Search Documents

Owing to the increased consumption of sulphuric acid; Australian manufacturers have, from time to time, been seeking for a satisfactory source of sulphur that would make them independent of foreign supplies.Some years ago a considerable amount of acid was obtained from the roasting of Spanish pyrites. This ore, in 1913 or thereabouts, cost 16s. per ton f.o.b. Huelva, and freight to the eastern seaboard of Australia was about 20s. per ton. As the ore contained 48% to 50% of available sulphur, it was costing roughly 9d. or 10d. per unit, and, in addition, the cinder, after roasting, was a product of considerable value to smelters, containing as it did a high percentage of iron suitable for fluxing, and appreciable values in silver and gold.

Jan 1, 1925

A model was developed of a CIL/CIP circuit for recovery of gold and silver. The model uses a simple two rate representation of the leaching kinetics. Parameters for the leaching kinetics may be simply obtained by sampling the feed to a circuit and the tailings from each tank and assaying the solids for both gold and silver to obtain the assay profiles of the solids down the tanks. The parameters in such a leaching model would be expected to be a function of the ore type, the grind, whether oxygen was used and the general chemical environment. These parameters are primary inputs to the model for any simulation. Standard power law relationships are used to express the practical equilibrium between the gold and silver cyanides adsorbed on the active carbon and the tenor of the solutions. The parameters for this may be derived from solution and carbon assays for the same set of samples. The model is constructed by writing a mass balance for gold and silver in and out of each tank in the train and for the circuit overall. Other inputs to a simulation are the feed rate of ore, per cent solids of the slurry in the tanks, gold and silver loadings of the input æbarrenÆ carbon and the rate of movement of carbon through the circuit counter-current to the slurry. With appropriate practical parameters the simulation is able to reproduce typical tank profiles.

Jan 1, 2004

It is shown that factors associated with conditions whIch are thermodynamically favourable for the formation of CuS04 in roasting lead to high copper recoveries on leaching. One of these factors is the ratio of the air to solids used for roasting. This can be varied widely without loss of temperature control in the sulphating roasting of many Australian copper concentrates.Thus, the prediction of the air to solids ratio corresponding to a maximum p(SO3) value, for a given concentrate and temperature, is of importance in fluidized bed roasting, since this could be associated with the formation of a maximum quantity of CuS04. Calculations are presented which predict this air to solids ratio, not only for a given concentrate composition, temperature, and pressure, but also for air which is enriched with sulphur dioxide or oxygen.

Jan 1, 1968

The following brief observations on the mineral composition of the Mt. Oxide copper ore are intended to supplement the geological description of that ore-body recently published by Blanchard (2).'" The Mt. Oxide copper mine is situated about 45 miles W.N.W. of Dobbyn, in the Cloncurry district of Queensland (Fig. 1). A representative suite of specimens from the mine was obtained through the kindness of Mr. P. B. Nye, Executive Officer of the Aerial, Geological and Geophysical Survey of Northern Australia, and Mr. Jack Hall, the tributor of the Mt. Oxide mine. The specimens, as shown in Fig. 2, were nearly all from the sulphide zone, between the l04-ft. level and the 300-ft. level. Several additional specimens, together with information which will be referred to later were kindly sent to me by Mr. Roland Blanchard.MINERAL COMPOSITION OF THE COPPER OREThe mineral composition of the ore is relatively simple. It consists essentially of chalcocite, with varying, but minor figures...

Jan 1, 1940

By G McMillan, P Mulvey

"Geochemical characterisation is done based upon the geology and metallurgical batch testing prior to commencement of the operation of the plant.  Tailings repository design is based upon geochemical assessment of the waste material, as well as the geomechanical issues associated with storing the waste. The resultant conceptual and detailed design is incorporated into the environmental impact statement (EIS), upon which mine approval is based. The entire environmental monitoring and harm mitigation program, which is usually a condition of the Mine Lease approval, is based upon the applicability of the original characterisation.Tacit to this process is that there is no change in the geochemistry of the tailings, i.e. no change in the implications for acid & metalliferous or saline/neutral mine drainage (AMD/SNMD) generation. But any changes in milling and processing can have a substantive impact on the geochemical behaviour of the tailings metallurgy, and potentially render an operation non-compliant within the conditions of the mine license.Environmental and statutory approval implications for continuous improvements of metallurgy need to be understood because unintended consequences could cost more than the benefits of the improvement, and in some cases cost more than all the profit made from the mine.  Examples uncovered during audit and consultant practice will be presented together with a process to ensure implications for adverse environmental harm and license conditions are fully considered.*This paper is only available for individual download. It is not included in the conference proceedings*CITATION:Mulvey, P, 2013. Continuous improvement - how changes in metallurgy can have a substantive impact on environmental impact and closure - lessons learnt from environmental auditing, presented to MetPlant 2013 Conference (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By W. J. LANGRON

