Search Documents

The subject of heat sources in deep hard rock mines, the limitation of forced ventilation to cope with these heat loads and the sizing of refrigeration plants to boost the cooling effect of the ventilation air are discussed. The development of plant selection criteria and operating experience at North Broken Hill Limited is outlined. Future options for North Broken Hill Limited and like deep mines are summarised.

Jan 1, 1982

By Y Gu

Based on the mode of occurrence, gold is classified into three categories: microscopic gold, submicroscopic gold and surface-bound gold. Microscopic gold, or visible gold, refers to gold minerals in which Au occurs in a substantial amount, such as native gold and electrum. Submicroscopic gold, ie invisible gold, refers to gold contained in the structure of other minerals (mainly sulfides) in minor to trace amounts. Surface gold is the gold that was adsorbed onto the surface of other minerals during mineralisation and subsequent oxidation or metallurgical processing. Gold mineralogy has a significant impact on its extractive metallurgy. Gold process mineralogy helps address problems related to gold ore processing. It is widely used as a predictive and troubleshooting tool in gold ore processing, and provides useful information on process selection, flow sheet development, recovery improvement and reagent consumption optimisation. This paper will begin with the classification of gold ores, and will focus on gold mineralogy and how it impacts extractive metallurgy through case studies.

Jan 1, 2008

By Singh T, Singh D. P

India has limited resources of coking coal. Most of the coking coal seams are located in Jharia Coalfield. These seams were worked in the past by the bord and pillar system in a haphazard manner, which has resulted in honeycombs of old working. Most of such areas are under fire. In order to meet the demand of coking coal in the 21st century, it is essential that the coal locked due to old underground workings is recovered fully by conducting opencast mining to an ultimate depth of 500 m. The major problem envisaged in conducting opencast mining in such areas will be the stability of pit slopes over voids and the behaviour of subsided material in the pit slopes. An attempt has been made to simulate this complex situation from a specific section of the rockmass of a mine in an equivalent material (EM) model. The old workings existing in upper coal seam (V) were simulated by developing staggered bord and pillar workings in two sections and depillaring them. Opencast mining was conducted for recovery of coal locked due to irregular working in coal seam V. The slope instability caused by intersection of the slope with the void, during frontal working (by shovel-dumper combination) was observed in various situations. In this paper, the technique adopted for simulation of a 125 m thick section of rockmass in an EM model is outlined. Adverse effects of staggered workings and

Jan 1, 1988

By Munro DL

The Mary Kathleen uranium deposit is in north-west Queensland, approximately halfway between the townships of Mount Isa and Cloncurry, at long. 1400 009 E and lat. 200 44' S. The deposit Iwas discovered by prospectors of the Walton McConachy Syndicate early in July, 1954, and climaxed a very intensive ground search by hundreds of part-time prospectors. during the uranium boom from March to July 1954ò Numerous small deposits, mostly in the vicinity of Mount Isa, were discovered in various rock environments, but Mary Kathleen is the only large deposit and, apart from a few tons of hand sorted material from the Milo lease, is the only deposit that has been worked. Exploration of the surrounding area, and proving of the economic worth of the deposit, were conducted from the time of discovery until February 1956 by a geological team camped near the deposit. Proving was carried out by drilling a pattern of vertical and inclined diamond drillholes at fifty-foot centres over the outcrop. An adit was driven eastwards through the deposit. Metallurgical research and design work in the South Australian Department of Mines Adelaide Laboratories were based on core samples and bulk samples from the deposit. The signing of a contract in March 1956 with the British Atomic Energy Authority to supply 4500 short tons of uranium oxide allowed mining to commence, and enabled the planned construction of water supply, township and treatment plant to proceed. The open out mine and plant are now serviced by a modern township, four miles away, which is connected to Cloncurry and Mount Isa by road. Although little field work has been done since the exploration phase, this paper differs in interpretation from a previous paper (Matheson and Searl, 1956) in that it is based on a revised structural inter- pretation (Compana, 1958), detailed mapping of progressive exposures in the open out, and a re-examination of diamond drill cores.\

Jan 1, 1968

Gold mineralisation at the Macraes Gold Project is hosted in the Hyde-Macraes shear zone and can be traced for ~30km along strike, although economic resources are confined to a 7 km section in the vicinity of the Macraes township. The shear zone, which typically dips at a low angle (~20 o ) to the NE, is bounded by an upper hanging wall shear and a lower footwall fault. Mineralisation occurs along the hangingwall of the shear zone as well as in low angle concordant shears and stockworks. Ore types include graphitic cataclasites with variable amounts of quartz veining, ælode schistsÆ and quartz-vein stockworks. Rehabilitation at the mine has focused on creating an environmentally benign site dominated by pasture to allow continuation of the traditional pre-mine farming economy. Changing regional economics, continued urbanisation and a reduction in traditional employment opportunities has seen a rethink in the long-term rehabilitation outcomes. The community has recognised that the rehabilitated site will provide the basis of a viable tourism venture and the creation of a Heritage and Art Park (working title æGolden Point ParkÆ) is the culmination of that process.

