Search Documents

By Catalin Florin Petre, Elahe Ghasemian Langeroudi, Abdelaaziz Azizi, Éric Proulx, Caroline Olsen, Paul Blatter, Faïçal Larachi, Claude Gagnon

"The recovery of gold from ores is often accompanied by the release of other species in the leach solution. This state of affairs leads to depleted free cyanide levels in the slurry. Therefore, separation and quantification of these cyanicides and free cyanide at different stages of the cyanidation process as well as in waste solutions is crucial to provide mitigation tools by preventing leaching of deleterious metals for environmental considerations.COREM and the research group of Prof. Larachi have been working together on the control of gold passivation and cyanicides during cyanidation for several years. Previously, a first capillary electrophoresis (CE) protocol for the speciation of sulfur and cyanicides (SCN-, Cu, Fe) during cyanidation of gold complex sulfide ores was developed and validated for assessing industrial process water.The separation of zinc cyanide complexes used to be confronted with a number of difficulties due to the weak and/or undetectable cyanocomplexes in formally available CE protocols. Moreover, according to our knowledge, no direct CE protocol exists to separate free cyanide. Therefore, a new study aimed at developing a second CE protocol for the detection and quantification of cyanide complexes of zinc and nickel as well as of free cyanide in the cyanidation process water.To achieve this goal, six common carrier electrolytes such as pyridine, trimellitic acid, 4-methylbenzylamine, sodium chromate, phthalic acid and tris base were studied, using an indirect UV detection method. The best results were obtained using sodium chromate for which all ions were successfully separated and quantified. In addition, the effect of electric field strength, injection volume, electro-osmotic flow (EOF) modifier and background electrolyte (BGE) concentration were examined, while peak height, peak area and noise were considered for optimization.As a result, the new protocol is expected to complete the initial CE protocol by detecting cyanide complexes of zinc and nickel as well as free cyanide. Moreover, analytical determination of free cyanide in the presence of weak cyanide complexes achieved by the new protocol was also compared to conventional titration using silver nitrate solution. This new CE protocol will contribute to applied research and help plants to better understand and eventually control the behaviour of cyanidation circuits."

Jan 1, 2011

By Filipe Beretta

This study investigates geophysical logging capacity to predict coal quality. It was analyzed for possible correlation, some parameters determined via laboratory analysis of coal against results for the same parameter derived from wireline logs recorded by a geophysical probe. These probes detect variations in some rock physical properties, such as their natural gamma ray emissions and electrical resistivity. Results showed a strong correlation between natural gamma and ash content, establishing a linear model to estimate ash content from geophysical logging data with a low estimation error (less than 5%). Besides, results showed that there is no correlation between sulphur content or volatile matter and resistivity, neither with natural gamma of the rocks. Ash content derived from gamma ray values can be used as secondary information to evaluate coal quality during resources estimation, using methods such as soft indicator kriging. The methodology is illustrated using a case study at a coal deposit in south of Brazil.

Oct 1, 2009

By James A. Finch, Stéphanie Gélinas

"A colorimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determination in a series of industrial campaigns. Some frother observations are described, including: concentration evolution down a bank, distribution between pulp and froth phases, and a mass balance around a circuit. Minute amounts of frother in recycle water were also measured.The contribution of frother and alcohol by-products in the analysis was generally additive for plants using aliphatic alcohol type frothers and decoupled for systems using glycols. Typically, U250C (polyglycol) was used at higher concentration (>10 ppm) than MIBC (aliphatic alcohol) (<10 ppm) or F-150 (polyglycol) (<3ppm).The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimization of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimize the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.INTRODUCTIONOwing to the lack of analytical methods, the task of determining frother concentration in plant flotation circuits is not routinely performed. Industrial sites seldom outsource analyses that are both costly and inconvenient, due to the necessity of shipping freeze-dried samples to remote testing facilities. A more direct colorimetric method has recently been demonstrated for the laboratory characterization of common industrial frothers (Gélinas and Finch, 2004). The approach, based on the Komarowsky reaction (Penniman et al., 1936; Coles et al., 1942; Duke, 1947), was previously described by Parkhomovski et al. (1976) for methyl iso butyl carbinol (MIBC). The reaction involves the interaction of the OH group of a higher alcohol, concentrated sulphuric acid, and salicylaldehyde, to yield coloured solutions with intensities that can be analyzed by UV-visible spectrophotometry."

