Search Documents

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

By S Saydam

Professional engineers need to be able to apply university learning to practice. In particular, they have to take responsibility for interactions between technical systems and the complex social environments in which they operate. The most effective way of building this competency is through active experiential learning. We have been developing an advanced educational integrated simulation system to provide mining engineering students with an interactive and immersive learning experience that is not otherwise possible. This will give students an authentic experience in working with industry software packages, while also contextualising the learning in terms of the broader and longer-term impact of technical decisions. We have been piloting the system, in undergraduate courses in order to establish its effectiveness in building systems thinking competencies for mining engineering. For postgraduate students and professionals, the same tools and methods can support studies of more challenging and complex scenarios where mining engineers have to place their decisions within complex global industry contexts.

Nov 22, 2011

A major problem in the continuous casting of aluminium killed strip steel is the incidence of black and grey lines in the strip surface caused by the alumina inclusions. One place for limiting the number of alumina inclusions is by providing favourable fluid flow conditions in the ladle so that the inclusions float out to the surface or adhere to the ladle wall. In laboratory equipment 20 kg of steel was melted in an alumina crucible of 14 cm diameter in an induction furnace. Deoxidation was carried out while the melt was constantly stirred by argon bubbling. Bubble frequencies were measured at the lance tip using a microphone technique. High speed cine photo- graphy was incorporated to measure melt top surface velocities. Experimental results indicate that the rate of removal of inclusions is a function of both the gas input and the power input. However due to unfavourable surface area to volume ratio, reoxidation of the melt took place. Some other experimental difficulties in working at high temperatures are also discussed such as lance design, melting arrangement and sampling techniques.

Jan 1, 1984

Recent developments in engine, transmission and control technology, likely to give rise to improved performance and efficiency of underground mobile equipment, are reviewed. Turbocharging and the electronic control of fuel pumps and injectors can improve diesel engine performance whilst minimizing exhaust emissions. Ceramic materials promise further improvements in engine efficiency. Nevertheless, electrically powered machines, equipped with trailing cables or 'travelling plugs' are expected to find increasing application where there is less need for flexibility and where the cost of ventilation and heating or cooling makes diesel engines unattractive. Voltage to frequency converters and induction motors appear to have a future in mains powered machines. Vehicles employing energy storage in the form of batteries or flywheels will find increasing application, but it is expected that they will remain a minority until there is a significant break-through in battery technology. Hydrostatic transmissions having high power density and efficiency are likely to be used more widely. Electronic control systems are likely to be used to simplify jobs and to improve performance and productivity. Enhancement of remote control systems is to be expected for work in unsafe areas, but true robot operation is considered unlikely for the moment. Attention to ergonomic factors should produce significant productivity gains.

Jan 1, 1985

The Myally Beds, Surprise Creek Beds and Mount Isa Group form the upper part of the Proterozoic Western succession of rocks in northwest Queensland. The latter two units are partly equivalent, and are important for their base metal content at Mount Isa and elsewhere. The arenaceous Myally Beds lie unconform- ably or disconformably below the Mount Isa Group and Surprise Creek Beds; they contain four mappable units which were deposited on a broad, shallow shelf washed by east-trending currents. Emergence of the Myally shelf initiated a series of parallel, possibly intra- cratonic, troughs to the east and west. In the east, the Surprise Creek Beds were deposited between the emergent shelf and base- ment rocks, and consist of a shelf and trough facies divisible into 7 and 10 units, respectively. Trough sediments are continuous north-south, and show turbidite character- istics; algal dolomite characterizes the shelf facies. To the west in the Mount Isa trough, an orthoquartzite facies, the Warrina Park Quartzite, defines the base of the Mount Isa Group. Hinge zones between the shelf and trough environments are marked by east-west facies changes, and provide a focus for later major north-south faulting. However, some penecon- temporaneous faulting near Mount Isa is best explained as complex post-depositional faulting of a disconformable sequence. Subsidence and deposition in the Mount Isa trough continued for a longer period than in the Surprise Creek trough, allowing accumulation of lead and zinc deposits in the upper half of the sequence. The Surprise Creek Beds appear equivalent to the lower half of the Mount Isa Group, and are probably not prospective for lead and zinc. Turquoise and possible other secondary copper minerals are widespread in the Warrina Park Quartzite and equivalents in the Surprise Creek Beds, and further investigation of these formations seems warranted.