Jan 1, 2002

By Fleming GJ

The Miwah prospect lies on the dilational 070¦ trending Miwah Lineament near its intersection with northerly oriented fractures within Pliocene volcanic rocks exposed between a NW trending segment of the dextral transcurrent Sumatra Fault, and the more northerly trending Samalanga-Sipopok Fault to the east. These faults reflect the continued interaction between stresses from the India-Australia plate located to the southwest, and spreading within the Andaman Sea to the north of Sumatra. A system of deep seated faults is believed to have facilitated emplacement of post-Miocene magmas and Quaternary volcanic centres at shallow crustal levels throughout northern Sumatra.

Jan 1, 1995

Leichhardt Colliery is developed for underground mining of coal seams at depths exceeding 280 m. Investigations of the area were conducted in phases, each designed to delineate seam characteristics more accurately and to indicate with increasing precision the nature of local geological features and the ranges of those coal properties susceptible to variation. The investigational campaign is described phase by phase summarizing evaluation of the area at the conclusion of each phase. Predictions of geological conditions likely to influence engineering planning are contrasted with actual conditions observed during trial mining.

Jan 1, 1974

By Agrawal A, Joshi A

Mochia mine, in culmination of depillaring operations, fired India's largest underground pillar blast consuming 145 tonnes of explosive and yielding 0.55 million tonnes of ore in June 1994. To protect main mine structures (situated at a distance of 250 to 350 m from the blast site) from resultant ground vibrations, the charge per delay was restricted to 2300 kg. The post-blast observations revealed that no damage was caused to these structures. However, the damage assessment survey of the mine workings situated in close proximity revealed a general trend in consonance with the distance from the blast and found to be well correlated with peak particle velocity.

Jan 1, 1995

By E E. Hall, S, E D. Thimons, R J. Timko

The heart of mine ventilation science and technology is the protection of the life and health of the miner. Lung diseases that result from overexposure to various mine aerosols can largely be prevented by maintaining concentrations below prescribed limits. Maintaining safe aerosol concentrations depends, in part, on our ability to know what mine aerosol concentrations are in a timely and accurate way. The Centers for Disease Control and Prevention (CDC), National Institute for Occupational Safety and Health (NIOSH) has been developing several new tools to help miners monitor respirable coal dust, silica and diesel particulate matter. This paper will discuss three main topics. First, the latest results of the person wearable dust monitor (PDM), developed by Rupprecht and Patashnick under CDC contract. The PDM was tested side-by-side with conventional samplers at a number of US coal mines and results indicated that the PDM was comparable to conventional samplers. Second, improvements to the dust dosimeter monitoring technique that includes a new pump with built-in pressure transducer and algorithm to convert differential pressure to dust concentration have shown good precision. Third, advances in the use of the detector tube technique to monitor tailpipe diesel emissions and ambient diesel particulate matter show that strong correlations exist between differential pressure measurement and elemental carbon in the samples.

Jan 1, 2005

The metallogenic belts of the Central Andes (iron, porphyry copper, polymetallic and tin) are genetically related to an eastward migrating magmatic arc. The polymetallic belt of the Bolivian Altiplano formed during Miocene arc broadening and lies in a critical position for understanding the genesis of this zonation. It is penecontemporaneous with parts of the copper and tin belts, and shares many characteristics with them. The differences between the belts result from contrasting volcanic and feeder stock geometry, depth of erosion and country rocks, and are not due to variations in magma chemistry, age or Benioff Zone depth. Polymetallic mineralisation in the Altiplano is epithermal in style and mostly related to flow-dome volcanism. The intermontane basinal setting precludes deep erosion to expose the epizonal feeder stocks and predicted porphyry copper mineralisation. In contrast, erosion of the less abundant stratovolcanoes of the Altiplano-Puna and Pampean Massif may expose contemporaneous Miocene porphyry copper mineralisation in subvolcanic stocks. The tin belt is coincident with the Paleozoic fold belt of the Eastern Cordillera. The occurrence of minor tin in Altiplano epithermal deposits hosted by Paleozoic sediments, and the persistence of tin mineralisation in the tin belt over 350Ma, suggests that Paleozoic sediments are the source of the tin.

