Search Documents

In looking towards 2000, it is more than appropriate that we look back on the history of diamond drilling to give us a better understanding of where we have come from and see the significant advances that have been made.

Jan 1, 1992

Cerro Matoso (CMSA) in Colombia produces ferro-nickel from lateritic ore containing approximately three per cent nickel, using a Rotary Kiln - Electric Furnace (RKEF) process, in which the calcining of the mineral within the kiln is second in importance only to the smelting of the mineral in the Electrical Furnace. This article discusses the installation and operation of an expert system to control the kiln of CMSA. In the CMSA process, the run-of-mine ore is crushed, homogenised, dried and mixed with a small percentage of coal, before being heated up to 900¦C in a rotary kiln in the presence of natural gas mixed with air in a controlled proportion (air/gas constant ratio). The final objectives of the process are the following: ò To reduce to a minimum the iron and nickel oxides in order to convert these into metallic ions; this is a reduction process to facilitate largely the smelting in the electric furnace. Since the reduction is made with natural gas, it is much more economical than the subsequent complete reduction in the electric furnace, since electrical energy is much more expensive by unit of processed mineral. ò To heat the mineral as much as possible to facilitate the subsequent smelting. ò To eliminate totally the moisture content of the ore. An expert system with fuzzy logic was commissioned in 1994 for the control of the kiln and it has operated with good results ever since.

Jan 1, 1996

By Abraham B. K, Jensen B, Gillies A. D S

The aim of the research was to investigate the feasibility of using an impedance cell and ratio-transformer bridge to measure solids content in coal slurry pipelines. It appeared that this technique could be developed to measure variations in conductance which correlate with solids content. Successful implementation of the measurement technique would have a variety of applications in existing coal wash plants and the potential for automatic process control. A small pilot plant was designed for a feasibility study. This was a closed loop system in which the coal was uniformly dispersed in a tank with a variable speed agitator and then circulated through an external pipe returning to the top of the tank. The impedance cell was located near the end of the external pipe. Slurry concentrations were varied from clean tap water to 50 per cent solids by weight with the addition of weighed quantities of dry coal dust. Ratio-transformer bridge measurements showed that variations in individual observations were equivalent to measurement errors of about two per cent. These probably reflect variations in concentration of the mixture in the pipe. Data for increments in concentration of one per cent indicate that this is about the limit of resolution of the current system. The paper discusses the principles of operation of the impedance cell and measurement system. Results from the pilot study and proposed improvements in the impedance cell design are examined.

Jan 1, 1995

By Goldstone A

The paper introduces a newly developed multi-function test rig for fracture grouting. This test rig has many functions and its performance is consistent. It can control and adjust accurately the opening degree of fissures and static pres- sure; it can measure automatically the quantity of grout injected; it can measure precisely pressure drop of grout in fissures; it can test the results of injection, including effective dispersed distance, anti-filtration capacity of consolidated body, mechanical strength, etc. It can inject a single or two grouts into one or several fissures at a pressure of 16 MPa. Therefore, it is an ideal test rig for fracture injection. The paper depicts all the components of the test rig, its performance and application of the results obtained from fracture grouting tests. Examples are briefly described.

Jan 1, 1988

In the last few years a number of mineral laboratories were established in Indonesia coinciding with the increase in gold exploration in the region. Prior to this, much of the analytical work was sent outside the country,however this is no longer neccessary.

Jan 1, 1990

By Lownds C. M

Several classes of commercial explosives and blasting agents behave non-ideally, especially in diameters near their critical diameter. A direct and convenient measure of non-ideal behavior is the detonation velocity (VOD); if the VOD is less than the ideal value, usually obtained by calculation, then the explosive is detonating in the non-ideal mode. Such lowering of the VOD is usually due to both lateral loss of energy and post-CJ release of energy. The second of these factors, namely slow release of chemical energy, is of most interest in blasting. While the observation of a low VOD clearly suggests slow reaction of part of the explosive composition, it does not necessarily mean that the energy is lost to the overall rock-breaking process. The partition of the energy of the explosive into various useful and wasteful categories is considered. Simple models of energy partition in blasting, and of explosive reaction kinetics, are presented. The models consider the effect of explosive type and rock type, the explosive being described in terms of the most common phases namely liquid, air bubbles, porous ammonium nitrate, dense or crystalline ammonium nitrate, and aluminum. Over a range of combinations of the above phases, the model predicts reasonable critical diameters and VOD's. Results are presented which show the effects of non-ideal detonation on fragmentation and heave in different rock types. Conclusions are drawn about those blasting conditions in which ideal behavior is beneficial, or Disadvantageous.

