Search Documents

By D. Vanin

"Conventional single heading track drifting in the hard rock mining industry has not shown any significant improvements in advance rates, despite the advent of modern track jumbos and igh speed muck handling systems .This paper presents Kiena 's experience in using a 7 ft 2 in. diameter larva Mark 6 Tunnel-Boring Machine (TBM) for driving 6000ft of drift.IntroductionKiena Gold Mines is located about 5 miles west of the town of Val d'Or, Quebec, approximately 300 miles north of Montreal. The mine commenced production in October 1981 and has gone through various expansions of ore production with 287 916 metric tonnes in 1982 to reach 453 800 metric tonnes in 1986.Due to the majority of claims being covered by a lake, a grassroots exploration drive of remote areas of the property was required to allow diamond drilling on a yearly basis. High speed sequential excavation methods (SEM) of single heading drifting in the mining industry has not progressed much in the past 20 years despite the advent of electric-hydraulic jumbos, Haggloader and Hagglund type cars. Certain examples of record SEM drifting advances have been performed in the past but only under very specific ground and cost conditions."

Jan 1, 1987

By W. Dingley, G. R. Hoey

"Thirteen Canadian sulphide ore mines were surveyed for corrosion control. The mines visited were a small, yet representative, proportion of this segment of the Canadian mining and metallurgical industry. Information on metallic corrosion and methods used to control it in underground workings and mills was gathered (a) by discussing corrosion problems with company personnel, (b) by examining equipment and structures during under-ground and mill tours, (c) by photographing corrosion sites, and (d) by collecting and analyzing mine water samples.The corrosion survey, which is summarized in the re-port, leads to the following general conclusions. Mine environments are corrosive, particularly when the mine w1a-ter is acidic. Because of a lack of good corrosion control measures, excessive deterioration of equipment due to corrosion occurs in mines. Mill environments are also corrosive, but in some cases good preventive measures are being taken to effectively control corrosion losses.Ways to reduce corrosion losses in sulphide ore mines and mills are discussed. The main areas for more corrosion research and development are selection of materials of construction, protective coatings, cathodic protection, inhibitors, equipment design, and mining and milling practices."

Jan 1, 1971

By V. I. Lakshmanan

Recycling helps to save energy and is good for the environment. It is also important for preserving the limited natural resources. In addition, recycling creates economic benefits and frees up space at the landfill sites. Process Research Ortech Inc. (PRO) has conducted extensive testwork in the area of waste processing and recycling. A process was developed for the recovery of Zinc from galvanized steel by alkaline leaching followed by solvent extraction and electrowinning. Extensive testwork has been conducted at PRO to obtain a useful by-product from rice husk. Rice husk was combusted in a gas/solid reactor to obtain an environmentally acceptable amorphous silica ash suitable for use in high strength concrete. In another development, vanadium was recovered from fly ash by separating carbon first, followed by alkaline pressure leaching, solvent extraction and precipitation. PRO has also developed an environment friendly process for treatment of industrial wastewater for its reuse to obtain zero or minimal effluent discharge. In this paper, four case studies related to recycling of zinc scrap, controlled combustion of rice husk, processing of fly ash, and reuse of waste water will be discussed.

