Search Documents

By J Zhou, T D. McGrath, K P. Galvin, C P. Lowes, J J. Eksteen

Pre-concentration of low grade ores can improve the economic and environmental sustainability of an operation significantly, with opportunities for implementation ranging from run-of-mine to mill discharge depending on ore specific characteristics. For a gravity separation, where the performance is fundamentally constrained by mineral liberation, these feeds often represent a very difficult separation given the dominance of the relatively coarse gangue and fine liberation sizes. Thus, building knowledge of the feed through characterisation of the density distribution is critical to assessing amenability before progressing towards lab/pilot-scale test work and full-scale operation. The traditional approach to determining the density distribution typically involved sink/float testing, however, recent developments in hydrodynamic fractionation using inclined channels now offers a more cost-effective alternative with minimal health and environmental risk. A non-hazardous dense liquid, namely an aqueous solution of lithium heteropolytungstates (LST), is supplied as fluidisation to a REFLUXTM Classifier, consisting of a vertical section below a system of inclined channels, operating in semi-batch configuration. Fractionation is achieved by increasing the flow rate incrementally and collecting the particles to form a series of flow fractions. The purpose of this paper is to present this new method in the form of a case study, aimed at assessing the amenability of a low grade gold-bearing sulfide ore to pre-concentration. The robustness in the method is demonstrated through comparison with sink/float data, examining the density distribution and the liberation-limited product grade and recovery achievable. These data are then used as a benchmark to assess water-based continuous gravity separations conducted on the feed using a laboratory-scale REFLUXTM Classifier. This data set is used as the basis for process modelling and empirical validation for the recently established partition surface of the separator.

Nov 10, 2020

By S Hanke, J Burden, P Spies

The Waterview Connection will complete Auckland’s long-planned Western Ring Route, a 48 km north-south motorway alternative to State Highway 1 that bypasses the central city to the west. The project involves construction of 5 km of new motorway – half of it underground in tunnels – to connect the Southwestern (State Highway 20) and Northwestern (State Highway 16) motorways.The Western Ring Route will link the major population and industrial centres of Manukau, Auckland and North Shore to give the region the connected and resilient strategic road transport system it needs to underpin economic growth and sustainable development. It will also provide a direct motorway link between Auckland’s central business district (CBD) and international airport.The project involves construction of twin 2.4 km driven tunnels with an outside diameter of 14.41 m beneath residential suburbs, a major arterial road and a rail corridor. Enabling works began in January 2012 while tunnel construction using an earth pressure balance (EPB) tunnel boring machine (TBM) began in November 2013.This presentation introduces the Waterview Connection project, its role in the development of the Auckland motorway network, its procurement process, the alliance delivery model and an overview of the project’s design features and construction progress to date.Design and construction highlights of the presentation include the TBM start-up, turnaround and breakthrough arrangements as well as the experience gained during the first tunnelling drive. The presentation also covers an innovative process developed for invert construction behind the TBM that is independent of tunnel excavation.CITATION:Spies, P, Burden, J and Hanke, S, 2014. The Waterview Connection Project – progress to date, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 519–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By H Fukaya T Miki, J Gamutan

Molybdenum disilicide (MoSi2) is a promising material for thermal applications due to its excellent heat and oxidation resistance. It can operate at temperatures of up to 1800°C as furnace heating elements and protect refractory metals such as molybdenum from rapidly reacting with air to form volatile molybdenum oxides at elevated temperature. In this work, the feasibility of forming MoSi2 on a molybdenum substrate by hot dipping in a silicon-saturated molten metal bath was investigated. This method is simple, predictable and can be used to coat large components and complex parts. It was found that tetragonal MoSi2 can be successfully synthesised on the surface of the substrate after dipping for 15 mins at 1000°C using molten tin (Sn), bismuth (Bi) and copper (Cu) baths. The growth of the MoSi2 layer was fast within the first 15 mins and then gradually slowed down with time. After dipping for 60 mins at 1000°C, the thickness of the MoSi2 layer were measured as 441.5, 19.5 and 13.1 μm for the copper, tin, and bismuth baths, respectively. The MoSi2 coating synthesised in this study provided oxidation resistance at 1150°C by forming a protective SiO2 layer on the surface. The SiO2 layer prevented the sample from rapidly oxidising by inhibiting direct contact between the molybdenum substrate and oxygen in the atmosphere. Compared to conventional methods, the proposed hot dipping method produces a MoSi2 layer more rapidly and at much lower operating temperatures. This makes it a more attractive option for coating large and complex components, with the potential to enable the use of MoSi2 in a wider range of applications.

