Search Documents

By H. R. Banks

"AbstractThe rod mill introduced into the Sullivan Concentrator flow in September, 1948, replaced two sets of 74 in. by 20 in. rolls and their accompanying screens. In addition to the work formerly done by the rolls, the rod mill is producing a finer product and one which provides more suitable feed for the primary ball mills. The object of the finer discharge from the •primary mills is to make possible a feed directly from the mills to a series of flotation machines where a large portion of the galena can be withdrawn from the circuit while the galena is still coarsely granular. The interposing of classifiers between grinding and flotation means the selective grinding of the galena.The author summarizes the work of •the rod mill through the first 5,000,000 tons and shows that the wear of lifters, liners, and rods is definitely below normal for the type and size of rock being handled. The rod mill, driven through a fluid coupling, has been subject to a range of speeds from 13.5 to 19. A pinion in the speed reducer was changed to allow the extending of the normal speed range of the fluid drive of approximately 4 r.p.m.Since the critical speed inside the liners •is 23.4, the range •in per cent of criticial is 57.7 to 81.2 per cent.The capacity of the mill increases with increasing speed but the character of the product remains approximately the same except when the feed rate is too high.Consumption of steel, power, and other operating data are presented.The author introduces certain fundamental observations on the principles involved •in comminution in order to support the special design and operation of the rod mill."

Jan 1, 1952

By C. -K. Fang

"Aging effect on the wear resistance of alumina particulate-reinforced 6061 aluminum matrix composites with a block-on-ring wear tester has been investigated. Specimens with various Al2O3 volume fractions of 0%, 10% and 20% were employed in this work. Experimental results indicated that over-aged monolithic 6061 Al had the best wear resistance, as compared with under-aged and peak-aged conditions. For the composite containing 10% Al2O3, over-aging and peak-aging resulted in similar wear resistance, which was higher than that for underaging conditions. For the composite containing a high volume fraction (20%) of Al2O3, the wear resistance reduced with the increase in aging time. Although longer aging time was favourable to the wear resistance of monolithic 6061 Al, it was detrimental to that for the Al2O3/6061 Al composite with high volume fraction of particles. IntroductionMetal-matrix composites (MMCs) have received attention in many engineering applications because of the demands for high specific strength (strength-to-weight ratio) and specific stiffness, good high temperature capabilities and wear resistance. The manufacturing processes of fiber-, whisker-, and particulate-reinforced MMCs have been well developed (Hosking et al., 1982). Because of the reduction in fabrication cost, the applications of MMCs have been widely extended to light weight-bearing sleeves, calipers, automobile parts (brake rotors, drive shafts, connecting rods, piston rings, and cylinder liners), sporting goods, aerospace components, tanks (wheels, speed brakes, and track shoes) and other industrial applications. Among the three types of metal matrix composites, particulate-reinforced MMCs are promising because of their homogeneous and isotropic material properties and low cost. Additionally, they can be formed using conventional metal processing techniques."

Jan 1, 2003

By Maureen E. Lipkewich

Education builds long term awareness, acceptance and support for responsible mineral resource development. The MABC Education Program is an award winning education partnership with British Columbia classroom teachers that has helped over 5400 teachers with resources and other learning opportunities. Each year, thousands of students begin, and continue, to learn about our modern mineral industry as a result of this teacher-written program. The CIM network has an integral role in the future of mineral education in today?s classrooms in Canada and programs of this caliber are vital to our future. The industry needs help in raising awareness of the benefits of modern mining and teachers need help in acquiring that information.

