Search Documents

By Charles H. Hopkins, J. M. Lohr

A COMMERCIAL development requiring a suitable alloy or alloys for sealing into various grades of glass made it desirable to have a more exact knowledge' of the expansion characteristics of the nickel-iron alloys than appeared in the published literature. The expansion of the more common [ ] types of glass under consideration varies from 2.7 to 10.4 X 10-s per degree Centigrade, over the range 20° to 400° C. For reference, the thermal expansion curves of several types of glass used for sealing by the lamp and tube industries are given (Figs. 1 and 2). This paper covers a detailed investigation of the thermal expansion of a series of nickel-iron alloys in which the nickel content varies from 30 to 70 per cent. Particular stress is laid on the alloys that contain between 40 and 55 per cent Ni.

Jan 1, 1938

By A. T. Yu

Over the last 80 years the conveyor belt has advanced from the troughed rubber belt to those with standard steel cable cores and those which can navigate curves or climb steep inclines. Now the latest generation of belt conveyors can claim hitherto unheard of capacities of 20,000 tph and single flight lengths well exceeding 16,000 feet. The stranded steel cable core belt is principally responsible for the spectacular improvement in load carrying ability of belt conveyors. The allowable working tension of these belts ranges from 2,500 lb per in. of belt width for 1/4 in. diam cable to 4,000 lb per in, for 3/8 in. diam cable. These ratings far exceed the 240 lb per in. per ply for rayon or nylon construction, and 30 lb per in. per ply for a lowcost cotton fabric.

Jan 1, 1970

By C. Feng, C. Elbaum

AN investigation of the fracture plane of titanium, containing 0.5 wt pct to 1 wt pct 0, was recently carried out by fracturing large-grain specimens in a tensile jig at room and liquid air temperature. The experiments were carried out on strip specimens 3 to 5 mm wide, 2 mm thick and about 100 mm long. The specimens consisted of several grains, each occupying the entire cross section of the strip and extending over a length varying from 5 to 20 mm. These specimens were prepared by a method described elsewhere.' The identification of the fracture plane was possible in twelve of approximately thirty crystals investigated. In some cases severe local distortion took place near the fracture and prevented identification of the fracture plane. On, at least, three occasions the fracture propagated in a helicoidal

Jan 1, 1959

By Kenneth E. Skiff

INTRODUCTION United Nuclear Corporation and Homestake Mining Company are partners in a major uranium mining and milling venture near Grants, New Mexico. The partnership was formerly called Homestake-Sapin Partners and was recently renamed United Nuclear-Homestake Partners (UN-HP). The mill, originally built in 1958, had a capacity of 1,650 tons per day. With subsequent improvements and the addition of the adjacent Homestake - New Mexico Partners mill, the UN-HP mill is currently rated at about 3,500 tons per day. An alkaline type leach process is utilized by the mill. Milling consists of five basic steps: A. Ore handling and preparation B. Extraction C. Solid-liquid separation D. Precipitation and purification E. Product preparation MILLING Ore Handling and Preparation The primary source of ore for the UN-HP mill is from its four

Jan 1, 1983

Prof. Mathesius analyzes the running of Howland's furnace No. 19, according to the method described by him in Stahl and Eisen, 1916, Nos. 30 and, 31, and in his work "Die physikalischen und chemischen Grundlagen den Eisenhüttenwesens" (Spamer, Leipzig). By assuming 500 Cal. lost from the hearth by radiation and cooling water per kilogram of pig iron made, a throat-gas temperature of 600° C., and taking the ratio of C02/CO as 0.64, he finds that his diagram would show 0.68 kg. of carbon oxidized per kilogram of pig iron, while Howland gives 0.66 kg. He expresses himself as well satisfied with this test of the accuracy of his theory. Making the further assumption that the heat losses from the shaft are 1,000 Cal. per kilogram of pig iron (twice as

Jan 5, 1917

By Alden B. Greninger

The study of mosaic structure of crystals1 has been confined until recently to the field of theoretical physics. Crystallographers, in general, have neglected the subject, although X-ray crystallographers constantly make use of formulas for intensities of X-ray reflection as modified by mosaic structure. Work on mosaic structure has centered chiefly on the task of proving or disproving the secondary-structure theory of Zwicky,² and very little attention has been paid to the visible imperfections of crystals. A. Goetz has been responsible for most of the supposed experimental confirmations of Zwicky's theory.3 On the other hand, Smckal,4 and Orowan,5 among others, maintain that there is neither theoretical nor experimental evidence to substantiate Zwicky's secondary structure. Lately the subject has been intensively investigated by Buerger,6 one of whose recent papers led to a symposium on mosaic structures.'