Jan 1, 1974

By Y Yang

Despite the importance and usefulness of basicity in metallurgical slags, the optimum quantitative expression of it has remained elusive, partly due to the fact that the precise concept of basicity has not been properly clarified. The two basic approaches to the concept of basicity are the Lux-Flood, which perceives basicity in terms of the activity of the free oxide ion, aO2-, and the Lewis, which perceives basicity in terms of the ability to donate negative charge. The former has been almost universally adopted in the area of metallurgical slags, while the latter has been increasingly accepted in the field of glass chemistry. In this paper, some difficulties of the Lux-Flood approach are pointed out, including the need for indirect measures of aO2-, which have proliferated in recent years. Accordingly, it is suggested that the Lewis approach has a good deal to commend it, and that the quantification of it in terms of optical basicity is the best measure of basicity available, which should therefore be more widely applied in metallurgical slags than it currently is. The fact that there are intrinsic problems in evaluating the optical basicities for the transition metal oxides is acknowledged, and a new scale is recommended. The patterns of iso-optical basicity lines in ternary systems are shown to agree well with the pattern of iso-activity and iso-capacity lines under appropriate conditions.

Jan 1, 2000

By McKew M, OÆRegan

Rapid access longwall mining' or 'longwail punch mining' is a proposed extraction method whereby longwall gate roads are driven into a seam directly from an opencut highwall. The longwall panel thus formed is retreated back to within 40 m of the highwall providing an extremely simple, reliable and therefore highly productive longwall mining system. The concept is of particular benefit for the recovery of isolated pockets of coal (adjacent to a highwall) not easily accessible from a conventional underground mine. As panel gate roads are driven directly from the open strip, minimal delays are incurred between the end of open cut and start of underground production, allowing the method to bridge the gap between open cut mining and a total underground commitment. The study was specific to the Bowen Basin, and given the likely conditions, no significant operational or geotechnical hinderances to the concept could be identified. It was therefore concluded that longwall punch mining would not expose the operator to any additional risks above that normally associated with the introduction of longwall mining. Thus, longwall punch mining is an attractive option, both operationally and financially, for open cut mines reaching their maximum economic Death.

Jan 1, 1988

Proposals designed to use stockpiles and buffer stocks to achieve price stabilization and better resource use have a long history. They are super- ficially simple to understand. The benefits seem clear. And yet I am well aware that this is not a simple subject: the more one studies it, the more complex it becomes. Worldwide interest in re- source management, while receiving fresh impetus from the OPEC actions, also has a long and chequered history. Those venturing into such ter- ritories must be forewarned of the traps and pit- falls which abound. Interest in these schemes has waxed and waned over the years with the fluctuating fortunes of the producers or consumers. As I write this paper towards the end of 1977, I am acutely aware of the low ruling prices for zinc, copper, and nickel. These sacrifice prices remind me that it is difficult, for example, for a surveyor, to be calm and rational if he is up to his neck in a swamp full of crocodiles. He might be forgiven for forgetting that the aim was to drain the swamp! I am also aware that when swamps are drained, painful and dangerous stumps sometimes stick out. Hence, in looking at the subject of stockpiles and resource management we must not set our sights too high, perhaps not initially hope for perfec- tion, if we want to secure worthwhile changes. My approach is to acknowledge a bias for the market system. We have, however, had experience (remember the 1930s) of some weaknesses in the untrammelled operation of free markets. Thus our international economic relationships over the past 20 or 30 years have been based on a desire to retain as much as possible of a liberal world trading system backed by such organizations as the GATT, IMF, and the U.N. to ensure the necessary cooperation. Some nations have seen this system work only partially in their best in- terests. GATT, for example, has been reasonably effective in liberalizing trade in many manufac- tured goods but far less so in regard to agricultural or semi-processed goods.

Jan 1, 1978

By W D. Ortlepp

Seismicity associated with deep block cave mining operations in hard rock can give rise to dynamic loading of the mining openings. A description is given of the source and damage mechanisms associated with such seismic events, and the possible demands placed on the rock support by the resulting dynamic loading. In addition, production level drifts are often subjected to large static deformations during mining. Appropriate support, able to sustain large static deformations, and capable of absorbing the energy released during dynamic loading, is described. The performance of these support types has been determined by means of large-scale dynamic loading tests, and large deformation static laboratory tests. Finally, a support system which is considered to be appropriate for extraction drifts in block cave layouts subjected to dynamic loading is described.