This paper describes the results of VLF-EM test surveys, using the Ronka EM-16 equipment, over a selection of environments in Australia and Papua.Using comparisons with known geology, drilling information and other geophysical work it is shown that the maximum depth of penetration of the method is about 100 ft but is considerably less than this in most areas.The author believes the method could aid in geological mapping and provide a useful adjunct to aeromagnetic surveying in some areas.

Jan 1, 1972

The Cowarra gold mine is at latitude 36°O'S. and longitude 149°19'E. which is roughly 20 miles north-north-east of Cooma.The deposit was· originally worked towards the end of the last century, but the presence of sulphides associated with the gold in the primary zone caused cessation of work when that zone was reached.GEOLOGY AND MINERALIZATIONThe principal country rocks are sandstones and shales of Silurian and Ordovician age, both very strongly folded with structural pitches ranging from a few degrees to almost vertical. The mine proper is within Silurian rocks and the main orebody (there are several minor parallel bodies) is developed within a shear striking approximately north, dipping approximately 70° east, and ranging in width from 2 ft to 15 ft but averaging about 4 ft.This shear is impregnated with quartz and sulphides with which the gold is associated. The predominant sulphide is pyrite though pyrrhotite is commonly present in quantity.Arsenopyrite and bornite are present in smaller amounts.Stillwell (1936, 1937a, 1937b, 1938, 1941) has published five mineragraphic reports on the ore.The various levels have been mapped in detail (Figs. 1-3) and the No. 2 level plan (Fig. 1) shows the general relationship of shearing, as now indicated by mineralization, and faulting. There is no apparent connection between the fold structures and mineralization.Fig. 3 is a longitudinal projection showing the distribution of gold expressed as inch-ounces. The estimation of...

Jan 1, 1965

This paper describes a proposal to reopen the Sylvia gold mine for underground exploration and development for an initial production of 10 000 tpa. A combination of trackless mining equipment and railtrack would be utilised for development with ore extraction being carried out by undercut and fill methods. The use of the smallest LHD units for mucking, and rail track for the main haulage together with airleg drilling will form the basis for development and stoping. The proposal has been subjected to an environmental impact assessment report to evaluate the impacts of the proposal on the natural and social environment in the area.

Jan 1, 1987

By Poi G, Madgwick J. C, Davis P, Pannowitz D, Cho D, MacKay B, Chan S. M, Varga R. A, Chun U

Periodic dilute sulphuric acid treatment ofstill, batch-fed, molassesenriched, microaerobic, manganese-dioxide-Ieaching microbial cultures led to marked improvements over untreated cultures. Percentage Mn++ recoveries increased (7X), rate of Mn++ formation improved (3X) and yields of Mn++ per molasses use were more economical (5 X). The yield in terms of molasses used improved with decreasing sugar used (eg 1.17 g Mn++/gram molasses at 0.2 per cent molasses (w/v) feed and 24 per cent (w/v) pulp density MnO2 tailings). The most effective Mn++ leaching in terms ofpercentage recovery (97 per cent) and rate ofleaching (46 mg Mn++/day) was at 0.5 per cent molasses (w/v) and 14 per cent pulp density (w/v) MnO2 tailings.

Jan 1, 1986

This paper on the relation of Granite and Sedimentary Contacts to Victorian Mining will, it is hoped, be of interest to members of the Institute.The broad fact that gold often occurs' at or near the junction of granite with sedimentary silurian or metamorphic rocks has been noted by some Victorian geologists, miners, and prospectors; but the fuq practical value -of the fact does not seem to have been fully realised by prospectors. Glancing at the Geological" Map of Victoria, one can see that many of our goldfields 'are situated at or near the junction of granite with Palceozoic sedimentary formations, and that some of our alluvial fields are on granite. Many prospectors are possessed of this knowledge but when prospecting a contact locality, they would be just as likely to confine their search for auriferous matrices to spots a quarter of a mile on the sedimentary side, as on the actual contact line of two formations.

