Search Documents

By A J. Morrison, K Demir, J Kohmuench, K Runge, C Evans

The Eriez HydroFloat® is a flotation device capable of recovering significantly coarser and lessliberated particles than is possible using a conventional mechanical flotation cell. Originally developed for industrial and bulk mineral beneficiation, the HydroFloat® is attracting increasing interest as a means of increasing the required grind size for metalliferous ore flotation. Doing so would reduce the costs of processing complex ores, either by decreasing the energy required to grind the flotation feed or by increasing the throughput achievable with a given comminution circuit. Processing coarser particles would also result in coarser waste streams, potentially improving the mechanical and hydraulic performance of the waste dams that they are sent to. Recent work at pilot – and industrial-scale has proven the potential of the HydroFloat® technology to achieve these gains in metalliferous applications. However, in order to realise the full potential of the HydroFloat® technology, it is necessary to understand not just its performance but also the drivers for that performance. Doing so will allow the design and operation of HydroFloat® devices to be optimised for different ores and applications. For this work, a HydroFloat® pilot rig was deployed to a coppergold plant in Australia and was used to investigate the effect of stream and operating conditions for treating the tailings stream of one of the plant’s rougher flotation cells. Under each set of operating conditions, samples were taken of the HydroFloat® feed, tailings and concentrate streams, and processed to yield the grade and recovery achieved by the device. At the same time, the bubble size and bed behaviour inside the device were measured. This paper presents preliminary relationships observed between the operating conditions and the performance of the HydroFloat® cell, and thus suggests a range of possible drivers for the measured coarse particle flotation performance.

Aug 24, 2022

By D Mather

Fibre reinforced shotcrete has long been accepted as temporary ground support in both mining and civil tunnel linings. Greater knowledge and understanding of shotcrete as an engineering material and advances in its quality have enabled designers to eliminate the requirement of a second pass lining. The initial shotcrete can be used as the permanent tunnel lining or be incorporated into the final lining design, rather than ignored and considered as sacrificial.For the initial shotcrete lining to become a suitable permanent tunnel lining it must be able to establish and maintain stability over time when subjected to all possible loads. To ensure this, best engineering practices are required during the design phase of the project to analyse; ground conditions including rock mass properties, ground and ground water quality, rock mass loadings, excavation sequencing, and construction methodologies.The increased durability of steel fibre reinforced shotcrete over traditional tunnel support, in the right ground conditions, makes it possible to achieve a serviceability design life of greater than 100 years (as required in most infrastructure projects). By specifying a good quality shotcrete mix and ensuring adequate quality control for batching, fibre dosing, preproduction testing, excavation sequencing, and application control, it is possible to eliminate the requirement of a secondary lining. The properties of a suitable permanent lining must be well established using suffi cient preproduction testing in combination with post application monitoring.A major benefit of steel fibre reinforced shotcrete in ground support applications is the removal of any requirement for workers to work under unsupported ground. Its use can also significantly reduce, if not eliminate, the manual handling associated with placing traditional reinforcement such as lattice girders and mesh. Both of these benefi ts are significant with the ever increasing focus on health and safety.This paper highlights factors that must be considered in the design and specifications to enable an initial shotcrete tunnel lining to become the permanent shotcrete tunnel lining.

Mar 8, 2011

By K H. Esbensen

Optimisation of a real-time at-line monitoring system for control of industrial granule coating quality is presented. The system is based on a fluorescence imaging system, because fluorescence originates in the interiors of enzyme granules but is significantly quenched by a polymer coating (which is needed due to environmental precautions). We have developed an image analytical system for direct prediction of coating quality, which is based on application of the Angle Measure Technique (AMT) for image complexity characterisation; AMT is briefly described. The first part of the presentation addresses pixel sampling strategies within a digital industrial image, inherent in application of AMT, in which the unfolded image is regarded as a one-dimensional object in analogy with 1D process sampling in Theory of Sampling (TOS). The effects of random, stratified and systematic pixel selections in the unfolded image are evaluated. Also factors such as the fraction of image pixels and the effects of specific unfolding strategies (there are three principal strategies, termed æchopÆ, æsnakeÆ and æspiralÆ respectively) are investigated. It turns out that unsuspected artifacts are sometimes produced, related to the specifics of the unfolding procedure, which interferes with a straightforward 1D TOS process sampling analogy. These artifacts have a wider interest û among others, for 2D sampling û and therefore receive special attention in this presentation. The optimal pixel selection strategy for the AMT algorithm is found to be systematic or stratified sampling (not surprising according to TOS) of 500+ initiating points, but need to be unfolded in the novel spiral- or snake-wise fashions in order to effectively counteract these artifacts. This also has a general impact on various suggested standard schemes for 2D grid-sampling, among others, from the geoscience realms. The second part of the presentation is directed towards optimal image analytical sampling of a continuous series of fluorescent images (imaging of conveyor belts of æinfinite lengthÆ), ie optimisation of process image sampling. The minimum number of images needed to uphold a sufficiently good on-line estimate of the quality control (QC) parameter in question is found to correspond to the relatively high sampling rate of 15 - 20 per cent, which can be shown to be related to an intrinsic very high measurement error level (25 per cent) of a mandated analytical reference method.

