Search Documents

By L B. Zhou, S Li, B L. Wang, S B. Li, Q Wang

The rapid development in ChinaÆs metal mine resources has caused a series of mine environment problems such as serious ecological damage and environment pollution, and secondary geological disasters. The paper has reviewed ChinaÆs metal mine development, including current status and environmental situation, analysed existing problems in mine development and environmental management, and proposed corresponding countermeasures and suggestions.CITATION:Wang, B L, Li, S B, Li, S, Zhou, L B and Wang, Q, 2012. Current situations, problems, countermeasures and suggestions for ChinaÆs metal mine development, in Proceedings Life-of-Mine 2012 , pp 353-356 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By H Ishikawa, S Palaniandy

The gravity-induced stirred mill such as the TowerMill is an energy-efficient grinding solution used in secondary, tertiary, and regrinding duties in the mineral processing concentrator. The interest in this technology is emerging, with more than 300 mills installed globally in various grinding duties and commodities for the last 30 years. Although the technology is matured, there are still opportunities for improvement and the development of new knowledge to improve its circuit energy efficiency and reduce water consumption. Recent studies show that a combination of stress intensity, ore hardness, slurry density, and mill feed configuration can be used to evaluate the performance of the grinding circuit. A recent pilot-scale TowerMill test work at various stress intensities shows that a lower operating work index and size-specific energy were achieved at higher agitator tip speed and using medium size grinding media. These outcomes were confirmed through several site trials. A smaller 17 mm grinding media has reduced the operating work index and size-specific energy by 18 per cent and 11 per cent, respectively, compared to the 20 mm in a magnetite concentrator. Moreover, the conversion from top feed to bottom feed configuration has reduced the operating work index and size-specific energy by 13 per cent and 37 per cent, respectively. The circulating load was reduced by 34–38 per cent, leading to a reduction in the dilution water consumption in the hydrocyclone feed sump by 20 per cent. A variable frequency drive offers flexibility to change the stress intensities on the TowerMill, where a 35 per cent reduction in specific energy was achieved when the ore became soft. This paper explores the potential design and operating strategies that can be implemented to enhance the energy efficiency, reduce water consumption and reduce CO2 emissions in the circuit and finally evaluate its impact on the total cost of ownership.

Aug 24, 2022

By J White

The Eyre Peninsula (EP) has been known for its iron ore for more than a century. Edward John Eyre noted the ironstone outcrop at what is now Iron Knob in the 19th century. Sir Douglas Mawson visited and reported on the geology of the lower EP in 1906, noting the widespread presence of iron stone and the likelihood of copper being associated with the iron stone. Despite this knowledge there has been only one successful iron ore mining region developed on the EP and that is Iron Knob and the Middleback Ranges which have been mined continuously since 1899. The Middleback Ranges can justly lay claim to be birth place of the Australian iron ore and steel industries.The discovery of large scale haematite resources in Western Australia meant that there was no need to seek out iron ore that needed benefi ciation. The low price of iron ore precluded further development of the EP and many other areas in Australia and overseas. This situation changed rapidly in the mid-2000s with the emergence of China as the world’s industrial power house and the soaring demand and price for many resources including iron ore. This triggered a flurry of activity across Australia and led to the rapid exploration and drives to develop the EP iron ore. A brief examination of the magnetic maps of the EP shows the wide spread presence of magnetite and associated smaller haematite deposits. A closer look reveals the magnetite deposits to vary in formation style and host rock lithology as well as being significantly altered by regional metamorphism. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011

By M S. Fenzel

Increased environmental regulations and pressures have created changing and new demands for tailings management strategies in a variety of mining applications. Critical among these items is the disposal of tailings as the pursuit of increased yields and lower costs have driven the application of different process technologies. With a number of technologies having a niche application focus, the belt filter press has been utilised for decades as a cost-effective and versatile option for dewatering different types of mineral tailings and other waste process streams. One of the critical advantages of the belt filter press is the technology’s ability to adapt and work in numerous plant designs, operating conditions and applications. As permitting and disposal options have become more stringent, plant designers, operators and equipment suppliers must develop comprehensive and site-specific economic, design and process evaluation techniques to ensure proper equipment selection and system design for belt filter presses or any other dewatering technologies. This paper will explore these techniques in relation to belt filter presses (with reference to other technologies) in a variety of different applications, along with other considerations to ensure a successful tailings dewatering system and disposal design. Summaries of equipment performance characteristics, operating and maintenance strategies and optimisation techniques will also be addressed in conjunction with the belt filter press’s adaptability to different plant designs and the resulting tailings characteristics.CITATION:Fenzel, M S, 2015. Analysis and adaptability of belt filter presses and other technologies for tailings dewatering over a range of mineral processes, plant designs, conditions, regions and operating philosophies, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By K Seddon