Jun 19, 2024

By K J. McDonald

All commercially available zircon sands contain radioactivity sourcing from the decay of trace amounts of contained uranium (U) and thorium (Th). The fine particle size zircons of the Horsham area in the Murray Basin region of Victoria, Australia, contain significantly more (about twice) Th+U than those commercial zircon sands. The marketability of these fine-grained zircon sands is likely to rely on the removal of these radioactive impurities. CSIRO Minerals have been working for some time to develop processes for the removal of the radioactive impurities from zircon. It is generally agreed that it is quite impossible to leach U and Th from zircon, however, the Heat and Leach (HL) process, described in detail in Aral and McDonald (1999), reduces the radionuclide levels significantly. The identified (HL) process aims to leach uranium and thorium selectively from a decomposed zircon. The novelty of the process is that a large part of the leached product can be reconstituted to a low radiation zircon by a subsequent heat treatment. The HL process uses a flux mixture of sodium carbonate and calcium borate to decompose the zircon at relatively low temperatures (900 to 1150¦C) and a weak acid (0.5M HNO3; 80¦C/0.5 h; pulp density ten per cent) to leach the radionuclides selectively. The process leaves the major components (ZrO2 and SiO2) behind with little loss. The HL process for example lowers the U+Th content of a Murray Basin zircon from 1000 ppm to 400 ppm U+Th. Among the radionuclides more U progeny is removed than the Th series radionuclides. This is very significant as the radioactivity of U series is 2.5 times more that from the Th series. Therefore the reduction in the radioactivity level of zircon is more than the reduction in Th+U indicated by XRF analysis. A schematic flow sheet of the HL process is shown in Figure 1. Although the HL process successfully lowers the radionuclide levels in zircon sands, the final product contains significant amounts of sodium (up to 14 per cent Na2O) and small amounts of CaO. By comparison, the sodium content of the commercial zircon sands is in general 2O. Zircon is used mainly as an opacifier in tile glazing where the addition of ten to 15 per cent zircon to a translucent base glaze gives the sanitary white colour to the tile surface. Opacification is the result of the refractoriness of zircon particles at the glaze firing temperatures that is generally around 1050¦C.

Jan 1, 2001

By H Jalalifar, N Aziz

In the ten years since the University of NSW proposed a pillar design methodology for bord and pillar operations, the Australian coal mining industry has changed substantially. What was primarily a bord and pillar design approach is now being applied to chain pillar design in longwall mines where the requirements are substantially different. The dimensions of chain pillars can impact on tailgate conditions (roof, rib and floor), seal performance, and surface subsidence. The status of chain pillar design practice in Australia is reviewed, with a focus on defining pillar strength, chain pillar loading, and assessing the performance of the roof/pillar/system. A new pillar strength equation is proposed for Australian coal that applies for all width/height ratios. An alternative analysis of probability of failure of chain pillars is presented.

