Search Documents

By P Craig, M Holden, C Zhang, D Foster, J Oh, S Saydam, J Liu, H L. Ramandi, S Akdag

High stress in rock masses can cause significant instability problems such as squeezing deformation in soft rock and rock bursts in hard rock. The support system applied in burst-prone areas in high-stress conditions is required to be able to carry high load and accommodate large deformation of the rock mass without experiencing any serious damage. Yielding support systems are promising to provide support for both squeezing and burst-prone rock mass encountered in mining or tunnelling at depth. They are ideally strong and stiff initially and then ductile after yielding (Potvin and Hadjigeorgiou, 2020). With respect to support design, a ground support system has to create a safe working environment under both static and dynamic loading conditions by providing the functions of reinforcing, retaining, holding and connecting elements (Cai and Kasier, 2018). Rigid rock bolts and cable bolts perform reinforcing and holding functions of a ground support system. In highly fractured ground or with large excavation spans (eg at roadway intersections or in caverns), unstable ground depth can exceed the length of typical rigid rock bolts (ie greater than ~3.0 m). In such cases, flexible cable bolts are needed to tie the reinforced and retained rock mass back to deeper and more stable rock. The flexibility of cable bolts allows anchor lengths greater than the tunnel opening that would otherwise restrict rigid bolts. Cable bolts also offer higher strength to weight ratio, with tensile strengths 2–3 times that of standard rebar bolts. This high strength comes at the cost of lower strain tolerance, typically around 5–7 per cent at break. Despite the lower strain tolerance, cable bolts are often used as dynamic support in demanding burst-prone ground conditions. The lower strain tolerance is compensated by allowing sufficient free length for stretching or incorporating a yielding device. There are a number of dynamic cable bolts available on the market and a number of testing campaigns have been undertaken to quantify the dynamic performance of these cable bolts. This paper reviews the existing range of dynamic cable bolts and discusses the potential areas for improvement and further research.

Nov 29, 2022

By G Maude, R Ayres, R N McLean, N A. Reynolds

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Mabilo copper-gold-magnetite skarn deposit is located in southern Luzon in the Paracale mineral district, where iron has been produced historically from several skarn deposits. Mabilo occurs in the south-west of the district and is distinct and significant because of its high grades of copper and gold compared to historical mines.The Mabilo licence surrounds the Venida prospect, where past small-scale mining has exploited iron, copper and gold mineralisation in oxidised skarn. A ground magnetic survey in 2007 defined a number of strong anomalies under Quaternary volcanic cover south of Venida. The property was acquired by Sierra Mining Ltd in 2011, the magnetic data were remodelled and drilling commenced in September 2012. Diamond drill hole MDH001 targeted the strongest anomaly, which was 500 m south of Venida and under 20 m of volcanic cover. It intersected 94 m with an average grade of 2.2 per cent copper, 1.6 g/t gold and 36.6 per cent iron. Subsequent drilling was targeted by magnetic modelling, incorporating magnetic susceptibility data from drill core, which resulted in a high percentage of successful drill holes.The mineralised skarn preferentially replaces a dipping limestone unit within an Eocene sequence dominated by volcanic siltstone and sandstone, metamorphosed to marble and hornfels in the aureole of a Miocene quartz-diorite intrusion. Skarn occurs discontinuously along the eastern and southern diorite contact, controlled by primary sedimentary facies variation, structural geometry, fault offsets and intrusive contacts.Coarse magnetite skarn with garnet and minor wollastonite and clinopyroxene contains variably abundant chalcopyrite and minor molybdenite. Magnetite skarn occurs in sharp contact with unaltered marble or grades into garnet skarn with minor chalcopyrite. Structurally controlled retrograde skarn alteration is strong to intense and is characterised by bornite, clinozoisite, iron carbonate and chlorite. The retrograde skarn is weakly overprinted by late-stage pyrite veining and brecciation associated with clay-silica alteration with arsenopyrite and tetrahedrite-tennantite.The quartz-diorite stock is interpreted as the source of the prograde skarn-forming and mineralising fluids. Late-stage porphyritic intrusions in the contact zone indicate continuing magmatism during uplift, when telescoping led to a high-level, high-sulfidation overprint. This suggests the potential for deeper porphyry-style mineralisation.CITATION:Reynolds, N A, Ayres, R, McLean, R N and Maude, G, 2015. The Mabilo copper-gold-iron deposit – a new skarn discovery in the Philippines , in Proceedings PACRIM 2015 Congress, pp 431–438 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Optimising a mining or a quarrying operation about the overall cost is quite a challenge as there never is a situation where we have exactly the same conditions regarding rock properties, explosives' performance, mining equipment or evironmental restrictions. The amount of endless influencing parameters and variables make the evaluation process difficult. The enormous progress we have seen during the recent two decades in computing has however significantly increased our ability to evaluate and process the information gathered, and refine our existing prediction models. Refined models demand an increasing volume of good quality information to show reliable conformity with reality. There is a great need for co-operative work in the mining and quarrying society if we shall be able to screen all available data, systematically find the key-parameters influencing the results and to build robust scientific models. No organisations today have all the skilled people needed or can afford to hire the necessary specialists in all the overlapping branches. This paper highlights some on-going work where the Dyno Explosives Group is adding some new pieces to the giant jigsaw puzzle representing the ultimate model of the mining and quarrying operations we all of this society would like to see completed.

