Search Documents

By P N. Holtham

Magnetic separation is routinely used in the processing of titanium minerals, and the efficiency of these operations can be determined by measuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved. This paper describes the development of an inductance-based instrument for measuring very low levels of magnetic susceptibility on-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance. A prototype instrument has been installed in the zircon scavenger circuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction. Using the instrument, the zircon content of this stream can now be accurately determined from the measured magnetic susceptibility, provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

As a result of cheap Maui gas and plentiful hydro-electricity, over the past few decades New Zealand has enjoyed some of the cheapest energy of any OECD country. The situation is changing; at best we are facing some radical changes in energy use, at worst we are facing a crisis resulting from the following:   Cause 1: Maui gas will be exhausted by 2012. Distorted pricing and supply contracts; resulted in Huntly Power Station, a coal mine mouth generator running on 70 per cent Maui gas until very recently!   Cause 2: Investment in new generating capacity (and transmission) is woefully inadequate; as a result hydro lake levels are being continually pushed to the limits.   Cause 3: Distorted thinking is everywhere, for example; æWe will find more cheap gasÆ. æGas is clean û coal is dirtyÆ. Hot air  û ægreen alternatives such as wind generation will save usÆ. æNo NuclearÆ. The outcomes of the distorted thinking will be price increases, then shortages (there is nothing like "black-outs" to focus national thinking) and finally recession.   But what can NZ do? - Mine Coal. Coal jump-started the industrial revolution, it can provide the transition to post-gas and oil. NZ has the second highest reserves of coal per capita in the world, yet we use less that any other country with significant coal reserves. Our exports of our best coal have increased threefold, yet out own consumption has remained static at about 1-1.5 Mtpa for the last 30 years. Our coal is NZ owned and inexpensive relative to other energy sources, even allowing for infrastructure and environmental costs.   What can we do? We as mining professionals can promote informed responsible development and investment in the country's mining and energy business. We can galvanise public opinion on issues such as æunbundlingÆ our entire energy chain from mine-to generator-through transmission, even if the nuclear issue has to wait! With oil above US$70/bbl substitution is feasible. For individuals, there is always solar!

Jan 1, 2006

By S M. Denn

The Cawse nickel-cobalt operation is situated 50 km NW of Kalgoorlie in Western Australia, at latitude30o22'30'' south and longitude 121o08'30'' east on the Kalgoorlie 1:250 000 geological map sheet (SH 51-9) (see Figure 1). The project is owned and operated by Centaur Nickel Pty Ltd (CTR) and was the first in Australia to commercially produce nickel metal and cobalt sulphide through pressure acid leach (PAL) technology. Cawse has a total resource base (all categories of resources + reserves) of 213 million tonnes Mt at 0.7 per cent Ni and 0.04 per cent Co, comprising 127 Mt at Cawse Central which is 100 per cent owned by CTR and 86 Mt at Cawse Extended where CTR has a 80 per cent equity. Cawse Extended is located immediately to the northwest of the Cawse Central leases. All current reserves (proved and probable) of 30 Mt at 1.0 per cent nickel are contained within Cawse Central. In addition the Siberia project area 20 kilometres to the NW has a resource of 63 Mt at 0.7 per cent Ni. Cawse is a dry laterite deposit, with nickel and cobalt hosted by iron and manganese oxides. Cawse Central mineralisation extends over a ten kilometre strike length, with three pits currently being mined. The Bunyip pit has the premier nickel and cobalt grades within Cawse Central. There are seven dominant lithology types forming mappable units within current pit exposures. Four of these units are host to nickel and cobalt mineralisation. Ore types are defined as Upgrade, Grind and Non-upgrade, depending on their physical characteristics with respect to the treatment route. Mining commenced in February 1998. To the end of calender 1999 the operation has produced 2100 tonnes nickel plate and 470 tonnes of cobalt as a cobalt sulphide product. Future production will target 9000 tonnes per annum Ni metal and up to 2000 tonnes per annum Co, based on processing 500 000 tonnes of ore per annum.

Jan 1, 2000

Hindered settling devices (teeter bed, up-current) are widely used in the mining industry to classify mineral streams into various size fractions and to separate minerals. In the coal industry these devices are extremely successful in separating coal of low densities from shale and pyrite. In the beach sand and in the iron ore industry, this equipment is used to beneficiate minerals either as stand alone units or lately as classifiers in spiral circuits. The challenge that these applications give to metallurgists is to be able to simulate the equipment by using mathematical models with or without the aid of small bench scale tests. In any green fields and many brownfields projects, limited amounts of samples make pilot plant tests difficult. Although there are mathematical approaches available, the accuracy is of such a nature that it can not be used for design purposes. This refers to the use of StrokeÆs law, NewtonÆs and the so called intermediate law as is widely published. Research done by the author indicates that in most applications none of the above laws apply. Using the original data as published by Perry and Chilton (Chemical Engineering Handbook, pp 5-64, 1973) and re-plotting it indicates that the settling velocity of particles is a function of (particle diameter)n where n varies between 1.2 and 1.6 which is different from that predicted by the intermediate law that suggests that n = 1.18. Another way of describing the relationship between the drag force and the Reynolds number is done by iterating between settling velocity and the Reynolds number. This needs more computer time but the accuracy obtained from this does add value to simulations. A small but simple test is suggested to determine the settling velocity of particles to enable metallurgists to determine variations from the theoretical calculations to determine the influence of viscosity and particle shape.