Segregation of tailings on deposition can occur as a result of a) sub-aqueous deposition, and b) sub-aerial deposition at lower solids concentrations (i.e. when the solids concentration is less than the segregation threshold). The effects are likely to be more pronounced in the case of subaqueous deposition.This paper presents the results of an investigation of a sub-aqueous tailings facility.Data from the investigation show extreme variations in particle size and density compared to test results for non-segregated ‘all-in” tailings. The results indicate that on segregation both the fine and coarse splits tend towards a well sorted (poorly graded) mix, and both have significantly lower consolidated density than the all in tailings. This result is reasonably well known for the case of the segregated fines (“slimes ponds”) but less appreciated for the coarse fraction. The results suggest that if the effects of segregation are not allowed for, the overall density of the deposit can be seriously over-estimated at the design stage. Also the quantity of water retained in the tailings can significantly influence water recovery and water balance results.CITATION:Seddon, K, 2018. Segregating tailings – effects on density and water retention, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 299–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By S Brochot, M-V Durance

In many cases, current metallurgical accounting practice does not consider the errors associated with the measurements used in obtaining the metal balance. Considering all measurement errors, including errors associated at each step of the process - from sampling and analytical errors to measurement errors in circuit instrumentation, can improve the accuracy of the final metal balance - assisting in the improvement of process performance, optimisation and control.The consequences of the inclusion of measurement errors on metal balance for different circuit configurations and typical metallurgical accounting practice (two product and three product formulae) will be discussed in this paper.Examples of the tools, methodology of implementation, and periodical metal balance tasks are presented to illustrate the advantage of this approach in meeting the different requirements of each department.CITATION:Brochot, S and Durance, M-V, 2012. A new approach to metallurgical accounting, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 217-224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M A. Noppé

"Mining is an inherently risky business: from the technical, environmental, social and economic uncertainties associated with advancing an exploration concept to a viable project; to the risks associated with the operating, market, and safety risks and uncertainties attached to a developed mine; and the final mine closure process.Investors and other stakeholders assessing the risk, opportunity and relative value associated with a resource project need to appreciate the project in its correct context. Errors, omissions, biased reporting or conflicting information in reporting may result in a misinterpretation of technical and financial results, leading to biased estimates or assumptions on project value (Noppé, 2016).Simplistically, a project can be assessed on three key areas for positioning the project in its correct relative context, namely: the project development stage the confidence in the estimated quantities and qualities of the resource, reserve and/or product the level of accuracy, precision and confidence in the technical and economic studies supporting the project.In the latter case, the ‘technical and economic’ information includes assessing the necessary social, environmental and commercial/legal/governmental approvals for the project.Responsible management of a resource project through its full life cycle relies on competent and dependable control and direction being effectively provided by the technical, business and board leadership of the organisation. In turn, the project information must be effectively communicated between various disciplines, these disciplines and the company, and the company and its stakeholders.CITATION:Noppé, M A, 2016. Responsible management and transparent reporting across the project life cycle, in Proceedings Life-of-Mine 2016 Conference, pp 5–7 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By R McIlwraith, B Breul

"This paper discusses the successful use of bituminous geomembranes (BGMs) in mining applications since their development in 1974. It explains and illustrates the structure of a BGM composite, which is a geomembrane manufactured by impregnating a polyester geotextile with a compound of bitumen, elastomer and filler. Examples of applications of BGMs in the mining industry are also presented in the following contexts.Storage of solid waste: storage of mining waste at mines in Canada heap leach pads in France, Peru, Chile and Turkey at the base of a mining waste landfill in Brazil capping of solid mining waste in Chile and Canada temporary capping of mining stockpiles in Australia (with possible reuse of the BGM for other works).Examples of the application of BGMs for the storage of liquid waste in mining containment reservoirs in Canada, Guatemala and Peru will also be given.For each example given, reasons are supplied that supported the choice of BGMs by the clients and consultants, drawn from the following advantages of the BGM:BGMs have excellent puncture strength, due to the internal polyester reinforcement, as well as excellent ultraviolet resistance. This often eliminates the need for a cushion geotextile or cover soil over the BGM.BGMs have a very long life expectancy, in excess of 300 years, in subsoil conditions (Breul et al, 2004).BGMs can be installed in very harsh climatic conditions. They are suitable for high wind environments as their heavy mass per square metre makes them resistant to wind uplift. The low coefficient of thermal expansion means that BGMs are suitable for installation in mines where very low or very high temperatures are expected. This reduces construction delays and allows for a quicker use of the mining facility.The fact that the BGM can be installed by the mine’s own workforce, after appropriate training from the BGM manufacturer, allows for a more flexible construction sequence on the mine.Ability of the BGM to connect to other materials such as concrete, steel, rock and other geomembranes that may be on the mine site.The technical advantages of a BGM enabled the engineering consultants to prepare solutions for their mining clients that had a lower environmental risk, had a faster completion schedule and were overall a cheaper option than with a polymeric geomembrane.CITATION:Breul, B and McIlwraith, R, 2015. Bituminous geomembranes in mine construction, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 289–296 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By D Stacey, J Matthews