Jan 1, 2007

By G. Stokreef, B. R. Davis, M. Kadiyski, Alvear Montenegro, H-P. Loock, V. Montenegro

An optical probe for burner monitoring in copper flash smelting, first developed at the University of Concepcion, is being industrially tested in a collaboration between Kingston Process Metallurgy, Aurubis AG, and Queen’s University. The sensor uses fibre-optics and optical emission spectroscopy to analyze the light emitted from combusting particles in the furnace reaction shaft. Information that can be extracted from the emission spectrum includes the temperature and brightness of the flame, as well as emission lines or bands from excited atomic and/or molecular species. Laboratory proof of concept testing of the sensor was first completed in a continuously fed drop tube reactor using O2/S stoichiometric ratios between 0.8–4.0. These O2/S stoichiometries capture the industrial operating condition, which is typically less than 1. The results from lab testing justified a plant trial of the optical probe, which was done in the Aurubis Hamburg flash furnace in September 2018. From this trial, approximately 31 hours of spectral data were collected and synchronized with furnace operating data. The results from both drop tower test work and the plant trial are discussed with implications for process monitoring in the commercial furnace. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process. It is used to treat copper sulphide concentrates and small amounts of secondary materials, such as dust generated by the process. O2 enriched air and the concentrate blend are fed into the furnace reaction shaft through the concentrate burner. As the particles fall through the reaction shaft, they heat up and ignite, causing rapid, exothermic reactions that oxidize the iron sulphide, some copper sulphide and impurities in the feed. Reacted particles fall into the settler of the furnace, melt and separate into a matte and slag, while the SO2 enriched off-gas is carried out of the furnace for heat recovery and H2SO4 production. Operation of the furnace is achieved by adjusting a limited number of control variables. The main variables are the blast feed rate, blast oxygen enrichment, SiO2 flux feed rate and CH4 combustion rate (CH4 is used when the chemical energy of the concentrate is low) all measured relative to a set feed throughput. (Davenport & Partelpoeg, 1987; Davenport, King, Schlesinger & Biswas, 2002) The batch tapping nature of flash furnaces makes operation difficult because these control variables impact each other, and product quality can only be measured when matte and slag are tapped from the furnace. This means that operation of a furnace is based on feedback control from matte and slag assays. Because of the time-delay associated with understanding product quality, there is interest in using technology to monitor the combustion reactions that happen in the furnace reaction shaft.

Jan 1, 2019

By Jr. Blanchette, Claude Bazin, Paul Blatter

"Reporting of the gold production during a month implies to estimate the mass of gold that is processed by a mill, recovered as dorés, lost to the tailings and the change of gold inventory within the plant equipments. Carbon in pulp and/or carbon in leach tanks may contain gold inventory as large as 72 000 g (2 200 troy oz) of gold which needs to be estimated from measurements obtained from sampling the material contained in a tank. Sampling and analysis introduce measurement errors that could be systematic and/or random. This paper examines the effect of measurement errors on the estimation of the gold inventory and on the variation of the inventory in the carbon in leach tanks of the Agnico-Eagle Mines Limited Lapa concentrator. Results of the analysis demonstrate that the inventory is measured with ±10% reproducibility, while the variation of inventory used for mass balance is known with ±300% reproducibility.INTRODUCTIONThe preparation of a production report implies to reconcile measured data with the constraint of material balance over the considered period of production. The sampling and data reconciliation problems were recently reviewed by Morrison (2008) and Jansen (2009a; 2009b). Typically a production report is prepared to cover a period over which the mass conservation hypothesis can be considered valid. In gold processing plants, the change of inventory can seldom be neglected and plays a significant role in material balance calculations. This is particularly true for circuits using carbon adsorption, where the complete cycle of carbon is measured in days.In a 2000 t/d gold ore processing plant, the inventory can be as large as 140 000 g of gold in gravity concentrator bins, carbon in pulp tanks and in the electrolysis circuit. This is equivalent to the mass of gold that fed the circuit during 10 days of operation with 7 g/t feed assays. The change of inventory may therefore strongly impact the production figures and especially the plant recovery at the end of a week or a month. Despite the financial impact associated with gold inventory, few publications are devoted to the subject. Bruington (1991) and Morrison (2008) discussed the problem and stressed the need for the development of reliable methods to estimate the gold inventory in carbon in pulp or carbon in leach circuits."