May 1, 2002

By Ryan Montpellier, Paul Hebert

"Prospecting the Future: Meeting Human Resources Challenges in Canada's Minerals and Metals Sector is a comprehensive sector study of the short- and long-term human resource issues and challenges facing the minerals and metals industry. The study's in-depth assessment of current and emerging human resource needs and gaps served as a foundation for the recommendations designed to maintain the strength of the minerals and metals sector well into the future. The study provides insight and identifies strategies relating to each of the following areas:•,An aging workforce•,Significant retirements on the horizon•,Human resources demand growth•,Supply challenge - education and training programs•,Under-representation of non-traditional groups•,Supply advantage - attractive features of mining•,Supply and demand gap"

Jan 1, 2007

By Andrew R. Marchbank

The application of biologically assisted methods for metal extraction in the mining industry has a long history, but development of modern techniques has been relatively slow. There is, however, a resurgence of interest in the industry with the recent development of methods to successfully treat base metals concentrates. Two major pilot plant programs for treatment of chalcopyrite concentrates have been initiated in the past year and results from one are beginning to be released. This paper provides an overview of methods that have been applied in the past; from the earliest deliberate applications of the technology, through the copper and uranium heap and dump leach applications, the more highly engineered agitated tank leach gold applications and the developments currently taking place in the industry.

May 1, 2002

By A. R. Miller, G. Desrivières, M. C. Bétournay, D. L. Barnes, P. Laliberté

"Over the last four years, an international initiative, championed by Vehicle Projects LLC, the Fuelcell Propulsion Institute and Natural Resources Canada, has been active in carrying out research projects to prove out the concept of applying fuel cell technology to underground mining vehicles. These have been carried out by a consortium consisting of mining companies, equipment manufacturers, technology developers, national laboratories and consultants, with the participation of Canadian and U.S. mine regulatory agencies.This clean technology, which produces only water and electricity, would allow several advantages to be obtained, in the health area (by eliminating diesel emissions and reducing noise generation), in lowering production costs (such as reducing ventilation required) and lowering greenhouse gas emissions.This paper outlines the results obtained in several key areas, such as, the operation of fuel cells in underground conditions, risk issues related to underground and surface operation of hydrogen vehicles and hydrogen production and delivery systems, and the design and mining performance of the world’s first hydrogen mining vehicle, a mine production locomotive. The work to date on the fuel cell loader, designing the power plant and power transmission systems, operational requirements, and operating cost reductions is also presented."

Jan 1, 2003

By Margarete Kalin

"Difficulties arise in implementing environmental technologies in the mining sector because important fundamental processes, which lead to the environmental degradation, are ignored. Weathering rates, the role of bacteria in the process and the incomplete application of the matching principle of accounting at the time the mining disturbance take place. Mining is a multi-stakeholder activity and the environmental problems have multivariate dimensions also effecting process.The limiting factors in the contaminant generation process are the transport of oxygen by advection, convection or diffusion in air or water and the associated microbial activity. Weathering products are transported from the mineral surface by atmospheric precipitation to surface and groundwater. This contamination takes place at different rates, requiring a long time to evaluate technological choices.Restoration efforts have to focus on slow reaction rates in the contaminant generating processes. Technology, which does not address the reaction rates and is selected based on inappropriate time scales, will not provide long-term solutions. Natural approaches to reduce acid generation, based on Ecological Engineering principles have required decades of research and field testing, but now show promise in addressing the cause of AMD and ameliorating its effects."

Jan 1, 2005

By R. Hamilton

"Louvicourt mine began operation in 1994. It is located in northwestern Quebec, 20 km east of Val d’Or. The mine is owned by Aur Resources (30%), which operates the mine, Teck/Cominco (25%) and Novicourt (45%). By the end of 2002 there were approximately 280 employees working on the site, including contractors. Production averages 4300 tons per day, working a massive sulphide body located between 415 m and 920 m underground.Maintenance expenses represent 27% to 29% of the operating costs, and the maintenance personnel represents 34% of the total workforce (including electrical, mechanical and concentrator maintenance staff). Considering these figures, in addition to capital costs and indirect costs, such as energy (electricity, fuel, gas, etc.), it is worthwhile to pay attention to how things are done in order to protect such investment. Every task performed to help understand the impact of Louvicourt’s practices must to be seen as an investment in the reliability of its operation."