Hunter Valley Operations in partnership with Orica Explosives designed a process to optimise coal extraction at depths greater than 65 m below the Hunter River in a safe and cost effective manner. The process involved a team approach to investigate the relationship between geology, mining sequence, vibration and blasting methods adopted. From this an optimum method for uncovering the coal was developed.

Jan 1, 2001

By A Smith

Rock masses usually exhibit scale dependent mechanical properties primarily due to presence of discontinuities and their inhomogeneous nature. One of the essential preconditions for selection of appropriate strength and deformation parameters of a rock mass in relation to tunnel design is assessment of the scale of the joint network relative to the scale of excavation. In tunnel design practice, scale effects are estimated indirectly using small-scale unconfined compressive strength (UCS) tests and rock mass classification based empirical correlations. Large-scale UCS tests have the benefit of direct assessment of anisotropic and scale dependent properties of a rock mass.This paper presents results of a large-scale UCS test on a jointed siltstone. A 450 mm diameter sample with inclined bedding planes was cored and tested in uniaxial compression until failure with load and displacement measurements. The aim of the test is to determine strength and deformation parameters and correlate them with results of small-scale UCS tests of the same sample. The relationships between the small-scale and large-scale rock mass parameters were validated against published correlations from the literature.

Mar 8, 2011

By J Purandare, D Murdoch

The goal of the life-of-mine plan is to ensure that while the site is left safe, stable and non-polluting, the landscape is such that optimal use can be made of the site post-mining and closure. However, in the face of evolving shareholder expectations and the current international economic climate, numerous mines are ceasing operations and moving into a care and maintenance phase. These changes bring with them a high degree of community concern, not only about the potential legacy of closed operations, but also those mines that continue to operate.While mines across Australia are committed from the earliest planning stage to develop clearly defined post-mining land use and landform objectives, broader expectations related to these objectives may change and evolve during the life of the operation. This is especially the case where a mining operation has a project approval where the land use objectives are aligned to land capability and land use commensurate to that which occurred premining. CITATION:Murdoch, D and Purandare, J, 2016. Optimising land for beneficial use during and after mining, in Proceedings Life-of-Mine 2016 Conference, pp 166–167 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By M S. Tuohy

Poorly judged or under-appreciated change plays a role in many major accidents. In particular, operational changes related to continuous improvement, maintenance and introduction of new technology can lead to unintended safety (and other) consequences. This paper provides an overview of the role of management of change in preventing unwanted impacts on safety, community relationships and the environment. It draws on a range of incidents covering mining, minerals processing, refining and smelting where inadequately assessed or ineffectively implemented change led to significant safety, environmental or community consequences. The paper will also highlight cases of well-managed complex change and the underlying model of decision-making in place to make those decisions. All these examples are drawn from Atturra’s experience in response to accidents or working with sites to improve their management systems. The paper will report on the challenges of applying conventional risk assessment approaches to complex or technically significant change. These typically result in either onerous and lengthy change procedures that are prone to workarounds or poor implementation. Conversely, ‘light touch’ or efficiency driven change processes present the risk of intended consequences by failing to bring appropriate expertise to bear in decision-making. Such balances can be resolved by considering the designation of ‘technical authority’ with appropriate expertise to consider the change and deconflict any production, cost or schedule trade-offs. Finally, the paper will reflect on the key components of management of change systems in the context of major accidents, highlighting good practice in how they are implemented. This will consider the integration of existing corporate processes, risk management and organisational structures into management of change systems, not just the content of change forms and procedures.