Jan 1, 2011

By Tony Moore, Peter Riccio

"MMG (Minerals and Metals Group) operates the LXML Sepon’s mineral processing facility located 40 kilometers north of the town of Sepon, in the Savannakhet Province, Lao PDR. The Sepon copper plant produces 70,000 tons/year of LME grade A copper cathode using leachautoclave- SX/EW-flotation technology (Baxter et al., 2003). Pyrite recovery in the flotation circuit is critical to the operation, as it is used to generate acid and soluble ferric ion for the leach circuit. Low pyrite recovery has been an on-going challenge in the flotation circuit. Final tailings characterization work done by Ian Wark Research Institute (Bassell et al., 2006) showed that the pyrite losses to the tailings are made up of a combination of coarse liberated particles and finer particles that have been coated by clay fines.In December of 2005, a joint Cytec-MMG technical program was initiated to address the pyrite recovery issue. A series of diagnostic tests were performed in the Cytec Stamford Research Facility using synthetic plant water showing that the collector was precipitating as a metal salt and was unavailable for mineral attachment. The tests also identified several collector chemistries that would likely be robust in the low pH (< 1), high dissolved metal ion environment and will not complex with metal ions in solution. With the support of the Sepon on-site engineers, an extensive, successful laboratory program was completed, which was subsequently followed by on-plant testing that showed a step wise improvement in pyrite recovery.INTRODUCTIONLow pyrite recovery has been an ongoing problem in the flotation circuit at Sepon. Sulfur recovery (indirect measure of pyrite) was improved from 40% to 65%-75% in mid-2005 when on site laboratory work confirmed that AERO® 8045 Promoter was a more effective collector then AERO® 407 Promoter. However, sulfur recoveries above 65% could never be achieved. Sepon requested the Ian Wark Research Institute to complete a surface analysis study using Scanning Electron Microscopy, X-ray Photoelectron Spectroscopy, and Time-of-Flight Secondary Ion Mass Spectroscopy to determine if clay coated pyrite played a role. It was concluded that the pyrite losses to the tailings are made up of a combination of coarse (+ 100µm) liberated particles and finer (-74µm) particles that have been coated by clay fines. The majority of the losses appear to be due to the former. In December of 2005, a series of diagnostic tests were performed in Stamford using synthetic plant water in order to identify what chemistries would likely be robust in the slimy low pH and high dissolved metal ion solution environment. Results showed that several chemistries would not complex with ferric, ferrous or copper in solution and therefore should perform well in the Sepon flotation. The incumbent collector, AERO® 8045 Promoter was complexing with metal ions in solution. This resulted in the collector not being available for adsorption onto pyrite."