Jan 1, 2011

By E. L. C. Martins, M. J. Nicol, D. Majuste, A. D. Souza

The effects of organic compounds on the current efficiency (CE), morphology, crystal structure and mechanical properties of the metal deposited during the electrowinning of zinc are described. A flotation collector and lubricating oil were selected based on observations made during the industrial production of zinc from silicate ores, in Brazil. The analysis by Fourier transform infrared spectroscopy of these compounds, which may be present in minor amounts in the electrolyte solution, indicated the presence of a polar amine group in the collector, while the lubricating oil is a non-polar compound. The average CE value obtained from organic-free industrial solution was 91.15 ± 0.26 %. The CE dropped to 54.35 ± 0.73 % in the presence of 100 mg·L-1 of collector in the solution, and a negative effect was also observed in the presence of similar amounts of oil (88.84 ± 0.61 %). The characterization of the deposits by scanning electron microscopy and X-ray diffraction revealed the formation of pores in deposits obtained from solutions containing the oil, while a different growth pattern (perpendicular zinc platelets) was identified when the flotation collector was added to the industrial solution. In the presence of these contaminants in the solution, guided-bend tests revealed that the deposits have a higher resistance to deformation, but lower ductility, properties that may affect the performance of the stripping stage. As a result of this work, simple control and optimization actions were applied in the industrial plant, which resulted in important improvements in the electrowinning process.

Jan 1, 2014

The Challenges in Mining _Large expensive assets that are not being utilised as well as they should _?Silo? operations plan, schedule and execute in isolation?poor visibility across the Value Chain _Disruptions or unforeseen events have serious upstream and downstream impacts _Exacerbated by multiple information systems, mostly spreadsheets _Strategic simulation (supply and demand) is often poorly Handled

Nov 1, 2011

By A. Trusiak

"Increasing energy costs in mineral processing is making it necessary for tighter controls over various parts of the concentrating process. Continuous monitoring and control of critical process streams can be easily performed by today's many computer systems. Indeed, the list of successful applications of computers to grinding and flotation control continues to grow. The day is rapidly approaching when the use of computers within concentrators for either process control or simply metallurgical accounting will no longer be a luxury, but a necessity. The benefits from such applications far out weight the initial investment.This paper describes the current application of a process control system at Brunswick Mining in north-eastern New Brunswick. Emphasis is placed on the control of a CuPb flotation circuit, and the benefits derived-from this control.No. 12 Cu-Pb Flotation: The complex nature of the Brunswick flotation process has been described else-where. 1,2,3 Four final concentrates are eventually produced, these being a Zn concentrate assaying 53% Zn, a 30% Pb concentrate, a 20% Cu concentrate, and a bulk Pb Zn concentrate assaying 35% Zn and 17% Pb. The Cu concentate, Pb concentrate, and bulk Pb Zn concentrate are all derived from a primary CuPb concentrate assaying 26% Pb, 11% Zn and 1.8% Cu.The No. 12 CuPb circuit produces approximately two thirds of the total primary CuPb concentrate. No. 12 ore, assaying 3.5% Pb, 9% Zn, 0.25% Cu and 100 g/tne silver, is ground in two parallel grinding circuits. Each line uses a 3.2 x 4.2 meter rod mill in closed circuit with two parallel 3.2 x 3.9 meter ball mills. Ball mill and rod mill discharges are classified in two stages of cycloning. The secondary cyclone overflow, or flotation feed, is controlled at 65% passing 37 microns."

Jan 1, 1981

By M. Hitch, M. B. Lytle

Resource development conflicts arise largely due to differences in worldview between those who support and those who oppose development. This paper illustrates how societies and civilizations with different worldviews produce different levels of creative and economic energy. A questionnaire was created to build a database of responses to test whether worldview and resource development are correlated. Factor and multivariate regression analysis determined correlations for respondent groupings. Results showed a positive correlation between the respondents\u2019 worldviews and their attitudes toward resource development. Correlations became stronger as the homogeneity of the sample subgroups increased.

Jan 1, 2017

By S. Power Warren

Introduction It is generally conceded by flotation men that the condition at the surface of a particle of mineral or gangue is the most important factor controlling its behaviour in a flotation cell. Much research work has been devoted to the study of the forces that are active at the surface of the particle and of the effect of the surrounding solution upon these forces. Study of the relationship between mineral or gangue particles and gas bubbles indicates that, in the main at least, flotation is a physical phenomenon. The important factor, that of mineral-gas-bubble attachment, is unquestionably physical; however, modifications may be effected by chemical means, whereby the nature either of the surface of the particle or of the surrounding solution may be changed. For example, the coating of lead sulphide that forms on lead-carbonate ore particles when sodium sulphide is added greatly aids the flotation of the carbonate particles. Without going into the question as to why, under certain surface conditions, mineral particles will attach themselves to gas bubbles whereas under other conditions they will remain unaffected, it may be stated that there are three general conditions in a flotation pulp which control the attachment of the particle and the gas bubble.

