Search Documents

By J. Desroches, J. Burghardt, N. Whitney, B. Lecampion, A. Surdi, M. Houston, S. Stanchits

There is accepted evidence that multistage fracturing of horizontal wells in shale reservoirs results in significant production variation from perforation cluster to perforation cluster. In fact, only a fraction of the perforation clusters seem to contribute to production in many shale gas and shale oil plays. In many cases, the orientation of the lateral section of these wells is determined by lease boundaries rather than principal stress directions, and these often do not coincide. When horizontal wells are misaligned from the far-field principal stress directions, the fracture must reorient from the near-wellbore principal stress directions, which are aligned with the wellbore, to the far-field principal stress directions. The primary objective of this study is to learn how various completion designs influence the near-wellbore fracture geometry when such a misalignment exists. A secondary objective is to understand the influence of rock fabric features, such as mineralized natural fractures, on this reorientation process. To understand these effects, eight laboratory hydraulic fracturing tests were conducted using a true triaxial vessel with 914 mm × 762 mm × 762 mm samples of Niobrara shale. Several different completion designs were studied, including the use of fracture initiation slots with several different orientations and the use of perforations selectively located to encourage a smooth transition from the near- to far-wellbore region. The tests were carefully scaled as accurately as possible to provide insight into the field near-wellbore phenomena. Pressure and fluid flux at the wellbore, deformation of the block, acoustic velocity, and induced acoustic emissions were acquired during the tests. Additionally, sized particles were also injected to gauge the fracture width away from the wellbore. After the test, the blocks were dismantled, and the fracture geometry was mapped in 3D. These measurements allow one to clearly differentiate the fracture initiation and the breakdown—meaning the peak pressure—to be clearly differentiated; the fracture was already well developed when the maximum pressure was reached. The study reveals non-negligible tortuosity and aperture restriction in the near-wellbore region. In the field, this would translate to high treating pressures, uneven proppant distribution, and possibly near-wellbore screenouts. The test results show that, of the configurations tested, the best approach is to use deep slots that are aligned with the far-field principal stress directions. The oriented perforation design did not achieve the simple, smooth transition that was hoped for, and instead produced multiple competing near-wellbore fractures and considerable tortuosity. The study also demonstrated that the presence of planes of weakness, such as mineralized natural fractures, near the slot tip can result in poor near-wellbore fracture geometries, even for the best completion configuration. We conclude from these tests that the misalignment of the well with a principal stress direction creates near-wellbore complexity that, in turn, creates uncertainty in proppant distribution and, therefore, production; proppant might avoid up to a half of the created fracture. Regardless of the wellbore orientation, this uncertainty is further increased by the presence of mineralized features in the rock fabric that can strongly alter or stop the growth of the hydraulic fracture. Preventing those effects by changing the completion alone proves difficult, and new strategies are required to ensure a reliable stimulation of shales.

Jan 1, 2015

By R. D. Browns

In his Budget Speech on March 31, 1 977, the Honourable Donald S. Macdonald expressed concern about the financing of investments through new equity issues. He mentioned the need to render more attractive participation in the equity market by investors in all in come brackets. One of the measures introduced in the budget to accomplish this goal is the proposal to increase the dividend gross-up and tax credit in respect of most dividends received by an individual from Canadian companies. The following comments and tables serve to illustrate the impact of this particular proposal.

Jan 1, 1977

By C. O. Swanson

Introduction It is thirty-odd years since I first entered the mining field by working underground at Anyox, which makes 1t clear that I can qualify as one of the older generation and claim the privilege of dealing in generalities and broad impressions. In this position I find it interesting to re~ view the salient changes that have taken place during the past quarter-century and indulge in some speculations concerning the future, with the hope that my comments may be of value to others engaged in the field of mining geology. As indicated by the title, the treatment is a perspective from a single viewpoint rather than an attempt to give a complete and impartial analysis. This plan, while deficient in some respects, has the advantage of being more specific than one based on .a. compilation of opinions. An additional advantage is brevity, which would be difficult to obtain on a subject of this scope if it were viewed from all angles. In conformity with the general plan, specific references to the literature have been avoided as much as possible, although a number of publications of general nature are listed at the end of the paper. This procedure is intended to give credit to the sources used without making them in any way responsible for the interpretation. The starting point for the discussion is the situation as it existed twenty-five years ago, when, as a recent graduate, I first had a fairly complete picture of it. However there is one impression of an earlier; stage that seems worth mentioning. In one of my first courses in geology the statement was made that some of the leading authorities of the previous generation, who guided geological thought at about the beginning of the century, were inclined to question the value of an association with mining. This attitude was no doubt exceptional, and certainly it was not adopted by the students who laid the groundwork for mining geology in North America. But its existence even in a limited circle is significant m showing how far the application of geology has advanced as the result of the investigations started during the first part of this century.