Jan 1, 2008

By Quast K. B

The ore used in this test program was a composite sample from Waihi, New Zealand containing 2.7 g/t gold and 36 g/t silver. From the testwork it was found that a high concentration of sodium cyanide (0.1 per cent) was necessary to ensure a high recovery of both gold and silver. There appeared little chance for either differential leaching or adsorption of gold and silver. The addition of bentonite clay decreased the rates of gold and silver dissolution. The addition of 50 g/1 NaCI had little influence on the rate of silver extraction. The addition of 5 g/l carbon gave adsorptions of 70 per cent of the gold and 35 per cent of the silver, indicating the possible presence of base metal cyanides in solution. The addition of excess sodium sulphide only precipitated 70 per cent of the silver in solution, adding further evidence to the presence of base metal sulphides. The production of separate silver and gold products was not possible by either preferential leaching, preferential adsorption of gold on carbon or preferential precipitation of silver.

Jan 1, 1991

By Moy A. D

The Esperanza deposit is located 120 kin N of Mount Isa, Queensland at approximately lat 19¦20'S, long 139¦22'E on the Camooweal (SE 54-13) 1:250 000 scale map sheet. It is one of several structurally controlled copper ¦ cobalt deposits developed along the Mount Gordon Fault zone and related faults, within the Western Fold Belt of the Mount Isa Inlier (Figure 1). Together with the nearby Mammoth orebodies it forms the basis of the Gunpowder operation of Aberfoyle Limited. Until recently ore was mined from the Mammoth orebodies by open stoping with decline haulage to surface leach pads. Leaching of in situ broken ore (in place) and surface heaps, followed by solvent extraction and electro-winning (SX-EW), produced copper metal on-site. In March 1997, mining was suspended at Mammoth and the focus of the Gunpowder operation switched to development of the Esperanza orebody, which is expected to begin open cut production in mid 1998. SX-EW methods will produce 44 000 tpa of copper from an expanded plant. The pre-mining mineral resource at Esperanza (measured, indicated and inferred) is estimated at 4.6 Mt averaging 7.7 per cent copper.

Jan 1, 1997

By H Zhang, S Li, J Song, Z Lv

In this paper, a method for extracting and refining metallic molybdenum using low-temperature ZnCl2- NaCl-KCl molten salt was proposed. The electrochemical behaviour of molybdenum ions in ZnCl2- NaCl-KCl molten salt was investigated in detail, and pure metallic molybdenum was collected on the cathode. The reduction and diffusion processes of Mo(V) ions in ZnCl2-NaCl-KCl molten salt were determined through a series of electrochemical methods. The diffusion coefficients and nucleation modes of Mo(V) ions were also studied, and electrolysis was conducted for a prolonged period at a constant current density. The results indicated that the electrode reduction of Mo(V) ions in ZnCl2- NaCl-KCl molten salt proceeds through a three-step reaction: Mo(V) → Mo(IV) → Mo(III) → Mo at 250°C. The Mo(V) → Mo(IV) reaction was reversible and diffusion-controlled, with a Mo(V) diffusion coefficient of 6.02 × 10-6 cm2 s-1. Additionally, the nucleation mode of Mo(V) ions was instantaneous nucleation. The products electro-deposited were confirmed of metallic molybdenum with a particle size of less than 1 μm.

Aug 21, 2024

The accurate determination of trace level gold in ores, metallurgical samples and process solutions is required because of the value of gold, the efficiency of the cyanide leach process and because of the high gold recovery from these cyanide solutions. It is thus necessary to routinely analyse geological and metallurgical samples with gold concentrations of 3 g tonne (ug g- 1ppm) and process solutions with a gold concentration of 0.01 mgL 1 (ppm) preferably with sufficient accuracy to quote at least two significant figures. Several techniques have been reviewed for their suitability for the routine gold analysis of these samples which also contain signif- icant concentrations of other ions. The classic fire assay technique has achieved the respect and confidence of mining personnel because of the results achieved by very experienced assayers. Other extraction and concentration techniques have now been shown to be equally effective. The use of instrumental analytical techniques particularly atomic absorption spectrometry have shown that cheaper procedures, which are as reliable, are now available to gold producers for the routine analysis required to maintain an efficient gold recovery process.

