Search Documents

By Saghafi A, Kelly M, Williams R. J

A two year program of research into the feasibility of long-hole drilling for improved gas emission control has been undertaken at Appin Colliery. State of the art equipment was employed involving cableless electronic surveying and down-hole motor drilling. The project involved the drilling of 1000 m long, in-seam boreholes in the Bulli seam and boreholes of similar length drilled cross measure and then in-seam along the underlying Balgownie seam. A new concept for gas drainage was defined, employing long-holes for both predrainage and post drainage.

Jan 1, 1988

By P Knights, M S. Kizil

Truck/shovel operations constitute 50 - 60 per cent of the cost of open pit mining operations. Mining companies, therefore, are constantly seeking to close the gap between actual truck/shovel productive capacity and maximum potential truck/shovel capacity. This paper analyses the performance of a mixed truck/shovel fleet in an open cut coal mine in Australia. It analyses operating delays, and proposes a novel graphical means of determining truck-limited or shovel-limited operations. A goal seeking algorithm is advanced in order to maximise truck/shovel match factors (MF) and hence optimise fleet productivity.

Sep 26, 2011

By McQueen LB

The Water Board has been involved in the development and ipgrading of sewerage facilities in the Blue Mountains since 1980. In 1984 the Board prepared a report that dealt with the Blue Mountains Sewage Effluent Management study. Successive 3ovemments have been concerned about development in the 3lue Mountains and the effect this development is having on the luality of the streams flowing into the Blue Mountains National ?ark (presently up for World Heritage Listing).

Jan 1, 1993

The Golden Valley Volcanic Centre has been recently interpreted as being a combination diatreme breccia pipe and rhyo-dacite flow dome complex of Permo-Carboniferous age that intrudes basement granitoids and sediments of Ordovician-Devonian age. Exceptionally good exposure at the Centre has enabled the relationships between different lithologies to be determined. This, along with petrological studies, has led to a detailed understanding of the geological environment in which the complex formed. Gold, silver and base metal mineralisation have been recently shown to be associated with the Marginal Breccia at the perimeter of the diatreme. Comparisons have been made between the geology and mineralisation in this system and several similar diatremes which also contain gold-base metal sulphide mineralisation.

Jan 1, 1990

By Lovett EP, Johnson CR, Dunlop GA

Seven streams of a low tonnage pilot plant operation on Cu/Pb/Zn ore from the Golden Grove Project were continuously assayed using an AMDEL In-Stream Analysis (ISA) system. The ISA instrumentation is briefly described as is the calibration procedure employed. The successful application of this instrumentation in the dynamic environment of a pilot plant operation is discussed. The operational sequence of the Golden Grove pilot plant is outlined along with the original project objectives and how they were achieved by the implementation of ISA. Results for the different complex flowsheets used are discussed, followed by the perceived benefits of installing such equipment in this operation.

Jan 1, 1986

A Devonian metallogenic province is extended northwards from central Queen- -sland to the Burdekin Basin in the Charters Towers Gold and Mineral Field. Devonian sediments of the Burdekin Basin are intruded by mineralised quartz felspar porphyry which occurs as pebbles in Upper Devonian conglomerate. A mineralised volcanic complex lies on the crest of an anticline in Devonian sediments.Red siltstone is slurried and reduced to pyritic hornfels over folded limestone.A thick wedge of volcanogenic conglomerate overlain by marine shale lies on the mineralised rim of an ocean which suffered cataclysmic changes during Late Devonian times.

Jan 1, 1987

By I H. Jung, W O. Choe

Gallium (Ga)-containing compounds such as Gallium Arsenide (GaAs) and Gallium Nitride (GaN) are widely used in electronic devices due to their superior electro-optical properties and their usages increase rapidly. For the sustainable supply of Ga to electronic industry, therefore, the recycling of Gallium becomes essential. Pyrometallurgical Ga recycling process involves the complex chemical reactions between slag, matte, liquid metal, gas, refractories, etc. Therefore, the accurate thermodynamic information and phase diagram data for the oxide system containing Ga2O3 is important. In the present study, new phase diagram experiments for binary SiO2-Ga2O3 and ternary CaO-SiO2-Ga2O3 system are carried out using Differential Thermal Analysis (DTA) and quenching experiments followed by Electron Probe Micro-Analyser (EPMA) and X-Ray Diffraction (XRD) phase analysis. Based on new phase diagram data and available literature data, the thermodynamic modelling of the entire CaO-SiO2-Ga2O3 system is performed for the first time.

