Search Documents

By N Johansson, D Johansson, A Beyglou, H Schunnesson

As demand for optimisation of mining processes increases, more attention is drawn to blast performance and fragmentation improvement. Fractures and discontinuities are among the most influential factors in blast results, therefore one of the initial steps towards blast optimisation is to gather information about the rock mass and integrate it in blast design. This paper presents a method for assessment of rock mass discontinuities and integrating it in production blasts in the Aitik open pit copper mine in Sweden.3D photogrammetric techniques were utilised to map discontinuities and distinguish domains of similar geologic structures in the pit. As a pilot study for a future campaign, four different initiation directions were tested through six pilot blasts in one of the domains. The results were compared in terms of swell and loading efficiency of rope shovels to identify the correlation between blast performance and initiation direction compared to major discontinuity families.It was established that in the trial domain, blasts initiated towards north or north-west yielded larger swell and better performance of loading. Comparing these blasts with discontinuity families show that there is a correlation between blast performance and initiation direction according to the dip and strike of these discontinuities. Such knowledge can be used for future blasts in the same domain to increase long-term operational efficiency through slight modifications in drill pattern and initiation design.CITATION:Beyglou, A, Schunnesson, H, Johansson, D and Johansson, N, 2015. Adjusting initiation direction to domains of rock mass discontinuities in Aitik open pit mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P Micale

Geological data provides the foundations for the mining value chain. It is used to underpin the modelling and planning and consequently optimise downstream business decisions. However, it is often forgotten or taken for granted. End users often assume the data to be sound without verification. Geological data can be considered a company’s number one asset. Subsequently, the storage, use and management of this data need careful curation and time invested in preserving and protecting it. An established polymetallic mine with 20 000 drill holes could have a data replacement value in excess of $500M at 2020 prices, excluding labour and salary costs. The Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the ‘JORC Code’) provides guidelines for Public Reporting. Within the code, Table 1 requires discussion around the different types of geological data, its collection and use. What is needed is additional details regarding the validation and integrity of the geological database. A comprehensive guideline specifying minimum geological standards for geological databases has been developed. This expands on the critical points outlined in Table 1 of the JORC Code. This guideline can be used by companies where geological databases are managed in-house or used to assess these services’ outsourcing. This guideline will ensure that geological data is reliable and unadulterated and can be used with confidence. Using this guideline will assist in preserving the investment of geological data in the mining value chain

Mar 22, 2022

By S Mitra, D O’Dea, N Barrett, S, T Honey, M M. Hoque

The steel industry is currently exploring hydrogen-enriched blast furnace operations as a means to reduce the greenhouse gas emissions. However, there is a need to investigate the gas permeability behaviour of mixed burdens comprising of lump and sinter as the current knowledge regarding their behaviour is limited, particularly with regards to hydrogen enrichment. In the present study, a series of interrupted softening and melting (S&M) under load tests were carried out in a hydrogen rich gas environment (~15 per cent) in the temperature range from 1000 to 1300°C by placing different types of ferrous ore layer including Newman Blend Lump (NBLL), sinter and sinter-NBLL mixed burden in between two coke layers. X-ray computed tomography (CT) was then used to scan the interrupted test samples. Scanned images were first analysed using an image processing workflow implemented in ImageJ and the material simulator GeoDict (v2022) to segment different phases such as coke, ferrous and void based on their grey scale values. A quantitative analysis was then performed on the segmented images to estimate the phase volume fraction as well as bed permeability. Bed void fraction thus obtained agreed well with the bed contraction data obtained from the S&M test. It was further noted that both ferrous layer void fraction and bed permeability decreased linearly with increasing temperature for all ore samples. The mixed burden voidage changed in a similar fashion to the sinter, demonstrating a high temperature interaction between the two materials