Jan 1, 2003

By H. F. Naldrett

"AbstractAt the end of May, 1950, Imperial Oil, Limited, had completed a total of 192 D-3 wells in the Leduc-Woodbend field, 62 of which lost circulation in the D-3 zone for periods ranging from two hours to fifty days. The majority of the remaining wells •lost some mud without actual loss of returns. In addition, independent operators completed 69 D-3 wells, of which 9 lost circulation. Included among the latter is the now well known Atlantic No. 3 well, which blew wild out of control for seven months. The well was finally brought under control through two directionally drilled wells, but not before the derrick fell and the well caught fire. Practically all known filler materials have been used in attempt3 to prevent or regain loss of circulation, but none has been successful, except in minor cases. Ordinary sawdust has come to be the most commonly used filler material and is added to the mud before the D-3 zone is contacted. In cases of serious loss of circulation, the on1y successful method of getting returns has been the use of a series of small cement plugs.IntroductionThe Leduc field is twenty miles southwest of Edmonton, Alberta. Geologically, it is on the east limb of the Alberta syncline, in the homoclinal belt. The main productive zones are in the Upper Devonian formation and are known locally as the D-2 zone and D-3 zone, respectively (see Figure 1).The D-3 zone is a dolomitized reef with fair average porosity and permeability, and shows considerable evidence of vertical fracturing. Porosity is mainly due to moderately uniform development of vugs which are interconnected by small crevices. However, the formation is known to be, locally, extremely vuggy and in places cavernous. These latter conditions create very serious drilling problems due to the hazard of loss of circulation, particularly in the gas cap, which has a maximum thickness of 200 feet. The D-3 zone is contacted at an average depth of 5,300 feet."

Jan 1, 1950

By T. Nyabeze

This paper presents the experiences and views of women involved in the mining industry as determined from a questionnaire that was circulated across the Canadian mining industry. Globally, there have been significant studies done to understand the historic and global variety of women?s participation in this industry1. The reason for focusing on women?s experiences here in Canada is because women?s percentage representation at 14.4% in the mineral industry workforce falls below the overall labour force average of 47.4%2. Notably, a recent article in the Globe and Mail newspaper points out that adequate representation of women in leading of organizations is more of a matter of competitiveness and innovation rather than purely a ?women?s issue?3. This paper will provide some insight into the reasons why women join and stay in the mining industry and shed some light into the reasons for the overall low representation in this sector. The authors believe, as stated in a study from the London Business School, that a gender-balanced workforce is one way of providing the best results in areas that drive innovation4. Women represent a key stakeholder group that can help enhance the mining industry?s sustainability through innovation. The women who responded to the questionnaire represent many different areas within the mining industry, including a broad range of roles in industry, government, academia and in the supplies and services sector. The paper is intended to raise awareness about issues that women encounter that contribute or detract from career satisfaction in the mining industry. The survey provides an overall understanding of why women pursue or work in mining, and why women either remain or choose to leave it. The advantages and disadvantages experienced by women are highlighted, along with a summary of the possible initiatives that could be undertaken by employers as opportunities to improve the attraction of the mining industry for career minded women. As well, the survey provides a summary of the top ten features that are already in place at various organizations and community groups that have been identified as key for supporting and encouraging women to join and remain in the industry. Not surprisingly, the survey identifies that one of the key ingredients for retention of women in mining is the provision of mentors and sponsors. Another key aspect for retention is the provision of progressive employment policies that address the need for a degree of flexibility in work hours and a culture of balance between work and personal life demands. The survey and results are portrayed only from a female perspective since it is largely women?s perceptions that will inevitably be transmitted to others who plan on entering the field.