Jan 1, 1935

By Alden B. Greninger

The study of mosaic structure of crystals1 has been confined until recently to the field of theoretical physics. Crystallographers, in general, have neglected the subject, although X-ray crystallographers constantly make use of formulas for intensities of X-ray reflection as modified by mosaic structure. Work on mosaic structure has centered chiefly on the task of proving or disproving the secondary-structure theory of Zwicky,² and very little attention has been paid to the visible imperfections of crystals. A. Goetz has been responsible for most of the supposed experimental confirmations of Zwicky's theory.3 On the other hand, Smckal,4 and Orowan,5 among others, maintain that there is neither theoretical nor experimental evidence to substantiate Zwicky's secondary structure. Lately the subject has been intensively investigated by Buerger,6 one of whose recent papers led to a symposium on mosaic structures.'

Jan 1, 1935

By E. J. Parkins, H. L. Shergold

The paper is divided into two parts. The first part describes an investigation of the effect of temperature on the conditioning and flotation of an ilmenite ore with a 1:l oleic acid-fuel oil mixture as collector. During conditioning the pulp underwent characteristic changes of flocculation, deflocculation and dispersion which were monitored by measuring the power consumption of the conditioner motor. Optimum flotation results were obtained at the end of the deflocculation period. High ilmenite recoveries were obtained at high temperatures and high concentrate grades at low temperatures. The second part of the paper describes a study of the effect of temperature on the adsorption of oleic acid at the ilmenite/water interface. At high adsorption densities it was chemical and exothermic. Contact angles showed that the hydrophobicity of the collector-coated minerals increased with an increase in temperature.

Jan 1, 1976

[based on o report by HUBERT E. RISSER] There is a tendency among laymen to relegate America's coal industry to Pennsylvania and West Virginia, completely overlooking-or unaware of- the vast reserves, both those developed and those untapped, situated in the 1.4 million square miles between the Appalachians and the Rockies. At the 1965 AIME Annual Meeting, Hubert E. Risser, Principal Mineral Economist of the Illinois State Geological Survey, presented an interesting picture of the wealth of mineral fuels occurring in that area. In his talk entitled "Trends in Mineral Fuels in the Central United States", Mr. Risser underscored the fact that "more than half of the nation's known reserves of each of the three major fuels-oil, gas and coal-lie within the Central area." The highlights of his speech, with emphasis on the coal situation, are excerpted below.

Jan 6, 1965

By E. C. Herkenhoff

THIS subject may be controversial. Personal preferences influence the final selection of cyclones, and side issues such as costs, floor areas, head room, and ease of replacing worn parts all enter the picture, but the following comments and data should apply to most cyclone selection problems. Broadly, the uses for cyclones in wet classification may be divided into three fields: 1) Open circuit operation, for two products, in which feed rate and sizing vary and the products vary. For example, feed may be divided into a sand product and a slime product. 2) Open circuit operation, for two products, in which feed varies, one product to have constant sizing. This calls for adjustment in either the apex or the vortex aperture. 3) Closed circuit operation, the finished product to have constant sizing. Most classification jobs fall in this category.

Jan 8, 1957

By Knut L. Sandvik, Aage Solbakken

it is an established fact that the collecting properties of xanthates and anionic collectors are dependent on the hydrocarbon chain length. This is ascribed to the greater adsorption densities caused by increasing the xanthate chain length. As batch flotation tests showed similar trends for amines, an investigation of the adsorbing properties of amines was undertaken. Because earlier investigations showed adsorption densities for dodecylamine salts on quartz varying as much as 20 times under apparently similar conditions,1-4 it was decided to make a survey of the changes in adsorption density due to the drying conditions of the quartz. EXPERIMENTAL PROCEDURE The quartz, handpicked in the pegmatite quarries of Iveland, Setesdal, had the following composition: SiO2 99.81, A12O3 0.01, Fe2O3 0.05 and loss by ig-

Jan 1, 1969

By A. Tobey Yu

Despite its inherent low Btu content, western coal's low sulfur content may provide a near-ideal answer to satisfy US goals for clean air and energy self-sufficiency. Vast reserves, amenable to low-cost strip mining, serve as a powerful economic basis for its viability as a primary and dependable source of energy for the coming decades. A major consideration, the solution of which may not be obvious, is the transportation cost. These deposits are remote from the utilities of the heavily populated eastern regions of the US (Fig. 1). A coal mine in Montana is likely to be more than 1500 miles from its utility market, while an eastern coal mine may be situated only 200 miles away. Thus, the question raised is: how can the haulage cost of western coal be substantially reduced to an acceptable level?

Jan 7, 1975

By William R. Rumbold

The Kinta valley, in the State of Perak, one of the largest of the Federated Malay States, is probably at the present time the richest alluvial tin-district in the world, Perak producing from 20,000 to 25,000 tons of tin annually, and the Kinta valley being the chief producer. The valley runs approximately north and south, and is 30 miles long by 12 wide. It is very flat, the mountain-ranges on either side rising abruptly from the plain, that on the east being the great Central range of the peninsula, and that on the west a subsidiary range marked " Kledang " on the map, Fig. 1. The valley is drained by the Kinta river, which rises in the eastern mountain range and flows south to join the Perak river, being joined by numerous streams from both mountain-ranges.