Jun 19, 2024

By M E. Rakidjan

The DOZ underground mine at PT Freeport Indonesia is a copper and gold mine in Indonesia with current ore production of 42 000 tpd. Because of the mine expansion into the West DOZ more ventilation raises are needed to create a safe and healthy work place. All ventilation raises that connect the extraction levels to the underlying gallery exhaust drifts at DOZ are now developed using drop raise techniques. This paper describes the improvements undertaken to increase blasting efficiency, to decrease cost and reduce safety risks. This was achieved by using deck loading and presplitting, changing of stemming materials and prevention of excessive raise collar cratering (blow up).

Jan 1, 2005

Mineralisation adjacent to Herberton occurs within three main subcentres. The Her- berton Hill subcentre is characterised by the association of Sn,W the Herberton Dividing Range South subcentre by Sn, and the Herberton Dividing Range North by Cu, As. The relation- ships between the subcentres are discussed in terms of metal distribution, production, deposit types, wall rock alteration and re- lationships with granitoid intrusives. The temporal and three dimensional spatial re- lationships between the centres are uncertain.

Jan 1, 1978

The Martha Mine is an open cut operation situated in the midst of Waihi town which has been operating since 1987. Since then it has produced some 700,000 ounces (oz) of gold and 4,000,000 oz of silver from an epithermal vein system. It was previously worked by underground methods from 1880 to 1952 to a depth of 600 m producing 5 million ounces (Moz) of gold and 30 Moz of silver. The licensed reserves are scheduled to be mined out early in the year 2001. An additional economic resource of over 750,000 oz of gold has been identified which can be accessed by deepening the pit a further 50 m along the main Martha vein. This would extend the mine life to the year 2007. Applications were lodged on 4 July 1997 for the necessary resource consents, discharge permits and variations for the current Mining Licence conditions. The extension project requires approval from the District Council, Regional Council and the Ministry of Commerce. The consent and permitting process is extensive because of the urban setting of the mine. An approach to keep the extension as similar as possible to the current operations was adopted to give the community and authority confidence in the proposed extension. This paper summarises the extension detail and the permitting requirements it has had to address despite the extension being "more of the same". The permitting process has been exhaustive with little recognition of the standards already achieved in protecting the environment which are recognised worldwide.

Jan 1, 1997

By Itoh K, Sakai K, Tsuji K

In Japan there exists a strong demand for mechanical excavation for tunnelling bacause the blasting method which produces much vibra- tions and noises is restricted in its applica- tion due to the fact that there can be many cases where tunnelling sites are located ad- jacent to residencial areas as a result of Japan's being a thickly inhabited country. Pressing demands for and deep interest in the mechanical excavation method have been shown by the circles concerned with reasons that it produces smooth cutting surface and causes less overcutting of profile as a result of the diffusion of NATM (New Austrian Tunnel- ling Method) in the recent years. This has caused a strong desire of the users to apply the conventional mechanical excavation method that has been used mainly for soft rock cutting also to the field of hard rock cutting. In order to meet such needs of the tunnel- ling industry, further research and development have been continued to have successfully real- ized the Boomtype Tunnelling Machine for Hard Rock.