Oct 1, 2010

By G. Auld

"A simple method is presented whereby the additional quantity and static pressure necessary to compensate for ventilation duct leakage may be estimated using the circular reference functions of modern spreadsheets. Favourable comparisons have been made to the National Coal Board (United Kingdom) design charts and to a case study analysis. IntroductionIn mining, most ducted systems are applied to the development of access tunnels, and most of these systems leak to some extent. When the ventilation duct fails to deliver the required quantity of air to the work place, there is a significant contribution to the development costs, either directly or indirectly.Directly — More air and more pressure are required to compensate for the leakage, more capital development (ventilation shafts, parallel drives) are required because ventilation systems cannot push the fresh air far enough, and longer re-entry times to ensure toxic blast fumes to be diluted.Indirectly — There is a reduction in productivity because of the inclement atmospheric conditions, and/or closure of development ends because of unacceptable atmospheric conditions at the working place. This has been exacerbated over the last few decades because of the increased use of diesel equipment of ever increasing power, and the more stringent Occupational Health and Safety requirements demanding more air flow per kilowatt of diesel power.The leakage from a duct must, therefore, be reliably estimated in order to assess the effectiveness and construction of the system; assess the effectiveness of the maintenance or repair of the duct; appreciate the cost of the leakage, and therefore apply effective maintenance and installation procedures; and engineer safer, healthier and more cost-effective ventilation systems."

Jan 1, 2002

By D. Prince, G. Nollet

"Since 1994, Aur Ressources has operated Louvicourt mine, a zinc and copper mine close to Val d’Or, at a rate of 4300 t/d. Ever since the start-up of the plant, management has encouraged innovative approaches in reliability. The first of three papers will discuss the vibration monitoring program in place. The program will be described and two examples will be given: detection of a rolling bearing defect on a pinion driving the ball mill and identification of wear on the bearings of the flotation cells. Figures on the return on investment and the costs of a monitoring program will also be given.The second article will discuss the lubrication aspect. Since the establishment of a good monitoring and oil analyses, Louvicourt mine decreased its oil consumption by more than 38 000 L/yr. In addition, the company set up an oil regeneration system that restores the original properties of oil.The third article will cover the management aspect. Work organization as well as the management philosophy enabling the employes to push predictive technology to higher levels will be examined in detail. The key elements which made it possible for Louvicourt mine to position itself among world-class companies in the organization of maintenance will be discussed."

Jan 1, 2002

By Euler De Souza

The authors conducted a study of backfill practices in underground mines across Canada to assess the current state of backfill usage and to overview potential hazards associated with backfill practice, from preparation to transportation to placement. The primary aim of this study was to cover each component of a typical mine backfill system, and to identify potential incidents leading to the disruption of backfilling operations and any associated corrective actions. This paper, Part I of the study, deals with surface operations consisting of backfill material supply and backfill plant preparation. Part II of the study, which deals with underground operations consisting of backfill transportation and backfill placement, is also presented in these proceedings. A review of safety measures associated with current backfill operations and recommendations for procedures of best practice that should be implemented to reduce fill-related hazards in all mine backfill workplace environments are presented. In general it has been found that system failures normally lead only to minor losses to the operations.

May 1, 2009

By C. Vanvoren

"Since 1975, the Aluminium Pechiney Research Centre at Saint-Jean-de-Maurienne (LRF) has been concentrating its efforts on designing, testing and perfecting the Aluminium Pechiney point-fed prebaked reduction cell.In 1979, the AP18 cell (180 kA) was industrially launched with the construction and start-up of the F line in Saint-Jean. The following generation, the AP30 (300 kA), with prototypes started in 1981, was launched in 1986 on the Saint-Jean G line. Along with cell design, efficient process control systems were developed to pilot alumina feeding and bath composition. Together, these pots are currently producing 4.6 Mt of aluminum, i.e., 18% of the world’s overall yearly production.In 1989, the research centre faced a new challenge: to push the limits for the size of a reduction cell to further improve the profitability of Greenfield projects. This new generation development was also the opportunity for a significant redesign of the Aluminium Pechiney electrolysis information system.With a track record of ten years of semiindustrial operation with three prototypes, the AP50 technology is now ready for industrial implementation and enables a significant breakthrough to be made in terms of return on investment of a Greenfield smelter."