Jan 1, 1907

By S. Yukawa, M. J. Sinott

The low solubility of bismuth in copper and its segregation at copper grain boundaries with resulting embrittlement is well known.1-3 The heterogeneous diffusion of liquid bismuth into polycrystalline copper has also been studied.4 This work presents some further observations on these phenomena using high-resolution auto radiography to detect the presence of bismuth in copper polycrystalline and bicrystal specimens. The auto radiographs were made by the stripping film technique which produces an autoradiograph that is intact with specimen surface and can be examined simultaneously with the under-lying microstructure. The details of the technique have been described previously.3 In one series of experiments, high-purity copper was alloyed with 0.02 to 0.03 wt pct radioactive bismuth obtained from the Oak Ridge National Laboratory. Melting and casting was done under a

Jan 1, 1960

By Donald Markle

Anthracoal is a mixture of small particles of anthracite coal and a matrix of practically pure carbon, formed from the distillation of coal-tar pitch or other suitable bitumen. It is a hard, dense, homogeneous mass, with a silvery luster and in color varies from silvery to grayish black. When pushed from the oven, it develops only partly the fingerlike structure of coke; but, unlike coke, it has a tendency to remain in blocky masses. When struck with a hammer or passed through crushing rolls, it breaks with an irregular fracture, similar to anthracite, but with very little fines. Due to its density, anthracoal is harder, tougher, and stronger than coke. The results of a test made by the blast-furnace department, of the Bethlehem Steel Co., on two barrels of anthracoal are given in Table 1.

Jan 1, 1922

By W. F. Burns

(Butte Meeting, August, 1913.) ATTEMPTS were made in 1908, at the Great Falls Works, to produce ingots direct from the Butte precipitate by smelting- the material in a reverberatory refining furnace. The ingots produced in this manner averaged 99.4 per cent. of copper and 0.40 per cent. of arsenic and antimony. The copper content being considered too low, it was decided to cast the copper into anodes and to treat the anodes in the electrolytic plant. No.1 Furnace, in which the precipitate was treated, was a regular cathode refining furnace previously employed in making wire bar, cake, and ingot from electrolytic cathodes. The hearth of the furnace was 24 by 12 ft., having a capacity of 100,000 lb. of cathodes. The furnace was coal fired, and the copper was dipped by means of trolley ladles.

Jan 7, 1913

By Roscoe Bell

An economic appraisal of the western phosphate industrial potentials made between 1945 and 1948 revealed possibilities for a considerable expansion in the production of high analysis phosphate fertilizer. The most significant facts are: (1) a rapidly increasing and a much larger potential market which might be reached from the western deposits, (2) the existence of large undeveloped deposits of phosphate rock, (3) potential energy from sulphuric acid, coal, or hydroelectric power in the general vicinity of the deposits. The challenge to the mining and metallurgical engineering profession is in the economical development of phosphate mines and in improving processes for utilization of the western ores and the recovery of byproducts to make the expanded western industry satisfactorily compete with the industry in the East and South in meeting the fertilizer needs of the Midwest and Far West.

Jan 4, 1950

Ocean environmental factors are an intriguing new set of parameters to be dealt with in the prospecting and exploration phases of resource development for both the continental margins and the deep ocean. While information and data gathering programs for ocean minerals would parallel onshore procedures, their costs generally run higher. Commercial Prospecting-Identification of Mining Sites Two modes of prospecting can be identified-commercia1 prospecting (in which the ultimate objective is to define potential mining sites), and scientific prospecting, which is conducted with different objectives in mind. For ocean exploration, both types of prospecting are carried out prior to the obtaining of any exclusive rights to explore and exploit a specific deposit. Deepsea's John Flipse adds: "Any commercial prospecting program should by its very nature require the freedom to search wherever minerals might occur with maximum flexibility."

Jan 4, 1975

By M. D. Hassiaslis

THE nature of a collector-coated mineral surface has been the subject of some experimentation and much speculation. Various aspects of the problem have been isolated and studied; it is probable, however, that there exist aspects as yet unrecognized, which are needed for a complete description of the system. The recognized elements of the problem are: 1-The nature of the chemical units comprising the film and the nature of the forces holding these chemical units to the mineral surface; 2-The orientation of the chemical units at the surface; and 3-The disposition of the collector units at the mineral surface. This report touches upon all three aspects of the broad problem; it deals, however, with a new and heretofore unrecognized element-the mobility of the collector units in the two dimensions of the solid-liquid interface.

Jan 11, 1951

By G. Stuart Jenkins

CONDITIONS at the properties of the Consolidated Coal Co. had reached a point where improvements were almost impractical. The mines, sunk years ago, had shafts and entries so small as to preclude the use of large mine cars. A radical change was necessary in the type of mining and also in the type of mine to accommodate such haulage units. After due consideration, the company decided to enter the field of trackless mining, utilizing belt conveyors and chain-flight conveyors, the belt conveyors to take the long haul, and the chain-flight conveyors to be used for gathering. It was decided not to sink a shaft, but to drive a slope on an inclination of 17 1/2°, which the company believes to be about the limit on which coal can be carried on a belt without rolling back unduly.

Jan 1, 1939