Jan 1, 1995

By K Vallo, T Haimi, J Pihlasalo, J Hamuyuni, M Lindgren, F Tesfaye

Decarbonisation of the steel industry has recently attracted a lot of research and technological development. Most of the technological developments are centred around the replacement of blast furnace (BF), which has been the main primary smelting furnace in the ironmaking step of steel production. Replacement of the BF is not an easy task because of BF’s many established capabilities over the years, especially its ability to use low-grade iron feed. In this regard, Metso has developed its own technology, Metso’s Outotec direct reduced iron (DRI) smelting furnace, to tackle this problem. The recently developed six-in line electric furnace for DRI smelting can be used for primary smelting of DRI from blast furnace grade iron ore. Unlike the electric arc furnace (EAF), the DRI smelting furnace can handle larger slag volumes that emanate from the high gangue in BF grade DRI. Therefore, fluxing plays an important role in operating the DRI smelting furnace. This paper presents fluxing options and proposes slag quality and operating windows for the DRI smelting furnace. Also, the effect of slag on refractory durability will be discussed.

Jun 19, 2024

By G McCullough, J Els, J Bassan

Integrated Remote Operations Centres (IROCs) have a crucial role in optimising a mine’s carbon emissions, especially as industry faces an imperative to achieve net-zero emissions on an accelerated timeline. To meet this time pressure, operations must adopt a comprehensive approach to energy-related carbon management and history has proven that modern technologies cannot be simply bolted into existing operations. An IROC is the most dependable solution to enable a swift transition from strategy to operational tactics that support carbon optimisation. Achieving net-zero emissions requires addressing significant energy management challenges such as fleet electrification, integration of renewable energy sources and large-scale energy storage. These challenges demand a profound change in planning, managing and executing work at large operations. The key to overcoming these challenges is an integrated approach incorporating collaborative decision-making across the value chain and more sophisticated planning approaches. Additionally, closer integration with downstream processing offers opportunities for carbon optimisation across the value chain. This includes the ability to supply tailored products that meet more varied feed-requirements of customers transitioning to less carbon-intensive processes and developing collaborative decision-making across the entire steelmaking value chain (by incorporating steelmakers, transport, coal/natural-gas/hydrogen supply, energy supply and iron-ore supply). However, this requires significant improvement in collaborative maturity and integrated decision-making capability. Finally, the imperative to reduce carbon emission demands the introduction of a range of new technologies into existing operations. The new technologies will increase the operational complexity of the mines and IROCs will need to evolve capabilities to manage the increase complexity and support the effective operationalisation and integration of these new mining technologies. This paper outlines the new capabilities required and the role of IROCs in effective integration across the demand value chain. The focus is on building on the mining industries’ existing IROC experience and augmenting with processes, technologies and lessons from other industries.

Sep 18, 2023

By S Tavelli

This discussion will present a case study in developing solutions to a metropolitan quarryÆs public relations, legal, environmental, and productivity problems. It details an extensive and detailed project to address the blasting practice in a medium sized quarry that is surrounded by residential and industrial zones. The principle work was done over four months duration during the normal production season. It included detailed drilling and blasting audits for baseline information. In addition, geologic characterisation, seismic modeling, correction of deviations from best practices, and implementation and monitoring of precise electronic timing to provide dramatic solutions for the quarry. The quarry is in the near suburbs of a large metropolitan city. It is framed on two sides by residential municipalities and on two sides by industrial zones. At the start of the project, the quarry was in court as a result of the lawsuit by one of the neighboring towns that was suing to close the quarry. The lawsuit had progressed to the advanced stage where in the Judge had appointed an arbitrator to make the decision of continued operation. This arbitrator was to observe our progress and recommend to the Judge the disposition of the case.

