Search Documents

The phosphatic overburden of Christmas Island is a lateritic soil and consists dominantly of crandallite and millisite. These minerals are polymorphs of general formula, (Na,K)x Ca2-x (Al, Fe)6 (PO4)4 (OH)10-x (2+x) H2O. Iron occurs only in millisite. Both minerals exhibit similar thermal transformations, dehydroxylating near 600¦C and recrystallizing above 800¦C. Dehydroxylation results in crystal structure collapse but retention of crystal morphology. Ggethite, boehmite and apatite are minor constituents of some-of the phosphatic Soils.

Jan 1, 1971

A series of numerical experiments were performed in order to define the fracture strength of schistose rock during crushing. Fracture strength was shown to decrease as the fabric aligned with the principal axis of loading. One of three types of characteristic stress-strain behaviour are defined by the orientation of the fabric with respect to the applied stress.

Jan 1, 1993

By G Gibson, B Bessen

In coal preparation, large dense medium cyclones (DMC) at low pressure heads (typically 9D where D = cyclone diameter) are the norm. This contrasts with high density mineral applications where, largely for historical reasons, smaller cyclones at high heads are the standard. There are advantages in preferring large diameter cyclones at low heads, assuming that metallurgical performance does not suffer significantly. These include simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, reduced medium pumping demands, smaller buildings and overall lower capital and operating costs. In 2008, therefore, Xstrata Zinc decided to trial a single DSM-design 800 mm cyclone in one of its four DMC lines at Mt Isa, replacing the four 400 mm cyclones previously installed. Circumstances allowed a low head of 9.5 D to be trialled, compared with the existing 400 mm head of 21.5 D. This paper describes the trial, including tests using painted ore particles as tracers, estimates of yield and metal recovery, and wear monitoring. The larger unit performed well. There was no evidence that metallurgical performance in terms of metal recovery and waste reject rate suffered, and there was some evidence that it may have improved. Cyclone life increased, and preliminary data suggest that the replacement cost of the 800 mm cyclones is less than half that of the 400 mm units, and this is expected to improve. The plant layout and operability have also improved significantly. Xstrata has therefore decided to convert the whole plant to four low head 800 mm units, replacing the original 16 high head 400 mm units. The paper includes an explanation of the effect of static head on DMC separating force. It also reviews earlier research on diamond applications, and applies a general DMC process model to the Xstrata case, both of which confirm that large, low head cyclones are appropriate in mineral applications, contrary to conventional practice. Such units could significantly reduce both the capital and operating costs of DMC plants in mineral applications.

Jan 1, 2009

By Clarke RG

Renison Mine was developed as the first all diesel mine in Australia. The foresight of the early planners in committing the Mine to Decline access has paid dividends in the past two decades with Renison Mine establishing itself as one of the most productive underground mines in the world. The excellent productivity has also resulted from the development of mining equipment technology, both on the part of the equipment suppliers and through the coordination of the Mining, Automotive and Technical Design Sections at Renison Mine. Constant improvements in truck and loader design, the design of specific equipment to carry out specialized tasks such as installation of services, scaling and ground support and the conversion to electrically powered equipment have been ongoing at Renison. Currently, larger scale trucks are being investigated for ore and waste haulage due to increased haulage distances and production requirements. It appears as though an articulated low profile truck of around 50 tonnes capacity may provide the short term solution based on the performance data available.

Jan 1, 1982

There are a number of factors affecting the discovery and develop- ment of uranium in Australia which makes this mineral almost unique and quite different from other minerals. I. The role of the Australian Government, which initially encouraged the discovery by offering rewards to prospectors who discovered deposits that could become economic. 2. At a later stage, the Commonwealth and South Australian Govern- ments prevented the development and production of "new mines" by refusing to grant mining title and refusing to allow sales of uranium by not issuing export permits. 3. The unique property that uranium and its daughter products possessed, i.e. radioactivity, meant that any person who purchased a geiger coun- ter could go prospecting, even though they had no previous experience in prospecting and they had an equal opportunity of discovering a new deposit as a company or independent geologist. 4. Because the exploration/demand for uranium didn't occur until the 1940s very little background geological information or models were available and so the early discoveries tended to become the locus for exploration rather than moving into areas which might on geological concepts lead to exploration programmes based on geological models. Because of the lack of knowledge there was the exchange of geologists from the U.S. Geological Survey and the South Australia Geologist Survey.