Platinum-group minerals (PGM) are recorded from a number of localities along theWaiau River, western Southland, and the south coast of the South Island, New Zealand. At each locality, small amounts of PGMs were recovered as by-products of historical gold mining operations. During the period 1890-1950 an estimated 1000-2000 oz. of æplatinumÆ were recovered from the region, the only area within New Zealand where PGM have been commercially exploited. The PGM suite of southern New Zealand consists of Pt-Fe alloys, IPGE (iridium subgroup, platinum-group elements) alloys, sperrylite (PtAs2), cooperite (PtS) and braggite ((Pt,Pd)S). The composition of Pt-Fe alloy exhibits considerable variation and two compositional populations are recognised. Some Pt-Fe alloy grains are chemically zoned. Iridium is the most abundant IPGE alloy phase and often contains considerable Pt, in contrast to osmium and ruthenium alloys. Cooperite and braggite grains are characterised by extremely low concentrations of Ni.   Exsolution of osmium and iridium from Pt-Fe alloy and Pt-Fe alloy from iridium is observed Several PGM host mineral inclusions which vary from single to poly-phase, display rounded to equant outlines and range in diameter from greater than 100 ¦m to less than 5 ¦m. Olivine and Ni-sulphide inclusions are only present within IPGE alloys. Pt-Fe alloy, cooperite, braggite and sperrylite host Cu-Fe sulphides, a wide variety of PGM, clinopyroxene, amphibole, magnetite and plagioclase within inclusions. Sperrylite also hosts Pd bismuthiotellurides, gold and several potassium-rich silicate phases. Similarities in inclusion phases and mineral chemistry from several localities suggest that the PGM are derived from a single (as yet unidentified), probably calc-alkaline magmatic source. This source is situated somewhere along the margins of the western Southland sedimentary basin where PGM liberated by erosion are transported down the Waiau River and dispersed eastwards along the coast by strong longshore currents.

Jan 1, 1995

The disasters between 1920 and 1979 in coal mines in Queensland and New South Wales due to underground fire, gas or coal dust explosion or to gas or coal outbursts, have been assessed. The evidence relating to disasters caused by gas explosion points strongly to divergence from safe mining practice as the main cause. There is a need for greater training and education of personnel, closer analysis of gas reports, better monitoring and testing procedures, improved ventilation standards and a policy where safe working practice is actively encouraged. Conditions in the New South Wales occurrences of gas explosion were similar to those at Collinsville, Queensland in that dykes, igneous sills, burnt out coal and faulting were common to all. Information on outbursts indicates that contributing factors were intrusions, depth of cover, fault zones and other geological disturbances, methods of work, pressure and type of gas.

Jan 1, 1982

The banded iron formations "jasper bars," jaspilites, banded hematite quartzites or banded ironstones, etc., as they have. variously been termed in Western Australia, constitute one of the most striking features of the Pre-Cambrian in this State. They occur in at least two distinct divisions of the Pre-Cambrian, viz., in horizons interbedded with quartzites, shales and thin bedded dolomite in the N~llagine (Proterozoic) Series; and amongst the Older Pre-Cambrian rocks, associated with the metamorphosed sediments of the Jimperding-Chittering Series, the Yilgarn Whitestone Series and the Mosquito Creek Series, and interbedded with metamorphosed basic lavas, tuffs and sediments of the Older prenstone or Kalgoorlie Series.In the Hamersley Ranges in the north-west of Western Australia banded ferroginous cherts are well developed amongst the horizontal sediments of Nullagine Age. These iron formations have recently sprung into prominence as they have been found to form the host rocks for important deposits of· blue asbestos. They are closely comparable with the unique crocidolite-bearing banded ironstones of the Cape Province, South Africa, and have been described elsewhere in some detail by the writer. (1) t .The banded iron formations with which it is intended to deal principally in the following pages, form most abundantly in the Central and Eastern Goldfields of Western Australia where they form portions of the Older Greenstone or Kalgoorlie Series of auriferous rocks. In these regions their chemical inertness and physical hardness provide considerable resistance to the agents of erosion and consequently they frequently stand out in strong topographic relief in otherwise monotonously flat or gently rolling country. These banded-iron formations have proved of considerable direct economic importance in the goldfields and in other portions of the State because of thei!! associations with 'gold, iron -and to' a lesser extent, manganese; whilst indirectly because of their peculiar nature, form and topographic prominence, etc, they have been of tremendous assistance to the field geologist both in the practical application of methods of geological mapping and in the' elucidation of geological structures. Finally, they have recently acquired a new importance in the specialised search for ore-bearing lodes or for structural information over areas of soil-covered country, as their form and composition make them ideal subjects for the use of either electrical or m!1-gnetic methods of geophysical prospecting.

