Search Documents

When a thin film of volatile matter is deposited under vacuum on a polished coal surface, and the coated surface is examined microscopically in piano--polarized reflected light, colour changes are observed characteristic of the various macerals present. The colour changes appear to be mainly due to interference between light reflected at the upper surface of the film and at the film/coal interface. A variety of source materials for the volatile matter required have been tested, including powdered bituminous coal, coal tars, boron oxide, and certain resins.

Jan 1, 1969

Any project carries a number of challenges and risks. Inappropriate design, poor project management, time, industrial disputation and capital over runs are all areas which can impact on a project cash flows and return on investment. In the resource Industry you have the added complexity and risk of geology which is difficult to predict and sometimes unforgiving. The Dartbrook Mine was designed and constructed as a high output longwall mine and has overcome a number of hurdles to produce over 2.3 million tonnes for the first year of operation. A number of problems were encountered during construction which resulted in the inseam development being delayed for six months. Dartbrook people have demonstrated they can manage adversity and produce world class results. The mine has been through a very steep learning curve during 1997 and with this experience behind the mine is now producing at an annualised rate of 3.4 MTPA.

Jan 1, 1998

With the continued drop in export coal prices (as measured in US$) delivered to the Pacific Rim market, and a fixed annual 12 per cent increase in overburden, Usibelli Coal Mine Inc was faced with the need to reduce mining costs substantially or else forfeit its foreign coal contractual commitment which amounted to about half of annual mine output. Management made a difficult and fortuitous decision to proceed with an engineered plan to switch from a two seam, extended bench dragline operation to a two seam, cast blast and spoil side operation. While down-sizing and cut-backs became the rule in all departments of the mine, the drilling and blasting budget was more than doubled. Most will agree that this is contrary to what usually happens when a mine is faced with down sizing. The more common scenario would have management target the drilling and blasting budget for decrease as a first priority to cutting cost, and then later witness a decrease in equipment performance leading to an increase in the production cost per tonne. Although Usibelli Coal Mine more than doubled its annual drilling an blasting budget three years ago, the overall stripping cost has be, reduced by more then 37 per cent.

Jan 1, 1995

By Higuchi K

For the mechanisation or automation of mining, recognition of the shape of mined cavities is basic information. A three dimensional shape measuring system, developed and tested, includes an ultrasonic range finder which is attached to the tip of a serial link manipulator. The range finder can be moved to any position and direction in the operational space of the manipulator. The position of a point on the surface of the object is obtained from the position of the range finder, the direction of the beam of the ultrasonic waves and the measuring distance of the range finder.To avoid collision between the sensor and the object, the manipulator is controlled to trace the surface of the object For the tracing control, another ultrasonic range finder is employed. The test results show that the developed system has high performance.

Jan 1, 1991

The main objectives of this paper are to identify the main sources of coal dust and to investigate measures for minimisation of dust generated at these sources at the Bukit Asam open cut mine, on the island of Sumatera, Indonesia which uses a

Jan 1, 1994

Reverse circulation (R.C.) drilling or the dual tube method as it is quite commonly known, has a unique place in conventional mineral drilling. It can be classified half-way between open hole drilling at the lower end of the scale and diamond drilling at the upper end. The system basically consists of two tubes, one inside the other, with compressed air flowing between the inner and outer tubes. Sample cuttings return up the inner tube through the head of the rig and via a hose to a cyclone where the sample is collected. This system means that the cuttings are free of contamination as they are at no time in contact with the outside formation of the hole.Reverse circulation drilling is divided into two areas: R.C. Roller and Blade for softer formations; and R.C. Percussion for harder formations.

Jan 1, 1986

By Barrett D

The paper discusses the justification for the Open Pit Mining Operation at Central Norseman Gold Corporation Limited's North Royal facility.Open pit mining history is outlined together with production statistics and associated costs. Underground mining practice is discussed together with an outline of the problems with mining in oxidised ground.

Jan 1, 1984

By Gibson I, Somerville J

Three main confined aquifers occur in interseam sediments beneath the planned excavation for the Loy Yang Brown Coal Open Cut. Sub-artesian groundwater pressures occur in all aquifers necessitating dewatering to prevent excessive seepage and depressurisation to prevent heaving of the open cut floor and batter instability. Reduction of water pressures in coal joints is also required to maintain coal face stability. This paper describes the depressurization and dewatering strategies, investigation for and installation of pump bores and groundwater observation bores. Approximately 5000m of drilling is carried out annually for dewatering at Loy Yang and both cable tool and rotary flush drilling methods are utilized. The cabletool method is used to obtain accurate samples for laboratory analysis, whereas rotary flush methods are used for speed and for installation of the larger diameter pumping bores. A method of re-establishing pump bores after partial excavation during mine development has been successfully developed with large cost savings. Trials are also being conducted with pre-collaring of deep bores with rotary methods then sampling the aquifer strata with a cable tool rig.