Sep 18, 2023

By S Rogers, D Stead, E Eberhardt

The last decade has seen a major increase in use of the discrete fracture network (DFN) approach applied to cave mining problems, often integrated within more complex geomechanical simulations. Because the value of the DFN model directly depends on the quality and quantity of available field data, there is the need to apply dedicated mapping procedures to collect sufficient structural data at the required engineering scale. This paper attempts to address several key questions about DFN modelling; for example: are current methods for fracture mapping suitable for DFN modelling? What are the critical parameters that we need to measure and what do we need to change in the current practice? Particularly at the earlier stages of a cave project, engineers may have to account for the lack of appropriate data, which manifests itself in the form of increased uncertainty and the difficulty to characterise variability in an objective manner using a limited set of data. DFN models could in principle be generated using limited data by assuming statistical distributions for the sampled parameters; however, engineers would need to be aware of the implications that such limited knowledge (and increased uncertainty) would have on stability analysis, fragmentation analysis and mine design. When used correctly, a DFN approach offers practitioners the opportunity to:maximise the use of fracture data collected from mapping of rock exposuresgenerate more realistic synthetic rock mass modelsprovide estimates of natural fragmentation that also account for rock mass variability.CITATION:Elmo, D, Eberhardt, E, Stead, D and Rogers, S, 2016. Discrete fracture network modelling – importance of accounting for data uncertainty and variability, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 845–852 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J J. L du Plessis, S Viviers, G Ratner

Escalating electricity costs are one of the biggest operational cost drivers in mining. The trend to use high-powered auxiliary fans delivering increased airflow to meet the dilution requirements of diesel equipment, together with the reliance on ducted systems rather than traditional flow-through systems to ventilate areas, increases the overall energy requirements of ventilation systems. To manage and reduce electricity costs energy management systems can be implemented, inefficient operating units can be replaced and the operation of energy-consuming components of ventilation systems can be optimised.This paper describes the process followed to design and develop an energy-efficient axial flow auxiliary fan. The fan-targeted design was based on static pressure and volume flow rate requirements incorporating higher overall fan efficiencies. A brief overview of the results is given, including the aerodynamic design procedure using computational fluid dynamic (CFD) analysis. The mechanical design criteria used, including stress analysis on the rotor and designs to improve the vibration levels of the fan, are also presented. Through this study it was demonstrated that the aerodynamically designed rotors using profiled and twisted blades improve the total fan efficiency considerably when compared with some of the older-generation fans using cambered plates. The latter were typical in the mining sector in South Africa at the time of the study where average overall fan efficiencies of standard cambered fans less than 63 per cent and some of the older-generation cast aluminium blades have peak overall fan efficiencies of about 65 per cent. Peak overall fan efficiency of more than 80 per cent was achieved by using the described design and development process. Additional benefits are that the fans are quieter due to the better aerodynamic design and have a longer operating life due to reduced vibration levels.In conclusion, the use of CFD to develop fans to deliver the required volume flow at the required pressure allows quicker design turnaround time. It furthermore allows the ventilation engineer the option to specify a specific fan and is not limited to an off-the-shelf catalogue fan. It thus allows engineers to purchase a fit-for-purpose energy-efficient fan. The introduction of reliable fan control systems may, however, still result in the biggest cost benefit for underground mines.CITATION:du Plessis, J J L, Ratner, G and Viviers, S, 2015. Design and development of energy-efficient secondary axial flow fans, in Proceedings The Australian Mine Ventilation Conference, pp 337–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By T B. T Nguyen, L Matthews, D O’Dea, T Honeyands, T Harvey