Jan 1, 1933

By Fred V. Seibert

The Functions and the Responsibilities of the Institute The Canadian Institute of Mining and Metallurgy is unique. ln addition to the welfare of its members, it has a real interest in the welfare and promotion of one of Canada's largest and most important basic industries. It is because of this that the membership is composed of both individual and corporate members. The individual members are both technical and non-technical (Members and Associates). Both Members and Associates have the same status in the Institute and all are interested in the welfare of the mineral industry. The aims and objects of the Institute 11re twofold. The education and welfare of its individual members and the sound promotion and welfare of the mineral industry. Perhaps it might be well if we reviewed these aims and objects as stated in our Constitution: "First - To promote the arts and sciences connected with the economical production of valuable minerals and metals, by means of meetings for the reading and discu11ion of technical papers, and the subsequent distribution of such information as may be gained throo.gh the medium of publications". It cannot be denied that we have do ne a good job in this particular phase of our work. Nevertheless, there is still room for improvement. It has been suggested that we might have more discussion and, on occasions, more criticism of our papers and programmes. This can best be done if the authors will have their papers prepared in sufficient time to permit of preprints being made availa1ble before the meeting at which they are to be presented.

Jan 1, 1950

By R. F. Coulter

THE Flin Flon concentrating and metallurgical plants (Figure 1) of the Hudson Bay Mining and Smelting Co., Limited, lie adjacent to the town of Flin Flon, on the Manitoba-Saskatchewan border, 400 miles northwest of Winnipeg. Since the start of milling operations in 1930, over 50 million tons of ore from the Flin Flon mine have been treated in the concentrator. During the past few years, newly discovered orebodies have been brought into production and their ores processed at the company's main metallurgical plants. All these properties are within a 75-mile radius of Flin Flon and have aided substantially in augmenting plant metal production as well as retarding depletion of ore reserves in the Flin Flon mine. •Current satellite producers are the Schist Lake, Coronation, and Chisel Lake mines. The Schist Lake mine, located 3 ½ miles southeast of the main plant, is a copper-zinc producer. It was brought into production in 1954. The

Jan 1, 1962

By G. R. Elliott

Foreword The office of the Supervisory Mining Engineer, a branch of the l. Federal Government, is financially interested in no oil company and has no stock to sell. This office, however, is deeply interested in the proper and efficient development of Canada's natural resources. The people of Canada are interested in the petroleum development in Turner Valley for two principal reasons: As represented by the Department of the Interior, they are the largest owners of petroleum and natural-gas rights in the field; As a nation, they are vitally interested in the development of petroleum and natural gas as a national asset, and therefore, also, in all productive property, no matter who directly controls the leases. As has been stated by Mr. Charles C. Ross, Supervisory Mining Engineer, "The Department, being responsible for the administration of these public resources, necessarily requires regulations to protect them from abuse by lessees. Our portion of this responsibility is to record a complete history of all drilling operations and to see that proper drilling methods are adopted to prevent damage and wanton waste of the valuable natural resources under discussion." Not only does our position necessitate an impartial and a judicial viewpoint, but, being day by day in touch with all operations in the western provinces, we are uniquely situated to comprehend both individual and general problems.