Jan 1, 1941

By P M. Hancock, Associates

Lacustrine sediments, hydrothermal explosion breccias and spring precipitates deposited 5200 - 1800 years BP as a result of geothermal activity at Lake Rotokaua, contain New Zealand's largest known sulphur reserves. Current drill indicated reserves are 2 600 000 tonnes of elemental sulphur, assuming a ten per cent (dry basis) cut-off, contained in some 17 000 000 tonnes of ore with an average grade of 214.0 per cent (dry basis) sulphur. Additional inferred ore containing 500 000 - 900 000 tonnes of sulphur has yet to be prospected by drilling. Geological factors will be important in exploitation of the deposit, particularly the extent and disposition of the orebody, sulphur grades and distribution, physical characteristics of the ore, permeability and stability of the overburden and the nature and extent of geothermal activity in the area. Trials to date indicate that Frasch mining and possibly opencutting are unlikely to be successful mining methods. Further mining feasibility studies will be required to ascertain the most likely mining system for the deposit.

Jan 1, 1984

NATURE OF ORETHE Edna May ore consists mainly of clean quartz of a moderately hard and tough nature. The gold content is "free" and fairly coarse, so that a large percentage is recovered by amalgamation. The ore is practically free from metallic minerals.GENERAL OUTLINE OF PLANT AND TREATMENTThe ore, received from underground in trucks, is broken by a jaw breaker, then stamp-milled, follow~d by partial filie-grinding in pans. Mercury is used both in the mill boxes and pans. The pulp, on leaving the pans, passes over amalgamating tables and is then elevated by tailings pulp to cone classifiers and separated into a sand and slime product, each product receiving a separate cyanide treatment-sand by leaching in vats and slime by agitation and decantation in a "Trent" plant. Gold solutions from both sand and slime are precipitated together by zinc shavings in the usual type of precipitation boxes. Accumulated slime is trucked from the dam to a vortex mixer and from this point receives with the cement slime the same treatment.ORE BREAKING AND TRANSPORTThe ore is trucked from the brace of the shaft along an overhead line to the breaker station. Hence it is, by means of a "kick-up" dumped upon a grizzly, set with 2-in. spaces, the oversize being broken by a 15 x '9 Fraser and Chalmer jaw...

Jan 1, 1919

The effect of conditioning energy input on the metallurgical results of an emulsion flotation process has beenattributed by previous authors to a detergency process.This paper shows that such a process does not explain the data and that an attrition mechanism is more appropriate.

Jan 1, 1970

(Published by courtesy of the Great Boulder Pty. Gold Mines, Limited)1. INTRODUCTIONThe faults described in the following paper are of a somewhat unusual character, and have presented a serious problem both in the development and mining of many ore-bodies on the Eastern side of the Boulder Belt. They are mentioned only briefly in the literature of the field, but were observed by, both Stillwell (1)t and Gustafson (2), and have been studied by other geologists and operators in various parts of the "Belt." Their effect on the lodes of Hamilton Section, Great Boulder Mine, was described by King (3) in 1937, and, during recent years, they have been encountered in most of the Great Boulder workings extending east of the Boulder Dyke.Although this paper is based mainly on a study of faulting and development problems on the Great Boulder mine, the general conclusions reached may be applicable to the solution of similar faulting problems in other mines throughout the field.In order to arrive at a clear understanding of the somewhat complicated relationships which the east-dipping faults bear to the lode systems it will be necessary to give a brief outline of the salient geological and structural features of the "Belt" before proceeding to describe the faults themselves.2. GENERAL GEOLOGYThe most recent descriptions of the geology of Kalgoorlie are those by Stillwell (1) and Gustafson (2) and the reader is referred to these as representing the basis of current knowledge of the geology of the field.The Boulder Belt is comprised of a central core of altered quartz dolerite which is flanked on either side by fine grained greenstones and lavas, usually referred to as the calc schists. Down the centre of the quartz dolerite mass there is an infolded bed of slate (2, p. 105) which has been intruded in lit par lit fashion by albite porphyry; the composite body of slate and porphyry so formed is known as the "Boulder Dyke." Numerous smaller porphyry dykes intrude both the quartz dolerite and the calc schist; these vary in composition and range from chloritised hornblende porphyrites to albite porphyries.The whole of the rock assemblage has been subjected tG a considerable amount of folding, faulting, shearing and fracturing, the greater part of which took place before the formation of the lodes.