Jan 1, 1949

By Colin E. Dunn

The high mobility of gold within the plant kingdom results in detectable accumulations of gold in many plants. Concentrations vary within individuals, among species, and with seasons. From an evaluation of the chemistry of easily acce sible organs of common pecies in the northern forests, it is concluded that alder twigs (or leaves) and conifer bark scales are the vegetation components of greatest use in the earch for concealed gold mineralization. Maximum anomaly enhancement is obtained from twigs collected in the spring. Examples are given of urvey conducted in the La Ronge Domain using 1) jack pine bark (A nglo-Rouyn and Upise Lake areas) ; 2) alder twig (McLennan Lake) ; 3) black spruce bark (Rod Zone near Mallard Lake, and at Waddy Lake) ; and 4) multi-media (Tower Lake). At the latter two sites gold-bearing till is blanketed with late glacial material. Gold enrichment in the plants suggest that the roots are ab orbing gold from the underlying till. Complex processe control the uptake and retention of gold in plants. An understanding of these processes pem1its biogeochemistry to assist in locating near- urface mineralization .

Jan 1, 1986

By G. P. Demopoulos

The solubilities of calcium sulfate in HCl-CaC1z-H20 solutions up to 100°C were successfully modelled with the aid of OLI software after bringing proper modification to it. Modelling, more specifically, was carried out with the help of the Environmental Simulation Program, V-6.6.0.4 (www.olisystems.com). New model parameters were obtained by regressing the solubility data. A private databank was established by adding the newly defined model parameters and the calcium sulfate hemihydrate phase that is not included in the original OLI database. The McGill-modified OLI software was successfully applied not only to modelling solubilities but also the transformation of the various CaS04 phases, namely dihydrate, hemihydrate and anhydrite. In this paper, the modelling methodology will be discussed along with a comparison of the capabilities of the newly developed model vs the original OLI model.

Jan 1, 2005

By S G. Bergdahl

Underground mining in Sweden is today characterized by mechanization and automation, owing to the rising cost of labour. Drilling in drifts and tunnels is still essentially done with jackleg drills, but rigs wh1ch make it possible for one man to operate two or more drills are now frequently used. Large jumbos for longhole drilling, with two drills operated by one man, are used, especially in sub-level caving. A special drill-rig for drilling through overburden and blasting without removing the overburden has been successfully used in canals and also in ports, where blasting is per-formed under water. The increased use of mining methods based upon long blastholes is a result of the development of equipment for drilling long straight holes. The most common mining method in Sweden is sub-level caving. Extensive research, with model tests, has been carried out in order to determine suit-able dimensions of drifts, sub-levels and drilling patterns. The results have been tried in practice and have given increased yield and less waste rock in hoisted ore.

Jan 1, 1963

By A. Zaidi

"The mining and metallurgy industry is highly energy intensive and one of the largest energy users in Canada. Energy costs are also a major component of total production costs in this industry as described in the 1990 Report of The Canadian Industry Program for Energy Conservation (CIPEC). For some plants, energy costs are reported to be up to 30% of total production costs. Therefore, a reduction in energy costs provides an opportunity to improve industry profitability. The specific energy intensity and production costs can be reduced by using modem energy efficient natural gas technologies. In addition, these technologies often improve product quality and increase productivity. Natural gas not only offers economic benefits, but is also environmentally benign as compared to other major energy sources. Emissions of NO"", CO2 particulates and SO2 are lower with natural gas than other fossil fuels.This paper provides a brief overview of some state-of-the-art gas technologies for the mining and metallurgy industry including cogeneration, oxy-air-fuel burners, ceramic immersion tube heaters, direct gas contact process, low NOx burners, and energy efficient liquid heating systems.CogenerationCogeneration is defined as the simultaneous production of electricity or mechanical power and useful process heat from a single fuel source. One of the primary considerations in selecting a cogeneration system is the relative quantities of electrical and thermal energy which are to be produced. Two types of systems are discussed below."