Jan 1, 2005

By S Wellink, D Chalmers, D Adermann, C Martin

The practice of recording blasts for quality control purposes has been conducted for several decades. However, at the low frame rates of a standard video camera, essential data is frequently missed as it occurs when the shutter is closed between frames.The use of high-speed video for the research, development and monitoring of the performance of blasting procedures is a well proven but under-utilised practice.The recent development of low cost, easy to use high-speed digital cameras and user friendly software can deliver a capability into mine management as a day-to-day production tool that can greatly improve blasting performance and reduce costs.Digital high-speed video and image analysis software can accurately quantify each blast. Analysis of the images can facilitate the identification of causes of variance from design, geology changes, errors in blast practice and areas of poor performance. The use of high-speed video greatly enhances the audit and review processes so that future blast design can be quickly and appropriately modified to deliver improved blasting performance and reduced costs.The three videos demonstrate the differences between standard video and high-speed video and the detail that can be obtained from them. These videos of open cut blasts can be used to identify blast performance variances. Capturing images at 1000 frames per second allows the analysis on a millisecond timescale where detonator timings, fragmentation, venting, fume generation and flyrock can be accurately identified.CITATION:Adermann, D, Chalmers, D, Martin, C and Wellink, S, 2015. High-speed video – an essential blasting tool, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 471–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A Reschke

The Thiess John Holland Group is undertaking the design and construction of Brisbane’s Airport Link Project, the largest single investment in transportation infrastructure in Australian history. Twin Herrenknecht TBMs are being used to bore parallel road tunnels from Kalinga Part in Toombul through to Lutwyche, a distance of 2.45 km. At 12.48 m, these tunnel boring machines (TBM) are the largest diameter machines, outside of Japan, to incorporate annular two-component type grouting through the tailskins.Grout design, preparation and injection have been given particular attention in this project in order to push the boundaries of achievement. Laboratory testing was conducted on various mix designs to ensure the contract specifi cations for grout strength could be met. To study the mechanics of the grout injection process, Herrenknecht supplied a test rig which duplicates the grout injection systems on the TBMs. Multiple recipes were tested, carefully selected to balance the requirements of rapid strength development with high mobility (to completely fill the void between the segmental lining and the ground) and minimal bleed.Team Mixing Technologies, Canada, was selected as the grout plant provider based on the technical performance of their high shear colloidal mill mixers. Field results have shown that the colloidal mixer prepared grout gives almost double the strength of an identical grout prepared by a paddle mixer.

Mar 8, 2011

By R Wedmaier

Henty Gold Mine is an underground operation producing 100 000 ounces of gold per annum. The original mining method used was flatbacking with paste fill. However, a non-entry method û uphole benching û was introduced in 1998 to recover the deteriorating crown pillars. Initial challenges were encountered, including poor drilling accuracy, difficulty in charging holes and poor rise performance. These challenges were overcome by a Continuous Improvement Team, consisting of mining engineers, supervisors and miners. Following this, the Team implemented further changes aimed at reducing ore loss and dilution. A second area addressed by the Team was development blasting, where innovative detonator technology known as the ExelTM DevelDetTM was introduced and rapidly accepted by the operators. Continued use of the ExelTM DevelDetTM resulted in a number of benefits, such as easier bogging, less perimeter damage, faster charging and hook-up and decreased wastage. Finally, improvements were made in the area of explosive handling, where competency-based training of operators was conducted and manual handling of ANFO has been significantly reduced by the introduction of the MiniMoverTM into the underground magazine.