Productivity and fuel consumption of the blast furnace is driven by the quality of the iron ore sinter, which in turn is related to the sinter mineralogy. The sintering conditions including temperature and gas composition have a significant influence on the formation of melt and finally the mineralogy of the sinter. In this work, analogue sinter tablets were produced from iron ore fines in a laboratory furnace with tightly controlled temperature profile and oxygen partial pressure in the gas. The mineralogy of the sinters was analysed using reflected light microscopy. The results showed that increasing thermal enclosed area (area enclosed by heating and cooling curve above a reference temperature) reduces primary hematite and platy silico-ferrite of calcium and aluminium (SFCA) contents. This is attributed to increasing melt formation, leading to greater assimilation of the iron ore particles. Lower magnetite was found for tablets with greater median pore size, which is thought to be due to greater oxidation of magnetite to hematite during cooling in air. It was also found that higher alumina content was found to result in more SFCA formation under the same heating/cooling conditions, whereas tablets with higher goethite had higher assimilation and produced more secondary hematite on cooling. Finally, it is necessary to relate the enclosed area to the temperature at which the melt formation becomes significant which strongly depends on chemical composition of the ore studied.

Nov 8, 2021

By R Hartner

Digital optical microscopy (DOM) and automated SEM-based (ASEM) mineralogy systems (MLA, QEMSCAN) have experienced significant developments within the last decade. However these developments have been independent from each other and the two mineralogical techniques have so far not yet been integrated to combine the strengths and technical benefits of both analytical platforms. This detailed comprehensive mineralogical information is critical support for geometallurgy.Major hardware and software advances in DOM in the last few years have provided important new capabilities with potential applications to automated mineralogy. These technological advances have been largely driven by sectors outside mining (eg medical pathology) and have not yet been widely adopted within the minerals industry. The advent of DOM offers significantly more automated mineralogy capabilities than traditional expert-mineralogist driven optical microscopy. This is based on advances in automated image acquisition, high resolution cameras for digital imaging, imaging of large areas through mosaic options, integration of multiple layers and application of advanced image analysis techniques.Ongoing research involves combining the outputs of DOM and ASEM-based microscopy to create new capabilities for integrated microscopy based on development of advanced cross-platform image fusion and data integration between DOM and ASEM (exploiting the benefits of both analytical platforms). This requires non-linear image registration and transfer of mineralogical identification from ASEM to DOM systems using sophisticated image manipulation and data analysis software.Examples will be given of image fusion and data registration for a range of different ore types. Image fusion techniques are demonstrated using a porphyry copper deposit sample where sulfides and precious metals are classified using the MLA and gangue mineralogy obtained from DOM images. Data integration enables creation of a library containing optical property variability information for minerals identified by the MLA; thus reducing the reliance on skilled mineral identification by supplementing human interpretation

Sep 5, 2011

Froth flotation is widely used for the separation of particulate materials in the world. It is a complex process whose operational behaviour in process plants is difficult to predict. A comprehensive phenomenological dynamic flotation model was presented at the 1982 IMPC. This model uniquely linked the particle/bubble interactions and water transport phenomena to the flotation cell hydrodynamics. The model was used as a dynamic framework to analyse and develop process optimisation strategies. New developments in mineralogical characterisation, real time information management systems and data validation simplify the implementation of flotation technologies for mine to mill grade recovery optimisation. With recent developments in software programming, dynamic simulation enables process engineers to develop process alternatives interactively. This paper presents such an implementation of current process analysis tools and an updated froth flotation dynamic model. It demonstrates how this new environment can be used to improve our technological knowledge of flotation, eg alternative bubble/particle attachment and detachment microprocesses can be incorporated. The dynamic flotation model has several manipulated variables (such as feed flow rate, per cent solids, aeration, wash water flow rate, frother flow rate, specific power energy (impeller speed/delta pressure), cell geometry and tails flow rate) and evaluates the dynamic effects of these variables on grade and recovery.