Jan 1, 2004

By R Goater, P Kirsch, S Goater, I Goater

With staff productivity and retention a crucial factor in the longevity of AustraliaÆs mining industry, some mining companies are increasing their focus on the health and well-being of their people, to minimise the risks of deteriorating health in an ageing workforce. Many of AustraliaÆs mining operations rely heavily on long distance commuter (LDC) rosters, which are argued to have a significant impact upon worker health, wellbeing and lifestyle choices. The potential impact of workforce health on mine safety performance, efficiency and operating practice is an interesting additional line of enquiry. Food choice, exercise and recreation initiatives offer living and working conditions that æempower healthy choicesÆ in the shift worker community, but do not guarantee improved worker wellbeing. This paper explores first-hand the experiences of one individual over two and a half years of employment at different mine sites, under different shift conditions and across different operating crews. Novel insights and recommendations concerning the LDC lifestyle are offered through integrating reflections on one individualÆs fly-in, fly-out (FIFO) experiences in open pit mining operations from personal, family, professional and academic perspectives.CITATION:Goater, S, Goater, R, Goater, I and Kirsch, P, 2012. This life of mine - Personal reflections on the well-being of the contracted fly-in, fly-out workforce, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 31-40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By J Evans-Wheeler

"The mandate of the 2005 VALMIN Code to provide ‘(all) reliable, thorough, understandable material information required by investors and their advisers when making investment decisions’ requires that due diligence for tenure be full and thorough. Yet a published due diligence would often appear to be simply a list of tenures allegedly held without any commitment as to the standing of the tenure as safe and secure or otherwise.The value of due diligence for tenure, as mandated in the 2012 JORC Code and the 2005 VALMIN Code, must focus on compliance rather than simply on ‘vital statistics’. Enforcement in every jurisdiction in Australia focuses on penalties (some more harsh than others) for non-compliance, which, in turn and most importantly, reflects directly on security of tenure. Some 22 Acts (on average) impinge on security of tenure and fundamentally underpin the security of any mineral asset.This paper will outline regulatory processes to demonstrate how tenure compliance is achieved and argue that the rigorous application of good practices in tenure evaluation will lead to more of this information being made available on a regular basis.The paper will then focus on further practical examples of tenure compliance failures, the application of these to the requirements of the JORC and VALMIN Codes and due diligence that failed to fulfil the mandate. Examples will be given that alerted other professionals using the JORC Code to complex geological and mining situations of which they were unaware in their valuations.Finally, the author will make a personal plea for tenure to be considered at the commencement of any reporting process.CITATION:Evans-Wheeler, J, 2016. The VALMIN code and tenure compliance – not just a list, in Proceedings Project Evaluation 2016, pp 112–121 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By A Guillen, J-P ChilFs

Most 3D geological modelling tools were designed for the needs of the oil industry or detailed mine planning and are not suited to the variety of situations encountered in other application domains. Moreover, the usual modelling tools are not able to quantify the uncertainty of the geometric models generated. The potential field method was designed to build 3D geological models from data available in geology and mineral exploration, namely the geological map and a digital terrain model (DTM), structural data, borehole data and interpretations of the geologist. This method considers a geological interface as a particular isosurface of a scalar field defined in the 3D space, called a potential field. The interpolation of that field, based on cokriging, provides surfaces that honour all the data. The 3D model and its parts are always consistent with the observations. New developments allow the covariance of the potential field to be identified from the structural data. This makes it possible to associate sensible cokriging standard deviations to the potential field estimates and to express the uncertainty of the geometric model. It also, for the first time, gives a statistically optimal, geologically sound way of interpolating geology, other than directly joining the dots as you do with CAD. Practical implementation issues for producing 3D geological models are presented: how to handle faults, how to honour borehole ends, how to take relationships between several interfaces into account, how to model thin beds over many kilometres, how to optimise lithological properties and how to integrate gravimetric and magnetic data. We describe all geology surfaces and volumes using implicit functions. These are then rendered onto the required sections, plans, etc. The estimation of orebody grades and tonnes, using an unbiased and optimal geostatistical technique, makes use of the stratigraphically bound 3D geology model. An application to the geological modelling of the Hamersley iron ore district, Australia, is briefly presented.