Jan 1, 1988

By Sneddon A

Expansion of central production facilities at the Kutubu Petroleum Development Project in Papua New Guinea (PNG) required excavation of a steep hillside overlooking operating crude oil processing, storage and pumping facilities. Drilling and blasting were used to remove a large volume of rock which varied from hard limestone to soft sandstone, with zones of soft clay and many underground caverns. Similar ground conditions had made it very difficult to predict and control blast-ing results during previous excavation in this area.Special conditions of the project included restrictions on ground vibration levels at a high pressure oil pipeline and pump station within 100m of the blasting area, and a prohibition on any flyrock. As work progressed, some blasting was necessary with 20m of installations being constructed on the levelled project site. Thus blast design, drilling and charging were carefully controlled to avoid any incidents which could interfere with oil production or progress of the construction project.

Jan 1, 1994

By Yeliseyev AK, Shestakov AM

Comminution is the most power-intensive process in the technology for ferrous quartzite concentration. That is why improving comminution efficiency leads to the most appreciable economic effect on the concentration process. The trend towards reducing the lump size of crushed ore before charging the mill is considered to be of major importance in improving comminution efficiency. A considerable number of investigations have been performed in this direction. At the same time, a strong interest is also maintained in the increase of comminution efficiency due to optimisation of process taking place in the mill. Recently, investigations of the power intensity of the breaking process inside the mill have been carried out at the Krivoy Rog Mining Institute. It was ascertained that the routine conditions of comminution at a low mill ball charge ratio resulted in an unnecessarily high power consumption due to the force of impact of falling and milling bodies far exceeding the power required for comminution. For example, the power value for falling balls of 60 - 125 mm in diameter reaches 0.3 kNm, and the force and stress due to ball contact with the lining reaches 60 kN and 250 MPa respectively. These values exceed the force required for comminution by a factor of ten. Analysis of the mechanism of ore particle size reduction during comminution in the ball mill indicates that the size reduction is due to impact load, attrition load, and static load. The efficiency of size reduction is very low. During comminution in the ball mill, impact loads prevail and amount to 85 - 90 per cent of the total load. In this situation, not more than 10 - 15 per cent of destruction is due to attrition.

Jan 1, 1993

By Heinrich CA, Wall VJ, Walshe JL

The Porgera Gold Mine, located in the highlands of Papua New Guinea, has produced over 5 million ounces of Au, since its opening in late 1990. The deposit is located within Upper Cretaceous Papuan Platform sediments approximately 25 km south of the Lagaip Fault, and is spatially and temporally associated with the 6 Ma alkaline Porgera Intrusive Complex.

Jan 1, 1995

By Grady PO

The longwall panels at Clarence Colliery have experienced intermittent sudden weightings on the face that have caused some production delays. These weightings have typically been more severe on the wider faces. A program of surface subsidence and extensometer monitoring was undertaken above Longwalls 4 and 5 to investigate the behaviour of the overburden strata during longwall extraction on two faces of different widths.The monitoring indicated that a dome shaped zone of large downward movement extends up into the overburden strata to a height equal to about the panel width.

Jan 1, 1998

By Russo S

Metals Refining Operations Pty Ltd (MRO) began refining gold in PNG in 1991 and has undergone continuing growth since then in servicing an everchanging and growing market. MRO's ownership combines PNG Government interests and Golden West Refining Corporation Limited as operator.Features include a very diverse range of suppliers, a full range of technical methods and challenges and the financing and marketing responses unique to a developing country. These areas are examined and documented with special emphasis upon the service needs for the gold industry and future trends and challenges are discussed.

Jan 1, 1997

This paper presents a summary of the technical achievements of the Port Pirie Smelter in 100 years of lead smelting and refining. It also aims to give where possible the reasons or circumstances that led to the achievements. The major achievements took place in the areas of sintering, blast furnace, copper drossing, copper recovery, lead refining and slag fuming.