Jan 1, 1987

With some notable exceptions, marine placers located just below, or just above, present sea level, are responsible for much of today's production of detrital ilmenite, rutile, zircon, and other minerals of value. The purpose of this paper is to discuss the paleogeographic and paleo-oceanographic factors which may have determined the location of presently submerged marine placers. These factors-include changes in sea level, burial by recent marine sediments, stream capture and other i changes in drainage patterns, and recent changes in climate. Selected geologic situations in the Yellow Sea off the coast of Korea, in the Atlantic Ocean off the coast of Portugal, in the Bering Sea off the coast of Alaska, and in the Arabian Sea off the coast of India, will be used to illustrate the author's point of view.

Jan 1, 1980

British Coal has made a practical progressive approach to improving the reliability of its mining equipment. Reliability must be addressed at the specification stage but does not end there and routine procedures are used to procure equipment of adequate reliability. The techniques used to monitor and improve reliability during the operational phase of the equipment, providing engineers and operators with detailed printouts, together with the types of maintenance employed, ensure high levels of availability. Finally, the methods of repair and overhaul of British Coal equipment and systems ensure that the initial reliability targets outlined on the specification, can still be achieved.

Jan 1, 1991

By D Cotnoir, Q Liu, D Richard, M Ourriban

The difficulty in fine particle flotation has been attributed, among other things, to a low bubble-particle collision efficiency. Many technologies have been developed which aim at increasing bubble-particle collision efficiency, either by generating micro bubbles or by enlarging particle sizes. However, commercial applications of these technologies are limited. Over the last five years COREM has been actively testing fine particle froth flotation technologies with the objective of commercialisation. Several fine particle flotation technologies, such as dissolved air flotation, electro-flotation, floc flotation, selective flocculation-flotation and carrier flotation, were tested on both single minerals and ore samples in order to identify the reasons that prevented these technologies from being used on a commercial scale. It was found that the two most noticeable factors that prevented the successful application of these technologies were: Mechanical entrainment of fine gangue minerals. This was a general problem in fine particle flotation, but was aggravated by these technologies that either generated micro bubbles or enlarged the sizes of hydrophobic particles. Oxidation of (sulfide) minerals that resulted in hydrophilic oxidation product coatings. The oxidised fine particles could not be recovered by these fine particle flotation technologies effectively. Solutions to the two problems, ie gangue entrainment and fine particle oxidation, were proposed and tested. It seems that polymeric depressants with both depression and flocculation functions could significantly reduce gangue entrainment, and hydrophilic surfaces of oxidised fine particles could be modified by high intensity conditioning or controlled sulfidisation, thus increasing the recoveries of fine valuable minerals. The improved fine valuable particle flotation and reduced fine gangue entrainment along with fine particle flotation technologies resulted in much improved flotation separation of fine particles.

Jan 1, 2005

Nickel WestÆs Kalgoorlie Nickel Smelter operates three Peirce-Smith converters, each processing 110 tonnes of matte per charge. The vessels are lined with chrome-magnesia refractory with a mouth traditionally constructed from steel liner plates, protected with cast refractory. Mouth refractory is damaged by molten material and the action of cleaning solid buildup off the mouth. Once damage has accumulated, the mouth must be frequently maintained with hot refractory gunning or a mouth leak may occur. Such a leak requires a 32 hour repair period. A converter mouth redesign program was undertaken with the aim of reducing the rate of mouth damage during operation, eliminating mouth leaks and shortening mouth replacement times during vessel rebuild periods. An overview of the redesign process and operational performance is contained herein.

Jan 1, 2005

Over the last five years Du Pont (Australia) Ltd has developed a commercial range of new generation emulsion based explosives concurrently with the development of new explosives-placement systems. The paper outlines Du Pont's emulsion technology and history of product development from the initial emulsions (Tovex E & EL) to emulsion/ANFO blends (Tovex BE) through to the most recent development of Du Pont's SOL emulsion component. The paper also outlines the development of materials handling systems on site to load waterproof bulk explosives from the original pumper trucks through to the multipurpose agitator bowl blending and pumping units at the heart of Du Pont's SOL emulsion system currently available within Australia. The last section deals with some of the more important features of enhanced agitator bowl truck designs and outlines examples of the complete SOL emulsion system and methods of operations currently practiced at specific mines within the Bowen Basin coalfields.

Jan 1, 1986

By C Quirion

Agnico-Eagle Mines Limited, Laronde Division, operates the deepest single-lift shaft in the western hemisphere. The initial Penna hoisting plant was designed for a production rate of 1800 tonnes per day (t/d) from a 2240 m deep shaft. Exploration success, while sinking the shaft, led to a decision in 1998 to increase the production rate to 4500 t/d of ore from a loading depth of 2200 m. The new production rate was achieved by increasing the size of the rope and reducing the rope static factor from the existing 5.0 required by regulation to a static factor using the formula 25 000/(4000 + L) contained in a draft document that would eventually become SABS 0294 in South Africa. The formula permits Laronde to use a static factor as low as 4.0. The upgraded Penna hoisting system is the first hoisting plant outside of South Africa to meet the South African requirements. This paper describes the conversion of the hoisting plant to the lower rope selection factor in the year 2000 and the operating and maintenance issues experienced since then.