Apr 16, 2024

By K W. Bian, Y M. Liu

Tongkuangyu Copper Mine is currently the only mine in China employing block caving. It comprises two large orebodies known as the No 4 orebody and the No 5 orebody. They are approximately 50° in dip angle, 80 to 240 m in width and 800–1000 m in strike length. The two orebodies are separated by a distance of 110–130 m. Production with block caving originally, ie Phase 1 project started at Tongkuangyu from the first undercut at a depth of 200–300 m below the ground surface and designated as Lift 810 m in late 1989 and has continued to the present. During the last 25 years Tongkuangyu has mined three lifts: Lifts 810 m, 690 m and 530 m. The previous two lifts utilised a slusher process with an annual designed production rate of 4 Mt. In this context the lift name represents the elevation of track haul level.The Tongkuangyu Phase 2 project serves for two lifts (ie Lift 530 m and 410 m) under the elevation of 690 m and the annual designed production rate is 6 Mt. Since the orebody is approximately 50° in dip angle, it is originally designed that production at Lift 530 m is comprised of one main extraction level and two auxiliary extraction levels in the footwall and undercutting is started from one end of the extraction footprint forward to another end, which is from north-east to south-west.Production at Lift 530 m started from March 2011 and reached to 6.39 Mt in 2013 and 6.9 Mt in 2014. Additionally, Tongkuangyu improved block caving processes and used modern mining equipment, which differ from the previous two lifts. Blastholes for undercutting and drawbell-preparation are now drilled using jumbos. The blasted ore is transferred to the underground crushing station via 10 t electric load-haul-dumps (LHDs) and then delivered to surface via a belt conveyor 3200 m long.Due to increasing ground pressure, a consequence of mining depth increase, stress abutment and inadequate support, significant damage occurred at the Tongkuangyu Copper Mine with production at Lift 530 m. This resulted in significant production delays and rehabilitation costs. A series of improvements have since been implemented including an advanced undercut sequence and increased ground support. All of these improvements have allowed Tongkuangyu to alleviate ground control issues, reduce operating costs and ensure safe production.CITATION:Liu, Y M and Bian, K W, 2016. Production at Lift 530 m of Tongkuangyu Copper Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M Tsai

Tube bundle gas monitoring systems have been used in the mining industry for over 50 years. The initial design was based on four individual gas analysers along with a series of solenoid valves, gas sample conditioning and flow control mechanisms to ensure the correct gas flow stream volume to the analyser. Simtars staff have identified flow control issues when providing operational support to coalmines on numerous occasions. The accuracy of the oxygen analysis is dependent on control of the gas flow to the analyser. Oxygen is one of the parameters used in calculating Graham’s ratio which is used for the detection of spontaneous combustion activity in coalmines. This paper will provide data which identifies the flow control issues by comparing mine site records for the two surface sample lines in the analyser room and the gas cage. Mine sites will be deidentified within the paper. The paper will discuss some of the changes that have been made in modern tube bundle systems and compare the change to the initial design specification developed by the UK National Coal Board, investigate possible operational impacts and provide a technical fix to solve the current flow issues being experienced at some mines.

Oct 12, 2022

Drilling underground can be a hazardous undertaking in many circumstances. Raiseboring and boxhole boring underground could form an integral part of the block caving production methodology and getting the right mix of technical capability, ergonomics and economical viability has been the goal of many machine manufacturers. With the introduction of the Terratec Universal Boring Machine concept, flexibility of raiseboring, downreaming and boxholing has been enhanced by the introduction of a single machine that will perform all three processes. In addition to its technical flexibility, additional safety features have been introduced that will eliminate many sources of injury by mechanising most of the operational procedures. Together with the one-man remote operation, this machine design addresses and solves many of the safety issues. This paper outlines the machine concept, details its safety features and shows the techno-economic advantages for use in the block caving environment. Block caving is a distinct caving method applied mostly to large massive orebodies because of the inherent low costs and high production capabilities. Areas of sufficient size are mined by undercutting so that the mass above will cave naturally. Extraction of the caved ore at the bottom of the ore column causes the caving action to continue upward until all of the ore above the undercut level is broken into sizes suitable for handling (Figure 1).

Jan 1, 2000

By C Tomlin, C Gimber

Historically, key closure risks have been studied during operations and then further assessed as cessation of mining approaches. Only in the past couple of decades or so has progressive rehabilitation and closure become an integral part of regulatory frameworks, sustainable mine planning and more recently, new project and development planning. It is now broadly accepted that the best closure outcomes occur when rehabilitation and closure are properly considered upfront, during the early stages of a mine development project and well before mining occurs. Increasingly, regulatory processes are requiring more diligence on early closure planning, often as part of the environmental impact assessment (EIA) and approvals process, rather than later in dedicated closure study phases. There is an opportunity to use the information generated during this phase to make better decisions on project selection, design, mining methodology and all other facets of the mining operation.