Jan 1, 1993

By T. Fekete, D. L. Flocks, R. T. Hart

The plugging effect of bacteria was investigated by injecting various concentrations of dead bacteria cells though sandstone cores. Pressure profiles along the cores were recorded periodically during the injection cycles. The plugging effect was analyzed using a plot of the ratio of reduced permeabilities to the initial permeability versus input volume. Results indicated that Tock permeability has little effect on plugging, but that the concentration of bacteria in the injection water has a significant effect on plugging characteristics. The pressure profile curves showed that bacteria penetrated several inches through the core but that the greater portion of the bacteria accumulated at the in-put end of the core.

Jan 1, 1960

By R. A. Hemstock

AREAS in which the surface de-posits consist of organic material -known in some parts of Canada as muskeg and in Europe, more generally, as peat lands -have long been some of the least rewarding of lands of the north temperature zone. Even in such countries as Great Britain, Holland, and Denmark where a good deal of incentive exists to develop all available land, the use of peat land has been negligible except as a source of fuel. Only recently have efforts shown promise in re-claiming these lands for farming or for forestry. Russia has large areas of peat and use is made of it for power generation. The Russian people have also ?developed a variety of machines for handling peat, which would indicate that they are well ahead of the Wes tern World in their technical and physical ability to solve some of the problems. Certainly in Canada, where there are over 500,000 square miles of muskeg, the economic aspects of this problem are important. This is especially true in considering the shifting emphasis to northern development. Not only is muskeg in possession of great stretches of terrain, thereby rendering it useless for agricultural purposes, but it is apparently moving into forested areas and reducing their productivity. In addition, it lies as a great barrier to movement in the search for and development of such natural resources as petroleum, natural gas and minerals generally. This situation has long been recognized in Canada but only recently have organized efforts been made to study the problems and search out ways of overcoming them.

Jan 1, 1958

By E. C. Sanford

A laboratory-scale batch extraction unit and operating procedure for studying the hot-water separation of bitumen from Athabasca tar sands are described. The extractor evolved from earlier units and has been in use by Syncrude Research for the past 10 years. By using a unit such as this, it is possible to study tar sand feed quality and the effects of chemicals on the hot-water extraction process, while process variables are held constant. Data are presented to demonstrate the importance of surfactants to the process and the interrelated role of inorganic bases and surfactants.

Jan 1, 1979

By Dong-Hyeun Koh, Yun-Soo Lee, Min-Seok Kim, Hyoung-Wook Kim

High strength AA7068 (Al - 7.88 wt.% Zn - 2.68 wt.% Mg - 2.07 wt.% Cu) aluminum alloy strip was successfully fabricated by horizontal-type twin roll casting. A simulation technique was used to obtain the range of casting conditions for fabricating strip without defects. The cast strip with thickness of about 5 mm was hot rolled, intermediate annealed, cold rolled to final thickness and subsequently annealed at various temperatures. Tensile properties of annealed and the aged specimens were evaluated at ambient temperature. Tensile strength and elongation of the annealed sheet are about 365 MPa and 28%, respectively. Also, the tensile and yield strength after the aging at paint baking condition (180 °C x 0.5 h) are 586 MPa and 551 MPa, respectively. Therefore, it is expected to show good formability prior to press or stamping and also provide high dent resistance after paint baking treatment.

Jan 1, 2015

By W. B. Gallup

"The Athabasca Bituminous Sands have been subject to sporadic investigations since the beginning of the century. It is probable, however, that much of what has been learned and achieved concerning the deposit has been accomplished in the last few years.Current exploratory techniques, generally speaking, involve a moderate amount of coring. Electrologs and often radioactive logs are run on most holes and certain types of these archieved excellent qualitative analysis when backed up by some core analysis for calibration. Exploration - is moving back from the river and consequently a permanent network of access roads has been developed within the last few years. Most of the operations take place in the winter time. There are about 90 permit holders at the present time.Some exploratory techniques are set up to go into recovery experiments where rich tar beds are found. It is probable that in the final analysis there will be several successful methods of extraction and that both mining and various in situ techniques will be applicable depending upon the problem locally."