Jan 1, 2005

By J Andrina, D Richar, R Smart, A Neale

The Grasberg is a large copper and gold open pit mine operated by PT Freeport Indonesia and located in the high equatorial mountains of Papua Province, Indonesia. The climate is alpine/sub-alpine with little seasonal variation in temperature and rainfall. The annual precipitation varies from about 3000 to 5000 mm over short distances around the Grasberg, but in general, an average daily precipitation of 10 mm per day applies and leaching of the overburden is continuous throughout the year. Mining commenced in 1988, and almost all of the overburden mined up to 2003 was potentially acid forming. From 2003 to the end of the Grasberg pit operation in 2014, approximately 70 per cent of the overburden will be potentially acid forming and 30 per cent limestone. A major focus of the investigations is developing strategies to maximise the beneficial use of the limestone that will be mined. Laboratory columns and field test pad investigations have been ongoing for six years examining limestone blends. Trial dumps utilising truck placement and conveyor/stacker placement and blending of limestone and acid generating rock have recently been constructed. In addition, based on initial results, investigations aimed at further evaluating the performance of limestone covers in this high rainfall environment have commenced. A significant finding has been the identification of strong armouring layers on sulfide surfaces within well-blended material and under limestone covers. These layers effectively isolate sulfides and thus progressively slow the oxidation rate to a level where the alkalinity load from the limestone exceeds the rate of acid generating. ARD is controlled and neutral low metal drainage results. The results have demonstrated that although limestone blending is effective, it is necessary to ensure that all size fractions within the blend receive adequate acid neutralising capacity to buffer the potential acidity. Because the sulfur content generally increases and the acid neutralising capacity decreases with decreasing particle size in limestone blends, the amount of limestone required greatly exceeds the stoichiometric requirement. This paper describes the development of limestone blending specifications for potentially acid forming overburden and presents the results of the ongoing limestone cover trials at the Grasberg mine.

Jan 1, 2003

By K J. Davey, J T. Woodcock

Australian steelmakers produce up to 30 000 t/yr of electric arc furnace (EAF) dust. Current disposal techniques include sending EAF dust to landfill, stockpiling, and paying zinc smelters or registered waste removalists/processors to take the dust. Many of the complex overseas pyrometallurgical and hydrometallurgical treatment routes cited in the literature are not considered economic. Governmental, environmental and social pressures on producers to consider more sustainable disposal options are mounting, and there is now a strong push to consider recovering potentially valuable or recyclable components, such as zinc and iron units, from EAF dust. As well, there remain strong economic drivers for producers to find lower cost disposal solutions. Characterisation studies undertaken at CSIRO Minerals have revealed important physical differences in the nature of the zinc- and iron-bearing phases contained in domestic EAF dusts. These differences have been exploited using simple and cheap mineral processing techniques such as water washing, wet cycloning and wet magnetic separation. This has allowed a significant upgrade in the zinc content of EAF dust to be achieved, together with a reduction in the levels of key smelter penalty elements, such as chlorides and fluorides. The zinc-rich portion of the dust is now a more attractive smelter feed while the iron-rich part of the dust could potentially be briquetted or pelletised with a reductant and recycled to recover iron, and thus close the loop on dust processing. The basis of the separations tested together with laboratory results from several Australian dust samples are presented and discussed in this paper.

Jan 1, 2006

This research is about human development and socio-economic progress of the main mining areas of Chile in the period 1990 - 2007, and especially about the positive effects that mining activity has on poverty reduction and indicators related to the Millennium Development Goals of the United Nations. The analysis is doubly interesting, if one considers that the economic and social developments in Chile, recognised and prominent among the Latin American economies and developing nations, are more evident in mining areas as Tarapacß and Antofagasta (northern Chile), which concentrated than more 70 per cent of investments and mining assets in the country. Additionally, the study concludes with methodological reflections for the evaluation of socio-economic impact in the mining industry in developing countries.