Jan 1, 1930

By M. F. Almeida

"Due to the randomness of all factors influencing the sintering operation, a two-stepped procedure is proposed to find the best way of using stocked fines at a plant producing Fe-Mn alloys for the steelmaking industry. The approach is based on the following: (1) predict the result of the sintering operation by establishing the best multilinear regression model using some of the characteristics of the loaded material; and (2) find the best solution under a minimizing cost criteria by solving a linear optimization problem using the regression equation plus constraints on the feed and product. IntroductionSome tests carried out using 20% to 30% of sinter in the material loaded into a 60 000 KVA Tysland-Hole electric furnace producing Fe-Mn alloys for the steelmaking industry indicated: (1) a meaningful decrease in the off-gas temperature and, consequently, a better energy use due to the material higher porosity; (2) more uniform heat distribution as a consequence of the electrode reaction zone enlargement; (3) an improved furnace control resulting in a smoother operation; and (4) a decrease in gas production facilitating the off-gas treatment. For some years, this plant used only the coarse fraction of the Mn ores, thus stocking all the received and own-generated fine particles. In view of the mentioned results, a strategy for increasing the use of stocked fines was formulated, including a step where it was necessary to decide which components and respective quantities should be used in the blends to be sintered (Almeida, 1984).It is well known that several factors affect productivity and energy consumption in sinter production, also influencing the product quality. Raw materials characteristics, namely chemical and size composition, affect permeability to gases and may or may not allow a deeper bed. In general, finer ores decrease permeability, increasing electricity consumption by fans, but due to their higher specific surface area, react more completely with other components in the mixture. For coke granulometry, a compromise must be obtained in order not to burn it too quickly nor to widen the flame front, therefore decreasing productivity. Decreasing coke in the blend also acts in sinter bonding, decreasing its consistency and increasing crushing and return fines. Moisture addition also influences components mixing, pre-agglomeration, bed permeability and, consequently, sintering productivity. Therefore, optimum conditions must be established for both a given sintering plant and the components in the feed (Dawson, 1993)."

Jan 1, 1998

By R. R. Rogers

Abstract The degree of cathodic protection of steel and the anode corrosion rate were determined when anodes and waters of different compositions were used at temperatures similar to those in domestic hot water tanks. Twenty different anode materials, sixteen of them magnesium-zinc-aluminium alloys, were immersed in six different synthetic waters resembling those to be found in various parts of Canada. The results showed that (1) both the degree of cathode protection and the average anode corrosion rate are affected materially by the composition of the anode material and of the water; (2) poor cathode protection is associated with low anode corrosion rate; (3) when the cathode is fully protected, the anode corrosion rate may be comparatively low or comparatively high, depending upon the composttion of the water; (4) an important relationship exists between the magnesium content of the preferred anode and the composition of the water; (5) the degree of protection is increased as the SO4 + Cl concentration of the water is increased and thus as its specific resistance is decreased. Introduction Fairly recently, the use of the active metal magnesium for the cathodic protection of less active metals has received a considerable amount of attention. This interest has been stimulated by the fact that the wartime demand for magnesium was greatly in excess of the present peacetime demand and there is a natural desire to continue operating the large magnesium plants which were built during the war. Information regarding the use of zinc and aluminium for this purpose also has been published. There is a great demand for domestic hot-water tanks which will resist corrosion satisfactorily. This problem is rather complex in view of the fact that the composition of the water used in such tanks varies greatly and depends upon the locality. The present investigation deals with the effect of water composition and anode composition on the cathodic protection of steel under conditions approaching those which exist in hot water tanks.