Jan 1, 2011

By J. Dong

"Xanthate is a sulfide collector that has been widely used in flotation for almost a century. It is inexpensive, easy to synthesize and apply, and produces good metallurgy in the right applications. However, a major drawback of xanthate is that it decomposes easily and generates CS2 gas in transportation, storage and operation, which can be harmful to human health. Also, excessive xanthate in tailings pond leads to toxicity of the process water and potential damages to aqua-life systems. New regulations in Ontario require that the TWA (time-weighted-average) value of CS2 in the work place is below 1 ppm, which is 1/10 of the previous limit. The stringent regulation may eventually sweep other regions of Canada with the increased awareness of healthy working conditions and environment protection. Therefore, it becomes very important to find xanthate replacements which will be “green”, i.e., environmentally friendly.In this research work, a systematic procedure is used for collector evaluation using the Sudbury nickel sulfide ores from Vale’s Ontario operations, starting with the collector properties (MSDS) evaluation, followed by batch flotation tests, miniplant tests, plant trials and economic evaluation. It is found that the most promising xanthate replacement is dithiocarbamate.INTRODUCTIONSulfide mineral flotation has been practiced since the early 20th century. Its industrial importance is well recognized as mineral concentrates from flotation can be economically smelted and refined to provide primary metals. Collectors play a vital role in froth flotation. There are reagents possessing both a polar group that binds them to the mineral surface and a nonpolar group that is oriented away from the surface to attach air bubbles. The introduction of xanthate as a sulfide collector in 1925 was a remarkable development in froth flotation (Keller, 1925). It is low cost, easy to synthesize, water soluble, simple to control in application. Most importantly, it has strong capability and usually good selectivity for sulfide mineral flotation, which have been keeping its application prominent for almost a century."

Jan 1, 2011

By Kim Le Roux

Cemented paste backfill (CPB) is a relatively new material that is increasingly being used in open stope mining across the world. The advantages offered by this high density tailings backfill include: a lower total cost associated with backfill placement, reduction of excess water underground; and the elimination of the need to process the tailings prior to placement. However, almost all backfill design is based on the performance of laboratory prepared samples since it is difficult to obtain undisturbed samples and conduct in situ testing due to the lack of access to backfilled stopes and the safety concerns in accessible areas. The logistical problems associated with conducting in situ testing and obtaining undisturbed samples of cemented paste backfill (CPB) has lead to the reliance in the mining industry on performance data obtained from laboratory prepared CPB samples. The degree to which these laboratory prepared samples represent the actual in situ condition is not well defined, partly because the influence of the mixing, transport and placement process on the material properties it is not well understood. Therefore, there is a need in the industry to understand how the material properties and hence the performance of the laboratory prepared CPB compares with in situ material. This paper reports the findings of an investigation into the in situ properties of CPB at a gold mine in Northern Ontario. A combination of in situ and laboratory testing, conducted on undisturbed samples, was used to quantify the in situ properties and performance of the CPB. These results were then compared to those of a laboratory based investigation of the same CPB. It is evident from this investigation that the bulk properties of the in situ CPB are different from those of the laboratory prepared CPB. The most significant observed differences are that the in situ CPB has a higher void ratio and a lower degree of saturation than the laboratory prepared material. The implication of these differences on the stability and performance of the CPB will also be explored in this paper. 1

May 1, 2002

By C. S. Maggs, L. Shwydiuk, H. W. Newcomen

The southwest wall of the Lornex Pit at the Highland Valley Copper mine has been experiencing slope displacements since 1978. Measures to manage the displacements on previous pushbacks have included stepping out, scheduling pushbacks to unload the crest of unstable areas, slope dewatering and mining with intensive slope monitoring. The final pushback on this wall is currently being mined and substantial modifications to the slope geometry could prove to be uneconomical. As a result, a campaign of surface water collection and diversion, horizontal drainhole drilling and deep well drilling is currently underway to maintain an acceptable degree of stability to the end of mine life. The various factors contributing to instability, including engineering geologic controls, rock mass strength, and surface and groundwater hydrology are presented. Movement trends, displacement magnitudes and stability analyses results are also discussed.