Jan 1, 2005

By J E. Moffatt, N A. Spooner, T J. de Prinse, D J. Ottaway, E Klantsataya, L d. S Teixeira, B W. Smith, T B. Payten, G Tsiminis

Single wavelength fluorescence sensing has been used in the preconcentration of ores for many years in situations where it is typically specific to the mineral of interest. Examples of fluorescence sensing include the sorting of diamonds in diamond mines and the sorting of scheelite in tungsten ores. However, the number of minerals that show useful single wavelength fluorescence properties in the visible spectrum is relatively small, so the application of fluorescence sensing is currently limited to niche application in the minerals industry. Recent developments at the University of Adelaide have focussed upon extending fluorescence signal measurements into the infrared spectrum, as well as investigating multi-wavelength fluorescence known as up-conversion fluorescence. These techniques may not only significantly increase the number of minerals that exhibit fluorescence properties suitable for both identification and sensor-based sorting, but also provide mineral-specific signatures of higher quality than previously attainable. This paper details the research work carried out by the University of Adelaide and funded by CRC ORE to develop a mineral-specific fluorescence sensor. The sensor targets two fluorine bearing minerals, fluorite and fluorapatite, that are common in many base metal ores such as porphyry copper ores and silver/lead/zinc ores. Fluorine is a known penalty element in mineral products derived from these ores, so mining companies need to monitor and control the amount of fluorine in their final product to keep it below commercially agreed specifications. Currently there is no real time sensor capable of monitoring fluorine in the ore feed so monitoring and control is carried out using time-consuming standard sampling and off-line laboratory measurements. The development and application of a real time fluorine sensor will enable the mining companies to monitor and control fluorine levels in the plant, greatly reducing the time and cost associated with producing their mineral concentrates within the prescribed specifications.

Nov 10, 2020

This paper examines the complex interplay of deposit characteristics, mining plans, tailings disposal techniques and rehabilitation requirements on planning for mineral sands operations. All component parts of this mining cycle are interdependent and cannot be evaluated in isolation when optimising a mineral sands operation. This is most evident when projects are large-scale or involve resources that contain complexities such as high slimes content, consolidated hard band materials, acid forming materials and radioactive materials. Projects located in environmentally sensitive areas add further to the need for more stringent planning. This paper describes the analysis techniques adopted by Hatch to evaluate mining and tailings placement options for a dredging and floating concentrator system. The principles and methods used in the analysis are applicable to any mining system involving the complexities listed above. The focus of this paper is on the reconstitution of mined material as tailings and the impact of this process on mining schedules and tailings construction and placement options.

Jan 1, 2001

By A Karrech, C Schrank, O Gaede, I Canbulat

Strain-based failure criteria have several advantages over stress-based failure criteria: they can account for elastic and inelastic strains; they utilise direct, observable effects instead of inferred effects (strain gauges versus stress estimates) and they model complete stress-strain curves, including prepeak, non-linear elasticity and post-peak strain weakening. In this study, a strain-based failure criterion derived from thermodynamic first principles utilising the concepts of continuum damage mechanics is presented. Furthermore, implementation of this failure criterion into a finite element simulation is demonstrated and applied to the stability of underground mining coal pillars.In numerical studies, pillar strength is usually expressed in terms of critical stresses or stress-based failure criteria where scaling with pillar width and height is common. Previous publications have employed the finite element method for pillar stability analysis using stress-based failure criterion, such as Mohr-Coulomb and Hoek-Brown, or stress-based scalar damage models.A novel constitutive material model, which takes into consideration anisotropy as well as elastic strain and damage as state variables, has been developed and is presented in this paper. The damage threshold and its evolution are strain-controlled, and coupling of the state variables is achieved through the damage-induced degradation of the elasticity tensor. This material model is implemented into the finite element software Abaqus and can be applied to 3D problems.Initial results show that this new material model is capable of describing the non-linear behaviour of geomaterials commonly observed before peak strength is reached as well as post-peak strain softening. Furthermore, it is demonstrated that the model can account for directional dependency of failure behaviour (ie anisotropy) and has the potential to be expanded to environmental controls such as temperature or moisture.CITATION:Gaede, O, Schrank, C, Canbulat, I and Karrech, A, 2014. A strain-based failure criterion for pillar stability analysis, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 393–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By M Zoorabadi