Jan 1, 1987

By R Berry

This paper looks at two ways to estimate the bulk mineralogy of the rocks for assay intervals. The aim is to find an efficient indicator of the most common minerals in the rock. Phase (modal) analysis has traditionally been done using visual methods such as point counting and image analysis. A modern version of this process is the X-ray point counting routine using the SEM-EDS based software. These methods are too slow and expensive for routine analysis of bulk sample mineralogy at the normal assay spacing.Two sources of data were considered that provide information that can be used to determine the mineral abundance in assay samples. The most widely applied method is (semi-) quantitative X-ray diffraction (QXRD). The QXRD method is most applicable to major minerals and has limited application to minerals at low abundance. The nominal detection limit is 0.5 per cent. Values below five per cent have large errors. A second, less common, method is calculation of mineralogy from chemical assay data. Conversion of chemical analyses to mineralogical analyses depends on the unique chemical composition of each mineral. Elements only found in one mineral are easily accounted for, but many compositions are ambiguous. Deciding on the actual mineralogy is not simple. Recalculation of mineral mode from chemical analyses is more accurate than QXRD when the correct minerals, and mineral compositions, are known.Where only a few QXRD analyses are available they can be used to setup a protocol for calculation of mineralogy from assay data. Linear programming works well in this environment. The best results are obtained when both H2O and CO2 are directly measured. Loss-on-ignition (LOI) should be included if these are not available.Where both QXRD and chemical analysis are available for all samples, the best results are obtained using the least squared method to merge the data sets assuming QXRD has much higher analytical errors than chemical assays. The combined method provides more robust results because the high abundance minerals are controlled by the QXRD measurements while the chemical assays improve the precision for low abundance minerals

Sep 5, 2011

By Corrans I. J, Yan D. S

The CIP process for gold recovery has enjoyed widespread application in most gold-producing countries. The development of a mathematical model of the CIP process has value for use in process design, process optimisation, and process control. Mathematical model development through laboratory experimentation is an important step in the design and optimisation of the CIP process. For this purpose, data has been generated through small scale laboratory leaching and adsorption tests both in batch and continuous mode. This test program has been carried out on specific ores of various types prior to the application of the models to production CIP plants utilising these ores. The applicability of leaching models derived from batch experiments was tested in a continuous five stage CIP pilot plant. The models were then adapted to scale-up the batch to the small scale continuous operation.

Jan 1, 1991

Unprecedented political, economic, and social change throughout the world will have an increasingly profound effect on the dynamics of the world's mining industry. Analysis of the early financial trends in this development (statistics on exploration expenditure, and investment flows) gives some insight into the magnitude of structural change and its implications for established mining economics and companies.Increasing confidence in the stability of many third world and developing countries is attracting exploration and investment capital that had previously been largely directed to established mining economies in North America, Australia, Europe and Southern Africa. Some of the projects requiring capital and technology in the CIS, Africa and Latin America are technically very attractive. The end of the 'cold war' and the influence of the IMF is gradually changing their risk profile for mining investment.

Jan 1, 1993

Conflicting claims and views on the priming of ammonium nitrate/fuel oil (ANFO) are reviewed; certain fallacies and misconceptions are rectified. Optimum priming systems for a range of blasthole conditions are indicated. Moves towards optimum priming lead to reductions in the combined cost of drilling, blasting and handling the material. With shallow blastholes, two-point priming is rarely warranted. Best blasting results from single priming are usually obtained when the primer is located near, but not at, the bottom of the blasthole. As blast- hole depth increases, two-point priming becomes more reliable and effective than single priming. For two-point priming, primers should be located such that detonation waves in the ANFO collide at grade level or, if preferred, within a hard band in the burden. Where blastholes are very deep and/or strata variations can be appreciable, three or more spaced primers are often justified. The effectiveness of a primer varies with its detonation pressure, diameter and length. Primer properties influence the velocity of detonation (VOD) near the primer, but do not affect the final (steady-state) VOD in the ANFO. Some primers cause 'run-up' (i.e. lower than steady-state) velocities whereas others cause