Jan 1, 2003

By Michel Brissette

"To recover more valuable ore and considering the complexity of minerals, the needs to grind finer is increasing. To reach the desired fine grinding targets, using the existing grinding media size, the energy consumption is increasing exponentially. As already proved at this conference, small grinding media represents the best potential to improve grinding efficiency. How do the small grinding media perform in industrial grinding mills?The use of small grinding media in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, smaller grinding media versus 25 mm media generate a power saving from 10% to 44%. In vertical stirred mills, the power saving increases from 20% to 60%. More potential savings have been identified.For the same operating conditions, how a vertical stirred mill is performing compared to ball milling? In regrind application, a vertical stirred mill with small media (5-12 mm Millpebs) will require at least 62% less energy than a ball mill charged with 25 mm grinding media.INTRODUCTIONIn some mining applications, fine grinding is needed to liberate further the valuable ore. The purpose of regrind mills is to achieve the last stage of grinding before final flotation stage: the cleaners. In part because of high prices of small grinding media as well as availability, the most widely used size of grinding media is 25 mm.When calculating the recommended ball top size from Bond’s formula (Bond, 1961), the size for regrind applications is much lower than 25 mm. Today, the barrier for small grinding media is broken. They are best suited in regrind application. The size of grinding media is one of the most important variables affecting the mill efficiency (McIvor, R., 1997; Nesset, J.E., Radziszewski, P., Hardie, C. & Leroux, D.P., 2006).Conventional ball milling was discarded for fine grinding because of its very poor energy efficiency (Zheng, J., Harris, C.C. & Somasundaran, P., 1994; Yan, D.S., Freeman, M. & Dunne, R., 1995). Therefore, new technologies as stirred mills were developed to grind finer more effectively. Three fundamental questions should be asked. What is the best fine grinding technology? What should be the best media size to use? Is it possible to grind finer by using less energy with the existing regrind equipment?"

Jan 1, 2009

By Jim Truskoski, Alain Bouchard, Andy Kerr, Germain Labonté, Jim Barrett

"Improving mill grade recovery relationships is always good business. INCO’s Clarabelle Mill has just undergone a $16 million process upgrade that was designed to improve nickel recovery by 2%. The “Mill Redesign Project” was completed on time, under budget and delivered the promised improvement in recoveries.This paper describes the methodology of the Mill Redesign Team, details of the process improvements and the critical success factors that helped the team deliver on its promises.With a payback of under one year, the Mill Redesign Project will play a key role in ensuring a competitive edge as INCO embarks on its second century of operation.INTRODUCTIONIt is not uncommon in milling operations to encounter a crisis. That is the point when the process does not behave as expected and fails to respond to the increasingly desperate efforts of the metallurgists and operators. Flowsheet and process changes are attempted and abandoned. With luck, one or more of the changes achieves some mitigation of the original problem or more usually, the original cause of the problem disappears. Regardless, the metallurgist can sit back and bask in the apparent success of his or her endeavours.Less common is when a problem is carefully diagnosed, a team put together to explore all avenues and recommend a path of action that is implemented on time, on budget and immediately delivers on the promises which are sustained over time. This is one such story. It is the story of the Mill Redesign Project at INCO’s Clarabelle Mill in Copper Cliff, Ontario.BACKGROUNDThe Clarabelle Mill was built in 1971 on the southern rim of the Sudbury basin. At that time it was one of four mills operated by INCO in the Sudbury area. During the 1970’s, 80’s and 90’s, the need for increased process efficiency, higher levels of sulphur rejection to tails and the concurrent development of high capacity mills and flotation cells, resulted in the consolidation of INCO’s Sudbury area milling operations into a single, expanded facility at Clarabelle."

