Search Documents

By Tapiwa Chenje, Victor Olivas, Peter Radziszewski

"Ore breakage and grinding media wear have always been considered and determined separately in laboratory tests. However the two processes are linked with the ore broken down in any comminution device being responsible for the majority of the steel wear experienced. The Comminution Dynamics Laboratory (CDLab) successfully developed a test methodology that can more accurately predict grinding media wear in tumbling mills than the Bond Abrasion test. This paper looks at the possible application of the abrasive wear methodology to determine breakage parameters of the same ore used in the abrasion test. Results indicate that breakage parameters comparable to t10 can be determined using the Steel Wheel Abrasion Test (SWAT), while using significantly less ore than standard breakage tests.BACKGROUNDThe Rubber Wheel Abrasion Test (RWAT) is an internationally accepted and widely used method for determining the abrasion wear behavior of materials. The abrasion wheel test was developed to primarily utilize a steel wheel (Brinell, 1921). Haworth (1949) criticized using of the steel wheel by arguing that increasing the contact area size in the steel wheel test causes a change in the wear rate with time. He suggested that the use of a rubber wheel instead eliminates this problem, leading to the adoption of the RWAT which was standardized in ASTM G65 (2004).Radziszewski (2002), however, found that the use of the Steel Wheel Abrasion Test (SWAT) was more applicable for wear testing in the mining industry for two critical reasons. Firstly, the major cause of wear in a ball mill, the most frequently used comminution device, is ball-ore-ball contact and also ball-ore-liner which both are metal-ore-metal contact. Therefore, using the steel wheel has the advantage of providing a similar abrasive environment to the one that takes place in a real ball mill. Secondly, the SWAT creates the potential of running experiments at much higher force regimes that are closer to what happens in actual mills, unlike the RWAT which is a low stress test."

Jan 1, 2011

By Yannis Faitakis, Simon Bergeron

"This paper describes the implementation of model-based predictive control (MPC) on a vacuum heat exchange network at Alcan's Jonquière Complex. The plant produces alumina from bauxite ore using the Bayer Process.The MPC system was commissioned in 2000, by Alcan personnel and an Advanced Control Engineer from Matrikon. The application has achieved an uptime of about 97%.The benefits were:• Energy savings : 0.5% - live steam reduction• Reduced variation: standard deviation of key temperatures reduced by 50%• Plant throughput increase: via the automated use of surge tanks• Decreased supervision time: by plant operations• Faster and easier diagnosis of problems and plant constraintsThe benefits were higher than expected with a payback time around 12 months.The purpose of the vacuum heat exchange network is to recover energy from a hot stream (pregnant liquor) by transferring it to a cold stream (spent liquor). The system is very tightly coupled, and the main constraints of the multivariable control system are: • to control the many tank levels involved in the process (8 tanks)• to maximize the temperature of the heated streams (spent liquor)• to prevent cooled streams (pregnant liquor) from cooling to below a minimum temperatureThe system includes 9 manipulated, 14 controlled and 2 feedforward variables.The advanced control implementation runs under an expert system environment and provides added flexibility to the overall control strategy."

Jan 1, 2003

By Gregg S. Hill, Bert J. Huls

"This paper on coarse particle recovery (CPR) summarizes a process to capture coarse particles that are not recoverable by regular flotation. Several porphyry copper operations in the world operate analogous circuits that recover non-floated copper from tailings; however, the case presented here is unique in that extensive underlying test work has allowed us to elucidate some fundamental principles behind recovery enhancement. This paper discusses an overview of the flow sheet that is proposed to Minera Escondida Ltda., the nature of copper in the feed to the CPR circuit, and the various unit operations within the recovery circuit. Details of the technology behind each unit operation will be presented in later publications.INTRODUCTIONSince 1996 BHPBilliton and MEL (Minera Escondida Ltda.) have developed a process to recover copper from coarse particles in the rougher tailings. Copper recovery from fresh tailings is not new. Several operations in Chile, such as Chuquicamata, El Teniente (AMEC, 2003), Mantos Blancos and others have operated various forms of tailings circuits. Both Chuquicamata and El Teniente practice cascade flotation scalping off froth containing fine copper particles after allowing sufficient retention time, air inducement and, sometimes, additional reagent addition. Chuquicamata tailings are not segregated but floated in sequential cascade and conventional large cell arrangements. At the Valle Central operation of El Teniente a coarse fraction of mill tailings is ground and floated, with the rejects recombined with fine tailings and subjected to cascade flotation through a sequence of concrete launders as the tailings flow towards their final deposition area. Mantos Blancos cyclone the rougher tailings and blend the underflow with scavenger concentrate from elsewhere in the principal circuit prior to flotation in Wemco Cells. Kemess in BC, Canada operates a 160 m3 Outokumpu cell to reduce the tailings sulfur content (Rasmussen, et.al, 2004)."