Jan 1, 1982

The use of coal as a fuel for heat and power generation has a long history. During the nineteenth century most of the present combus- tion technologies were pioneered, as shown in Table 1, This period was associated with the "golden age" of coal and its contribution of almost 80% of the world's energy demands in the early,1900s . The decline in the use of coal has been due to the transfer of the heavy transportation area to diesel power, the elimination of coal as a household fuel and the substitution of oil for coal in power plants. Coal remains the major fuel for the electric utility industry and the present paper will be concerned primarily with that application. Table 1 outlines the development of coal tech- nology with the parallel understanding of coal as a material and its behaviour during combus- tion. Clearly many developments in combustion technology have occurred in this century, although most of the processes had been invented in the nineteenth century. Also, the great expanse in coal research of the past few decades has led to a greater understanding of the coal combustion process.

Jan 1, 1987

By Davey CJ

An integrated computer software system has been developed by Fluor Australia for modelling, mine planning and production scheduling of single or multi-strata deposits. Modelling of both quantitative and qualitative variables (e.g., thickness, basal elevation, density, grade/ash content) is performed via continuous, minimum curvature surface representations. These may be developed from inverse distance weighting or geostatistical kriging interpolation techniques in conjunction with bicubic spline surface interpolation. The modelling process, rather than being purely mathematical, incorporates facilities for reflecting structural geology interpretations (e.g., faulting, pinchouts) and geological boundary conditions (e.g., subcrop and outcrop). Volumetric programs provide the facility for continuous integration over models (at any specified integration increment) for any number of specified irregular polygonal panel areas or regular rectilinearly defined block plan areas. Multi-variable integration is available, incorporating any or all operations of addition, subtraction, multiplication and division to provide multi-strata tonnages, etc., (e.g., Volume 1 * density 1 + Volume 2 density 2). These programs provide true three-dimensional integration with the facility for calculating results on an area by area, level by level, strata by strata as well as overall basis.

Jan 1, 1983

The Nagambie heap leach gold mine commenced production of gold in September, 1989. The mine,120km north of Melbourne in Victoria, Australia, was developed by Perseverance Mining Cor- poration Ltd, a junior Australian mining company, with no other operating mines. Gold production to December 31, 1990 was 47,621 oz. The mine is now producing at the rate of about 45,000 oz per year. As of February 28, 1991, resources at the mine are 5.1 million tonnes measured, at 0.65g/t Au while reserves were 1.65 million tonnes at 0.86g/t Au of proven, heap leach ore, plus 0.37 million tonnes at 0.40g/t Au, of dump leach ore. Metallurgical recoveries expected are 80 per cent for the heap ore and 60 per cent for the dump ore. Perseverance Mining Corporation was listed on the Australian Stock Exchange on April 2, 1987, after a capital raising in March that year. At this time the company's issued capital was 4 million ordinary 25ó shares, 3 million of which were issued to the public to raise $0.75 million.

Jan 1, 1991

By J Wei, X Lan, F Wang

This paper presents a quantitative assessment model for the assessment of environmental load in gold production, which is based on environmental ecology, Life Cycle Assessment (LCA) and artificial neural network. In LCA evaluation indexes include resource consumption, energy consumption, gas waste, liquid waste, solid waste and so on. Each item represents an aspect in gold production while their combination reflects the relationship between gold production and environment. In this paper an utility function of evolution index on environmental load is given by linear or non-linear transformation, which changes evaluation indexes with different dimension into an equivalent value in range of [-1, 1]. This paper also provides a new approach to make decision on the weight for quantitative assessment with the help of a three-layered artificial neural network. The proposed approach in this paper has been successfully used to a real synthetic assessment for the environmental load in gold production, which include seven kinds of different operational technologies in China. The applications prove that the new approach is successful and reliable. It provides a new tool for the assessment of environmental load of the gold production.

Jan 1, 2003

By Tapp B. A

To date, few studies have been made regarding the energy requirements of the Australian mining and mineral processing industries. This paper indicates that these industries use a substantial proportion of the total Australian energy input (32.7% in 1971-72 and 36.10% in 1974-75). With the growth orientation of these industries, this input is likely to increase. Data shows that mining energy requirementE varied from 4.22% (of total Australian energy requirements) in 1971-72 to 4.16% in 1974-75. Energy requirements for the total mineral processing industries increased from 28.49% to 31.93% for the same period. The total estimated primary energy input varied from 22.56% to 25.2%, whilst indirect energy use, in the form of electricity increased from 10.16% to 10.66%; in the same period. Analysis of primary energy input data within the processing industries (1973/4) showed that the Iron and Steel Industry consumed 15.03% of the Australian total consumption, Non-Ferrous metals, 5.43%, Cement, 1.64%, and Refractories, 1.59%. In toto this represented 24.57% of the total

Jan 1, 1979

By Clifford C. E

1 eat my peas with honey I've done it all my lifeIt makes them taste rather funny But it keeps them on the knife.Innovation is that elusive characteristic which involves the determination of multiple and unique response to a problem, and then commitment to and action from the best of the alternatives.