Jan 1, 1948

By C. Doyle, J. Brennan, C. Díaz, J. Hrepic, K. Cushnie

"In 1991/1992, INCO undertook a successful R&D program aimed at extending the lining lives of the top blown rotary converters (TBRCs)at its Copper Cliff Nickel Refinery (CCNR) and the electric furnace at INMETCO. At the laboratory scale, this effort was divided into three phases. In the first part, mineralogical work was performed on six refractories that were either currently being used to line these vessels or were considered suitable alternatives. In the second part, this mineralogical knowledge was used to help determine the compositions of slags that would not corrode the bricks at the operating temperature (1600°C) of the above furnaces. Finally, several important properties of the six refractories were measured to complete their evaluation as candidate linings. This paper reports the results of all three phases of the laboratory scale R&D work.The mineralogical work showed that rebonded fused grain magnesite-chrome (RFG-MC) bricks consist principally of periclase with minor amounts of free chromite and trace quantities of silicates monticellite and sometimes olivine. The bricks are principally held together by periclase-periclase direct bonding. Of note, the bulk of the chromite exists as exsolved precipitated blebs within the periclase grains. These likely redissolve at high temperature.Slags on the periclase liquidus coexist stably with these refractories. Examples are presented using CaO-MgO-Al2O3-SiO2 slags at~1600°C.Finally, the two refractories manufactured using close to 100% fused grain material generally outperformed the others in terms of physical properties and certainly were superior in their resistance to slag penetration damage."

Jan 1, 1997

By A S. Leitch

This paper is based on the accident prevention pro-gram carried out in the coal mines of Alberta. It defines the role of the Alberta Mines Branch and of The Work-men's Compensation Board, and relates how a safety pro-gram was initiated. The formation of the Alberta Class 1 Mining Safety Council is also described. The responsibilities of both management and the individual worker are then outlined, and the main features of a successful accident prevention program are delineated. T HE purpose of this paper is not to repeat generalities and platitudes about industrial safety, but rather to relate the experience of Alberta coal mines during the past number of years in their efforts to keep accidents to a minimum. It has been learned from experience that many basic principles are as sound today as they were 20 years ago. How-ever the complexities of modern mining methods and the modern man or miner have created problems that did not exist then.

Jan 1, 1964

By R. C. A. Thurston

AT A FATIGUE SESSION organised by the A.S.T.M. in 1949, R. E. Peterson presented a brief introductory paper ( 1) in which lie referred to a discussion on the fatigue of metals which took place in England in 1849, and then proceeded to review some of the subsequent researches concerning the mechanism of fatigue. In the course of the review, he discussed metallograpl1ic studies with single crystals and polycrystalline materials, studies with X-ray methods, and the application of the electron microscope. During that hundred-year period considerable progress was made toward a better under-standing of the nature of fatigue, although it is probable that even greater attention was directed to the more practical aspects of the problem, such as the effects of notches, temperature, corrosion, surface treatment, residual stresses, and so on. Since then there has been an appreciable acceleration in the tempo of the fundamental work, partly influenced by the rapid development of the theory of dislocations, with the result that our knowledge of the mechanism of slip, the initiation of fatigue cracks, and their subsequent propagation, has still further advanced, although it is by no means complete as yet. The present paper is an attempt to out-line the more recent developments in these basic studies, to correlate them when possible, and to draw attention to those directions in which research might profitably be pursued.

Jan 1, 1957

By A. E. Flynn

THERE is at the present time a revived interest in amalgamation, due to the number of mines starting up, usually on high-grade ore, and utilizing this relatively cheap and convenient means of recovering gold, more especially in their initial stages of production. The marked increased use of the amalgamation process has revealed a dearth of amalgamators and there is no doubt the art of amalgamation has stood still for a generation or two and is not readily applicable to the modern practice of milling gold ores. Mill operators of long experience are learning the art for the first time and are giving it intelligent study, and considerable testing and research work is now being undertaken Most millmen consider amalgamation a simple process, and so it is when we have a clean ore with coarse gold, specially when stamps are used for crushing. In treating Nova Scotia ores by stamps and amalgamation, recoveries of 95 to 97 per cent are common and easily obtained. So-called 'under-water feed' is almost universally used in Nova Scotia and is quite beneficial. The water is supplied through jets between the dies and below the die surface and maintains this space as a live trap which catches the gold particles before they are overground and spoilt for amalgamation. With this method, the portion of gold recovered in the battery is higher than usual and often amounts to 80 per cent of the total gold in the ore, the remaining 20 per cent being caught on the plate. As a continuous amalgamator, the simple plate cannot be excelled. Some of the modern devices having moving or covered and not very accessible plates, which cannot be readily inspected and dressed to keep them in condition, do not give the best results in service. An exception might be drawn in the case of amalgamation of very heavy ore or concentrate which would bank up unless the plate is carried at such a steep inclination as to weep mercury. Difficulties in stamp-mill amalgamation are encountered when acid water is used or when grease is present. Also, certain sulphides and graphitic and talcose ores give trouble, resulting in poor gold recovery and high mer-cury loss. The older literature on gold milling deals with the common troubles of this type and the old-time amalgamator was well able to take care of day-by-day difficulties. When the difficulties were unsurmountable, the ore was classed as 'refractory' and other processes were used.