Overcoring is a common technique to measure in situ rock stress using the concept of stress relief. The strains measured during overcoring are used to calculate the stress tensor assuming continuous, homogeneous, isotropic and linear elastic behaviour. This approach does not recognise any effect of the thickness of the rock annulus produced during overcoring instead assuming that the stresses are entirely a function of the difference in strain between the start of the overcoring and the end with no regard to the transient strains produced. Three-dimensional numerical modelling was used to simulate the overcoring process and investigate the impact of core diameter on the transient stresses and strains during overcoring. This study showed that in thicker core, maximum transient axial stresses and strains occur when the drill bit approaches the measuring point and greater tensile axial stresses were produced when the annulus was thinner. CITATION:Zoorabadi, M, 2018. Numerical study of annulus thickness on overcoring stress measurements, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 274–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By S Hayton

While coal seam gas is considered to be an unconventional gas, the proliferation of areas under exploration and development mean that it is rapidly becoming main stream. The potential of New Zealand's coals to produce coal seam gas has been recognised for some time. However, key market drivers have not been suitable for the progression of this potential into reality. Kenham Holdings Ltd and CRL Energy Ltd, recognising the potential for the gas in New Zealand have initiated what is the largest ever assessment of New Zealand's coal seam gas potential. The premature demise of the giant Maui field has raised the focus of new gas developments and has increased interest in what we are doing. Over the past couple of years Kenham Holdings Ltd and CRL Energy Ltd have approached the assessment of the coal seam gas potential in a staged programme. Preliminary assessment of the data on the permit areas indicates that the potential resource may be up to 500 PJ. To date, preliminary appraisals have been completed or are underway on a significant number of fields. Exploratory drilling has been completed or initiated on several of those fields, with results from this work being fed into the preliminary modelling as it has become available. Given that in many of these areas there is no pre-existing information concerning their gas potential and world wide experience with lignite is practically nonexistent, it has been a steep learning curve with many surprises. However, initial gas content results and preliminary gas flow models have been on the whole, rather pleasing, with the commerciality of some developments already apparent.

Jan 1, 2003

By P M. Dight

Shotcrete usage in declines and developments has become pervasive as operators strive to achieve production improvements. Issues of mix control, fibreload, thickness control, temperature and curing conditions all play a part in the quality control. Often to overcome some of the quality control issues designers over specify the strength requirements in order to meet their operational constraints. Adherence to the standard civil testing requirements of 28 days moist cured at 21ºC without properly calibrating these results to the changing environment underground leads to contractual disputes. There are a number of standard tests specified including cylinder tests, cored tests, beam tests and round determinate panel (RDP) panel tests. The logistics of storing these samples and then transporting them to concrete testing laboratories without due regard to temperature changes with time can influence the results. All the samples can be readily handled by personnel except the RDP panel. The standard RDP panel is 800 mm diameter by 75 mm thick and requires an ITH machine at the mine and a fork lift at the laboratory to move it around. This paper will examine the possibility of a panel which provides scalable results to the standard RDP panel but can be easily handled by personnel and/or tested on site with suitable equipment. This allows for faster turn around and better quality control for the sample prior to testing. This enhances the identification of quality control issues at the mine and improves safety.