Jan 1, 2000

By L Smith, R Beckie

An intermediate scale (8 m + 8 m + 5 m high) constructed waste rock pile experiment was built upon a contiguous grid of 16 gravity drainage lysimeters to investigate the flow of water in unsaturated waste rock. Average net infiltration to the uncovered waste rock pile is 55 per cent of precipitation. Large rainfall events have net infiltration of 55 per cent to 85 per cent. Net infiltration estimates range from 23 to 120 per cent of precipitation between lysimeters. Small-scale lysimeters of less than 4 m2 area are shown to be poor predictors of net infiltration for uncovered waste rock. The appropriate size for lysimeters increases with increasing flow rate. The residence time distribution has an estimated median value of 3.0 to 3.9 years under average infiltration conditions. Water flows within the fine grained matrix, within larger pores (macropores), and in matrix free areas of the pile. In situ tracer concentrations vary between pore sizes, and between spatially distinct areas of the pile, indicating water geochemistry may also be variable. Water samples collected from in situ soil water samplers are dominated by the most mobile water fractions. In situ measurements of water content and matric suction are compared to the measured outflow. The data indicate the focusing of flow in spatially distinct areas can make in situ instrumentation a poor (non-conservative) predictor of volumetric water flow.

Jan 1, 2003

By Y B. Kang, Y J. Park

Ti-added ultra-low carbon (ULC) steel is produced by adding Al and Ti during the secondary refining process to deoxidise molten steel and to bind C and N which are detrimental to the deep drawing quality of the steel product. However, the production of Ti-added ULC steel faces challenges, including submerged entry nozzle clogging and surface defects on cold rolled coils. The troubles were often attributed to ‘Al-Ti complex inclusions’ in the molten steel. However, the evolution of oxide inclusions including their stability has been still unclear. In the present study, the evolution of these inclusions in Ti-added ULC steel was investigated by phase diagram measurement, CALPHAD thermodynamic modelling, high-temperature stability test for the oxides, and observation of transient behaviour of oxide inclusions in the steel. The phase diagram of the Al-Ti-O system was elucidated with an emphasis on oxygen potential, which significantly controls the stability of the oxides. CALPHAD thermodynamic models and a self-consistent database were developed. The transient behaviour of Al-Ti complex inclusions in Ti-added ULC steel was observed in situ using a confocal scanning laser microscope. This was additionally validated by the new thermodynamic model. The equilibrium phases of the oxide inclusions were investigated using a high-temperature resistance furnace, and were analysed using a secondary electron microscope, energy dispersive spectrometer, and electron back-scattered diffraction. By considering the morphology and crystal structure of these inclusions, the evolution of Al-Ti oxide inclusions was elucidated. Various behaviour of Al-Ti inclusions and their influence on steel cleanliness are discussed.

Aug 21, 2024

On the 18th November, 19'58, the first coal was delivered to the Morwell Power Station from the adjacent Open Cut using conveyors for the transport of the coal from the working face to the boiler bunkers. As the cut develops the coal seam will be worked for its full depth of about 360 feet from four benches, each feeding a conveyor line along th.e face and up out of the cut to the power station and briquette factory. By 1970 the estimated maximum daily demand reaches 60,000 tons and the total annual output 18 million tons. The complete conveyor installation will then total some 9 miles with a capital cost of over £3~ million.The choice of conveyors in place of the more usual rail system was made possible by the development of movable belt conveyors which use mechanical conveyor shifting, high belt speeds and flexible high strength belts and the paper deals with these and some other aspects of the scheme.INTRODUCTIONThe development of brown coal deposits is usually based on open cut workings equipped with a few large dredgers giving an almost continuous output of coal or overburden which has to be hauled a comparatively short distance. These are ideal conditions for conveyor operation, and it is surprising that, until recently, rail transport has been used almost exclusively in brown coal open cuts. In some cases inclined conveyors have been introduced to take the coal from the coal levels up out of the cut to bunkers at groundlevel, but trains have been left to operate between the ditch bunker feeding the conveyor system and the dredger.