Jan 1, 1990

AND INTRODUCTION The Lochiel coal deposit, a large Tertiary soft brown coal deposit in the mid north of South Australia, is currently being investigated by the Electricity Trust of South Australia (ETSA) as a potential source of fuel for a base load power station. Feasibility studies indicated that the proposed dragline method of overburden removal was viable but economically sensitive to both highwail and dump batter angles. The unusual properties of the unconsolidated overburden sediments and the groundwater regime posed a number of intimately related hydrogeological and geotechnical questions which were addressed before and during the excavation of a trial pit. All strata at Lochiel are of soil strength, and artesian aquifers occur above and below the coal. From the initial evaluation of the deposit a number of hydrogeological questions were defined. These related to the rate at which the pore pressure in the silts is reduced by dewatering, the extent of the reduction in pore pressure due to prestripping, and the feasibility of dewatering and depressurising carbonaceous silty sand sequences. The site of the trial pit was selected to answer these and other questions from the basis of a detailed geological, hydrogeological and geotechnical understanding. The trial pit dewatering system simulated a full scale mine dewatering system and included ten pumped wells, twenty drainage wells, and nearly 400 monitoring instruments. It operated from September 1986 to June 1987. The excavation was carried out between February and May 1987.

Jan 1, 1988

By Morandini AF, Occella E, Clerici C, Mancini R

This contribution presents the first results of an experimental research aimed at finding an unified description of the first stages of a rock comminution process. With reference to the case of the jaw crushers and to the specific subject of the comminution law, the tests reviewed and analysed in this contribution have been carried out, at a laboratory scale, on five different materials (limestones, quartzite, serpentinite) at different reduction ratios and feed rates, and accurately recording both total power and idle running power. The analysis of the results has shown that: ò the grain size distribution of the products complies with a modified form of the Rosin-Rammler equation, already found to be well suited to representing the grain size distribution of blasted rock in previous works by the authors; ò observed trends of the consumed power at increasing reduction ratios is steeper than predicted by the classical Rittinger, Kick and Bond laws, Rittinger law representing however a closer approximation of the experimental results; and ò a more accurate description of the experimental results is provided by a modified form of the Rittinger law. Accuracy of the semi-empirical expression has been found to be usually better than ten per cent by comparing actual results with expected Results.

Jan 1, 1993

By Denisov GA

Conventional processes for disintegration of ores are characterised by low selectivity and cause damage to the components of their structure. It affects their liberation and recovery which are connected also with the inevitable formation of extreme fines. In the world practice recently came into view 4 trend to grinding of materials within a thick layer (in a bed layer), which provides a substantial selectivity of liberation, for example, of kimberlite. The degree of diamond preservation in the final product is highly increased. However, this method causes a considerable overgrinding of material. A new method of intralayer vibro-impulse breaking of materials providing an easily adjusted force acting at the layer and timely removal of product size grains from the grinding chamber has been developed in Russia.

Jan 1, 1993

By Floyd JM

Pilot plant trials showed the effective ness of the submerged lance SIROSMELT technology for altering the composition of iron blast furnace slags as a preliminary step to produc- tion of formed materials. Mixtures of oil and air were injected into a bath of liquid slag to provide the heat required for melting the additives and to provide very turbulent conditions which resulted in complete dissol- ution of added fluorspar within one minute and almost complete dissolution of silica in two minutes. Sulphur lost during injection was readily made up by addition of pyrite or pyrrhotite. A stable foam could be readily made and broken down and the foamed slag appeared suitable for extrusion or forming into shapes.