Jan 1, 2009

By M Recabarren, A Echeverria, J Ronda, J I. Guzman, R Dodds, G Juarez, E Vila-Echague

A strategic mine plan is a fundamental part of any mining operation. It must provide a realistic and operative extraction and processing schedule, and yield the highest value for the business. For open pit mines, the problem can be modelled as a set of blocks representing the deposit, for each of which we need to decide if it is going to be mined, if so, when and where it will be sent (process, stock or dump).This problem can be proven to be of NP-Hard complexity. The traditional approach used by mining engineers to tackle this complexity is to separate the problem into more tractable components, solving each separately. The first step is to use the Lerchs-Grossman (LG) algorithm to obtain the final pit limit, as well as a set of optimised pit shells (nested pits), using different input prices. Then, using this input, operational phases are designed. Third, the set of phases can be used as an input for a phase-bench style optimisation, usually using a mathematical programming-based algorithm.There are, however, several problems with this approach. First, dividing the problem into simpler parts has the consequence that any compromises made at early stages limit the potential value left for the following steps. Second, LG is a static algorithm, with no concept of the time-value of money, capacity limits, opportunity costs, etc. Phase design is essentially a manual step, for which nested pits provide insufficient information in practice, and therefore the quality of the result in terms of potential net present value (NPV) depends strongly on the experience and expertise of the designer. This means that key input data such as commodity prices, different processes capacities and mine movement limits, are considered only at scheduling, when there is little room for optimisation. This sequential approach limits the potential value in each step, where a simplified problem is addressed, instead of addressing the real, and more complex problem, which is dynamic and should be solved as a whole.We present in this paper an algorithm, and its commercial software implementation, that addresses the dynamic problem as a whole, simultaneously and automatically creating a high-value strategic mine plan that adheres to basic operational constraints, determining dynamic cut-off grades and delivering a set of phases which can serve as a much stronger guide than nested pits for the final design. We discuss some of the key elements of the algorithm and propose a new methodology for strategic mine planning, where phase design dynamically responds to mining strategy definition. Results using different mining and operational parameters on a fictitious copper deposit are used as a demonstrative example.CITATION:Juarez, G, Dodds, R, Echeverria, A, Guzman, J I, Recabarren, M, Ronda, J and Vila-Echague, E, 2014. Open pit strategic mine planning with automatic phase generation, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 147–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By R Araya, G Harbort, D R. Seaman, L Huynh, P D. Munro

In today’s operating environment many conventional cleaner circuits struggle to produce final grade concentrate with acceptable levels of non-sulfide gangue and/or penalty elements. This is primarily due to poor selectivity and the entrainment of gangue, and is further exacerbated by the processing of lower grade ores with more complex mineralogy that require finer grinding for liberation. In new concentrators, the standard approach to cleaner circuit design is to define the number of stages of mechanical cells required to achieve the desired concentrate grade. Residence time is the primary factor to size cells and to determine the number of cells required to attain target recovery. While it is required for recovery, a bank of mechanical cells is not the ideal solution to maximise concentrate grade. Relatively coarse bubble size means slow flotation of fines, requiring long residence times. The combination of long residence times and no froth washing means higher entrainment as the pulp becomes more barren and froth stability decreases down a bank.In recent years, the Jameson Cell technology has been retrofitted into a number of concentrators around the world to solve both cleaner circuit capacity and concentrate grade issues. Jameson Cells have been installed at the head of conventional cleaner circuits to produce final grade concentrate in a single step of flotation using a single cell (referred to here as ‘cleaner scalping’ duty). The experience gained from these installations has provided the platform for the design of improved and simpler cleaner circuits that will perform better and be more robust to operate. This paper analyses traditional cleaner circuit designs and explains the philosophy behind new hybrid cleaner circuits, which use Jameson Cells to produce final concentrate and mechanical cells for a ‘cleaner scavenger’ duty. The advantages of the new cleaner circuit design are demonstrated by a case study from an operating plant. Engineering studies show that the better metallurgical performance can be achieved with less equipment than conventional cleaning designs, reducing capital cost, operating cost, and with more than 30 per cent energy savings.Finally, the paper describes simple modifications to the standard laboratory flotation test procedures which accurately simulate this new cleaner circuit using routine equipment.CITATION:Huynh, L, Araya, R, Seaman, D R, Harbort, G and Munro, P D, 2014. Improved cleaner circuit design for better performance using the Jameson Cell, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 141–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M Allen