Jan 1, 1960

By T Davis

Cameco Corporation operates the high-grade 140 tpd fly-in/fly-out underground McArthur River Uranium Mine in Northern Saskatchewan in a joint venture with Cogema Resources Inc. Reserve grade is in excess of 20 per cent U3O8 with current mining grade averaging 16 per cent U3O8. Due to the high radiation potential of the ore, the non-entry mining method of raiseboring was chosen to minimise worker radiation exposure potential. The raisebore and extraction horizons are located in waste rock with the orebody located between horizons. Ore produced by raiseboring is delivered by LHD to an underground SAG mill and is then hydraulically hoisted to surface receiving facilities after underground thickening to 50 per cent solids by weight. Concrete backfilling is utilised. The orebodies at McArthur River are adjacent to water bearing sandstone. Ground freezing is therefore employed to isolate the ore from this water bearing ground. Calcium chloride brine at -35¦C is circulated through a series of cased boreholes to establish freeze walls up to 25 metres in thickness. At 18 000 000 lb of low cost U3O8 production per annum, McArthur River ranks as the worldsÆ largest uranium mine. Over 50 per cent of the workforce resides in this sparsely populated area of Canada with approximately 40 per cent being of aboriginal ancestry. Site operations must cater for winter temperatures as low as -50¦C.

Jan 1, 2002

The Australian mining industry is at an interesting stage in its development. Of the large number of mining companies in Australia, some are still solely domestic in their focus. others have made their first tentative forays offshore, and others are global players of significance in the world industry. It is not long ago that the entire industry was almost exclusively domestic in its focus. Very few companies before the early 1980s had ventured offshore, and those that did so were considered quite risque. The initial moves were made mainly by large companies who could afford to lose the funds expended in getting started in a range of offshore locations.

Jan 1, 1995

By Woodcock JT

Successful chemical control of flotation requires practical solutions to many problems. A brief discussion is first given of those para- meters which can be controlled and those which it would be desirable to control. Suitable analytical methods for application to flowing pulp and to clear solution from pulp are out- lined in relation to on-line and off-line control. Practical problems of deciding where a measurement is to be made or a sample is to be taken and how the sample is to be prepared and presented to the measuring device are then considered. Equipment calibration and maintenance are considered in relation to the above factors.

Jan 1, 1978

By Rongqing Q, Tiancong Z, Yiyuan L

The influence of pulp density, ferric ion concentration and particle size on the tank bioleaching of two kinds of refractory gold concentrates are discussed. The chemistry and mechanism of the bioleaching process are also presented. The relationship between oxidation of sulphides, liberation of enclosed gold and gold cyanidation are discussed. The consumption of NaCN could be reduced by alkaline treatment of bioleached residues prior to Cyanidation.

Jan 1, 1992

The most frequently applied project evaluation criteria are the Net Present Value, the Internal Rate of Return, and the Pay Back Period. Unfortunately, the Internal Rate of Return and the Pay Back Period, if interpreted according to their traditional definitions, easily produce results which contradict the Net Present Value. The reasons for the Net Present Value incompatibility of the two criteria are that these criteria have not been adequately defined and so new, complete definitions are recommended. The concept of the True Rate of Return is proposed as a substitute for the interest rate that the Internal Rate of Return has been believed to represent. The redefined Internal Rate of Return and Pay Back Period criteria, as well as the True Rate of Return are all Net Present Value compatible and can, therefore, serve as independent project evaluation criteria. Also, the correct approach to the evaluation of mutually exclusive alternatives and the status of the often neglected borrowing projects in project evaluation are found to be quite important.

Jan 1, 1991

By Seedsman RW, Duncan Fama ME

Mine design procedures will be revolu- tionised by technological developments in computers, software, database construction and management, and numerical modelling programs. Developments in geotechnical databases will be required which utilize geological and geomechanical tests to supply appropriate input for numerical models. Techniques utilizing sedimentological and structural modelling are described. The capacity of current numerical models in mine design is outlined and a program for developing a fully integrated mine design package proposed.

Jan 1, 1987

By Smith M, Milton T, Pitt G

High levels of contamination (non magnetics) were present in the magnetite medium of the D.M. cyclone circuit. Attempts were made to minimise the amount of undersize (-lmm) material in the D.M. cyclone feed by improving initial desliming and examining those factors that contributed to any overall reduction in desliming efficiency. Circuit density control was improved and a system of continuous contamination monitoring implemented. A brief description is included of the major alterations to circuit control philosophy. The significant improvement in overall D.M. cyclone circuit performance is outlined.

Jan 1, 1987

A resume covering currently accepted views on blasting vibration measurement, human response, and criteria for damage is presented as background information for readers who are not conversant with blasting vibrations. This is followed by sections on vibration level estimation and blasting techniques to control vibration. Emphasis is placed on making use of the scatter in the delay intervals of half-second delay detonators, the use of smaller explosive charges for early delay numbers, and the non- use of zero-delay (instantaneous) detonators in cer`a. n cases.

Jan 1, 1976