Jan 1, 1939

By S. J. Cook

The subject of capital and the Canadian mining industry is so broad as to be impossible of comprehensive treatment in brief form. The purpose of the present paper therefore will be only to outline in a meagre and somewhat sketchy way the nature and extent of the mineral industry in Canada and to point out those features which are likely to be of general public interest. Canada's mineral industry has a long and creditable production record. The? value of the output per capita rose from $2.23 in 1886 to a maximum of $26.40 in 1920 and the value of the products from ten million dollars in the former year to almost two hundred and twenty-eight million dollars in 1920. Compared with other primary industries and on the basis of the value of production, mining held third place in Canada in 1920, the premier position going to agriculture and the value of forestry production placing that industry second in the list. In the mineral industry, between six and seven thousand properties are operated annually giving employment to up- wards of sixty thousand employees to whom about seventy-five million dollars is paid in salaries and wages. During 1923, seventeen mineral products reached a production value of one million dollars or over in Canada and in order of the values assigned these were: coal, gold, nickel, cement, cop-per, silver, clay products, lead, asbestos, natural gas, stone, zinc, lime, cobalt, sand and gravel, gypsum and salt.

Jan 1, 1924

By D Maschemeyer

The cobalt production of the Chemical Metallurgical Division of Sherritt Gordon Mines Limited was supplemented, from May, 1962, to June, 1964, by processing 3,500 tons of a calcined cobalt-nickel concentrate. This paper describes the reduction roast -aqueous sulphuric acid leach process and the operating practices employed in recovering cobalt, nickel and copper from this oxidized by-product of a lead-copper operation. Incorporated in this paper is a description of how this process was integrated with the existing ammonia leach -hydrogen reduction process for the recovery of nickel and with the soluble cobaltic ammine process for the recovery of cobalt. Introduction T HE Chemical Metallurgical Division of Sherritt Gordon Mines Limited at Fort Saskatchewan, Alberta, has recently completed ten years of operation utilizing the ammonia leach process for the recovery of nickel, cobalt and copper from sulphide concentrates, matte and other materials amenable to this process. A continuing development program, along with the expansion of certain facilities, has enabled the refinery to attain a production rate of 31, 000,-000 pounds of nickel per year by hydrogen reduction. This represents an increase of approximately 85 per cent over the original design capacity of the plant.

Jan 1, 1965

By S. L. Gertsman

Canadian steel foundry practice has made marked progress during the past decade. Equipment suppliers, development engineers, and foundry personnel have focussed their attention on every phase of the foundry operation, with a resulting lower demand on manpower and materials. Also, more rigid specification requirements as to dimensional tolerances and quality have necessitated improvement and increased control at every stage from the pattern shop to the cleaning room. The growing trend toward mechanization is clearly evident. Equipment such as sand mixers, sand reclamation systems, material handling devices, moulding machines, core blowers, etc., is being increasingly employed by the steel foundryman. This equipment not only increases production but also tends to lessen the human variable so prevalent and disconcerting in the early days of steel founding. The result has been an improved and more reliable steel casting, which is gradually obtaining wider acceptance by design engineers. The purpose of this paper is to discuss briefly some of the practices being used, and also the direction of development that is being pursued by Canadian steel foundrymen.

Jan 1, 1948