Jan 1, 1988

By Borshoff J, Coles R

The Rum Jungle Uranium Province is lo cated on the western margin of the Pine Creek Geosyncline approximately 60km south of Darwin. Uranium was discovered in the Embayment area (Whites Deposit) in 1949, spurring active ex- ploration and leading to the discovery of the Rum Jungle Creek South Deposit in 1959. With the discovery of the Alligator Rivers Uranium Field, new criteria in the understanding of the controls for mineralization sparked a re- surgence of exploration activities in the Rum Jungle area. Uranerz Australia Pty. Ltd. (UAL) commenced exploration in the area in the late 1970's in joint venture and in its own right. Two domal Archaean granitic complexes, the Rum Jungle and Waterhouse Complexes, domi- nate the area. They are unconformably mantled by Lower Proterozoic sediments metamorphosed to middle to upper greenschist grade. The Lower Proterozoic sediments are unconformably over- lain by remnant blocks of Carpentarian sand- stone, generally preserved in downfaulted blocks. Over a six year period extensive geolo- gical, geochemical and geophysical programs were conducted to reinvestigate previous target areas and locate new prospective zones. Exten- sive shallow bedrock drilling showed that lo- cally the stratigraphic succession is quite variable and cannot always be divided into an ordered succession for correlation with groups and formations established by the Bureau of Mineral Resources (BMR). Deformational events resulting in intraformational recumbent folding and overthrusting also account for repetition of certain lithotypes.

Jan 1, 1984

The underground mining of a narrow vein hard rock orebody is a capital and labour intensive method of extraction. Due to the nature of underground mining it is difficult for higher level managers to physically see the efficiencies and inefficiencies of a particular method. Extraction methods and sequencing often need to be altered from the original planned methods as a result of mine developent, providing more in depth information as it progresses. As a result of these issues contract mining of these orebodies is common practice. There are several types of contract structures for the purpose of underground contract mining with many complex permutations of them that reflect the different needs of each individual company and orebody. The different contracts are arranged dependent on the mining companyÆs desire to transfer or, alternatively, embrace risk. This presentation gives a brief overview on these different methods and their various advantages and limitations with regard to small scale and narrow vein underground mining. With respect to these different contracting methods, the presenter reviews the mutual growth benefits of emerging partnering opportunities, specifically with regard to smaller explorers exploring and developing prospective mining tenements. The specific advantages to small explorers include the resource flexibility and speed of project development that private mining contractors can provide. Given the contracting methods that are available, there is potential for small private mining companies to gain minor stakes in major projects and major stakes in medium sized projects by employing innovative contracting solutions to provide mutual benefits to the parties. Some potential scenarios to this effect are suggested in the presentation. This paper is available as a PowerPoint presentation only.

Jan 1, 2006

By Savage E. N

Two genetic types of base metal deposits occur in the Wainivesi area of central eastern Viti Levu. The Wainivesi deposit is now considered to be a stratiform volcanogenic type, and the Wailotu and Wainiviti deposits are described as contact metasomatic with some hydrothermal manifestations. The Wainivesi mineralization is correlated with the Tertiary "e" stage, i.e. uppermost Oligocene-Iowermost Miocene. Tertiary "e" stage rocks in Fiji are therefore potential ore producers of stratiform volcanogenic type. On the basis of plate tectonics with Fiji part of the New Hebrides Arc prior to rifting apart in the late Miocene, stratiform volcanogenic deposits of the Wainivesi type may also occur in rocks of comparable type and age in the New Hebrides.