Jan 1, 2002

By Natasha A. Essar

Nevsun Resources Ltd. Bisha Mine Project is a gold and base metal development project in the Gash Barka region of west-central Eritrea. The project has the potential to be one of the largest industrial developments in the country, and Eritreans have no experience in modern mining. Nevsun recognized early that the success of the Bisha Project would require meaningful consultation and engagement with all levels of Eritrean society. Meaningful engagement required not only full disclosure, but also capacity building from government officials at all levels to other stakeholders who live in the nearby communities. This paper describes the approach used to develop capacity and to help introduce a modern mining culture in a country without previous experience in mining.

May 1, 2007

By M. Pekguleryuz, S. A. Argyropoulos

"The recovery of additions in light metals is an important parameter influencing consistency of the finished product, which ultimately means cost. Recovery is a function of many parameters such as assimilation speed, addition density, addition practice, liquid metal processing conditions, etc. In liquid metal processing operations, it is desirable to have the maximum possible recovery at the shortest possible time.In this paper a new index will be presented, namely, the rate of recovery (RR). This index quantifies the addition recovery and introduces the time dimension in the recovery increase. As such, the RR equips the liquid metal practitioner with an accurate picture of addition assimilation in liquid metals. Results will be presented on how this index is applied to a variety of additions in liquid aluminum. IntroductionThe data on addition assimilation kinetics offer a valuable parameter describing how fast a given addition enters the metal bath. These data may be expressed as gr m-2 s-1 of additive for a set of experimental conditions which might include bath temperature and degree of bath agitation among others. However, the liquid metal processing practitioner is more interested in the recovery of additions. In other words, the point of interest is the percentage of the used addition entering the metal bath. Ideally, the addition recovery can reach the 100% level. However, in practice, the addition recovery never or rarely reaches that level. Many factors can contribute to this. Some of these factors can be slow assimilation kinetics, addition density, addition practice, turbulence of the melt, etc. In some cases, sloppy addition practices can contribute to low recoveries, or even worse, to erratic recoveries.In this paper a new parameter is introduced. This parameter relates the maximum addition recovery observed over the time needed to achieve this maximum recovery."

Jan 1, 2002

By P. Desclaux, A. Gosselin

"In 1999, PFC measurements were carried out at Alcan smelters as part of a large measurement campaign led by the Canadian Aluminium Association. Side worked prebake (SWPB) and horizontal stud Söderberg (HSS) plants in Arvida were the selected sites. CF4 and C2F6 emissions were measured continuously in the exhaust duct and at the roof vents for a week. In parallel, voltages from four designated cells were recorded at a high scan rate. Results were analyzed and correlations between voltage, anode effect duration and PFC emissions were tested. Some fundamental anode effect mechanisms were proposed and validated with the observations. IntroductionFollowing the international agreement reached within the scope of the Kyoto protocol, voluntary partnerships have been established in many countries especially for the aluminum industry. It is well known that the PFCs that are periodically emitted during aluminum production are the major source of fluorocarbon emissions. The latter are part of the greenhouse gases. In the fall of 1999, Alcan announced that it will adopt, promote and regularly renew a long-term greenhouse gas management commitment at all of its facilities within the framework of the so-called TARGET program that was implemented during 2001. The program is intended to produce on-going reductions, which will be reported publicly on an annual basis.Improvements in the understanding of the mechanisms leading to PFC emissions will contribute to targeting the most appropriate reduction actions. PFC measurement campaigns have been driven toward this end. The first measurement campaign was conducted in 1993 in order to get a picture of the emissions and a base line. The last measurement campaign was conducted in 1999 and its main objective was to compare current emissions with those measured in 1993 and to confirm the accuracy of the predictive equations for the calculation of PFC emissions. This campaign has been conducted by the Canadian Aluminium Association and measurements were made in plants using different technologies. Results of this campaign have already been reported by Bouchard et al. (2001)."