Jan 1, 2005

By B Washington, A Campbell, R Taylor

A sampling and measurement program was undertaken on the reaction shaft of the Olympic Dam copper flash smelting furnace. The object of the work was to provide information to validate a mathematical model of the burner and reaction shaft. Samples and measurements were undertaken through the burner inspection ports and the South East (SE) shaft sampling port about half way down the reaction shaft. Samples were collected to enable the calculation of particle loading of shaft gases, or sizing and chemical analysis of the partly-combusted feed, and the preparation of polished sections. Measurements were made of the temperature and sulfur dioxide content of the atmosphere, as well as plume velocity.To implement the program it was necessary to design and construct the following specialised items of equipment. For use at the burner inspection ports: a cup sampler for obtaining samples below the burners (temperature, solids loading and samples for characterisation).For use at the SE shaft sampling port and also at the settler level: trough sampler (plume definition and samples), isokinetic sampler (used as a velocity probe in this work), temperature probe (temperature traverses across the shaft), and sulfur dioxide probe (SO2 measurements across the shaft).The design of the sampling and measuring equipment is described, and examples are cited of the types of information obtained. The problems arising from working in a hot environment with molten or sticky particles are discussed.

Jan 1, 2005

By S C. Bhowmik, R Gupta

This paper presents the ventilation problem faced by Jaduguda uranium mine, operated up to a depth of 905 m. The first two stages of the mine workings are up to 555 m, which are nearly exhausted. The third stage of the mine is from 555 m to 905 m and presently most of the stopping and development activities of the mine are carried out in the third stage. The total available intake quantity in the third stage was only 21 m3/s. As a result, the mine was facing a radiation hazard. The different instruments and the methods used for monitoring of radiation levels are also presented in the paper. It was observed that the average individual effective dose (external + internal) of radiation workers in Jaduguda mine increased from 6.93 mSv/y in 1995 to 9.5 mSv/y in 2001 and during this period the average individual effective dose of mine workers of the world was less than 5 mSv/y. Keeping this problem in view, a detailed ventilation investigation has been carried out in this mine. Initially the requirements of intake air quantity have been assessed by carrying out field investigation in different stopes and it was found that the third stage workings require nearly 100 m3/s. A detailed ventilation survey has been carried out in the total ventilation network and a basic ventilation model of the mine has been prepared. Different alternative schemes for effectively ventilating the third stage workings of the mine were simulated and a set of recommendations were made for implementation. The recommendations were partially implemented in 2002. As a result the total intake quantity to third stage workings increased to nearly 70 m3/s and the average individual effective dose (internal + external) of mine workers came down from 9.5 mSv/y in 2001 to 6.65 mSv/y and 6.60 mSv/y in 2002 and 2003 respectively. The implementation of remaining recommendations is in progress. Finally, a mathematical model has been formulated from the first principle for predicting air quantity requirements in cut and fill stopes in uranium mines and this model is being validated for further use.

Jan 1, 2005

The proximity of the Town of Kalgoorlie to the Mount Charlotte mine necessitates that charge weight per delay be limited in order to keep surface vibration levels within acceptable limits and to reduce damage to underground workings. The mining system requires that large mass blasts must be used to recover pillars and therefore a large number of separate delays are needed. Until recently all blasting has been done electrically, fired from mains, but with the introduction of large diameter blastholes (165mm diameter) this firing system was inadequate. Various firing systems were considered, but after extensive trials a non-electric sequential firing system was chosen. This system fulfilled all criteria of blast design, was relatively straight forward in charging technique and had a very simple primary initiation system. Although initially designed for large mass blasts, the non-electric firing system is now used for all large hole blasting and in a simpler form for small (57mn diameter) holes.

Jan 1, 1982

Mount Isa Mines Ltd. annually extracts 5.6 million tonnes of copper ore from the 1100 Orebody. All production is by longhole open stoping, with an increasing emphasis on pillar recovery. Drilling and blasting prac- tices have been modified to allow more efficient pillar extraction, with the evolution of a "core and shell" approach. Blast design occurs at the stope design stage, while individual blast preparation is based on detailed ring plans. A programme of blasting research involving surface and under- ground vibration monitoring and fragmentation assessment has been car- ried out in conjunction with production personnel. Drilling and blasting practice in the orebody must continue to evolve with continued research, to suit changing conditions and take advantage of new technology.

Jan 1, 1988