Energetics has been in the business of climate change for more than twenty years. This experience has only served to cement the understanding that decisions taken during design define the environmental and economic performance of any project. The 80-20 rule definitely applies, with 80% of a project’s performance being set through the first 20% of design decisions. This in depth knowledge is used for determining energy price forecasts, future carbon markets and carbon costs, current and future energy technologies, as well as giving a thorough understanding of the processes and technologies in place in the mining industry to work out what the most carbon and energy sensitive decisions during design are. Project selection and design is a gated process where decisions are taken in line with the information available at that point in the evolution of the project. Design decisions are, by their nature, dominated by uncertainty. In order to ensure that robust decisions are taken, it is necessary to ensure that the correct information is brought to bear at the correct decision point. This then defines and supplies the necessary carbon and energy information for design decisions to be correctly made. One of the most significant risks facing design engineers and decision makers in the mining industry is the future cost of energy. Part of this risk is associated with a future cost of carbon, however, a significant part of this risk is the cost, and variability in this cost, of the energy itself. This paper investigates the information required to support good decision taking during the design process.Project Managers and MetPlant Operators accept poor quality evaluations because they are generally unaware of what they should expect.The 2010 draft AusIMM ‘Guidelines for Techno-Economic Evaluations’ were collated by a subcommittee of practitioners and are regarded as best practice.They apply directly to projects and metallurgical plant evaluations, including those with a heavy technical basis. They can be applied to technical problem solving where there are no monetary computations.Project Managers and MetPlant Operators should demand that economic models and evaluations follow the six principles. They should become working tools which are easy to understand, fit for purpose, consistent, rigorous, record sources of input data, have key graphs and are rapid to audit.

Aug 8, 2011

By C Tapia, B Hay

There is a close relationship between the mining industry, economic growth, and technological and social development. Mining activities benefit all economic agents, but only during a timespan determined by available reserves, primarily driven by internal factors such as production rate, technology and costs, and external factors such as prices determined by the market and taxes and royalties controlled by governments (Gordon and Tilton, 2008; Henckens, 2021; Tapia Cortez et al, 2018). The intense use of Mineral Commodities (MC) needed to maintain the current lifestyle has placed ore depletion as one of the main threats to sustainable economic, social and technological development. However, ore depletion does not only arise due to the finite nature of MC, price fluctuations or technological challenges. It is also triggered by the ‘economic limits of extraction’, determined by the optimisation of financial factors and technical restrictions within the regulatory framework (Henckens, 2021). Most reporting standards – if not all – define ore reserves as ‘the economically mineable part of a Measured and/or Indicated Mineral Resources’ determined by the technical and economic viability of extracting, processing and commercialising MC having the NPV as the fundamental decision – making tool (JORC, 2012; Krzemień et al, 2016). However, is the NVP an ‘economically’ basis index able to capture the complexity of economic phenomena? No, it is not, and it is crucial to define what is economic and financial. Although related, they are different disciplines. Economics studies the behaviour of the different market agents, including human behaviour and policies and explains the factors involved in the scarcity (or surplus) of goods and services. Finance focuses on financial systems and managing funds considering the time, cash available, and risk. It involves banks, loans, investments, and savings and can be considered a small subset of economics (Simon, 1959; Tapia Cortez et al, 2018). Given the economic nature of ore Reserves, endorsed by governments (Figure 1), NPV is an incomplete tool to determine ore Reserves as it limits the problem to simply maximising cash flows instead of optimising the economic benefits for all economic agents. In addition, using the rigid scheme of controlling taxation – unable to adapt to new market or economic conditions and systematically increasing – within the NPV framework only increases the sub-optimisation of ore reserves, mainly due to the systematic taxation rise. Short-term benefits of higher taxes and royalties are unlikely to offset the impacts of reducing exploration and project development in the long-term, which not only boosts ore depletion concerns but also reduces competitiveness, threatening economic and social welfare (Fisher, Cootner and Baily, 1972; Gordon, Bertram and Graedel, 2007; Lilford, 2017; Mardones, Silva and Martínez, 1985; Radetzki, 2009; Rodrik, 1982; Tan, 1987; World Bank, 2000). Holistic methods and collaborative tools, able to dynamically simulate and assess how changes in the technical settings, regulatory framework (taxes and royalties), and financial factors affect the availability of ore reserves and the impact for all economic agents, should be incorporated into the evaluation process to fill the gap.