Jan 1, 2009

By M M. Hilden, M S. Powell, B Foggiatto

In an environment of decreasing ore grade, increasing costs and uncertainty with respect to commodity prices, the industry could benefit from evaluating alternative technologies and innovative circuit configurations. The flexible circuit approach suggests that the design of grinding circuits can be adapted to changes in feed properties and economic conditions. Advances in modelling and simulation are enabling metallurgists to predict the performance of more complex circuit configurations with increased confidence. Ore variability information and processing costs may be used as modelling inputs to determine the optimum processing conditions at a given time. A case study has been completed demonstrating the value of combining a flexible circuit with a model-based optimisation of the process. Ore properties and equipment performance data obtained in operating plants have been used to model and simulate flexible circuit configurations.This paper explores strategies to introduce flexibility to existing circuit configurations when processing ores with high variability. Multicomponent models incorporated in the model developers’ kit (MDK) allow the simulation of more complex and flexible circuits. This capability enables demonstration of the potential to enhance metal production through adapting processing routes according to the ore type being processed. The simulation of different flow sheet configurations allowed the definition of the best option for maintaining the metal production when treating lower grade ores, highlighting the advantages of flexible circuit configurations compared with a one-process-fits-all approach.CITATION:Foggiatto, B, Hilden, M M and Powell, M S, 2014. Advances in the simulation of flexible circuits, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 391–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D Anderson, W Timms

"A geotechnical centrifuge can characterise and model the interaction of tailings and fluids over very long time periods by accelerating drainage and consolidation processes. This technology can be considered an environmental ‘time machine’ for designing and evaluating tailings storage projects and verifying numerical models. The Broadbent G-18 geotechnical centrifuge (2 m diameter, up to 875 rev/min) and associated equipment is a unique facility commissioned in 2011 at UNSW Australia for applied research in low-permeability materials such as mine tailings. Two centrifuge modules are available: the permeameter module for characterisation and physical modelling and the strongbox module for physical modelling.This paper presents examples of geotechnical centrifuge applications for the: consolidation of slurries and dewatering design of earthen barriers compatible with tailings chemistry prediction of contaminant mobility. The specifications and capability of the UNSW Australia geotechnical centrifuge and associated instrumentation is also presented, along with preliminary analysis of the confidence intervals associated with permeability testing of a set of samples of varying heterogeneity. Drainage velocity through a mine tailings sample increases linearly with g-level in the centrifuge permeameter until tailings consolidation occurs. Alternatively, geotechnical centrifuge experiments can be designed to limit consolidation so as to quantify permeability changes that may occur with geochemical interactions between fluids and mine tailings or earthen containments. Reactive solute transport through mine tailings can be simulated at realistic solid:liquid ratios when chemical equilibrium is maintained during geotechnical centrifuge testing. Carefully designed physical models of tailings disposal tested at accelerated gravity can therefore provide a realistic evaluation of tailings consolidation and drainage and the potential for subsurface migration of contaminants from mine tailings over long time periods.CITATION:Timms, W and Anderson, D, 2015. Geotechnical centrifuge technology for characterising the interaction of tailings and pore water over decadal time periods, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 247–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By P N. Nkrumah, A van der Ent, G Echevarria, P D. Erskine

Nickel phytomining is a low cost alternative to traditional nickel mining and a complementary process to existing mining operations in areas with low-grade nickel soils or nickel waste material. The process of nickel phytomining consists of growing selected hyperaccumulator plant species (‘metal crops’) on Ni-rich (ultramafic) soils, followed by harvesting and incineration of the biomass to produce a ‘bio-ore’ from which Ni salts or Ni metal may be recovered (Chaney et al, 2007). The ‘metal crops’ are selected on the basis of high biomass yield combined with high Ni concentrations (>1 per cent) in the above-ground biomass (Chaney et al, 2007). Currently, Alyssum murale and A. corsicum have been used for Ni phytomining trials, mainly undertaken in Albania and USA (Bani et al, 2015; Li et al, 2003), while the agronomy of <10 species has been tested in temperate regions (Nkrumah et al, 2016). Nickel phytomining has high economic potential; however, large-scale demonstrations are needed to provide ‘real-life’ evidence for commercial operations (van der Ent et al, 2015). Unrealised opportunities exist in tropical regions for commercial scale Ni phytomining. To date, the agronomy of tropical ‘metal crops’ has not been tested. This extended abstract presents the progress of tropical phytomining, and reports on agronomic trials undertaken to determine whether the trends in temperate regions could be confirmed in a wet tropical environment.CITATION:Nkrumah, P N, Erskine, P D, Echevarria, G and van der Ent, A, 2016. Progress in tropical nickel phytomining, in Proceedings Life-of-Mine 2016 Conference, pp 135–137 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By J Ferreira