Aug 2, 2023

By D Bruce, D Cox

The main access decline at Carrapateena mine was excavated through two different underground aquifers. In these areas of decline, pressurised water finds the path of least resistance through the rock and into the excavation. In some locations the ground water would upwell underneath the roadway resulting in rapid deterioration of the running surface. The deterioration of the road was so rapid that the two areas of decline required significant roadworks every single shift or it would become impassable by mine traffic. With a full fleet of underground trucks hauling to the surface, managing these sections of roadway was impractical and unproductive. The site team resolved this issue by installing Roller Compacted Concrete (RCC) to the affected sections of decline. RCC is a specialist concrete product that is delivered to the site near dry and is installed using a grader and roller similar to road base. This product can be installed quickly and be trafficked within hours of installation, making it ideal for mines with single access declines and unfavourable road conditions. RCC roadways were successfully installed at Carrapateena mine in conjunction with under-road drainage. These roadways have proved to be a very effective solution which requires minimal maintenance and are resistant to water ingress from the aquifer. This paper discusses the technical aspects of the RCC, as well as the practical implementation of the solution as a whole.

Mar 15, 2021

By G I. Lumley

‘Every mine is a pilot’ is an attitude which encourages the mining paradox of optimistic mine plans and equipment under performance; propped up by an environment lacking accountability. The premise that ‘every mine is a pilot’, appears to underlie the development and operating approach to most mines. It is the hypothesis of this paper that many mining companies, development teams and their managers largely ignore what is done elsewhere. Anecdotally, most planners don’t know whether the selected rates are high or low (rates based on theoretical models tend to be high – certainly higher than what most companies can achieve). Mines then consistently operate the equipment at rates well below targets; often more than 20 per cent below. Further to this paradox, mine performance data demonstrates the average mine is currently operating their equipment at levels of output not much more than half the output of those in the top ten per cent. On the whole mines don’t know the potential of their equipment and therefore don’t put appropriate plans in place to do better. After all, when ‘every mine is a pilot’ there is little reason to look to one’s peers for an indication of potential. This paper will outline why every mine is not a pilot and how mines do value some knowledge, but not as much as they should. This paper proposes a two-pronged approach to address this issue in the area of equipment performance. This approach is to:1. engage in better forecasting of equipment rates and better subsequent performance through benchmarking against industry standards2. provide conditions for more accountability.These parameters are linked and proper implementation of them will address the losses which many shareholders and financiers have incurred when investing in companies with unrealistic mining plans.CITATION:Lumley, G I, 2016. Is every mine a pilot? In Proceedings International Mine Management Conference, pp 75-88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

Two characteristics of the modern mining industry are that there is a skill shortage and that young professional people rise rapidly into highly responsible supervisory positions. With this responsibility comes the burden of identifying and managing health and safety risks. Without the benefit of a comprehensive health and safety training program, these young professionals may be putting both themselves and those under their supervision at risk. The Moura Mine explosions and the asbestos health disaster should not be just artifacts of history, but highly valued lessons that impress the need for comprehensive health and safety risk management strategies on young professionals. From the perspective of the former secretary of the Committee to implement the findings of the Moura (Disaster) Inquiry and as the former coordinator of the Coal Workers Health Scheme, key issues in occupational health and safety management systems are explored.

Jan 1, 2005

By S Grobler, T Fares

Understanding the real utilisation of the available volumetric capacity of a conveyor is key to unlocking latent capacity or ‘debottlenecking’ existing plant. Conveyors are typically designed on the basis of conservative density and ore surcharge angle specifications, and consequently there is often latent volumetric capacity available.Laser scanning measurements of conveyor ore profiles has been undertaken on iron ore conveyors to gain an understanding of the actual surcharge angle and the available edge clearances. Iron ore producers seeking to extract maximum production from their assets have used these measurements to debottleneck existing plant and to revise the design criteria for future plant. The benefit is that latent capacity of existing plant can be unlocked and smaller and cheaper conveyors can be designed for future plant, maximising the return on capital. This paper describes the measurements and results.CITATION:Fares, T and Grobler, S, 2015. Laser scanning of conveyor ore profiles, in Proceedings Iron Ore 2015, pp 549–554 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015