Search Documents

By B Stewart

The SRS-1200 concept came about following the recommendations from the Board of Inquiry into the 1994 Moura No 2 mine disaster with the aim of having a system to remove personnel from an unsafe environment underground via a shaft where no other means of escape is possible. It is a mobile rescue unit that utilises a winding system to operate a man cage. It can descend the cage up to 1200 m into a vertical shaft. This operation is managed from the winder control compartment located on the non-driver side at the rear of the vehicle.

May 5, 2022

By D Zielinski-Nicolson

The emergence of affordable, portable and versatile wireless devices has enabled a new frontier in mine safety equipment. Existing solutions provide methods for tracking personnel and assets in underground mines but are not designed to optimally integrate into existing and emerging systems. Mine management are often required to coordinate primarily independent emergency, personal protective equipment (PPE), tracking and collision avoidance systems from multiple vendors. These systems involve a variety of wireless technologies that require separate integration projects that discourage adopting new services and policies.

May 5, 2022

By A Hocking, S Henderson

Commonwealth of Australia (2016) defines rehabilitation as comprising “the design and construction of landforms as well as the establishment of sustainable ecosystems or alternative vegetation, depending upon the desired post-operational land use”. For open cut coal mines in Queensland and New South Wales, the question of how to apply this intent to pits at mine closure is repeated for hundreds of individual pits. In EISs, closure plans and public discussion, assorted treatments are proposed to rehabilitate pits. While some aspects of final voids have been intensively studied, there is little guidance on how to choose a final void treatment option that delivers the optimal outcome against rehabilitation goals. For example, in the Bowen Basin and Hunter Valley commonly proposed rehabilitation actions include reducing the angles of pit walls; however, with few voids successfully rehabilitated to date there is limited understanding of what different wall slopes will achieve.CITATION:Henderson, S and Hocking, A, 2018. A decision framework for comparison of coal void rehabilitation options, in Proceedings Life-of-Mine 2018, pp 127–130 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By M I. Pownceby, N A. S Webster, J R. Manuel, J M. F Clout, E Donskoi, N A. Ware

The relative influences of sinter mineralogy, sintering temperature, solid and pore macro- and microstructure on iron ore sinter physical strength are not yet fully understood. Whilst a range of analysis techniques have been used by researchers to evaluate sinter physical properties and sinter mineralogy, none have been able to directly link sinter mineralogy and physical strength under controlled conditions. CSIRO has developed a unique laboratory method to study the fundamental melting properties of fine iron ores in a laboratory furnace under a controlled temperature and gas atmosphere environment designed to simulate the industrial sintering process. Compacted tablet samples for a 0.41 per cent and a 2.5 per cent Al2O3 series were fired in a tube furnace at various temperatures, cooled, then tumbled using a modified Bond abrasion test apparatus to determine a relative tumble index (TI) at each temperature. Quantitative XRD (QXRD) analysis was then carried out on the tumbled samples and optical image analysis (OIA) was conducted on polished sections of a separately fired compact in each case. The amount of total SFCA was found to decrease with increasing firing temperature for both alumina series with the total amount of SFCA higher in the 2.5 per cent Al2O3 series compared to 0.41 per cent Al2O3 series samples. The increase in the amount of magnetite and hematite with increasing firing temperature was largely at the expense of a decrease in total SFCA. Overall, there was good agreement between the quantitative mineralogy determined from QXRD versus OIA for SFCA, hematite and magnetite. Qualitative analysis of high magnification images of the sinter correlated with both the OIA and QXRD results.

Sep 18, 2023

By A Gray

Physical separation features in almost every mineral processing circuit. The category encompasses a broad range of techniques and technologies including hydrocyclones, gravity concentration methods (including jigs, spirals, centrifugal concentrators, tables, heavy media separators) and thickeners, all of which make use of the inherent density differences between two mediums. It is also possible to include flotation, magnetic separation, and ore sorting in the physical separation category.However, opportunities for enhanced physical separation performance can now go beyond the common practice of optimising unit operations. Improved options exist for feed preparation ahead of the physical separation stage, enabling higher performance and lower cost outcomes for physical separation flow sheets and technologies.The use of new applications in breakage technologies combined with mineral liberation analysis to optimise liberation prior to the physical separation stage provides options for preconcentration and gangue rejection as well as better separation efficiency. The use of low cost gangue rejection and preconcentration can be an intermediate step between mining and processing that allows processing of lower cut-off grades from the mine whilst delivering higher grades to the mill.Optimising flow sheets and technology performance requires detailed understanding of particle size and shape distributions as well as liberation characteristics to suit the particular separation unit, combined with knowledge of the available technologies, their capabilities and the economic impact across the whole mine cycle.CITATION:Gray, A, 2017. The role of liberation in physical separation techniques, in Proceedings MetPlant 2017, pp 147–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By F Tang, Ö K. Büyükuslu, M Baben, S Petersen