To speed up multivariate geostatistical simulation it is common to transform the set of attributes into spatially uncorrelated factors that can be simulated independently. One decorrelation method is the method of minimum/maximum autocorrelation factors (MAF), where a two structure linear model of coregionalisation is assumed. The transformation decorrelates the theoretical model exactly, but the actual data are only approximately decorrelated. The MAF transformation can therefore be seen as a special case of a non-orthogonal approximate diagonaliser of a set of symmetric matrices. A more general approach for approximate joint diagonalisation (AJD) has been developed in the context of blind source separation. For these AJD algorithms no assumptions are made beyond symmetry of the individual matrices and so they can be applied to a family of experimental semivariogram matrices. In their application there are no restrictions on the number of structures in the linear model of coregionalisation (LMC) thus removing one of the conditions placed on the subsequent modelling of the spatial structure of the factors. In this paper the general background for the U-WEDGE AJD method is presented. It is shown that the U-WEDGE method achieves better spatial decorrelation than the MAF method. The factors derived from U-WEDGE are simulated using conditional turning bands simulation and then backtransformed to attribute space.

Sep 26, 2011

The mining industry is quite often faced with declining selling prices for its products in the face of rising prices for the input cost resources that it uses. Blasting is a key activity within the mining system and has a vital role to play within the Mine to MillTM concept. It is therefore important that blasting makes a positive contribution to mine profit and productivity. There are several variables involved in considering the profitability and productivity of blasting. The rock types and structures, the bench height, the blast hole drill rig specifications, hole diameter, spacing and burden, explosive loading and initiation and blast size fragmentation. Productivity accounting is a methodology which is used elsewhere to give additional insights into the productivity and pricing factors that drive the financial performance of a business. Miners know intuitively that productivity and pricing influence costs and profit, but only with productivity accounting can the dollars involved be calculated. Drilling and blasting are part of a chain of unit operations in a mine. For an owner-miner, drilling and blasting would be considered as cost centres and a productivity accounting cost model approach would be relevant. On the other hand a contractor is likely to consider drilling and blasting as a profit centre, in which case a productivity accounting profit model approach would be appropriate. Both of these will be explained. The paper provides a basic outline of deterministic productivity accounting and demonstrates its application to blasting. Drilling and blasting data from a mine was obtained for a two-month period. The change in productivity and prices was calculated to obtain the dollar contributions from them towards the change in cost. It was determined that although there had been productivity dollar gains these were offset by larger pricing dollar losses, the net effect being that total drilling and blasting costs increased. The productivity accounting analysis gives the facts and the mine is in a position to establish priorities based on knowing the dollar contributions of each input used.

Jan 1, 2001

By Warren L. J

The recovery of phosphate minerals from the Mt Weld deposit by froth flotation has been studied by many researchers. Most of the flotation experiments were carried out with a tall oil fatty acid as collector and sodium silicate as dispersant and gangue depressant at pH about 10. Several rougher stages and cleaner stages and, sometimes, a desliming stage were included. The major difficulty was to reduce the Fe2O3 impurities in the concentrate to the required level. We used QEM*SEM (Quantitative Evaluation of Materials by Scanning Electron Microscopy) to provide a comprehensive and accurate mineralogical analysis of the flotation products. The analysis indicated that the Fe2O3 impurities were mainly recovered in the second concentrate, owing partly to the incomplete depression of the liberated iron oxides by the sodium silicate and partly to composite particles containing iron oxides. The selective depressing action of sodium silicate was improved by adjusting the variables such as the modulus (SiO2/Na2O), pH and time of standing of the stock sodium silicate solutions or by adding some polyvalent metal salts into sodium silicate solution. The flotation process was optimised to produce a phosphate concentrate with the required grade and recovery (38.6 per cent P2O5, 2.67 per cent Fe2O3, 13.7 for P2O5/(Fe2O3 + A1203), at P2O5 recovery of 81.5 per cent). The possibility of recovering the rare-earth phosphate, monazite, from the Mt Weld deposit by flotation was also studied.