Jan 1, 1979

By Hall S, Upton D

WMC Resources Ltd nickel operations have expanded significantly over the last three years. Production capacity has increased at mine/concentrate, smelting and refinery processes to such an extent that WMC now ranks within the top three or four producers of nickel metal in all forms. The stainless steel industry remains the dominant user of nickel. WMC's forecast is for stainless steel production to grow at 2.8 per cent per annum off of the 1995 peak, with much slower growth in the short-term as the stainless steel inventory overhang unwinds, followed by a return to higher trend growth rates. WMC's forecast for the long-term growth in demand for primary nickel is three per cent per annum off the 1995 peak; again, slower growth in the short-term before a return to higher long-term trend rates. This projection is towards the optimistic end of the range of industry experts. It equates to a requirement for new primary nickel of 25 000 to 30 000 tonnes of annual capacity each year.

Jan 1, 1996

By Fullagar P. K

In resource definition and mine development, major capital expenditures are committed on the basis of sparse information and even in production surprises such as bad ground are not uncommon. Drill holes constitute the principal source of information about the orebody and its environment and optimisation of drilling implies maximising the yield of useful information per dollar expended. Geophysical borehole logging provides new flexibility for optimising the drilling budget. Economic benefits can flow from geophysical logging at all stages of the mining cycle. The most commonly cited benefit is substitution of diamond delineation drilling with cheaper percussion or reverse circulation drilling in cases where geophysical logs can substitute for core. This approach can deliver an attractive direct saving in drilling costs (and time) if drill meterage is unchanged, or a potentially greater indirect benefit from better ore control if more holes are drilled within the original drilling budget. More ore contact intercepts per dollar can translate into lower dilution and enhanced ore recovery, thereby increasing revenue as well as reducing mining costs. Substitution of diamond drilling with percussion drilling is not always feasible. However, geophysical logging of diamond holes is often highly advantageous in its own right, both for geotechnical characterisation as well as ore delineation. Operational advantages of logging include data objectivity, speed of interpretation and reduced core handling and analysis costs. Geophysical logging assists mining engineers by providing a continuous measure of in situ rock strength, even over intervals with poor core recovery. The additional expense of geophysical logging in blast holes can be justified in terms of more accurate ore boundary delineation and rock strength evaluation. Precise ore boundary delineation permits refinement of charge placement, to minimise dilution and maximise recovery. Detailed knowledge of rock strength can enable optimisation of blast design. Rock strength can be evaluated in real-time via analysis of drill performance data recorded with measurement-while-drilling (MWD) technology. To successfully apply geophysical logging in mines, its technical, operational and economic viability must all be established. This entails verification of the existence of appropriate physical property contrasts, investigation of the best way to integrate the geophysical results with the mining method and an objective assessment of the value of the resulting mine performance benefit. Geophysical logging is already well established in many mining operations. The greatest impediments to its wider utilisation at mines are: lack of appreciation of geophysics by most mine geologists, engineers and managers; limited interpretational aids; and the necessity to re-enter completed drill holes. In this paper we endeavour to address these issues by informing mine geologists about potential applications of geophysics, by illustrating automated interpretation of geophysical logs and by highlighting the importance of emerging MWD and logging- while-drilling (LWD) technology.

Jan 1, 1997

The problem of manufacturing from sulphuric 'acid and Christmas Igland "A" phosphate, superphosphate of acceptable physical condition and agronomic phosphate availability, is directly related- to the crystallisation of a reac- tion product, monocalcium phosphate monohydrate. Two solutions to the problem, vacuum drying the superphosphate and calcination of the ore before reaction with acid, are discussed.

Jan 1, 1971

By Prohaska G, Jackson F, Jack B

To learn more about the fundamental roof behaviour in South African coal mines, accurate underground measurements of roof deflection were conducted in bord and pillar panels during development and pillar extraction. To conduct these measurements a survey levelling technique was adapted. The overall system reading accuracy was established as being within 0,4 mm on a 15 m sighting distance. The underground sites were modelled and, for a roadway development, similar symmetrical curvatures were calculated by a linear elastic model, as were measured underground. In a pillar extraction panel, a significant amount of bed separation was measured and the roof underwent an a-symmetric movement due to the close presence of the mined out area at one side of the roadway.