Jan 1, 1974

By T Kon, K Ohno

Slag foaming is an important control item in the process of refining molten steel. This study aims to investigate the factors controlling slag foaming by observing the bubble formation behaviour resulting from the chemical reaction between iron oxide and Fe-C alloy in the slag. In this study, 0.06 g of Fe- C alloy was introduced at the bottom of a BN crucible, and 6.0 g of slag (SiO2:CaO:Fe2O3 = 40:40:30) was placed on top of it. The crucible was positioned inside an infrared image heating furnace, where the temperature was rapidly raised to 1370°C at a rate of 1000°C/min in a nitrogen stream, and then held at that temperature for a predetermined time before rapid cooling. Following rapid cooling, the internal structure of the sample was examined using a high-resolution X-ray CT device. The spherical equivalent volume was calculated based on the number of observed bubbles and their equivalent circle diameter. Additionally, the relationship between the volume ratio of small bubbles in the slag volume and the distance from the bottom of the crucible was determined, along with the calculation of bubble density and volume ratio. Under various experimental conditions, numerous bubbles with equivalent circular diameters ranging from 200 to 300 μm were consistently observed. The density and volume fraction of bubbles with circular equivalent diameters between 200 and 500 μm showed a tendency to increase as the distance from the bottom of the crucible increased. Bubbles with equivalent circular diameters of 500 μm or more consistently exhibited lower bubble densities, regardless of their height within the crucible. The formation of larger bubbles is attributed to a decrease in iron oxide concentration within the slag as the reaction progresses. However, this is believed to be due to their higher buoyancy, resulting in shorter residence times within the slag and a reduction in the number of encapsulated bubbles.

Aug 21, 2024

By Kupper T

Firstly, electric analog models are discus- sed to show fluid streaming conditions. In these models the depth of blast at tuyere level, the height of the bath, the influ- ence of different angles of the furnace zones and the different possibilities of the root of the cohesive zone have been changed. Tests to define the influence at a large blast furnace are given. Secondly, the wear of carbon bricks in the hearth is examined under the influence of gas, slag and pig iron. Oxidation tests in a special scanning microscope with the pos- sibility of heating and gas treatment are shown. Wear mechanisms are discussed fora large blast furnace and proposals for im- provement are given. Finally, the possib- ilities and value of the temperature meas- urement in the hearth block are discussed.

Jan 1, 1981

By Sheard SN, Tucker DH

Sampling procedures are an important aspect of geophysical exploration survey design. It is good practice that the selection of survey parameters ensures that the signal to noise ratio is optimised, while minimising survey cost.Sampling considerations for any geophysical method include the size of the target, scale of observation, aliasing associated with station and line spacing, nature and extent of overburden, and the presentation of data.As a guide to survey design, the specifics are discussed for three geophysical techniques in common use in mineral exploration; these include the magnetic method, transient electromagnetics and induced polarisation.

Jan 1, 1976

Underground mechanized excavation in New Zealand has become more commonplace in civil and mining applications during the last three years. At one stage up to seven Dosco Road- header machines were being used on different projects around the country. The Huntly West Mine Drifts inclined at one in four were by far the most severe grade conditions that the machines were subjected to; however, other operations posed their own particular problems for the machines. Two major interrelated factors became evident as soon as the machines commenced at Huntly. These were traction problems on the grade and control of water, particularly on the invert.

Jan 1, 1978

By P Kumar, J Safarian

Understanding how ore interacts with flux particles at elevated temperatures to create molten slag is crucial since it governs the dynamics of a chemical reaction. This study explores the smelting behaviour of pre-reduced Nchwaning manganese ore when combined with lime, with the objective of examining the evolving interaction between pre-reduced ore particles and lime over time. The research sheds light on the interaction between solid and liquid and the phases that emerge during this process. To achieve this, a sessile drop furnace was employed to rapidly heat the materials positioned adjacent to each other on an alumina substrate and to observe the smelting process as it unfolded over time. This method allowed for the direct observation of the melting temperatures and the flux-ore reaction progression rate, and the potential disruptive events that might occur. By comparing the molten interfaces of the fluxed materials at various time intervals, this study provides insights into the relative rate of slag formation from the two materials. The results indicate that the main slag formation initiated at approximately 1400°C and continued to advance with time, with complete mixing occurring around 1500°C. The possible phases formed were identified using Scanning Electron Microscopy and modelled using Fact Sage thermodynamic software. In addition, the iron particles in the pre-reduced Mn ore were separated and settled from a rich MnO-containing slag. It was found that the separation of molten iron droplets from the slag depends on the rate of solid MnO particles dissolution into the adjacent slag phase.

Jun 19, 2024