Jan 1, 1991

By A Woodley, N C. Kunz

A mine site water balance is important for communicating information to interested stakeholders, for reporting on water performance and for anticipating and mitigating water-related risks through water use/demand forecasting. Gaining accuracy over the water balance is therefore crucial for sites to achieve best practice water management and to maintain their social license to operate. For sites that are located in high rainfall environments the water received to storage dams through run-off can represent a large proportion of the overall inputs to site; inaccuracies in these flows can therefore lead to inaccuracies in the overall site water balance.Hydrological models that estimate run-off flows are often incorporated into simulation models used for water use/demand forecasting. The Australian Water Balance Model (AWBM) is one example that has been widely applied in the Australian context. However, the calibration of AWBM in a mining context can be challenging. Through a detailed case study, we outline an approach that was used to calibrate and validate AWBM at a mine site. Commencing with a data set of monitored dam levels, a mass balance approach was used to generate an observed run-off sequence. By incorporating a portion of this observed data set into the calibration routine, we achieved a closer fit between the observed versus simulated data set compared with the base case. We conclude by highlighting opportunities for future research to improve the calibration fit through improving the quality of the input data set. This will ultimately lead to better models for run-off prediction and thereby improve the accuracy of mine site water balances.CITATION:Kunz, N C and Woodley, A, 2013. Improving the accuracy of mine site water balances through improved estimation of run-off volumes, in Proceedings Water in Mining 2013 , pp 267-272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Q Zhou, J Pan, D Q. Zhu, C C. Yang

Oxidised pellets have become an indispensable high-quality charge for blast furnaces (BF) due to their uniform particle size, high iron grade, high mechanical strength, good metallurgical performance, as well as relatively low energy consumption and gaseous pollutant emissions in pellet production. Nevertheless, due to the rapid development of the global steel industry, highquality pellet feeds are becoming more and more scarce. In order to broaden the source of pellet feeds and reduce the production cost of pellets, more and more steel mills are going to use coarse iron ore fines with relatively low iron grade and low impurities for preparation of desirable pellet feeds through a typical wet grinding-settling-filtering process. In this work, the grinding, settling and filtering behaviour of Brazilian and Australian iron ore fines are studied and compared, aiming at finding out the internal relationship between the mineralogical characteristics of different iron ore types and their grinding-settling-filtering performance. The results show that the grindability is heavily dependent on the hardness of iron ores, which is governed by the mineralogical characteristics of the raw materials. Usually the higher the hardness, the more grinding energy is required. Except for Brazilian specularite, Australian hematite-goethite type iron ore fines and Brazilian hematite ore fines exhibit good grindability with a Bond Work Index of about 10–15 kW•h/t. In addition, the settling and filtering performance of ground iron ores are largely affected by the density, mineralogical characteristics of iron ore fines (eg, quantity of clay minerals and goethite and porosity of ore particles), grinding fineness, etc. Generally, iron ore fines with higher density, lower quantity of soft minerals (clay and goethite) and larger particle size give superior settling and filtering performance. For iron ore fines with inferior grinding, settling and filtering performance, applying more energy-efficient grinding techniques, blending with ore types with good settling and filtering performance can reduce grinding energy consumption and improve settling and filtration rates to maximise the productivity of equipment and lower the operational cost