Jan 1, 1960

By J. Gray, J. Peck

As the turn of the century approaches, traditional open pit mining methodologies and processes are being modified through the introduction and use of new technologies. As in other industries, the personal computer is dramatically changing the traditionally conservative mining industry by allowing mines of varying size and capacity to increase their productivity and efficiency through the use of easy to use, office software. Computer-based monitoring and control systems are also being used more frequently to measure and optimize, in real-time, the performances of operating equipment. When communicated to an end-user, this information can provide accurate and timely answers to questions of how much, where, when, and by whom. This capability forms the foundation of a more comprehensive, proactive management and planning facility where, ultimately, information acquired from the producing equipment will be used to optimize and control machine and human activities. As these technologies mature and become essential tools in a mine, they will eventually serve as the basis for more robotic and autonomous mining operations.

Jan 1, 1999

By Robert J. Shank

This paper describes the Federal Government assistance available for northern mining development. The paper commences with a discussion of why the Federal Government should give assistance to northern mining development. It then uses a hypothetical case of a company which has a property it wants to develop to list the sectors within the . Federal Government that would have to be consulted in order to obtain federal financial assistance. The paper also outlines the type of information a company must be willing to provide the government in order to qualify for such assistance.

Jan 1, 1978

By Roger M. Jones

This paper comments on developments in bulk shipping which will be of direct interest to those who are considering the shipment of dry bulk minerals out of Nova Scotia by water. Various conveying systems, and the slurry system of loading, are considered, and the role of deep water ports as a catalyst to other industries is stressed.

Jan 1, 1971

By X. Gu

Mining operations, especially surface coal mines, have great impacts on the local ecosystem and the environment. However, it has been a common practice in mine design that the economic evaluation considers only the operating and capital costs, while the costs incurred due to ecological damage are left out. Such practice underestimates the total cost of mining and ignores the difference in ecological impacts between different mine design alternatives. With growing interest in sustainable development, the mining industry is under increasing pressure to operate not only based on economic and engineering principles but also on principles of sustainability. Therefore, estimating ecological costs of mining and considering such costs in the mine design process is an important step towards reducing ecological impacts at the design stage. The objective of this paper is to quantify the ecological costs of open pit coal mining and to demonstrate the influence of such costs on the ultimate pit design. The ecological costs of mining are estimated based on the areas and types of land damaged by mining activities and the carbon emission from energy consumption. Four major components of ecological cost are identified, namely, lost value of direct eco-services, lost value of indirect eco-services, prevention and restoration costs, and the cost of carbon emission from energy consumption. Necessary equations are given for estimating these costs. An algorithm is described for ultimate pit optimization in coal deposits with near-horizontal coal seams. A case study is presented in which the ultimate pits with and without ecological costs are optimized and compared to show the influence of ecological costs on the pit design outcome.

Aug 1, 2013

By J. C. White

"During the early development of the Mattabi Mine in 1970, discussions with the Ontario Government revealed their policy of prohibiting, as much as possible, the development of new, isolated, single-industry townsites. Subsequently, Mattabi located its first housing in the Township of Ignace, which is situated 50 miles from the site of the mine and plant. Over 200 employees now commute 100 miles daily to and from work.This paper describes the experience gained and discusses the advantages and disadvantages of a remote townsite."

Jan 1, 1976

By Jodi Wilding, Barry Lurnsden

The implementation of new technology to mineral separation operations requires rigorous testing to confirm the technology&apos;s technical and economic benefit. The Jaguar Mine owned by Jabiru Metals is located in Western Australia and sequentially separates a copper concentrate and then a zinc concentrate. Fine grinding (80% of zinc in tail is <25µm) is required to achieve efficient mineral separation. All mineral losses are therefore fine mineral losses, and so improvements in metal recovery must focus on this fine mineral. Magnetic aggregation technology has been shown to increase the recovery of fine paramagnetic minerals so it was an appropriate technology to evaluate at Jaguar. Testwork commenced in the copper circuit and it was found that there was a substantial reduction in copper in copper tail and an increase in zinc recovery to the zinc concentrate. The increase in zinc recovery in the latter zinc circuit was an interesting result and initiated the second stage of testwork that was to install and test a second magnetic conditioning unit in the zinc círcuit. This showed a further increase in zinc recovery. Magnetic conditioning technology has now been fully evaluated in the plant and is now part of the Jaguar flowsheet.