Jan 1, 2001

By F Phillips, E Deucker, J Kato

It is challenging to determine the optimal mining strategy to maximise value when a mine plan includes mineralised material which does not meet the full cost of mining but has value exceeding the variable cost of mining (‘marginal material’). Mining too much marginal material dilutes the operation’s head grade and undermines profitability. Conversely, leaving too much metal behind fails to achieve the full value of the endowment. Finding the balance between the two will maximise value delivered from the asset. This dilemma has traditionally been approached by calculating a suite of cut-off grades to define the grade of material that meets economic targets for an orebody (or zone within) and should therefore be included in the mine plan. A problem with this approach is that individual mining blocks within the zone have different costs, value and confidence levels, with each having economic co-dependencies between them. Blocks of identical grade but different mining contexts will have distinctly different economic outcomes. For example: • a block may be a low-grade increment or shell around a higher-grade stope; • a block may be available to be mined when there is spare mining capacity; or • a block may defer access to significantly higher cash flow material. Each of these circumstances would result in different value from the blocks if included as part of the mine plan. Cut-off grades calculated as averages over zones of material, or in isolation from schedule-based information, are missing the entire mining context that determines the ultimate economic outcome of making a mining decision. There are tools and techniques available to address this for open pit mining, however underground mining has different nuances. There are more intricate economic and physical dependencies between potential ore blocks, and importantly, the decision to leave material in situ can be made at any time. The case study in this paper explores a new methodology for underground mining, targeted towards strategic planning applications. It examines whether the economic logic usually applied via cut-off calculations can be implemented in the schedule so that optimal economic decisions can be made on a block-by-block basis, taking into account the mining context of the block, with the objective to maximise asset value. The results of the case study scenarios in Table 1 demonstrate the magnitude of the potential improvement in NPV that can be attained by a block by block valuation approach

Mar 15, 2021

By J Ta’ala, M Handyside

Mechanical sampling from conveyors has historically been a staple in the iron ore industry when information related to chemistry, sizing and moisture is required. In order to comply with ISO 3082:2009, samples can be taken either on a mass or time basis provided no bias is introduced by periodical variation in quality or quantity. With the introduction of mechanical sample carousels, you also have the opportunity to collect samples on a mass or time basis. In order to optimise automatic sample stations in a changing production environment, BHP Billiton Iron Ore (BHPBIO) has developed a simulation model that enables the various combinations of mass–mass, mass–time, time–time and time–mass to be investigated.The sample station model can utilise actual (variable) feed rates to achieve high resolution and enables the simulation of sample size variation. Cutter speeds and other settings can then be adjusted to better optimise the performance of the sample station with regards to optimal sample size as well as ensuring the sample station is in compliance with ISO 3082. The model can also assist process engineers in adjusting settings to better optimise the sample station and reduce unwanted events such as blockages. The model can be easily modified to conform to various sample station designs. This paper demonstrates the use of the model and the benefits that can be achieved.CITATION:Handyside, M and Ta’ala, J, 2014. Simulating time versus mass basis?sampling, in Proceedings Sampling 2014 , pp 155–164 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

The Chamber of Minerals and Energy of Western Australia Inc (CME) is the peak resources sector representative body in Western Australia. The paper gives a summary of the role and objectives of the CME, including its history, structure and key program areas. Particular attention is given to the role of the CME in the Eastern Goldfields of Western Australia. The paper details the types of CME membership that are currently in existence. The paper argues that a strong and vibrant CME is vital to secure the resources sectorÆs growth and development in future years.

Jan 1, 2006

By Coates D. F, Neil T. J, O&apos

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risks of slope fail- ure inherent in steeper slope angles. However, no formal framework for a proper analysis existed to date. This paper describes the results of the past four years' effort in which a formal eco- nomic analysis framework was developed and tested through a case study. This framework, in essence, consists of the availability of tested procedures and com- puter programs. The procedures as well as the programs are divided into two broad functional categories; (1) the first category related to assessing the economic benefits and costs associated with various pit slope angles and (2) the second category that determines the overall financial impact which the assessed benefits and costs exert to the mine operator's overall economic stature.

Jan 1, 1977

By Song Yongxue

During the design and operation stages of a block caving project, a large amount of research and development work has been undertaken in the Tongkuangyu Copper Mine. This paper presents the research achievements from these studies, including a rock mass quality evaluation method, cavability prediction, fragmentation evaluation, caving mechanisms, a computerised production scheduling model and the optimised draw control system. The main features of the block caving system in the Tongkuangyu Copper Mine are also discussed.

