef. The