Jan 1, 1976

By Weimin F

In the last decade, great strides have been made in the raise boring technique in China. Extensively, the drilling and blasting method has been replaced by the mechanized raising method since 1980. There are now over 3C raise drills operating in more than 20 mines. The diameters for shaft boring varies from 500mm to 2000mm, and to depths up to 90m. Tlis paper mainly describes the performance, mtLin technical achievments and applications of all four kinds of raise drills, and auxiliary equipment. Finally, some recommend- ations for future improvement in the raise boring technique are presented also.

Jan 1, 1987

Mineral exploration is the business of finding and defining ore deposits. Ore bodies are developed into mines and mines supply every mineral and metal upon which our society is built. Whether it be steel for our bridges, cement and aggregate for our concrete, coal for our power stations, copper for our wire, phosphate for our fertiliser or gold for our jewellery it first must he found, then mined and processed before we can use it. There is no other way.

Jan 1, 1993

By Bacigalupo-Rose

Simulations of complex physical phenomena, such as hurricanes and fluid flow around space vehicles, can now be effectively explored using modem visualisation techniques which have been developed to examine the results of numerical modelling using supercomputers. These techniques are also being applied extensively in medical investigations, including viewing the interior of the human brain. We have now applied these same techniques to the visualisation of gold deposits.Grade control in open pit gold mining operations may involve the collection of at least half a million samples in each mine. Extensive drilling programs also accompany the early reserve evaluation stages and exploration in advance of mining. Maximum utilisation of these very large amounts of information requires an ability to integrate, examine and present large three-dimensional data sets in order to be able to derive and effectively communicate information on grade distribution and geological controls.

Jan 1, 1993

The construction of mine headframes of reinforced concrete is not a new departure as many structures have been built of this, material particularly in Canada and South Africa. This type of construction has been satisfactorily tested in service and is now accepted by the mining fraternity.The two headframes at New Broken Hill Consolidated Limited are the first structures of this type to be built in Australia, and provide an interesting application of reinforced concrete design and construction.Reasons for Adoption of ConcreteDuring 1947 the writer visited D.S.A. and Canada and inspected three headframes, of reinforced concrete construction.Leading details are as follows:(i) Hollinger Gold Mines. (Timmins, Ontario) : Height of sheaves 110 ft. Shaft has provision for 4 skips each of 12,000 lb. capacity. Structure incorporates surface crushing plant.(ii) International Nickel Corporation-Murray Shaft (Sudbury): Height to sheaves 153 ft. 6 in. Shaft provides for 2-12 ton skips and 2 cages. Surface crushing plant built integrally with frame.(iii) Asbestos-Johns Manviae (Quebec): Height of sheaves 116 ft. Shaft provides for 2 skips 200 cu. ft.

Jan 1, 1956

By Wood CJ, Davis JJ, Askew H

A dynamic model of a dense medium circuit has been developed and tested against plant data. The model shows the response of the circuit to both controlled (changes in specific gravity set point or changes in circuit coal feed rate) and uncontrolled changes (changes in raw coal moisture, loss of raw coal feed) in operating conditions. The model is built up from dynamic models of the individual sumps, pumps, pipes, splitters, magnetic separators and automatic controllers in the circuit. The model can be used for design of automatic control loops and for investigation of possible process modifications such as changes in water addition points. This paper describes the model construction, the testing of the model against actual plant data and gives some examples of its use in investigating plant response to changes in operating conditions.