Jan 1, 2002

By Linda Dufour

"Autoclaves have been in commercial use in the mining industry since the early 1950's the initial applications included tin, uranium, cobalt, nickel and copper extraction under both acidic and alkaline conditions. These circuits varied in batch or continuous operation. The geometry has been spherical, vertical, and horizontal type with up to six agitators, with throughput as high as 1000 stpd.Presently autoclaves are a good process selection for many refractory sulphide gold bearing ores. The first application of pressure oxidation in the gold industry was at the Homestake Mcglaughlin's Mine which was commissioned in 1985. This was an acidic pressure oxidation process treating 3000 stpd in three four compartment horizontal autoclaves 14' diameter and 53' long. Since the initiation of autoclaves for the treatment of gold bearing sulphides, there are presently 16 gold autoclaves operating worldwide varying in size up to 18'4"" inside diameter. There are seven autoclaves for the treatment of refractory sulphide gold bearing ores to be commissioned in 1997 and 1998.Autoclave technology has progressed extensively since the mid-eighties. Operational experience has made rapid progress and the result is much smoother and safer autoclave operation. There have been many advances in autoclave technology design. For example, the use of exotic materials for corrosion resistance to reduce down time for maintenance. The instrumentation involved in autoclave operation is very sophisticated which allows for many safety features. The advanced design has allowed for greater availability and as a result operating costs and maintenance costs have decreased. These technological advancements have made autoclave technology more safe and this has resulted in a greater acceptance of this type of operation. Many of the gold autoclave facilities operate up to 9 months continuously without shutdowns. The advancement of autoclave technology has inspired many new applications.Because of the outstanding operation of autoclaves in the gold industry, many other applications for autoclave technology are being considered. The following is a list of autoclave applications:"

Jan 1, 1997

By Horst Konig

This paper illustrates that, with the application of new processes, smaller steel plants using local raw materials can be economical and advisable. It also introduces the problems connected with the direct reduction processes, which use non-coking coal or gas as reducing agents, and which are employed in connection with conventional reduction to produce excellent results. Electric smelting is also discussed, and some practical examples of operating plants are given.

Jan 1, 1970

By Glenn Kosick, Roger Amelunxen, Glenn Dobby

"The variability in flotation response within an orebody is often a significant problem to address during the design phase of a flotation circuit. In addition, for existing operating plants, the reasons for such a variability need to be clearly understood and accounted for if plant performance is to be optimized. MinnovEX Technologies, in collaboration with major mining companies, is developing methodologies and tools to address the issue of variability in ore characteristics (such as ore hardness and flotation response). The tool is used for design and scale-up of flotation circuits from lab flotation data, and for prediction of recovery and final concentrate grades throughout the mine block model for any given circuit design.INTRODUCTIOTNH: EI SSUEB EINGA DDRESSEDThis paper describes the current development of a methodology and software tool for improved flotation plant design and enhanced prediction of froth flotation performance in an operating plant. The need for this tool is attributed to two primary factors: variability of flotation response properties throughout an orebody and related difficulties with scaleup from laboratory tests. Consider these in more detail.It is well recognized that separation performance via froth flotation will vary significantly within a single mineral deposit. This has been enhanced through the wide application of SAG milling. Throughput with SAG mills is more susceptible to ore hardness changes than is the case with crushing-rod-ball circuits; it is not uncommon to see SAG mill throughput to vary by up to 100% on a regular basis, e.g. 1000 tph to 2000 tph.The implication of this on laboratory testing for prediction of metallurgical performance is as follows: it is unlikely that either the plant grind (size distribution) feeding froth flotation or the flotation residence time will be known at the time of laboratory testing for a given block of ore. Hence, the grind used for the laboratory test is not likely to be that which actually occurs once the ore is processed, and the laboratory retention time may not represent the plant conditions."

Jan 1, 2002