Jan 1, 2003

By James Anstey

BHP Billiton?s Cannington facility is a mining and minerals processing plant near Mt. Isa in Central Queensland, Australia, producing silver, lead and zinc. Mine ore is processed in a concentrator, which consists of grinding, flotation, thickening and filtration. Grinding is carried out in a fully autogenous (AG) mill. The mill operates in closed circuit with a pebble crusher. Throughput is approximately 380 tph. Cyclone overflow from the grinding circuit is fed into a flotation circuit for the recovery of lead, zinc and silver. Two concentrates are produced (lead and zinc), which are then thickened and filtered. The filtered concentrate is transported by road to a rail receiving station. From here the concentrate is railed to port in Townsville for shipment to the smelter. Matrikon and Engineers at BHP Billiton?s Cannington Mine have used ProcessACT to develop a flexible, nonlinear dynamic simulator for the grinding circuit to further enhance process understanding, as well to investigate various optimization strategies. An online charge volume estimator was also developed for the AG mill to aid in the understanding of overload conditions, which for the previous two months had been the primary contributor to downtime. The models were developed using a combination of first-principles modeling along with input-output dynamic responses. Examples of models used include: Morrell ?C? model for power and charge shoulder/toe angle prediction; Whiten?s mixing model for breakage and hold-up; Nageswararao cyclone model for predicting cut size; slurry recovery and water recovery. The composite model simulates system dynamics starting from the stockpile reclaim system and finishing at the feed for the flotation process. The objective was to provide a tool that assisted Cannington in understanding their Grinding Circuit and allowed them to develop and evaluate circuit optimization strategies. BHP Billiton Cannington Mine is now considering development of a Grinding Circuit Optimizer utilizing the models developed for the simulator.

Apr 1, 2005

By M. Cai

A practical simple method is proposed to estimate the tensile strength (st) of strong brittle rocks from the strength ratio of R= sc/st = 8 sc/sci, where sc is the uniaxial compressive strength and sci is the crack initiation stress in an uniaxial compression test. 8 is the Griffith strength ratio and the term sc/sci accounts for the difference of crack growth or propagation in tension and compression in uniaxial compression tests. sci can be reliably obtained from volumetric strain measurement or acoustic emission (AE) monitoring. With the strength ratio R determined, the tensile strength can be indirectly obtained from the result of uniaxial compression tests. In addition, a practical estimate of the Hoek-Brown strength parameter mi is presented and it is suggested that mi = 12 sc/sci can be applied to strong, brittle rocks in high confinement zone and mi = 8 sc/sci can be applied to low confinement to tension zones. It is found that the predicted tensile strengths and Hoek-Brown strength parameter mi using this method are in good agreement with test data. The rock strength parameters like st and mi, which require specialty tests such as direct tensile (or Brazilian) and triaxial compression tests for their determination, can be reasonably estimated from uniaxial compression tests.

May 1, 2009

By Ike Isagon

Backfilling has become an integral process in underground mining operations, with varying cost-effective forms of application. This study is a part of an overall investigation into the backfill practices at Copper Cliff North Mine (CCNM). The mine is well-diversified in terms of backfill methodologies and practices. The mine employs different fill methods such as cemented and un-cemented rock fill, slag fill, and cemented hydraulic fill (or a combination of them) in order to fill the voids created by mining activities. The history of backfilling at CCNM has been dominated by cemented and un-cemented slag fill. Each fill method requires operating and engineering guidelines for a cost effective quality control system. The purpose of this paper is to briefly discuss the backfill methods and applications, operating guidelines, and engineering requirements at CCNM.

May 1, 2011

By Ish Grewal

The ACACIA Reactor - Introduction What is it? The Acacia Reactor is a fluidized bed high intensity cyanide leaching system. Purpose for its existence? The Acacia Reactor was developed to treat high grade gold concentrates generated from primary gravity concentration systems. Why intensively cyanide leach a gravity concentrate? Current secondary upgrading processes, such as tabling, create significant losses of fine gold that is initially recovered in the primary gravity concentration units. Additional benefits include improved security and a reduction in health hazards associated with calcining.