Jan 1, 2005

By Christoph Mueller

Broad band mine communication traditionally is characterized mainly by individual solutions, which have in common their long development phases and their high cost for development, operation and service. The use of Ethernet and the TCP/IP family of standardized protocols provide an uniquely price efficient combination of high bandwidth open networking, universal use and accessibility of price efficient development tools, especially because it forms the technical infrastructure for the worldwide Internet. TCP/IP and Ethernet assures reliable networking however it is not able to guarantee the latency timing of forwarding network information. Therefore, the network design requires strict load limitation and application level traffic control especially if moving equipment has to be manually remotely controlled via the network. The paper discusses the technologies the application of Ethernet and WLAN in underground mining environments.

May 1, 2006

By David Meadows, John Starkey

"As part of the ongoing project development for the Tenke Fungurume Copper-Cobalt Project in the Democratic Republic of Congo, Phelps Dodge Corporation has examined methodologies for determining the size of grinding mills to support a 7000 mtpd operation. Six samples were tested by Hazen Research, Inc. (HRI) to obtain the JK parameters using the JK Drop Weight Test, standard Bond crushing, and rod mill work indices, abrasion indices and by Dawson for Bond Ball Mill Work Index tests using crushed feed, and Standard Autogenous Grinding Design (SAGDesign) Tests, patented by Outokumpu. (See reference 8 below).The comparison of these results gives context to how the various measurements relate to each other and how they can be used to obtain an accurate design for the grinding mills required for the Tenke Project. This is the first published direct comparison between JK Drop Weight, standard bond work indices, and SAGDesign test results. The SAGDesign test includes a SAG test followed by a Bond BM Wi test done on SAG ground material.INTRODUCTIONAfter the presentation of the paper “SAGDesign Testing – What It Is and Why It Works” at the recently concluded SAG 2006 Conference in Vancouver, a question was asked about how SAGDesign ore hardness measurements compared with other comminution tests, specifically the JK Drop Weight Test and the parameters that are derived from such testing. At that time it was noted that a paper was being prepared for the CMP Conference in January to show how various ore hardness measurements compare with each other when done on the same samples.This paper will therefore present the first such comparison using test results from the Phelps Dodge Tenke Fungurume Project where six composite samples were examined by the tests noted below. A seventh sample was tested at Dawson but not at other labs. The tests were done at four different laboratories listed below and included the tests shown."

Jan 1, 2007

By A. Akerman, C. P. O’Connor, N. Vayenas

"Stereolithography is a well-known rapid prototyping technique in the manufacturing sector. Essentially, it is a three-dimensional printing process that produces plastic prototype parts from standard CAD files. At present, Canadian mining companies are not fully aware of the potential of rapid prototyping techniques (RPTs) for their production and mine design systems. Mining engineers and geologists attempt to visualize and understand the characteristics and layouts of orebodies on computer models, and in cases where it is decided to develop physical models, the process is time-consuming, based on simplified constructions. RPTs, such as stereolithography, can facilitate engineers and geologists to quickly, and with satisfactory accuracy, visualize sections of orebodies and evaluate alternative ore extraction techniques using 3D solid models.The research discussed in this paper is carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in collaboration with Inco Limited and the Integrated Manufacturing Technologies Institute (IMTI) of the National Research Council of Canada. The main objective with this research is to evaluate the applicability of state-of-the-art RPTs to underground hard rock mining systems. RPTs can play a significant role in accelerating the design and development process of mining systems."