Aug 2, 2023

By H Lemos, E Nunes, D Jacobson, R Costa, L Ono, A Alves, H Delboni Jr

Oversize rock breaking and metal tramp removal are key issues for reducing primary crusher downtime, as well as improving the safety associated with its operation. Remote operation of such tasks would thus not only increase productivity, but also reduce the risks related to work in confined spaces, fall risks, and overhead hazards. These issues are particularly relevant in high-capacity operations such as iron ore mining, where large machines are in continuous operation. This article describes the architecture, construction and advanced testing of a novel remotely operated robotic mechanism for assessment and removal of metal tramp from primary crusher chambers. The system essentially includes a robotic-arm equipped with a hydraulic clamp tool for handling oversize material, as well as an oxy-flame module for cutting metal pieces entrapped within the primary crusher cavity. The first industrial unit was delivered to a large iron ore mine in Brazil, where the installation and testing is scheduled within the coming months.

Nov 8, 2021

The key issue which determines the use of imaging for explosives and mining research is the question - `What information will I gain by using imaging technology?' This paper will address that question from the point of view of a researcher and cameraman working in industrial imaging and photography. The paper will establish a common set of reference standards for high speed imaging and photography which researchers can apply when deciding which type of imaging technology is appropriate. It will present an overview of current image analysis technologies and practices in use across a range of appropriate scientific fields and draw lines of commonality of approach between these fields and the field of explosives and mining analysis and research. Further to this, the paper will examine the different technologies from an image quality reference point, ease of operation, cost, and reliability parameters. Finally this paper will present an argument for the hybridisation of established and new technologies which could provide a more beneficial approach to the use of imaging as a tool of research and analysis in the explosives and mining industries. This will include a novel approach to high speed filming and analysis in the field which should deliver high quality images in a time frame which is more appropriate to urgent action and solutions.

Jan 1, 1995

By J A. de la Torre, I R. Cerna, G K. Karadjian

The La Colorada underground mine in Zacatecas, Mexico is a mechanised cut-and-fill silver mine with a capacity of 1250 t/d. The project focused on training the mine’s experienced operators for a fleet of underground trucks, through the use of a training simulator. The project was run by the simulator vendor, in collaboration with the mine’s maintenance, safety and production management.A training program was created targeting maintenance reduction, productivity improvement and increased utilisation and availability. Operators were first acclimatised to the simulated environment, had their current performance baselined, then received targeted coaching, with the process repeated to reinforce learnings. Concurrently, production, maintenance, and safety data was being measured in the real world to measure skills transfer. Due to limited telemetry available from the equipment, many of the data points for the project were sourced from maintenance logs, and accounting data.Equipment failure data measured from unscheduled maintenance records showed an overall 6.5 per cent decrease in unscheduled maintenance following the implementation of the training program. This rate of reduction correlated with the significant decrease in equipment abuse behaviours measured within the simulator during this period. Additionally, overall maintenance activities showed a significant decrease, confirming that reductions in unscheduled maintenance were not achieved through increases in scheduled maintenance. The reduction in equipment damage also increased availability and utilisation of the truck fleet. This highlights that the maintenance improvements not only reduced maintenance costs, but made the fleet available for more production. Moreover, the variability of the operator performance was decreased by 86 per cent, and the difference between their best operator and the worst is less than the baseline; this showed a gap where machine abuse, productivity and cost are impacted directly.This project illustrated that even small-scale mining operations with an experienced operator workforce can achieve positive return on investment (ROI) from simulation-based training. It also highlights that in the absence of equipment telemetry, alternative data sources such as accounting data and maintenance logs can be used to quantify ROI from training.CITATION:Karadjian, G K, de la Torre, J A and Cerna, I R, 2017. Innovations in underground hard rock operator efficiency – through simulation-based training technologies and processes, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 53–58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By D Lucato, B Haase, R Saha, S Limberger-Forte, J Lishman