Jan 1, 2000

By D M. Brady

Underground coal mines in Australia have embraced the use of various inertisation techniques both proactively and reactively. The use of such techniques can have a significant influence on ratios and trends used to monitor the status of the underground environment. Whilst control strategies should never be ignored in favour of preserving the integrity of ratios, the influence and significance of the changes likely to be seen should be anticipated and understood for reliable interpretation of the situation. This paper looks at the influence inertisation techniques can have on results and subsequent interpretation.CITATION:Brady, D M, 2013. The influence of inertisation techniques on gas interpretation, in Proceedings The Australian Mine Ventilation Conference , pp 259-264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By J Euston

In the 1990s round flotation tanks were introduced as a result of the lower fabrication costs for larger cells. It was soon observed that round tanks held a number of further advantages over the traditional rectangular cells, such as better hydrodynamics, lower costs and reduced footprint per unit volume.In the last twenty years flotation cell sizes have increased almost exponentially and designs of 250 to 300m3 are a well established standard with plans for full scale pilot installations of 500m3. The option to install these large cells gives flexibility in circuit arrangements and allows efficient and economic matching of flotation lines with modern mill designs. The benefits of scale up are well known with reduced numbers of cells required, lower power costs per unit volume, etc. These benefits will be briefly reviewed with specific reference to the installation of 300m3 to 350m3 flotation cells at the Copperton Concentrator of Kennecott Copper in Utah, USA.The sophisticated techniques required to model these ‘supercells’ have led to a critical review of the fundamentals of flotation science and engineering. In addition to outlining the advantages of large flotation cells, this paper will review the science which supports, and occasionally challenges, the ongoing trend to larger flotation cells.

Aug 8, 2011

By C Vejrazka1

The occurrence of airblasts is one of the principal mining hazards in caving operations between the time of cave establishment and breakthrough of the cave to surface. As such, it needs to be managed continuously and risk assessments need to be reviewed on a regular basis for applicability to changing conditions. The likelihood of an airblast occurring is based on a range of geotechnical factors over some of which engineers on-site only have limited control. However, the impact of an airblast to the underground mine, if it does occur, can be managed by following established safety guidelines for the production from the cave.This paper outlines how the Caving Airblast Simulation Tool in Ventsim was used to determine a risk management strategy for a sublevel and a block cave at a mining operation in Australia. The block cave has a footprint of 14 500 m2 with the extraction level located 1250 m below surface while the sublevel cave currently has a footprint of around 18 000 m2 operating between 660 m and 800 m below surface. Both caves are currently in their early operational periods. The risk analysis provided valuable information for the production planning of the caves including confirmation of extraction ratios for the block cave undercut, locations of airblast walls and maximum allowable air gaps for different muck pile heights to ensure safe operation is achieved.

Oct 12, 2022

By K Faure

At Sams Creek a peralkaline granite porphyry dyke hosts gold-bearing sulfide-quartz-siderite veins. The granite dyke intrudes Ordovician-Silurian metapelite and quartzite, and has thin lamprophyre dykes along its contacts. The mineralised veins and the granite and lamprophyre dykes have been deformed during several phases of folding, the youngest of which is Early Cretaceous. The granite has been hydrothermally altered, with early magnetite-siderite¦biotite alteration overprinted by sulfide and quartz-siderite veins and quartz-perthite-albitesiderite-pyrite-rutile¦sericite alteration assemblages. The sulfide veins are composed of arsenopyrite + pyrite ¦ gold ¦ galena ¦ sphalerite ¦ chalcopyrite ¦ pyrrhotite ¦ graphite, with minor quartz and siderite. The gold contains significant silver (up to 30.8 wt per cent) and ranges in fineness from 692 to 844. Immiscible liquid-rich fluid inclusions, in quartz protected from recrystallisation by enclosing arsenopyrite, contain carbonic liquid that homogenised at temperatures of 320 - 355¦C. The Sams Creek gold deposit is distinguished from the orogenic gold deposit type by its stockwork veining, magnetite-siderite¦biotite alteration, high sulfide content, ore mineralogy and the absence of mineralisation in the metapelite country rocks. Features of the Sams Creek gold deposit do not fit neatly into existing classifications of granite-related gold-bearing deposits. The peralkaline composition of the Sams Creek granite and the absence of molybdenite and paucity of chalcopyrite, are major points of difference with gold-rich porphyry copper deposits. The presence of a lowsulf idation-state ore mineral assemblage, carbonate alteration and carbonic fluid inclusions at Sams Creek are typical of many of the reduced granitic intrusion-related type of gold deposit. However, notable differences are: the reduced type granites are metaluminous and calc-alkaline; and Sams Creek only has high As in contrast to elevated Bi, W, As, Mo, Te, and Sb in the reduced type. The Sams Creek deposit also shows affinities with gold deposits associated with alkaline magmatism, and it appears to be a new variant of this type as an As-Au deposit associated with a peralkaline granite and lamprophyre.