Jan 1, 2006

By E. Lampard

Mines must manage variability from within their operations as well as those imposed upon them by external forces. This paper provides a framework to manage both internal and external variability through the review and adjustment of the mine plan where applicable to minimize lost production and maintain operational safety. KEYWORDS Mine plan, mine schedule, variability, safety, lost production, float days, update, adjustment, operations, Maintenance

May 1, 2011

By Christoph Müller

Information exchange for mine process optimization is essential. Today, modern mining equipment uses the IREDES standard to exchange production plans and reports for easy management and storage. To gain further benefits from process optimization, a mine wide access to real-time information is needed as e.g.: The current status of a machine, operational details etc. Presently, real-time data exchange systems are developed by machine producers. Each machine producer uses its own way of gathering, managing, and storing production data. These proprietary mining processes increase the complexity of cross platform data exchange and management for mines which involves machines produced by different vendors. Casting and unifying the data requires much effort. For this purpose, ?IREDES On-line? currently is being introduced. The standard defines an open, web based method for the exchange of volatile real time machine information. Two different principles are used: Web Services for cross platform information exchange within the IT world and the optional OPC UA for use with automation and process control systems. With such a standard information from machines of different vendors may be managed by using one common platform without spending the effort for dedicated interface development. Additionally, information management and storage will become straight forward since all the data are of the same format. The IREDES On-line standard utilizes the latest IT technologies as well as the knowledge and experiences gained from the previous IREDES standard. The paper explains the benefits, the use, as well as the technical design of the standard and gives application examples from the practice.

Oct 1, 2009

By Stephen L. Chryssoulis, Daniela Venter, Stamen Dimov

"Comparative surface analysis of floated and rejected free gold grains from a number of full scale benefication plants and from pilot plant testwork, has shown silver (the most common impurity in gold) and sulphur invariably in greater concentration on floated gold grains, implying that they assisted gold flotation (gold activators). Collector loading measurements on individual gold grains from concentrates of staged rougher flotation tests on a cyclone U/F product of a pyritic gold ore, revealed first progressively lower concentrations of the collector monomer on gold from each follow-up concentrate and secondly a direct proportionality between the surface concentration of silver and the collector monomer. These two observations leave no doubt that silver activates gold and that collector monomers play a significant, previously not fully recognized role in gold flotation.INTRODUCTIONGold to some degree is naturally floatable in industrial systems, which means that it can be recovered without collector addition (Marsden and House, 1992). This is due to the adsorption of hydrocarbons and deposition of sulphur, which are dependent on the metallic properties of gold, particularly its high electrical conductivity, which allows surface electrochemical reactions to occur catalytically and selectively. Cyclic voltammetry has shown that gold can be rendered hydrophobic by deposition of a surface layer of sulphur (Sº) from S2- and HS- solutions (Walker et al., 1984). Twenty monolayers of sulphur were required to produce a hydrophobic gold surface.However, no sulphide flotation plant relies solely on the natural floatability of gold for its recovery. Gold hydrophobicity is enhanced by the addition of flotation collectors such as xanthates (X), dithiophosphates (DTP), dithiophosphinates (DTPI), mercaptobenzothiolates (MBC) etc., as used in sulphide mineral flotation (Dekok, 1973: Adams et al., 1986). The mechanism invoked in enhancing the hydrophobicity of pure gold with the aforementioned four groups of collectors is similar to that of pyrite, whereby collector anions are oxidized at the gold surface to form dimers (Groot, 1987; Marsden and House, 1992; Basilio et al., 1992) As an example, xanthate ions are oxidized at the gold surface to form the neutral dimer dixanthogen (X2):"