Jan 1, 1978

By Hinrichsen H. D, Rathburn D. R, Stieger W

The present situation in the field of iron ore pelletizing is briefly described with particular view of the Lurgi/Dravo travelling grate process. To meet todays pellet quality requirements with regard to physical and metal- lurgical properties it is often necessary to add basic fluxing materials. It has been de- monstrated that for certain ores, basic addi- tives provide a considerable improvement in fired pellet quality. The production of self- fluxing pellets is becoming increasingly attractive. One Lurgi/Dravo plant is now in operation and another is under construction which were designed for the production of self- fluxing pellets. Self-fluxing pellets may be considered as the primary or exclusive blast furnace burden and the installation of a sinter plant is not necessary if the pellet plant-can handle all in-plant fines. Reference is made to the first pellet plant utilizing iron ore concentrate, in-plant fines and basic flux. The use of solid fuel for pellet indura- tion is discussed because of the increasing prices and possible shortages of heavy oil and natural gas. Since there is a strong tendency to increasing plant capacities, the design fea- tures of travelling grate pelletizing plants for productions up to 6 million tonnes are Discussed.

Jan 1, 1974

By Wang SS, Frattaroll DR

In the development of novel sulfide collectors, especially for the low-lime and acid circuits, flotation of chalcopyrite, chalcocite, covellite and pyrite was studied with both new and commercially available S- containing collectors. The natural float- ability of sulfides, water quality, and redox potentials - all of which were considered im- portant in assessing collector strength and selectivity - were also investigated. Chalcopyrite exhibited the highest natural floatability. The response to most collectors, however, was chalcocite > covellite > chalcopyrite > pyrite. Water quality had a very significant effect on both natural and collector-aided floatability. De- ionized water and tap water had a flotation suppression effect compared with doubly- distilled water. Flotation results with single minerals are correlated with those for copper and pyrite from natural ores. Several novel collectors have now been developed for sulfide flotation in acid, neutral or mildly alkaline circuits. The results for four of these collectors, which have shown promise in commercial applications, are discussed in this paper.

Jan 1, 1986

By L Cooper, J Sharma, M J. Hendry

Thick clay tills below potash mine tailings and brine ponds are important natural barriers protecting fresh water aquifers in Saskatchewan. Centrifuge modelling was applied to assess geochemical processes and impacts of dilute brine (0.1 M NaCl) migration through clay till core samples obtained from non saline, unoxidised clay till at a mine site. At accelerated gravity of 876 + g, during each day of centrifuge modelling, flow driven through a 52 mm length core simulated transport through a 45 m thick clay over ~2100 years. Hydraulic conductivity, monitored continuously before and during brine permeation, was low and relatively constant (8.5 + 10-12 m/s), confirming that confining stresses prevent permeability increase. Core density and porosity measurements confirmed that reactive transport occurred under realistic in situ conditions. Breakthrough (defined by C/C0 = 0.5) of non-reactive Cl- occurred at 25 days. The slight delay for Na+ breakthrough, associated with small increases in Ca2+ and Mg2+ concentrations in the effluent were attributed to ion exchange, but carbonate reactions were relatively unimportant. Cation exchange analysis of core samples was inconclusive without corrections for porewater Na+ and carbonate dissolution. Geochemical processes that were observed during centrifuge modelling were successfully simulated using the 1D geochemical transport code PHREEQC. Solute transport was dominated by diffusion with limited ion exchange to delay Na+ migration. Brine would not break through a 45 m thick clay for tens of thousands of years. Based on these findings, the thick clay till at this site, if laterally extensive and undisturbed by drilling activity, is likely to act as an effective natural barrier to vertical brine migration over the long term.

Jan 1, 2003

By Irving R. C

THE objective of the iron smelter is naturally the production of high quality iron at the lowest practicable cost. To enable this, large tonnages are put through the blast furnace, and, at the same time, the quality of the iron must be under definite control.The modern blast furnace enables these objectives to be attained. The description whieh follows sets out the general details of construction of such furnaces, and the operation at thc Broken Hill Proprietary Company's blast furnaces at Newcastle, New South Wales.The occurence of iron in many forms is so well known as to need no description. Modern civilisation may be said to be built on a foundation of iron, and, today, the production of iron and steel has beeome one of the world's industries.A short historical introduction will serve to show the evolution of the processes and apparatus since iron production assumed importance.There is no definite date fixed as to when iron was first made, or by what means it was first discovered. Perhaps prehistoric man threw iron bearing stone on to his fire, and these became reduced, Ieaving a soft metal behind, or more probably the first iron was of meteoric origin.There is evidence, however, to prove that it has been known for a period of 6000 years. Iron has been found in the Pyramids and its use was known to the early Eqyptians and later to the Hebrews, Assyrians, Greeks and Chinese. Following the Greeks, the Romans excelled in its extraction and uses in the manufacture of their instruments of war, and to this fact can largely be attributed the success of their many wars of conquest. As the Romans overran the rest of the then known world they carried the art with...