GTT-Technologies’ ChemApp for Python was developed to provide a powerful, easy to use interface to ChemApp for a programming language highly popular with scientists and engineers. It is used, for instance, by GTT to develop program modules such as the CALPHAD Optimiser for the FactSage™ software, by customers to move from interactive FactSage calculations to perform versatile scripting with Python, and by GTT and its partners in research projects in the area of materials informatics. Computational thermochemistry is fundamental for advancing sustainable metallurgy and creating new alloy compositions for engineering applications. Materials informatics involves handling vast amounts of data and complex workflows. GTT’s approach uses ChemApp for Python and the FactSage thermodynamic databases to design recyclable alloys from the start, incorporating a higher percentage of scraps while aiming to simplify the workflows to simulate material design steps. Challenges arise due to recycling scraps, introducing more elements for consideration. CALPHAD-based databases accurately cover materials from primary metallurgy, but additional data for minority and critical elements is crucial for precise computational modelling. GTT combines machine learning-based ab-initio databases with traditional CALPHAD databases to cover the complete chemical space with appropriate accuracy. The design of a hardfacing alloy through a high-throughput materials informatics approach is used as a demonstrator of the current possibilities.

Jun 19, 2024

By C Harwood

Underground coal mines in the United States are in the process of completing installations for tracking and communication systems, mandated by Congress after a number of recent coal mine disasters. Yet, evaluation, modelling and testing of such systems has lagged due to legislated changes, abruptly introduced into the coal mining industry. System installation in a wide array of mine types, configurations, layouts and characteristics has provided a wealth of information regarding their potential in underground environments. Data collected from numerous installations for a variety of systems can be used to further define true capability and accuracy of communication and tracking packages. This paper describes a uniform means of evaluating the performance of a communication and tracking system. Several performance measures are proposed and described. These measures can also be predicted using an interactive software program. This program predicts the signal propagation, given the input mine characteristics and layout, with numerical and visual feedback. New or alternative system installations can also be more accurately designed to potentially minimise initial system cost and time required for trial and error installs. The focus of this research is to develop tools and protocols that can evaluate and measure the effectiveness of installed underground communication and tracking systems.

Nov 22, 2011

By J Theiler, B Beamish

Spontaneous combustion hazard assessment from an environmental impact perspective is not well understood and is seldom given due consideration in environmental impact statements. In surface mining operations, self-heating, leading to spontaneous combustion may occur when rock units containing reactive metal sulphides and organic carbon are disturbed by mining operations and exposed to the atmosphere. When these rocks are present self-heating will occur in situations where the rate of heat generated from oxidation reactions exceeds the rate of heat lost to the surroundings. The processes and mechanisms that lead to spontaneous combustion events are varied and generally complex. To effectively manage spontaneous combustion in surface mining operations, it is necessary to characterise the spontaneous combustion propensity of the geological materials involved. Until recently there has been no testing procedure for assessing the propensity of waste rock to spontaneously combust that has been adopted by industry. However, new developments in adiabatic test methods have proven successful in determining the self-heating behaviour of coal (Beamish and Theiler, 2015) and coal containing reactive pyrite (Beamish and Theiler, 2017). These adiabatic test methods have now been modified to assess the incubation behaviour of waste rocks and can be used for their spontaneous combustion characterisation in advance of mining (Beamish and Theiler, 2016). The new method provides a practical means to establish the likelihood of developing a spontaneous combustion event for the specific site conditions. This paper presents examples of the use of a cost effective first pass filter for assessing spontaneous combustion potential of waste rock based on geochemical data from four surface mines. This is supported by adiabatic Incubation Test results for three of the mines and visual examination of cores for one of the mines. CITATION:Theiler, J and Beamish, B, 2018. Valid spontaneous combustion hazard assessment for surface mine environmental impact statements, in Proceedings Life-of-Mine 2018, pp 64–67 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By J E. Everett, F Grobler