Jan 1, 1941

THOUGH the literature on the chamber process is considerable, it mostly refers to European conditions. Owing to the demand for acid for flotation and leaching at the mine, it may be necessary to work the process under other conditions. Consequently, some results obtained during the chlorination days at Mount Morgan, within the Tropic of Capricorn, may be useful for reference when working in a similar climate. Though the chambers must be protected against tropical storms, thorough ventilation should be provided, with plenty of space between the chambers, which are almost invariably crowded together. Not only does the space assist in the cooling of the chambers, but it is very desirable during repairs, when lead andtimber have to be hoisted up. The connecting flues between the chambers, which are fairly efficient mixers and condensers, should be round, supported from above, and with the least possible timber about them. Their position and arrangement deserve careful attention. Lattice work will be sufficient protection for the sides of the chambers, and the roof should be high and well ventilated. The Mount Morgan plant, crowded and not well situated, consisted of seven chambers (four over 50 ft. in length), one Glover tower 7 ft. 2 in sq. x 20 ft. high, one Gay Lussac 9 ft. sq. x 30 ft. higb, also one 5 ft. diam. x 25 ft. high. There was one pipe column 4: ft. sq. x 14 ft. 6 in. high. The chambers were run as one unit, and were much lower than those usually constructed in Europe-less than 15 ft. high. Provided that suitable timber can be obtained, 20 ft. is quite low enough. It should be quite satisfactory to use round poles for the studs, and so admit more air space between studs andlead.

Jan 1, 1920

A rotating disc of precipitant zinc in a single stage flow reactor was used to study the effects of deposit mass on the reaction kinetics of copper cementing on to zinc from dilute aqueous solutions.The reaction rate is controlled by external mass transport and the mass transfer coefficient (relative to the original precipitant area) is dependent on the quantity of deposit present. For deposit masses up to about 0·3 mg/cm2 the mass transfer coefficient (first order rate constant) is that expected for the counter-diffusion of reactant and product cations through a laminar boundary layer to a smooth rotating disc. For depositmasses from 0·3 mg/cm2 to about 5 mg/cm2, the mass transfer coefficient increases significantly with deposit mass. For deposit masses greater than 5 mg/cm2 and at least up to 12 mg/cm2, the mass transfer coefficient has again a constant value which is some four to seven times the initial ("deposit free") value. The rate constant for the entire range of deposit masses studied (0 to 12 mg/cm2 ) can be expressed empirically as a cumulative normal distribution of the logarithm of the deposit mass.The enhancement in the mass transfer coefficient for deposit masses greater than 5 mg/cm2 relative to the initial mass transfer coefficient depends on the local operating conditions and increases with increasing disc rotational speed. This enhancement is, however, independent of the previous history of reaction rates.

Jan 1, 1973

In blasting large tonnages of ore or material, the economy of the operation 'depends mainly on the mine manager's judgment in placing the holes to the best possible advantage and in determining the most effective size of hole to suit the conditions and requirements.The placing of holes is often looked upon as a problem involving so many uncertain factors that the application of simple mathematics is impossible. The uncertain factors arise when dealing with strata of different character, in hardness toughness and resistance to shearing.A study of the practice at many mines where all types of strata from hard ore to relatively soft overburden, and even coal, is being mined, suggests that the problem is not as complex as generally believed. There is, without doubt, some uniformity in the amount of burden given to holes of equivalent dimensions, regardless of the material being mined. The reason is simple. With too great a burden hard rock will not break out and soft rock will "bull". The nature of the strata is taken care of by the strength, quantity and distribution of the explosive charge and, to some extent, the spacing of the holes.It is because burdens are uniform in all classes of strata met with in mining, that a formula can be used to design blast hole layouts.The formula introduced in this paper is empirical as it is based on prevailing practice. It has been tested and proved remarkably accurate against every example available to the writer. Many thousands of blast holes, at many different mines, are represented by the examples given in the attached tables; to give further examples would only mean, unnecessary repetition. At the Mount Morgan Mine...

Jan 1, 1952