Jan 1, 2003

By Mohammad Noaparast, Babak Fotoohi

"Due to certain advantages in (semi-)Autogenous-Ball mill circuits in most of the high-throughput ore grinding units of mineral processing plants, much attention is paid to optimize the mill performance. Despite the maturity of the grinding mill mechanical design, there had been made less attention to the efficiency of the grinding media in the past. In this research, the possibility of establishing a relationship between liner/lifter wear rate and variations in the composition of the iron ore (from Chadormalu mine) is investigated.Measurements and determination of liner/lifter wear rates and patterns concluded in recognition of critical liner segments exposed to much abrasion during the ore grinding. After metallurgical analysis of liner materials and correlation of wear rate with the ore composition, the homogeneity in the metallurgical microstructure of the alloyed steel (such as the uniform distribution and amounts of the constituent phases) was determined as the most influential factor in the response of the liner/lifter to the variations in the ore composition. Magnetite with greater abrasion index than hematite, in finer particles, is responsible for additional abrasion of liners; hematite with greater work index exists in the mill with larger particle sizes, thus it could produce wear on liner parts with less tolerance to impact as is the situation for martensitic steels.INTRODUCTIONThe mineralization in Chadormalu plutonic iron ore deposit is consisted of mostly magnetite, hematite, martite, apatite, quartz and carbonates. The average composition of the ore is presented in Table 1. In the processing circuit, the gyratory crushed ore reduced to 30 cm would finally be the feed to three similar 32’ semi-autogenous mills in parallel processing lines. The pulp in the mill would have the characteristics mentioned in Table 2. The quality of the mill output has its direct effect on the downstream processes either physically or chemically (e.g. in cycloning or flotation respectively). In order to take advantage of optimum performance for these circuits, a close control of the ore grinding conditions is necessary; because any shortages in throughput, liner/lifter damage or changes in ore composition could bring the unexpected casualties. In this work, it has been attempted to find (possibly) a reasonable relationship between variations in ore characteristics together with liner quality and the amount of wear rate in different liner/lifter segments of a semi-autigenous mill. Liner/lifter segments are supplied by three different domestic steel making companies. The alloy structure of the liners/lifters is made up of pearlitic chromoly steel."

Jan 1, 2005

By Lewis Martin

Whereas many researchers and mine engineers have conducted tests using different types of grout, grout ratios, and physical modifications of the cable to determine cable bolt load characteristics, few studies have been conducted on cables fitted with internal instruments. Those studies that have been done have concentrated on cable behavior averaged over significant cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed . This paper documents test results on these modified cable bolts. Three tests were conducted at SRL on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over significant cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable and thereby allow interpolation of maximum possible loads on a cable.

May 1, 2002

By Andrea M. Ouchi

A major focus of ground control research presently being conducted by the Geomechanics Group in the University of British Columbia Mining Engineering Department is to incorporate weak rock masses (RMR76 less than 50) into existing empirical design relationships. An emphasis is being placed upon the updated span design curve/critical span graph originally developed at UBC. The original database has been augmented by mapping of one mine in Montana and of several mines within the Carlin and Getchell Trends of Nevada. In addition, a neural network analysis has been performed and modifications of the span design curves at the lower RMR76 range have been made. The common factor in all the above mentioned mines is a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be dealt with to safely extract the mineral bearing rock. This work attempts to provide rock mechanic tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

May 1, 2004

By F. D. Ford, Z. Dai

"Vale’s Ontario Operations re-introduced Cu/Ni separation at Clarabelle Mill in 2006. The mill processes ores from a number of mines in the Sudbury basin. A saleable Cu concentrate is produced at 30-60% Cu recovery from mill feed, which has to meet the quality specification. In particular, Ni content in Cu concentrate must be less than 0.6%, otherwise, penalties will apply and diminish the value of Cu concentrate, in addition to the lost Ni value. Generally, a Ni grade of less than 0.4% is obtained in Cu concentrate. More recently, while processing Cu-rich ore, Cu concentrate contained more than 0.6% Ni which is abnormally high. Detailed mineralogical investigation shows that Cu-rich ore contains more millerite in comparison to typical Sudbury Ni sulphide ore. Millerite is found to be more floatable than pentlandite and is much more difficult to depress using high-lime aeration conditioning, which is the standard practice in Cu/Ni separation to float chalcopyrite while depressing pentlandite. The current operation uses sodium cyanide at 20 g/t to depress pentlandite and pyrrhotite. However, it is found that a high dosage is required to depress millerite. It is also shown that starch and dextrin are promising in millerite depression.INTRODUCTIONPrior to bulk smelting in 1991, Cu/Ni separation was carried out at Vale’s Copper Cliff Mill, Ontario Operation. The typical Cu concentrate grade was around 30% Cu and 1% Ni. This is very high in comparison to today’s value of 0.4% Ni and would not be acceptable for external processing. However, the Cu concentrate was processed internally at the Copper Cliff smelter/refinery, so the Ni contained in Cu concentrate was not lost and no actual penalties applied. During the SO2 abatement initiative, bulk smelting was chosen because of the perceived simplicity and consequently, Cu/Ni separation was eliminated (Agar, 1991) and the Copper Cliff mill was subsequently demolished. In 2005 and after more than one decade of bulk smelting, business changes required the removal of some Cu concentrate from Clarabelle Mill bulk concentrate to provide smelter capacity for Voisey’s Bay concentrate in the Copper Cliff smelter. In essence, this strategy calls for Cu removal at Clarabelle Mill (Lawson, 2006). In this case, Cu concentrate is sold externally and it must meet the quality requirement of less than 0.6% Ni."