Jan 1, 1993

By McBride N

Location The Boddington Gold Mine (BGM) is located approximately 120 km south east of Perth, Western Australia. (Figure 1). Located within the picturesque Darling Ranges, the land was previously used for forestry activities prior to mining commencing in mid-1987. Mineralisation is hosted within deeply weathered felsic and intermediate intrusions and volcanic rocks of the Saddleback Greenstone Belt.

Jan 1, 1995

By Langberg D, Gray N. B

The flocculation of hydrophobic magnetite with gold was examined as a possible means of recovering fine (95 per cent were possible for 1.5 - 3.0 ¦m and 5.5 - 7.5 pm gold sizes. The effect of process variables on the flocculation process was explained by variations in the adhesive force between the gold and magnetite.

Jan 1, 1991

By L R. B M Sß

This paper presents the results of a liberation study made on a sulfide copper ore from Carajßs, Brazil, in a mini pilot plant flotation test. The aim of the research was the methodological evaluation of a liberation study using a sample crushed at 1 mm and a sample ground for flotation testing to a target size of 80 per cent

Jan 1, 2005

By Singh RN

The Bulli Coal Seam, located in the Illawarra Coalfield of New South Wales, has a long and varied history of sudden outbursts. From available information this problem has resulted in twelve fatalities over the last one hundred and one years, with over five hundred separate outburst incidents being identified. These incidents have varied in severity and intensity from the discharge of 1 to 2 tonne of coal, with a slight increase in gas emission, to the discharge of 200 to 400 tonne of coal with some 6,000 m3 of gas being liberated and large items of mining equipment being pushed 1 to 2 metres down the roadway.Geological features associated with these outbursts can be mapped on a regional and mine by mine basis, to provide some indication or warning. Similarly changes in gas content and gas composition can also be determined on a regional and mine by mine basis. However sudden geological changes (such as a 6.5 metre seam displacement within 15 metres) variations in gas content (such as 6 m3/tonne to 15 m3/tonne) and changes in gas composition (from 95% CH4 to 90% CO2) all within one mine does make the prediction or forecasting of outburst incidents exceedingly difficult.

Jan 1, 1998

By Wilkinson RDB, Van Der Meer FP

In order to overcome the statistical limitations imposed by the need to recover density tracers by hand, magnetic density tracers were developed to determine the efficiency of dense medium separators treating porous materials. The tracers were manufactured by extrusion of polypropylene ferrosilicon mixtures and subsequently coated with a distinctive paint to allow hand sorting according to density. Fifteen tracer batches were manufactured in the range 1.61 - 1.94 g/cm3. The tracer densities were determined by a hydrostatic method. The tracer method was applied to the dense medium separation of a Moroccan oil shale in a pilot scale Dyna Whirlpool separator. For each test, about 20,000 tracers were added with the plant feed and subsequently recovered from the products with a dry low intensity magnetic separator. The Tromp curve determined by conventional heavy liquid analysis was displaced towards lower densities compared with that determined by tracers, indicating that the porous shale particles absorb heavy liquid. It is concluded that for porous materials like oil shale and coal, the tracer method gives the most accurate results. In pilot scale testwork the tracer method is also much faster than the conventional heavy liquid analysis, as rather large samples have to be processed by the latter method to ensure Representativeness.

Jan 1, 1987

Routine, in-pit geological mapping of highwall at Central Queensland Coal Associates (C.O.C.A.) deep strip mines has proved too slow for the increasingly greater highwall lengths which require mapping. This realiz- ation has encouraged the search for faster mapping methods and after trial of ground photographic methods has resulted in the adoption of interpretive mapping off stereo cover, oblique -- aerial photography. This entails using a Cessna 182 light aircraft flying at its slowest speed, the aerial meth- od finally employed consisting of two Vinten, air reconnaissance cameras mounted in parallel and simultaneously taking both colour and black and white photographs of the mine high- wall. The respective 1:500 scale enlargements produced from the 70mm format films combine to present the sharpest resolution attainable under the field conditions pertaining and such information on weathered material as only colour photography can fully render. Total costs for the aerial photography method are estimated to be about the same as those for conventional in-pit mapping. Whilst total costs are comparable, geo- logist's time for mapping a 10 km. length is reduced to less than half that for in-pit mapping (for Stage 1, fully accurate mapping) and accuracy and detail are greatly improved. A permanent, accurate record of overburden

Jan 1, 1981