This study considers realistic data for a planned open pit iron ore mine, but is applicable to any open pit situation. By interpolating drill hole data, grades are generated for a rectangular block model. Each blockÆs grade designation vector has components for each analyte (chemical element or compound) influencing ore value. Interpolation by means of geostatistical kriging leads to each block being assigned its expected value, and thus underestimates the overall grade variability. Alternatively, interpolation by means of conditional simulation is a method that implements random sampling from an infinite population of solutions. Each conditional simulation has appropriate overall grade variability, but estimating any blockÆs mean and variance requires sampling from multiple conditional simulations. For a block model, an ore/waste selection criterion maximises the expected tonnage at a target grade. This criterion is a linear composite of the grade components, with positive coefficients for the beneficial analyte (iron) and negative coefficients for the deleterious analytes (such as silica, alumina and phosphorus).Although conditional simulation gives the same expected grade as kriging for each block, the expected maximum tonnage of ore selectable at a target grade may differ from that obtainable from the kriged solution. We apply the linear composite selection criterion to each of 25 conditional simulations, as well as to the kriged block model. The resulting distribution of product tonnage is confirmed to have an expected tonnage that is over 20 per cent greater than that of the kriged model. The method also enables a selection probability to be computed for each block, and thus a probabilistic pit boundary distribution to be identified and used in mine planning. Proposed extensions will consider risk-based scheduling of the multiple selection solutions through minimisation of a derived æstress factorÆ and treating the mining process as an iterative system with actual or artificial ædepletionsÆ modelled in line with the mine plan, using the updated state (with new information) to re-evaluate the mine plan for subsequent periods.CITATION:Everett, J E and Grobler, F, 2013. Risk-based ore selection from conditionally simulated block models, in Proceedings Iron Ore 2013 , pp 149-156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By V O’Brien

The suitability of magnetic surveys flown at low altitudes to identify buried heavy mineral (HM) strands has long been accepted. This is despite the low intensity magnetic response often obtained from such strands. The fundamentals of the magnetic survey method dictate that the closer the instrument is to the source the stronger the response. As such the optimal elevation for the magnetometer is at or near the surface. Iluka sought to use a ground based magnetometer to aid in the exploration target generation process and allow accurate targeting of exploration drill holes. Following the initial trial Iluka recognised the potential additional application of data obtained by a ground based magnetometer over known strand deposits. The detail of the ground magnetic images can confirm the assumed strand continuity between cross-sections of close spaced drilling and can aid in the definition of the geometry of different generations of mineralisation. The ability to confidently determine that the deposit has not been truncated by post emplacement erosion of the mineralised deposit may enable reductions in drilling requirements as well as assisting mine planning activities. Iluka intends to investigate advanced modelling of the magnetic data to determine the level of strand geometry and HM content resolution that can be achieved from the ground magnetic survey data and its potential application in the mining grade control process.It is anticipated that the surveying of Iluka’s known resource deposits will provide the ability to correlate the magnetic response from new exploration targets with those from known deposits for a given depth, HM grade and mineralogy suite.

Oct 5, 2011

By Y-B Kang, W-Y Cha, Y-M Cho

Molten slag used in the secondary refining process (RH process) for the production of Ultra-Low C (ULC) steel is typically composed of CaO-Al2O3-MgOsat.-FetO with minor constituents. FetO in the RH slag is the main source of reoxidation of the molten ULC steel in the ladle by 2Al + 3(FetO) = (Al2O3) + 3Fe, thereby serving as the source of the alumina inclusions. On the other hand, FetO also enhances the fluidity of the slag, thereby increasing inclusion absorption capacity. Optimum slag chemistry design is therefore required to produce clear ULC steel. The reoxidation kinetics was investigated in the present study by employing high-temperature experiments and developing the reaction rate model. Initial compositions of slag ((% CaO)0/(% Al2O3)0 and (% FetO)0)) and reaction temperature were varied and change of [% Al] in the molten steel was measured. The rate-controlling step was analysed. It was found that the rate-controlling step in some cases changed during the reoxidation: from a mass transport of Al in the molten steel to a mixed transport including Al2O3 in the molten slag. The experimental data validated the reaction rate model based on the elucidated reaction mechanism and FactSage thermodynamic database. The model suggested that high (% CaO)0/(% Al2O3)0 suppresses the reoxidation only when (% FetO)0 is low (5 or lower in the present study).