Jan 1, 2004

"Recognising that the mining industry is wedded to the break-even cut-off grade rather than a cut-off grade that optimises value, the author examines some perils and pitfalls in the use of break-even grades that lead to what the author calls ‘negatively geared ore reserves’.Negatively geared ore reserves occur when a portion of the ore reserves actually has a negative value and is effectively being subsidised by the more profitable portion of the ore reserves. This situation is generally difficult to detect with the level of information available to the public investor. The ore reserves can still be quite profitable in total, but now possess a level of risk that may not be appreciated.The risk profile (financial risk) of a negatively geared ore reserve is far greater than for a non-negatively geared ore reserve. Like a negatively geared investment property in a falling property market (for readers familiar with the Australian tax minimisation investment strategy), when the price of a commodity falls, a company that possesses a negatively geared ore reserve loses value at a magnified rate relative to a company that has a neutral or positively geared ore reserve. In the extreme case of a major commodity price reduction, as happened with the gold price in mid-2013, the negatively geared ore reserve can easily become negative value in total, not just in part.The negatively geared ore reserve is sometimes intentional – for instance in order to increase published ore reserve tonnages and meet the CEO’s key performance indicators – but is also often unintentional, resulting from various errors in the break-even calculation. Common errors in calculating a break-even grade include using fixed metallurgical recoveries, not including allowances for ideal laboratory versus real plant results, ignoring available operational data and using modal rather than mean parameter values in cost and performance calculations.This paper examines a common value distribution profile in many ore reserves and the effect of common break-even grade errors on this profile.CITATION:Poniewierski, J, 2016. Negatively geared ore reserves – a major peril of the break-even cut-off grade, in Proceedings Project Evaluation 2016, pp 236–247 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By S Moradi

The thickener overflow of zinc concentrate, obtained from flotation process in the Angouran plant located in Iran, contains a large quantity of slimes which were transferred to the tailing ponds. These slimes have caused problems of storing and environmental aspects in the Angouran area. The objective of this research is to describe the extraction of zinc from these slimes by leaching method using sulfuric acid in pilot plant scale.Chemical analyses showed that these tailing materials contain 35 per cent of zinc. By XRD analysis, smithsonite is identified as the major constituent. Calcite, dolomite, and cerussite are found as carbonate minerals. A minimal amount of Zn occurs as hemimorphite. Quartz, kaolinite, clinochlore and muscovite are other silicate minerals in the slimes.In the optimal conditions, ie acid leach at pH of 1, temperature of 55¦C, reaction time of 120 minutes and solid-liquid ratio of 1:3 and neutralisation with Ca(OH)2 at pH = 4.5, temperature = 70¦C, time = 90 minutes, the total recovery of zinc obtained was 95 per cent.

Jan 1, 2004

By B Taylor

The Perseverance deposit is the most southerly known economic copper/gold deposit within the Cobar gold field. The deposit is situated approximately 12 km to the south-southeast of Cobar and is essentially blind to surface with the top of economic mineralisation occurring 750 m below ground level.Based on the December 2010 resource estimate (inclusive of reserves and net of depletion) the deposit contains 3 011 000 tonnes at 6.1 g/t Au and 0.90 per cent Cu (590 000 oz of gold and 28 000 tonnes of copper). The deposit is comprised of four principal lenses, the Perseverance, Hulk, Zone B, and Hercules lenses. In excess of 90 per cent of the known resource tonnes are contained within the Perseverance and Hulk lenses. The deposit is shear related and hosted within lower Devonian rocks of the Cobar Basin. The competency contrast of rhyolites juxtaposed against sediments by the Peak-Perseverance shear is the principal control on mineralisation. Both the Perseverance and Hulk lenses are primarily hosted by brecciated rhyolites juxtaposed against Chesney formation sediments across the Peak-Perseverance shear. This faulted rhyolite sediment contact roughly defines the global orientation of the deposit. The Perseverance lens continues within the shear for up to several hundred metres beyond the extent of the faulted rhyolite sediment contact. Mineralisation within the shear beyond the faulted rhyolite contact zone is hosted by sheared silicified sediments. The Perseverance lens remains open at depth and to the south.The Zone B and Hercules lenses, which are significantly less important in tonnage terms, are hosted by rhyolite breccias within the main body of the rhyolite and appear to be only tenuously related to the Peak-Perseverance shear. Within the Perseverance lens, the presence of northeast trending high grade breccia veins developed oblique to the north-south trending shear system has led to the development of steeply north plunging high grade ore shoots within a globally north-south trending mineralised domain. These high grade shoots have limited horizontal continuity but significant down plunge extent.The presence of coarse gold and the resulting strongly skewed nature of the gold grades, in conjunction with controls on mineralisation which are not parallel to the mineralised domain, has led to predictive difficulties regarding stope performance.Strong heterogeneity of the gold content of the ore and geological controls on mineralisation which are not parallel to the global trend of the mineralisation impose a set of difficulties which sound geological control is helping overcome.