May 1, 2002

By James F. Archibald

In historic mining practice, typical thin liner support systems have been considered to comprise non-reinforced or mesh-reinforced shocrete linings. In the early 1990?s, development of alternate forms of liner systems was initiated in Canada which is now undergoing significant international growth in countries which sustain major mining activity. Now internationally designated as thin, spray-on liner systems, a wide spectrum of liner materials, ranging from liquid/liquid to liquid/solid component combinations, has become commercially available. This innovative family of products is characteristically identified as being rapidly deployable, capable of creating ultra-fast setting coverage over rock surfaces, and able to develop tenacious adhesion and pull strength capacities for resisting rock falls and movements. This paper presents a summary of current liner developments and use in principal mining districts world wide. Additionally, a database of material properties for principal product types used in mining and a review of common quality control testing procedures under development are provided. Such information is based upon recent Canadian and international efforts being taken to assess and develop user standards for the implementation of thin, spray-on liners as rock support in mines. This work is intended to continue for a period of years, with the eventual goal being to establish support and installation guidelines for mines based on quantifiable laboratory and field research.

May 1, 2002

By F. Stober, D. Wanblad, J. Ndlovu, L. R. Nelson, L. P. S. de Villiers

The single six-in-line furnace of the Polokwane Smelter is the largest installed high-intensity furnace for platinum group metals (PGM) base metals sulphide smelting in the world. The furnace employs state-of-the art technology to deliver a planned throughput of 650 000 t/a dry concentrate at a design 68 MW power input. This furnace, at double the capacity of previously existing PGM furnaces, offers low unit operating and capital cost through the resulting economies of scale. Key features of the design include:

Jan 1, 2005

By D. L. Putnam

Snap Lake Mine ?? Complex dyke ore body ?? Underground operation ?? 1.1 million tonnes per annum ?? 1.2 carats per tonne ?? On-site diesel power generation ?? Supply by ice road and air ?? Milestones ? Construction commenced in 2005 ? Commissioning 2007 ? First diamonds August 2007

May 1, 2008

By Dave Bulled, Chris Bennett, Glenn Kosick, Glenn Dobby

"Mining companies around the world are embracing geometallurgical modeling at a rapid rate, as senior executives realize that inputs must be properly measured if the output is to be managed effectively. Geometallurgical modeling is used to scientifically manage risk in project evaluation, for plant design and production forecasting, and optimization of production planning and mineral processing/metallurgical unit operations. The technology also provides a solid foundation for implementing broad corporate strategies with respect to intelligent asset utilization and metal sales. Over the past five years, MinnovEX Technologies Inc. has been actively engaged in developing, promoting and applying geometallurgical modeling technology for major mining companies around the world. This paper describes the methodology for successfully applying the technology for the unit operations of comminution and flotation in the mining industry.INTRODUCTIONGeometallurgical modeling (referred hereon as geomet modeling), in theory, can be applied to its full potential on all unit operations in mineral processing; however, this paper will concentrate on two of the largest unit operations, namely comminution and flotation, where the technology is actually being practiced by many large mining companies. For concept studies and prefeasibility studies, aspects of geometallurgical technology are regularly applied but in a less rigorous manner than for final feasibility studies where justification for funds is sought. This paper will focus on the final feasibility stage of a project and on existing operations or planned expansions, where the full power of geometallurgical technology is brought to bear in a cost effective manner.One of the unique aspects of geomet modeling, when used to its potential, is the ability to design plants, and forecast and plan production with a quantifiable degree of precision, something that was unattainable in the past. This means that when new comminution and flotation plants are designed, the mining companies and financial institutions involved in the project can measure the precision of the design and therefore better understand and manage project risk. It means that for existing and new operations, metal sales personnel can carry out their sales strategies with a much better understanding of the degree of error associated with production forecasts of concentrate/metal and quality of concentrates. For mine and mill managers, geomet modeling allows the effect of the mine plan on the downstream processes to be quantified; thereby allowing the mine plan to be recast in a more optimized manner. Finally, existing concentrator personnel can optimize their unit operations based on a more definitive understanding"

Jan 1, 2004

Taking Up the AFN Corporate Challenge ?? About MAC ?? ?Towards Sustainable Mining? ??Mining and Aboriginal Peoples Framework ?? AFN-MAC Relationship ?? A New MAC Northern Initiative ??Social and Economic Progress ?? A View to the Future?

May 1, 2009