Jan 1, 2011

By Peter A. Eshun

This paper studies two methods that account for risks associated with gold mining projects such as mineral risks and country risks. The first method is sensitivity analysis, which investigates the effects of a change in any economic parameter such as operating cost, capital investment, gold price or taxes on the viability of the project. The second method is Monte Carlo Simulation technique, which takes into consideration the simultaneous random variation of the economic parameters on the project's viability. An automated simulation cash flow model has been developed as part of this paper. Sensitivity analysis and the simulation model have been used to investigate the economic viability of the Dokrupe Gold Project (DGP) serving as a test case. It is concluded that, the Monte Carlo Simulation technique gives a more realistic judgement of the economic viability of gold mining projects.

May 1, 2004

By James A. Finch, Jason S. Doucet, Cesar O. Gomez

"Exercising control over the physical environment of flotation as a step towards process optimization is the driving force for characterizing gas dispersion in flotation cells, a subject of considerable research and still not fully understood. From an operational standpoint, however, there are just a few variables that can be manipulated to manage gas dispersion on a cell-to-cell basis, the most important being gas rate (superficial gas velocity Jg). Measurements in eight plants demonstrate there is often no strategy for distribution of gas to cells in a bank, i.e., there is no particular Jg profile. Two exercises where Jg profiles were set allowed metallurgical performance to be manipulated and an optimum Jg profile to be selected. To facilitate setting Jg profiles, a multi-unit device based on McGill Jg sensor technology is introduced. Possible directions for gas dispersion management are discussed.INTRODUCTIONThe earliest patents regarding the flotation process ignored the importance of air and in certain cases, steps were taken to eliminate bubbles from the system (Nelson and Smit, 2005). Rickard (1916) described a keen metallurgist who observed better than expected performance and hypothesized that entrained air was enhancing the process. Within a few years of this observation, the basic concept of modern froth flotation was developed whereby air is dispersed into slurry to induce bubble particle contact.As research into flotation advanced, the link between performance and the flow-rate of air entering the cell was established. In the first volume of the International Journal of Mineral Processing, Harris (1974) described the importance of airflow-rate and derived parameters such as the superficial gas velocity (then called the superficial airflow velocity) as being important parameters for cell design and scale-up. Mehrotra and Kapur (1974) presented research suggesting that the rate of flotation was strongly correlated to the aeration rate. McKee et al. (1976) continued to demonstrate the importance of airflow-rate linking it to the entrainment rate of hydrophilic gangue material."

Jan 1, 2006

By F. Lindroos

A cornerstone in the LKAB Green Pellet concept is to produce pellets with a small footprint in terms of energy con-sumption, CO2 emission and emission of other elements harmful to the environment, like dust, sulphur dioxides, nitrogen oxides, chloride and fluorine. The concept also encompasses our determination to make pellet products that contribute to low environmental impact and low energy consumption in our customer?s processes. The presentation will focus on the pelletizing process. It will describe both how we have attempted to decrease the generation of unwanted components in the process gas, and how we have tested or evaluated equipment for external gas cleaning. We will discuss and give examples from recent and on-going efforts and outline some of the future challenges we see, to meet our own environmental standards and also the tough demands imposed by EU and national legislation, while striving to boost production.