Aug 22, 2011

Sampling of CIL/CIP circuits is typically done by compositing samples of feed and tails over eight or 12 hour periods. As the residence time in the leaching tankage may be approximately 20 hours, the tails from any period being derived from material entering the circuit 20 hours earlier do not correspond to the head from the same sampling period. Moreover, mixing in the series of tanks in a circuit also modifies correspondence between input and output. A special purpose simulator has therefore been developed to allow for the mixing and delay in the tankage and permit estimation of the head assays corresponding to any tailings sample. Thus more accurate assessment of the day-to-day recoveries of gold and silver follows. The model, programmed in Excel, assumes that the tanks are perfect mixers. By inputting the sequential head grades and considering that no leaching has occurred, the head grade which corresponded to the tailings for each period could be estimated. Allowance is made for variations in feed rate over the sampling period by computing the average flow rate of slurry and thus the residence time of each increment of the tailings. This simple model and its application have been found to be subject to some limitations, which are discussed in the paper, resulting in some unresolved variability in results. However, for a typical circuit even the simple model was able to greatly improve consistency of recovery data with variations being approximately halved by eliminating much of the anomalous variation arising from the lack of correspondence between head and tail when changes in head grade are occurring. Therefore, this permits genuine variations in metallurgy to be identified with greater confidence and thus operational shortcomings can be identified and addressed more quickly.

Jan 1, 2006

By E J. Sellers, A Cocker

Movement of the fragmented rock mass is an inevitable consequence of open cut blasting. Uncontrolled, unaccounted movement from blasting commonly causes ore loss and dilution from waste mixing. Therefore, the prediction of the post-blast location of both ore and waste is vital in grade control and of direct interest to mining geologists. Direct measurement techniques have matured significantly over the past decade, but their use remains expensive and labour intensive. Access and safety issues are further disincentives to regular movement monitoring. What is needed is a combination of direct measurement to establish baselines and reliable predictive modelling.The W H Bryan Mining and Geology Centre of the University of Queensland has pioneered 3D blast movement modelling using ‘physics engines’ to handle in-flight collisions and predict the final resting place of blasted material. Open cut metalliferous mines are a demanding environment for this style of modelling as they can involve complex geometries and variable buffering, which leads to inconsistent confinement. A version of the model designed to deal with these complexities is under development. A well-controlled field trial was needed to validate this new version.A validation trial was completed at a gold mine in South-East Asia. The aim was to increase throughput by increasing the blast powder factor without losing grade through dilution and mixing with waste. Four blocks were blasted to identify the effect of bench height and face confinement on ore movement, fragmentation and process throughput. The powder factor and blast timing were kept constant. Movement of the broken rock was measured by placing blast movement monitors at known positions in the block and then locating them after the blast. The majority of sensors were recovered, providing a unique insight into blast movement dynamics and generating a substantial data set for model validation.The model (called ‘MetaMove ‘) was calibrated for one blast and applied to investigate the extent of grade loss and possible mitigation strategies. Conventional mining techniques that involved firing across the strike of the orebody, and no post-blast boundary adjustment of the ore/waste boundaries prior to digging, were found to cause up to 44 per cent loss of high-grade ore, depending on the grade distributions. Post-blast adjustment of the ore/waste boundaries can negate this loss. The model indicates that altering timing and ensuring that the block boundaries are well confined can further constrain the movement of ore/waste boundaries. Thus, the model can be successfully applied to minimise grade dilution and limit misclassification of ore as waste whilst using higher powder factors to increase mill throughput. Application of a calibrated model to move ore/waste boundaries prior to digging will enable the production geology team to add significant value to the mining operation.CITATION:Cocker, A and Sellers, E J, 2014. Modelling blast movement for grade control at an open cut gold mine, in Proceedings Ninth International Mining Geology Conference 2014 , pp 377–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014