Jan 1, 1930

This paper details successful implementation of a revolutionary pit access system involving excavation of an 'in-the-wall' ramp at Three Mile Hill open pit operated by Gold Mines of Coolgardie, formerly Goldfan Limited, at Coolgardie, Western Australia. Three Mile Hill is a medium-size, open pit, gold operation typified by hard, competent, fresh rock conditions from near surface. The project involved construction of a haulage tunnel or decline access located in the wall of an open pit in place of a conventional pit access ramp. Works undertaken as discussed herein included excavation, support, ventilation, dewatering, services installation, commissioning and monitoring. Prior to implementation, the conventional hardrock pit slopes and designs were constrained by the presence of infrastructure and a main road to the North and by adjoining leases to the Southeast. The combination of these factors and economic considerations resulted in a decision to proceed with an innovative in-the-wall ramp access system that is believed to be the first of its type in Australia. Back-analysis indicates that implementation resulted in a cost saving of as much as A$3.6 million and increased mineable pit reserves. The paper deals with the successful implementation and operation of the in-the-wall ramp haulage as well as an economic evaluation that is aimed at drawing some general conclusions on favourable conditions for implementation in other mining scenarios.

Jan 1, 1996

The grinding of ore to a size that is conducive to the extraction of minerals by leaching or flotation is an essential and expensive component of most mineral-processing operations. Overgrinding results in reduced flotability of the minerals, as well as problems in the filtration and thickening processes, while undergrinding leads to a product in which the minerals have not been exposed, and cannot be leached or floated effectively. Furthermore, coarse material causes settling in thickeners and agitator tanks. It is therefore essential, from the perspective of both operational and extraction efficiency, to grind the ore to an optimum size fraction. A well-run milling circuit will yield a product within a narrow size band and at a high throughput. Although the effective operation and control of milling circuits with their many operating parameters is widely acknowledged as a complex as well as a critically important operation, the benefits of such control are difficult to quantify. This is due to the difficulties in relating more stable operation to increased recovery of the valuable components in downstream processes.

Jan 1, 1993

By OÆBrien D. R

Up until June 1988, Mount Thorley Coal Handling and Preparation Plant disposed of tailings by two methods. Approximately half of the plant tailings was mechanically dewatered by solid bowl centrifuges mixed with plant reject and was subsequently disposed in mine overburden spoils; the remainder was pumped to tailings ponds. Both future mine planning and environmental constraints could not allow for the long term construction of more tailings ponds so, following evaluation of available dewatering technology, belt press filters were selected for the treatment of tailings in excess of the capacity of the existing solid bowl centrifuges. Commission of the four 2.5 metre wide belt press filters soon showed that marked differences in performance were experienced when treating different coal seams. Further analysis showed that the coal tailings from different seams were quite different in terms of clay mineralogy, and these differences could be correlated with varying degrees of filter performance. Poor filter performance was experienced with coal tailings rich in sodium montmorillinite clays. A number of variables were investigated including in-line mechanical mixing of flocculant and feed slurry, cation exchange reagents such as gypsum, and upstream addition of cationic flocculant. In order to achieve satisfactory performance on the worst tailings, a combination of all of the above was required. In this paper, the reasons for selection of belt press filters and the program of investigations and testwork required to arrive at satisfactory belt press filter performance for the treatment of troublesome bentonitic rich tailings are discussed.

Jan 1, 1989