Jan 1, 1989

Magneto flotation is a recently developed method aimed at simultaneous utilisation of the magnetic and flotation properties of minerals in separation processes. In this method, magnetic minerals are prevented from reporting to the froth product while non-magnetic minerals are being floated. With suitable ores, this makes it possible to reduce or entirely eliminate the cleaning and scavenging operations that are otherwise necessary in conventional flotation and magnetic separation systems. This paper describes the testing of magneto flotation on a Canadian magnetite ore. The ore sample used in the experimental work contained a total of 32.89 per cent Fe of which 87.60 per cent was magnetic in the form of magnetite. Magnetoflotation yielded, in a single step, a final concentrate assaying 69.10 per cent Fe and with an overall recovery of 84.84 per cent representing a magnetic iron recovery of 96.39 per cent. Comprehensive comparisons were made with conventional magnetic separation and flotation, and it was found that with these methods at least four processing steps were required to achieve results similar to those obtained with single-stage Magnetoflotation.

Jan 1, 1993

This paper examines the various stages of development and design work which were necessary to develop the cemented rock fill system for copper mining at Mount Isa. The reason for a cemented sand fill development program together with details of the test work undertaken are briefly outlined. The testwork associated with the selection of a suitable local rock to supple- ment the cemented hydraulic fill is discussed, as is the method for underground placement and mixing of the graded rock with the cemented hydraulic fill. The design features of the final system which incorporates a graded rock handling system and a cemented hydraulic fill reticula- tion system is outlined.

Jan 1, 1973

The explosion of a charge in a drillhole sets the surrounding rock mass into vibrating stress wave motion. Except in the immediate vicinity of the drillhole, the dynamic stresses associated with this motion do damage only to pre-existing joints, cracks, or other weak planes, not to the rock material in between these. The joints are weak in tension, therefore the damage occurs as a result of tensile stresses. The initial damage process in the rock mass that ultimately breaks loose in front of the hole is similar to that in the remaining rock behind the drillhole. Recorded or calculated values of the vibration velocity and frequency contain a wealth of information about the combination of stress and strain that causes the damage. This paper outlines a new technique by which the peak strain energy derived from measured or calculated vibration velocity records is used to determine the local fragment size distribution. It combines two previously known and well tested techniques, namely the Holmberg-Persson calculation of the peak vibration velocity generated by an extended charge and King's calculations of the fragment size distribution as a function of the strain energy in rock crushing. Both of these calculations are based on experimental data and have been tested and found to agree well with actual conditions in their respective fields. Holmberg-Persson's calculated peak vibration velocities have been used successfully to predict and control damage to the remaining rock in cautious blasting, while King's calculation successfully describes the comminution of rock in mechanical crushing. Preliminary predictions of fragmentation in two types of rock blasting, a large hole open pit mining blast and a tunnel round, indicate that the new technique for fragmentation prediction has the potential for predicting fragment size distributions within the rock removed by the Blast.

Jan 1, 1995

A good blasting result is largely achieved by putting the right amount of explosive in the right place and firing it in the right sequence. The best blast design in the world will not break the rock if the planned blast layout is not achieved in the field. One of the critical inputs into a blast design is the diameter of the blasthole. An assumption that the actual blasthole diameter is equal to the nominal drill bit size is generally made. However, a small deviation in the actual hole diameter from that assumed will have a dramatic effect on the hole's volume and, consequently, where the explosive is placed in the blasthole. Any discrepancy in actual blasthole volume from that assumed will be reflected in 'overloading' or 'underloading' of the blasthole with the calculated explosive quantity and, thus, reflect in explosive distribution and stemming lengths. When loading to a 'collar' in an oversized hole extra explosive will be used, resulting in higher than planned powder factors and explosive costs. A blasthole diameter assumed from a nominal drill bit size is an incorrect assumption. This paper will present some actual blasthole diameter measurements illustrating the variation in hole diameters seen in the field and proposes a practical method for achieving a useful blasthole diameter measurement.

Jan 1, 1990

By Butters S. E, Deslandes J. V

The selection of loading and haulage equipment in a proposed or oper- ating mine is vital in ensuring the cost effective achievement of produc- tion targets. To assist in the evaluation of different haulage systems, a truck haulage simulation model has been developed at BHP Melbourne Research Laboratories. The operation of the model is described and exam- ples of an actual application at Mt. Whaleback Mine is presented.

Jan 1, 1989

By Lee Y. K, Walker G. S, Bronswijk V. W

The effect of leaching three samples of Mt Weld ore with a-hydroxysulphonic acid [(CH3)2(COH)SO3H] was assessed. Apatite present in the samples was found to be readily soluble but calcination up to 600¦C was required to increase the solubility of crandallite. Increasing the calcination temperature increased dissolution of both phosphate and alumuuum. The optimum SO2 content in solution for the dissolution of crandallite ores was found to be lower than for apatite.

Jan 1, 1991