May 1, 2011

By Sylvain Létourneau

Help organizations maximize the benefits of the data that they collect ? perform scientific research in: machine learning, data mining, statistics, artificial intelligence, soft computing, information retrieval, information systems, and natural language processing ? preferred application areas: Equipment Health Management, Bioinformatics, Health, Web Mining ? today?s talk limited to Equipment Health Management While the aircraft is still in the air, IDS: ? clusters relevant WRN, FLR, and snag (pilot) messages ? identifies probable causes based on TSM and provide links to corresponding TSM pages ? assesses MEL conditions (GO, NOGO, GOIF, ?) ? displays relevant maintenance history, suggests fixes based on similar cases ? Commercialization with MxI Technologies Ltd and Air Canada in 2000

May 1, 2008

By Jessica Egan, Daniel Hodouin, Claude Bazin

"The recovery of gold by leaching is influenced by the size of the gold carrier particles and the chemical environment. Using the relationships between the leaching rate, infinite recovery and particle size for a given set of chemical conditions, it is possible to simulate gold recovery for various feed size distributions. However the use of these particle size relationships is only valid if the leaching of gold from a given size class is independent of the production history of this size class. For instance, to use these relationships it is necessary to verify that gold recovery from the leaching of the 200-270 mesh size class remains the same if the size fraction is taken from a coarse or finely ground ore sample. Several laboratory tests were carried out to answer that question. Results of the tests show that within the large error margin associated to gold content measurements, the history of the production of a size class does not affect the gold leaching from that size class. Emphasis of the discussion is put on the difficulty associated with the processing of data containing significant measurement errors as it is the case for gold assays of leaching tests.INTRODUCTIONMore than 75% of the gold produced in the world is extracted by cyanide leaching of gold ores. The ore is ground to expose the gold carriers and the ground material is reacted in an oxygenated cyanide solution that dissolves gold, leaving solids gangue minerals that are disposed to tailings ponds or returned in underground mines as paste fill. The gold contained in the solution is recovered by either the carbon in pulp process or by cementation onto zinc powder, before being melted and casted into a brick (Marsden and House, 2006)."

Jan 1, 2009

By Yongbao Zhu

The Ag2O-mediated reactions of cycloaurated compounds with a general formula Au(L)Cl2 (L = bi-dentate C?N ligand) with thiosalicylic acid, N-acetyl cysteine or 1,2-benzenedithiol in DMF proceeds via ligand substitution of the Au?Cl bonds to afford the S-O and S?S adducts all in good yields. The reactivity of the dichloro, S-O and S-S adducts towards thiols were examined by reacting with cysteine in an aqueous medium, revealing that all of Au-Cl, Au-O and Au-N are labile for thiol displacement. The measurement of the inhibitive activities of these compounds against human cathepsins B and K showed that the dichloro and S-O adducts are effective inhibitors with IC50 values ranging from 0.1 to 2.6 -M, and that the S-S adducts are inactive.

Oct 1, 2003

By Ertugrul Alp

Alp & Associates - Who We Are ?? Canadian consulting company (1999-?) ?? Principal Consultant: Dr. Ertugrul Alp, P.Eng. ?? Over twenty-five years experience serving the chemical, mining, pulp & paper, energy, steel, and transportation industries, and government clients. ?? Ph.D. in Mechanical Engineering, University of Waterloo ?? Experience: ?? Westinghouse Canada, Atomic Power Division, Manager, Analysis and Modelling ?? Concord Environmental (later Bovar Environmental), Principal, Manager, Air Quality and Risk Assessment ?? Arthur D. Little, Associate Director, Safety & Risk Practice Leader in Canada ?? Member: NATO CCMS Pilot Project on Disaster Preparedness (1991-1993) ?? Chair: MIACC Risk Assessment Expert Committee, 1995-1999 ?? Member: MIACC Committees on Land Use Planning and Pipelines (1993-1998) ?? Member: CSA/Q850 Risk Management Standard Technical Committee ?? Member: CSA/Z1002 OHS Risk Assessment Standard Technical Committee ?? Member: CCPA/CSChE Process Safety Management Committee (1999-?) ?? Member: ISO-31000 Risk Management Standard Canadian Advisory Committee ?? Chair: CSChE Process Safety Management Committee (2005-2006) ?? Chair: CSChE Expert Committee on Risk Assessment (1999-2005) ?? CSChE 2007 Process Safety Management Award

May 1, 2008