Mar 21, 2011

By A Manfrino

The Iron Bridge magnetite mine and infrastructure project is currently in development as a joint venture between Fortescue Metals Group, Formosa and Baosteel. It is supported by an extensive database of reverse circulation drill hole samples analysed by X-ray fluorescence (XRF), with a large subset tested for concentrate mass recovery, concentrate and tail grades by Davis tube recovery (DTR) testing. A limited number of rock physical testing results, including unconfined/uniaxial compressive strength and crushing work index, completes the database.By combining all available information – assays, DTR results, geology, stratigraphy, mineralogy and rock physical results – and using multivariate statistical analysis techniques, the impact of the critical factors that control concentrate quality, mass recovery and grindability characteristics have been outlined. A set of geochemical groups was created by using a cluster analysis technique from the combined XRF-DTR data. These groups allow optimal separation of material with consistently high concentrate Fe grades and mass recovery. This approach is superior to domaining based on stratigraphic logging or mass recovery as it is commonly used in standard magnetite estimation models. Using the results of a normative mineralogy study, the main geochemical groups were given a mineralogical profile fitting their geochemical characteristics. These findings further refined the understanding of the link between the process characteristics of the samples and their geochemical signature and mineralogy.The geochemical grouping defined on head grades and DTR concentrate mass recovery was generalised into a ‘geomet’ code based solely on the routinely assayed head grades, thus bypassing the need for systematic DTR testing. The geomet code identifies spatial domains with homogeneous geochemistry, mineralogy and process characteristics in both oxide and fresh material that form the basis of the current Iron Bridge resource model. The allocation of geometallurgical characteristics in terms of concentration amenability and concentrate characteristics on a block-by-block basis over the whole project allows for an optimum mine schedule and plant feed. This ensures that the desired concentrate characteristics and mass recovery can be better predicted over the life-of-mine, thereby improving the mine’s economics and stability by derisking the mine schedule and optimising the performance of the concentrators. A key benefit of the geomet code devised for the Iron Bridge mine is that it can be attributed in an automated manner to all samples analysed for a routine XRF analytical suite, from exploration to blasthole drilling. This allows each sample to be allocated to a geometallurgical material type with predictable process response in terms of concentrate mass recovery and concentrate quality without the need to complete systematic DTR testing.A standard multivariate analysis coupled with a cluster analysis has allowed the linking of interdisciplinary results between geology, mineralogy, geochemistry, process and metallurgy to better understand, predict and ultimately mine and process the Iron Bridge deposits. This allows plant operations and product quality to be optimised through each stage thanks to the predictable ore characteristics embedded in the mining model.CITATION:Manfrino, A, 2015. Unravelling the factors impacting on concentrate quality by geometallurgical data analysis at Fortescue Metals Group’s Iron Bridge magnetite mine, in Proceedings Iron Ore 2015, pp 567–578 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M J. Davies, R S. Davies

Despite increased expenditure, the global discovery rate of world-class ore deposits has been in decline for over a decade (Schodde, 2017). Mineral exploration has traditionally followed an empirical approach, searching for evidence of mineralisation upon the surface of the planet, then drilling to define the extent of an ore body beneath the surface. As outcropping deposits in well-defined areas are depleted, there is a need for exploration to extend to less well-explored search spaces. One popular new frontier is exploration at greater depths beneath the Earth's surface. However, exploring for deep deposits with limited surficial evidence requires the implementation of predictive targeting methodologies (Hronsky, 2011; McCuaig & Hronsky, 2014). The Mineral Systems Concept (Hronsky & Groves, 2008; McCuaig et al., 2010) provides a framework for predictive exploration targeting. Ore deposit formation is recognised to be a focused mineralising event. These events represent self-organising critical systems and are underpinned by the interaction of complex, non-linear processes. Through the collection and analysis of datasets that map mineralising processes, it may be possible to predict the size and location of resultant ore bodies. CITATION: Davies, M J and Davies, R S, 2018. Beyond below-ground geological complexity: Developing adaptive expertise in exploration decision-making, in Proceedings Complex Orebodies Conference 2018, pp 95–98 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By A Liu, X Wang, W Peng, Q Zhang

Pulp rheology plays a critical role in fine mineral flotation. Yield stress and apparent viscosity are two important rheological parameters affecting mineral flotation recovery. In this paper, the concept of pulp rheology and its measuring method are presented. The main factors, such as particle size, pulp concentration, mineral types, pulp temperature, inorganic salts, that affect the pulp rheology are systematically reviewed, and then followed by the discussion of the relationship between pulp rheological properties and flotation performance. Generally, high pulp apparent viscosity and yield stress values have been found to have an adverse effect on flotation recovery. In addition, due to the hetero-coagulation between the valuable mineral and gangue mineral, the pulp of mixed ore shows higher viscosity than that of the single mineral slurry. This paper is expected to provide some references for the efficient upgrading of low-grade and complex ores from the perspective of pulp rheology.