Jan 1, 1992

By Stewart R

Potential acid rock drainage from the destruction of metalliferous sulph-ides is recognised as a critical factor in the design and economics of any mining venture. While this realisation is relatively new, mining companies have embraced the issue with the aim of scientifically quantifying the magnit-ude of the problem, specific to indiv-idual properties.Coinciding with the development of the open pit mine at Porgera, a comprehensive assessment of the potent-ial for the formation of acid rock drainage was initiated in 1991. Detail-ed study of the mineralogical charact-eristics of all rock types, along with extensive test work to determine the maximum potential of rocks to generate and consume acid (known as acid base accounting or ABA), has been conducted. Correlating this with the known and interpreted geology of the open pit has indicated a strong relationship between rock type, sulphur content and the acid base character. This relationship is used daily as a simple, cost effective means for classification and management of the variety of material types produced from the minincx operation.

Jan 1, 1994

Longhole stope overbreak has always been a source of unwanted cost within the underground mining industry, and efforts to control it using various rock reinforcement systems have long been a rock engineering challenge. At the Pasminco Mining Broken Hill Operations trials have been carried out using an innovative cable bolt reinforcement system known as Rib-Roc. The system, based loosely on the Swedish Rib-in-Roc concept, utilises zones or ribs of heavily reinforced rock in the troublesome hangingwall and back areas of longhole stoping. The trials were carried out under a strict qualitative and quantitative scientific stope measurement program utilising rock mechanics instrumentation. Not only did the trial demonstrate the success of the system but data obtained was useful in implementing the system virtually as standard practice throughout the operation.

Jan 1, 1995

Vaal Reefs Mine annually produces some 75 tonnes of gold. Stoping operations, using a scattered mining method, are conducted on several reef horizons within Witwatersrand Supergroup metasediments of the Klerksdorp Goldfield. Current grades average 7.19 g/t Au over a 133cm stoping width. The reef horizons, of which the Vaal Reef is the most important, consists of 2.9Ga palaeoplacer deposits at the base of low angle unconformities. Typically, a reef comprises a mature quartz and chert conglomerate with a siliceous matrix and intergranular pyrite and carbon. Geologists are primarily responsible for underground mapping and supervising of drilling programs. To a lesser extent they are involved with sampling, grade control, ore reserve estimation, mine planning and rock mechanics. Due to a general decline in grades of gold mines, an escalation of production costs, and with the current weak gold price, it has become essential to improve production efficiencies. Consequently the role of the mine geologist has moved away from that of simply keeping the mining people "on reef'. Greater emphasis is being placed on refining geological models to assist in selective mining of the reef and investigations of secondary reef horizons are encouraged. Exploration within fault losses and re-evaluation of pillars is important, and geologists are becoming more involved with sampling and grade control exercises.

Jan 1, 1990

By Mahoney M

For gas content analysis in recent years, it has been standard procedure to report results on a 'dry ash free' (daf) basis, under the assumption that gas only adsorbs onto coaly material. In order to test the relationship between ash and sas content, samples of various rock types were taken from two drillholes in the Newcastle Coalfield. The results of this study confirmed the correlation between gas content and ash, providing an accurate means of relating gas contents for all carbonaceous rock types.

Jan 1, 1995

By Masszi D

INTRODUCTION The association of methane with coal has been known almost since coal was first mined and in general it has been considered the curse of underground coal mining. Historically, most of the effort to handle this methane has been directed at diluting it to a safe level and preventing an explosive mixture of methane and oxygen from forming in any part of the mine. This is generally achieved by in-mine activites. This approach has two principal drawbacks, the severity of which are dependent on local conditions. The first is that the activity associated with the handling of the methane is undertaken in the mine and there- fore competes with the mining activity for the limited space available. The second drawback is that the whole methane handling activity is generally a cost to the coal because methane is so diluted that it cannot be used. With the value of energy increasing thi; second drawback is gaining importance so th.u several mines in Europe and North America ;it,, now installing systems to recover the methane in a useful form. Two approaches are

Jan 1, 1982

By Muto S, Okada S

At Tamano Smelter, part of the furnace settler is electrically heated by electrodes placed internally. This practice provides good control of the settler conditions. The authors have been investigating improvements in furnace operations, especially to decrease the copper content in the slag discarded from the settler. The important operational points on the control of magnetite in liquid matte and slag are discussed on the basis of the thermodynamic calculation method developed by Prof. S. Goto. The behaviour of magnetite in the practical furnace has been studied by using a torsion magnetometer and a solid electrolyte oxygen-sensing cell.

Jan 1, 1980