Jan 1, 2011

By T. E. Wakefield

"Final Galloway (stage) designs for vertical drill and blast shaft sinking projects evolve from complex thought patterns which integrate operational processes, systems and methods of communication, power supply, drilling, blasting, ventilating, mucking, supporting, surveying, dewatering, sealing, concrete lining and shaft furnishing. Attention to ergonomic design detail at the shaftsman / structure interface is at the heart of safe and successful multi-deck working platforms. For economy the end product must have a low mass to reduce suspension rope end loads to be able to use smaller suspension hoists and have lighter headframe structures, be robust to withstand concussion damage, be easily constructible on site, be maintainable in the shaft barrel, and comply with safety and legislated standards. This paper’s ambition is to describe a systematic design framework and sequenced thought process that delivers a product that is engineered with excellence, illustrated by making use of two designs that evolved during recent Galloway projects, one destined for a large diameter man/material shaft, the other for a ventilation shaft. The stage engineering iterative process starts with mapping permanent and sinking hoisting layouts, followed by laying out horizontal deck plans, mostly constrained by the permanent shaft purpose and configuration, whilst maximizing openings to enable muck to be removed rapidly for the best sinking cycles. Concurrently the designer needs to understand the chosen sinking methodologies in conjunction with crewing to determine the number of decks and fix their spacing. Insufficient access to move and line up formwork, set reinforcing rods and pour concrete in the confined spaces of the stage is an inherent major risk to be mitigated. An iterative and integrative process follows for the primary configuration which delves into increasing design detail, accommodating all other methodology influences, resulting in 3D layouts for further risk assessment, review and fine tuning by seasoned shaftsmen. INTRODUCTION Documented colliery shaft sinking practice from the late 1800’s makes reference to purpose built walling (bricked lining) cribs with floors suspended in sinking shafts, thereby allowing shaft lining to proceed concurrently with the excavation. Improvements were made by Sir William Galloway who introduced two decks supported at the corners by angle irons. The sinking stage, or Galloway, has developed substantially over time to be the in-barrel heart of the sinking operation, with overwhelming complexity for those who have to design one for the first time."

Jan 1, 2019

By Hal. Oliver

MR.]. G. TRAILL: My only excuse for contributing to the discussion on Mr. Hall&apos;s interesting paper is that I had the good fortune to be employed at Noranda during those romantic years, 1927 and 1928, when construction was at its height. The mine was in course of being rapidly prepared and brought into production, and the initial difficulties in crushing-plant and smelter were being met and overcome. They were stirring days, and perhaps those members who were with the second Empire Mining and Metallurgical Congress in 1927 sensed the atmosphere of excitement and activity that prevailed. Early History. Noranda must surely possess some of the most remarkable ore-bodies known to mining men, and the story of their development is pure romance. Ed. Horne&apos;s faith in the property, and the persistence of Thomson and Chadbourne, were richly rewarded in the end, but only after some very thin times had been experienced. In those early days access to the district was by the Kenojevis river and various portages to Osisko lake, on the shores of which the mine and smelter and the town of Noranda now stand. But all the early work was done on the Chadbourne claims, more than a mile to the west; through the b~sh. I have read a log of the events of that period, and through the whole tale of hard work, discouraging developments, occasional shortages of food, and constant danger from forest fires, can be read the faith and persistence of the men in charge. The Chadbourne ore was of that well-known type which, though just too low-grade to pay (with gold at $20 per ounce), is yet sufficiently encouraging to lead one on in the hope of striking something better. It was only as a last resort that work on the Chadbourne claims was suspended and a diamond drill brought to the gossan-covered hill beside the lake. The diamond-driller told me his version (it may be exaggerated) of how the position and direction of the first hole were decided on. He was told, "You might as well set up your drill here, and drill in, say, that direction". I believe that the first hole went through the richest ore ever found at Noranda. After the drill had gone through about 150 feet of solid sulphide ore running 17 per cent copper and 4 dwt. of gold per ton, it passed into barren rock, but the diamond-driller expressed the opinion (I wonder how he knew)) that the hole would come into ore again before long.

Jan 1, 1937