Aug 24, 2022

In May 2000, Kanowna Belle Gold Mines (KBGM) carried out a detailed Truck versus Shaft Haulage Study. The study showed that whilst the shaft option had many operating cost benefits the capital costs were too high, therefore the truck option was selected. In May 2001, the concept of achieving æshaft typeÆ benefits without the capital costs was floated. This is achieved by separating the hoisting of ore from other mining activities. The general concept is that material from underground is transported to a central location and then transported to the surface by a special truck fleet, thus removing the dependency between trucks and loaders, providing the mine with surge capacity and decreasing operating costs. At KBGM these advantages have been gained by installing an ore pass system with a plate feeder at its base that directly loads trucks. This provides the mine with a haulage system with enough surge capacity to remove the interdependency between trucks and loaders. The plate feeder is situated just off the decline which creates the opportunity to use larger more reliable, lower cost trucks. A number of truck types were considered for the truck loop including Elphinstone AD55Æs which are the truck type being used on site prior to the truck loop, CAT 775EÆs and power trailer road trains. This paper covers the philosophy behind the truck loop, the truck selection process, project installation and commissioning, people issues and the benefits expected by the operation. As of May 2002, the project is nearing completion, with decline haulage expected to commence in July 2002.

Jan 1, 2002

The importance of the accurate determination and interpretation of the bulk density and porosity of a given iron ore deposit is very often disregarded or neglected. Large amounts of time and money are spent on delineating and testing orebodies, and yet one of the most important factors in resource evaluation is sometimes estimated or, at best, determined from existing data from similar deposits. The Thabazimbi and Sishen South iron ore deposits are two well-known economical occurrences of high-grade iron ore in South Africa. Both these deposits formed as secondary enrichment of banded iron formation lithologies. Ongoing density studies on both these deposits are underway and results thus far proved very effective and necessary. Small-scale methods are used to determine average values for different ore types on both deposits. These values are used in resource estimation and geophysical interpretation.

Jan 1, 2007

By O Jones

Longstanding occupational health challenges of the underground hard-rock mining sector require both an analysis of historical data to assess evidence of linkages between the source of the problem and subsequent illnesses, as well as investigating the means by which health risks to workers can be eliminated or minimised. This paper refers briefly to a recently established National Health and Medical Research Council (NHMRC) sponsored Epidemiological Study into the incidence of Lung Cancer, contracted by mineworkers in Western Australia (WA) due to the inhalation of diesel exhaust fumes from 1996 to 2012. Thereafter it reviews current knowledge of the nature of the challenges facing those responsible for the health and wellbeing of underground hard-rock miners in WA, commencing with the recent categorisation of diesel exhaust as ‘Carcinogenic to Humans, Group 1’, by the World Health Organisation’s (WHO) International Agency for Research on Cancer (IARC). An attempt is also made to explore how the challenge has changed with the adoption of more advanced engine technologies, including the increased generation of ultra-fine volatile organic and other nucleates, submicron carbonaceous agglomerates and toxic gases.The compounding effect of using the mine decline access entry as both the primary ventilation intake and haulage-way is also discussed, as is the need to develop a more appropriate metric for regulating diesel engine emissions. Finally the paper refers to ongoing in-mine research pursued by the National Institute for Occupational Safety and Health (NIOSH) at its Diesel Laboratory in an underground limestone mine near Morgantown in the USA.CITATION:Jones, O, 2015. Diesel exhaust and the underground miner in Western Australia, in Proceedings The Australian Mine Ventilation Conference, pp 167–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015