Cadia East Mining operations have employed geometallurgical techniques to advance the understanding of the in situ rock hardness variability across existing Panel Caves (PC). Geometallurgy advances the understanding of variability across an orebody through the integration of geology, mineralogy and processing response and therefore enhances spatial mapping of comminution or separation properties. Spatially extensive geometallurgical measurements are necessary so that continuous rock properties can be generated and used for the development of comminution and processing domains using geostatistical modelling. Standard testing protocol across geological and mineralogical domains is vital to understand the variability in deposit wide comminution and separation properties. The high cost and large sample requirements associated with metallurgical test work typically results in insufficient data density and distribution, making it difficult to model and map deposit scale variability. Quantitative hardness proxy tools are useful to measure in situ rock hardness, however this data is typically either sparse or missing within advanced mining operations. In recent years, mineralogy and multi-element assay data has often been collected as part of the standard geological data set and is generally coincident with metallurgical test work. In this paper relationships between mineralogy and comminution parameters have been applied to multi-element assay data with coincident measured Bond Work Index (BWi) data to generate a predicted BWi using linear regression. The predicted BWi is intended to supplement existing measured BWi data to enable better extrapolation across the deposit. Geostatistical Conditional Simulation methods have then used the predicted and measured BWi data to produce a BWi variable as a new input to the resource model. The simulated BWi can be used as an input for specific energy models to predict required grinding energy consumption across a deposit.

Mar 22, 2022

By P Cherepanskiy, G Elphick, R Hus, C Perring

When an iron orebody nears its end of life, the extracted material can become increasingly problematic to handle. Higher moisture content occurs as larger portions of originally-below-water-table material is mined, which in some deposits is accompanied by further changes in physical and/or chemical properties present along the edges of the orebody. Plant delays related to problematic material have affected all of BHP’s mining hubs to various degrees. Following the recent successful work in Yandi, where the development of an index to quantify the handleability of channel iron ore deposits resulted in an increase in extracted volumes and an extension to the expected life-of-mine, the value of implementing similar indices for bedrock iron ore deposits has been recognised. A materials handling index has been developed by combining observed empirical relationships between material properties and processing plant performance. Indices for each deposit were further refined and optimised by implementing a back-testing strategy which facilitated an understanding of what weighting or scaling each of the contributing components should carry to yield the highest success rate of predicting actual delays at a given plant. Currently materials handling indices are deployed to all mine sites and are made available in block models as well as calculated for individual blasthole and production samples. Values in block models are obtained by predicting the required properties using machine learning models, whereas hyperspectral data is used to ‘measure’ some of those properties on a sample level. This paper discusses the work that has been undertaken to obtain materials handling indices, the testing that has been done to optimise them, and what processes have been developed to ensure the best metrics are being used in the different planning and scheduling horizons to optimise extraction.

Jun 22, 2022

By G Lane

This paper discusses the factors that contribute to the cost effective design of a concentrator. Concentrator design and layout outcomes are functions of the team (engineer’s and owner’s) participating in each particular project. The benchmark for relatively modest projects was set in the 1980s and 1990s during the ‘gold boom’ when numerous cost effective plants were designed and constructed on a lump sum basis in a very competitive market. A number of factors contribute to lack of transference of the lessons learnt in gold plant design to concentrator design including established paradigms in the design and layout of concentrators, lack of experience in cost effective design, operator’s preferences for flowsheet and layout and simple lack of appreciation of the impact of plant footprint on materials quantities and resultant capital costs.Experiences with recent copper concentrator projects (both small and large) are used as case studies.

Aug 8, 2011

In todayÆs evolving and globalised world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to æengageÆ communities and measure the success of these engagements without a clear understanding of æhowÆ to do this. This move, away from compliance, develops more of a focus on sustainability and æcommunityÆ social responsibility rather than corporate social responsibility. This shift leads to the development of world-class projects that provide sustainable development for people, reduce the incidence of costly delays, and promote good global citizenship for companies. The process of æengagingÆ communities in mining project design and development leads to sustainable development, a stronger license to operate, and a reduction in social and political risk. To create this mutually beneficial relationship between communities and companies, communities must be æengagedÆ in the project development and risk assessment processes as early as possible, preferably during the exploration or the concept phases. How to create this æengagementÆ and manage this risk will be discussed.

Jan 1, 2007