Sep 18, 2023

By Toro HCH, Von Borries GH

A brief description of the semi-autogenous grinding (SAG;) facilities of Compania Minera Disputada de Las Condes is given. A data-logging and computer system was connected to the plant inter facing the existing analog control system in a supervisory s, control philosophy. The development of a control straiov,v t,) maintain maximum power of the SAG mill atsubjected to process restrictions is shownThe present control scheme is discussed inalgorithm was designed based on correlations onLween vartaoles. Associated with this, a direct level of control was developed be, on classical control algorithms, process inter-active tuning has been included. Also, an algorithm to prevent overloading of the is discussed. Control scheme tests are presented in comparison t manual operator control under the same conditions. It is shown t the control strategy gives a more stable operation and a higher plant throughput.

Jan 1, 1985

By C Li

Removal of gangue minerals from ilmenite concentrates can be accomplished by relatively low temperature roasting in controlled gas atmospheres to selectively enhance the magnetic separation characteristics of the ilmenite. At roasting temperatures below 800¦C the magnetising reactions are often not consistent with phase equilibria considerations. Metastable phases can nucleate and control the roasting products. In weathered ilmenites the phase assemblages and microstructures in the altered ilmenite grains can influence the roasting reactions. In this paper we give an overview of the phase chemistry of chemically weathered ilmenites and of metastable phases formed by low temperature roasting. We also report the results of roast experiments conducted in a neutral gas atmosphere. Major increases in magnetic properties after short roasting times at low temperatures were obtained for a range of ilmenite concentrates. For example heating a secondary ilmenite concentrate from Western Australia for 15 minutes in nitrogen at 600¦C gave an increase in the three kilogauss magnetic fraction from three to 92 wt per cent. The solid state phase changes accompanying the inert atmosphere roasts were characterised by combining elemental analyses with quantitative phase analyses of the ilmenite concentrates and their roast products. It was found that the phase reaction that is principally responsible for the increase in the magnetic properties of weathered ilmenites involves a transformation of disordered ferrous-containing pseudorutile to an ordered ilmenite-hematite solid solution containing typically ten to 35 mole per cent of the hematite component. Examples are given of the application of the inert atmosphere roast to effect separations of ilmenite from gangue minerals.

Jan 1, 2001

By G Baird, M Seto

A low-cost methodology that allows the determination of in situ stresses using oriented core specimens has been investigated. The technique can be used to determine the stresses during the early stages of a project, even in undeveloped areas of a mine. The research aim was to compare the experimental results estimated by the Acoustic Emission and Deformation Rate Analysis methods with those estimated by conventional Hollow Inclusion cell measurements. The studies have been focused on full stress tensor determination from a single oriented rock core. In all cases the rock core specimens recollected the in situ stresses reasonably well compared with the standard overcoring method.

Jan 1, 2000

By E Claridge

There are a number of major infrastructure tunnelling projects currently underway or proposed in New Zealand, including construction of new road and rail facilities and the refurbishment of existing road tunnels. These new projects have triggered a rethink of traditional practices in underground fire and life safety and local regulation.While there is a current surge in activity, tunnels have been a signifi cant part of New Zealand’s transport infrastructure for over a century. Despite this background, the new projects commonly face challenges that are symptoms of a national regulatory environment that has aspects that are inappropriate for underground environments. There are inconsistencies in local regional regulation and an absence of national guidance and standards relating to tunnel design. Historically, New Zealand has looked across the Tasman for guidance. Although recent overseas tunnel designs present learning opportunities, the adoption of international best practice and standards may not necessarily address local expectations or needs.This paper explores a number of specific matters affecting the design of road and rail tunnels in the New Zealand context, namely; the Building Regulations and associated local consenting processes and parties, and the responsibilities and needs of the New Zealand Fire Service.The discussion highlights the importance of a collaborative approach involving the designer, asset owner, regulators, emergency services, and other parties, and ensuring up-front clarity in design responsibility and ownership of residual risk.

Mar 8, 2011