Jun 19, 2024

By B Belle

In a deep, gassy predrained coalmine, ventilation and goaf drainage systems act as critical controls to manage longwall (LW) panel return gas levels. The goaf capture efficiency of most LW panels ranges from 45 to 85 per cent based on the gas domain at respective workings. Recent operational experiences have indicated that 50 m goaf hole spacing is optimal for management of high production retreat gassy LW panels, where the probability of goaf hole failures are frequent. Due to the horizontal stress direction geotechnical issues, goaf hole failure just behind the LW face is a recurring challenge resulting in significant and immediate increases in LW panel return gas levels. This paper presents a successful implementation of an innovative LW tailgate (TG) road cut through seal goaf fan/venturi system. The system incorporated a 17' (400 mm cased) hole drilled to 320 m deep in a perimeter roadway on a retreating LW TG road drawing the working seam horizon goaf gas behind the perimeter of seals. The surface goaf fan/venturi system was aimed to safely exhaust the LW deep goaf gas and thus withhold the goaf stream spillage to TG drive area and reduce the panel gas load by controlled operation of the system using continuous monitoring of CH4, CO and O2 levels. This control philosophy was made operational without impacting the use of the perimeter inbye ventilation shaft used for mine cooling and providing additional ventilation dilution capacity. The instantaneous reduction in TG gas levels of up to 0.3 per cent was observed even when the LW was 300 m away from the c/t seal goaf hole. Success of this concept TG seal goaf gas control system used even when the LW was 1300 m outbye has become an inventory of additional control for future deep and long LW blocks. This paper attempts to share the design process in addressing other risks and desired outcomes in managing the LW gas levels.CITATION:Belle, B, 2015. Innovative tailgate mobile goaf gas management in two gate road longwall panels – concept to implementation, in Proceedings The Australian Mine Ventilation Conference, pp 31–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By L Tatnell, R Mackay, A Tolooiyan

The multi-reversal direct shear test (MRDS) method is commonly used to measure the residual shear strength of soils. However, when the standard direct shear (DS) apparatus is used, the MRDS method is prone to two major sources of error: load cap tilting and specimen loss. These two sources of error can cause erratic behaviour in the residual shear strength curve, making it difficult or even impossible to determine the correct residual shear strength value of the specimen being tested. This paper presents the results of new modifications to the standard DS apparatus that prevent load cap tilting and specimen loss. Consolidated drained testing was performed on highly-over consolidated cohesive soil samples from a Latrobe Valley open pit mine, with results obtained from the modified DS apparatus showing a great improvement in the residual shear strength profile compared to those obtained using the standard apparatus. Large numbers of reversals (up to 14) conducted on a single specimen in the modified DS apparatus showed no notable load cap tilting and no specimen loss occurred. The modifications are easily applied to the standard DS apparatus, and analysis and correction of the data are simple.CITATION:Tatnell, L, Tolooiyan, A and Mackay, R, 2014. Measurement of residual shear strength using a modified direct shear apparatus, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 425–434 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By G R. Hancock, J F. Martín Duque

Post-mining landscapes are required to geomorphologically and ecologically integrate with their surrounds (Martín Duque et al., 2015). Designing and constructing an erosionally stable landform is the first and arguably most important part of the rehabilitation process. Without an erosionally stable landform topsoil and nutrients are lost, shallow groundwater is depleted as well as when excessive erosion occurs, expose suboptimal materials. Here we examine the ideas of geomorphic design and rehabilitation and how the landform can be tested and enhanced using computer based design and landscape evolution models. Specifically we evaluate the complementary capabilities of landscape modelling (SIBERIA) (Hancock and Willgoose, 2017) and geomorphic design software (Natural Regrade with GeoFluv) (Bugosh et al., 2016), in order to maximise erosional stability on post-mining landscapes (Zapico et al., 2018). CITATION:Hancock, G R and Martín Duque, J F, 2018. Geomorphic design and landscape evolution modelling for best practice mine rehabilitation, in Proceedings Life-of-Mine 2018, pp 119–121 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By A Kite

Frontline leaders play a critical role in the safe and productive operations of Australia’s mining, resources and heavy industries. These leaders set the workplace culture, especially during night shifts and weekends, by providing team direction and encouragement, providing access to resources, fulfilling statutory requirements, enacting and reinforcing risk management systems, setting the standards on shift and acting as the primary conduit of communications between senior leaders and team members.

May 5, 2022

By R Yang

This paper presents a fragmentation model for large production blasts in an open pit or underground environment. The paper shows that the particle velocity is directly related to pressure, strain, and strain rate and so it can be considered as driving force and mechanism of rock fragmentation. This is supported by the fact that a vibration with a larger peak particle velocity (PPV) generates larger disturbance in rock and so finer fragmentation or more blast damage than a low PPV. The crack distribution in rock from impact is based on findings from previous researchers (Seaman, Curran and Shockey, 1976; Liu and Xu, in press). The fragmentation size is calculated at three-dimensional grid points within a blast. The fines and oversized blocks are calculated explicitly – the fines generated close to blastholes and big blocks far from boreholes are modelled naturally. The multiple blasthole fragmentation (MBF) model takes surveyed irregular geometry of the free face of a blast as the calculation boundary. The MBF can model fragmentation with over one million grid points. Examples of the model’s field comparison are also included.The PPV at a calculation grid is estimated based on the same approach used for the near field non-linear vibration model (Yang and Scovira, 2007). The method is based on the dominant charge for a calculation grid point, non-linear charge weight superposition within a charge and from multiple charges, strain wave broadening, and amplitude attenuation with distance from a charge segment. The blasthole confinement affected by earlier firing charges is also taken into account.The MBF model inputs from blast design, such as: location and orientation of each blasthole, stemming length, blasthole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect of the delay and its scatter in each blasthole on fragmentation and has a statistical modelling capability for geological random variation on attenuation of particle velocity wave. The wave reinforcement due to instantaneous waves arriving or diminishing cooperative contribution due to long delay intervals between charges is also simulated.The results are displayed in 3D volumetric plots, contour of fragmentation in cross-sections, and size passing curves for a whole blast or a region of the blast.CITATION:Yang, R, 2015. A multiple blasthole fragmentation model – its concept, formulation, capability and field comparison examples, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 177–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M de Freitas Silva

One of the main steps during the decision-making process of long-term mine planning is the definition of the optimal sequence of extraction, which usually is synonymous with maximising the discounted cash flow of the project subjected to several constraints arising from aspects of technical, physical, and economic limits.Open pit mine production scheduling (OPMPS) comprises several intricacies related to its size and uncertainty of input parameters. Due to its complexity and prohibitive size, traditional mine planning usually relies on heuristic or metaheuristic methodologies which are able to provide good solutions in a reasonable amount of time. However, most of the uncertainty that surrounds the mining complex is ignored leading to non-realistic results.In this paper, a new heuristic approach is explored in order to solve a stochastic version of the OPMPS problem accounting for geological uncertainty in terms of metal content, multiple processing streams, and stockpiling option. The methodology involves generating an initial solution by solving a series of subproblems and this initial solution is improved using a network flow based algorithm.The algorithm was applied to a relatively large gold deposit with more than 119 thousands blocks. Results have shown that the methodology is promising to deal with large-size mine instances in reasonable time.CITATION:de Freitas Silva, M, 2014. Solving a large stochastic integer programming model for production scheduling at a gold mine with multiple processing streams and uncertain geology, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 389–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By N Boughen, K Moffat, L Brooks, A Zhang

In 2015, Ernst and Young (EY) ranked socio-political license to operate (SPLTO) as the fifth greatest challenge to the mining sector (EY, 2015). The EY report asserts that SPLTO will continue to present a risk to the mining sector in the context of ‘increased activism, digitally connected stakeholders and politicians who need to respond to general consensus’. While there is no consensus on a definition, SPLTO is commonly regarded as the ongoing acceptance or approval of an operation by affected stakeholders (Moffat and Zhang, 2014; Thomson and Joyce, 2008) as well as those stakeholders that can affect the operation (Graafland, 2002). Warhurst (2001) relates the process of stakeholders granting SPLTO to the establishment of meaningful partnerships between operations, communities and government based on a variety of factors that build trust between stakeholders.From these accounts, we can see that understanding stakeholder attitudes about company performance and impacts on stakeholders directly affected by an operation are important in any attempts to measure SPLTO. Understanding the level of acceptance of an operation within these stakeholders provides a good proxy or outcome measure of SPLTO. Moreover, trust seems to be a central variable in the translation of these experiences of an operation into acceptance. What the mine or company does, its behaviour, degrades or builds trust with stakeholders, and this then affects acceptance (Moffat and Zhang, 2014).In addition, a strong emphasis is placed on the nature of the relationship between companies and stakeholders as influenced by inter-group interactions. It is not just what companies do well or poorly with respect to environmental impacts, for example, that will determine trust and acceptance, but how the company relates to its stakeholders at personal and group levels.These relationships between communities of stakeholders and extractive companies are dynamic. Brown and Fraser (2006) recognised the importance of industry being able to respond to the changing nature of societal approval and acceptance, arguing that ‘business must have regard for evolving social attitudes and expectations if it is to maintain its ‘social licence’’.This paper will describe a series of five pilot projects conducted by CSIRO with Anglo American in Australia and South Africa to generate a real-time understanding of SPLTO to guide more reflexive and effective social performance strategies.CITATION:Moffat, K, Boughen, N, Brooks, L and Zhang, A, 2016. Social licence in real-time – using dynamic methods to support a new kind of community relationship, in Proceedings Life-of-Mine 2016 Conference, pp 191–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

The current economic climate and demand for iron ore has resulted in mine operators being prepared to accept aggressive slope designs and associated failures provided that they can be quantified (ie volume of failure and clean up costs, etc) and incorporated into the mining costs, at a feasibility study level. This has numerous implications for pit slope design/geomechanics. Typically when geotechnical engineers conduct slope stability modelling a single value, usually the average or mean value for model input parameters (ie structural orientations, material properties and hydrological conditions) are chosen. The implications resulting from using a single value for model input parameters will vary depending on how the modeller has chosen the value, ie should the modeller choose a mean value from a log-normal distribution of material strengths an optimistic representation of the stability may eventuate, consequently if the designer decides to conservatively downgrade the values by a nominal factor, a pessimistic representation of slope angles may occur, which would result in excessive stripping and mine development costs. A more realistic and representative way to model the inherent variability of geological/geotechnical conditions would be to do so probabilistically. Whereby the modeller can assess the variability of the geological structure as observed/recorded during the core logging process and a similar approach for the material strength properties. The final model output would be a distribution of factors of safety in relation to overall slope angles, ie probabilities of failure for individual slope angles could be determined. This output (graph) could be modified by the mining engineer to incorporate mining costs as well as clean up costs for the respective slope angles and associated failure volumes, ie probabilities of failure. The author intends to provide a detailed overview of the processes involved in deriving a geotechnical design, ie; starting from the data collection phase (core logging/face mapping), through to the data interpretation and formulation of slope parameters; determining the variability and uncertainties associated with each of the process; ensuring that it is adequately captured in the model input parameters; and how the mining engineer could utilise this information to derive final feasibility study mining costs.

Jan 1, 2009

By C Moorhead, J Jones

A common problem in the mining industry is that company geologists can operate in relative isolation to the rest of the company (Jones and Moorhead, 2011). This may result in poor knowledge transfer and often priority conflicts with geology, operations and project departments. This problem is amplified by the acquisition of mineralogy capabilities and other metallurgical (met) test work undertaken by many companies in order to solve for complex orebody problems. Met data is often not located and viewed in 3D space so that geologists and engineers can create and work with geometallurgical (geomet) models (Bye, 2006). Visualisation of data in an interactive graphical 3D model provides a bridge enabling met professionals to collaborate with engineers and geologists to provide a common understanding of the relevance of geomet data.In recognition of this problem, Newcrest has undertaken an effective collaboration strategy to improve internal and external engagement through the use of large visualisation displays (Jones, 2009). The displays are underpinned by IT systems and information management practices that recognise the needs of underlying disciplines. Today it is generally understood within Newcrest that this is required to improve decision-making, deliver faster cycle times and improve governance.Collaboration in companies has been generally associated with the introduction of new IT functions (IBM, 2008). However, the science and engineering process that are used to structure modern IT-based collaboration systems and practices are now known to be simplistic compared to the long-standing practices associated with collaboration and knowledge management in disciplines such as geology and mining.CITATION:Jones, J and Moorhead, C, 2013. Geometallurgical communication as a distributed information system, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 133-138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013