Search Documents

By K. Ebrahimi-Nasrabadi

The dependence between the extent of conversion of cryptocrystalline magnesite to caustic magnesia was studied experimentally in the temperature range of 400?1200 °C and for calcination times up to 8 h. A TGA?DTA analysis showed that decomposition begins at temperatures as low as 340 °C and is completed at 600 °C. Measurements of specific surface area (SSA), iodine adsorption number (IN), crystallite size, and loss on ignition were carried out to characterize the product quality. It was found that while all the parameters are dependent on the extent of calcination, densification of the product caused by grain coarsening affects their final values. As a consequence, SSA and IN went through a maximum with time. The study showed that high quality caustic calcined magnesia can be produced in a narrow range of temperature (600?650 °C) and time (1?4 h). Medium quality caustic calcined magnesia can be made within a wider range of parameters.

Aug 1, 2013

By A. S. Eve

The detection of magnetic dykes by using magnetic variometers is the oldest application of. geophysics to mining, and is also one of the more simple and certain methods 0f locating such deposits. As a result of recent improvements in the instruments, it is now possible to find the dyke, deter-mine with magnetic variometers its strike and dip', with fair accuracy, and to estimate the approximate depth of overburden when there is no outcrop. The application of electrical methods may be used to distinguish mineral from diabase dykes. The authors have had an opportunity of making surveys with the modern Askania types of vertical and horizontal variometers over magnetic dykes in the Sudbury region. The interpretation of the results has been confirmed by diamond drilling in some cases, and by experiments over models. The variometers used were the standard form of Askania instruments (1). The sensitivity of the horizontal type was 17.2 gammas per division, and that of the vertical variometer double this quantity. To make a preliminary survey of the district, parallel lines were laid off two hundred feet apart running north and south, and readings were taken with the vertical variometer every 100 feet along these lines. This can be done very rapidly, and when an indication of a magnetic deposit is found, the readings may be taken every hundred feet, or less if the size of the deposit warrants smaller intervals. If the deposit is a vein or dyke, the readings along the adjacent lines immediately indicate the strike of the body. Thus the presence and strike of a magnetic dyke, whether of mineral value like the pyrrhotite and nickel deposits of the Sudbury district, or simply a worth-less diabase dyke, is simply and rapidly found.

Jan 1, 1932

By G. Deschênes

"In 2013, as the prices of precious metals dropped, investors moved their positions to equity markets for higher returns. As a result, the price of gold dropped further to below US$1200 per ounce, prompting additional substantial outflows from gold investments. In response to lagging gold prices, major gold producers initiated large asset write-downs and cost-cutting programmes. In 2015, this trend continues and gold mining stocks are close to lows not seen since the global financial crisis (GFC) of 2008. In the current economic climate many projects have marginal economics, and the number of projects that have competitive development and production costs is declining. A competitive edge is particularly important with the decreasing grades of orebodies, increasing complexity of the mineralogy, and increasingly demanding environmental constraints. In addition, higher cost producers seek to optimize their process t o reduce operating costs.This paper presents some highlights of three case studies on optimization of gold leaching strategies that improved the economics of brownfield projects. Processing of sulphide-bearing ores was optimized by using the synergy between cyanide, lead nitrate, and oxygen. The outcomes were significant reduction of retention times while maintaining or increasing gold extraction and reducing cyanide addition and effluent treatment costs. A stirred tank reactor experimental programme led to direct implementation of reliable leaching strategies from laboratory scale to production. This approach resulted in savings of $2.2 million to $15.2 million on the three brownfield projects discussed in this paper."

Jan 1, 2016

By K. Sun

The exothermic behavior of the intermetallic reactions inside an Al-Mn metallic powder compact and its assimilation fundamentals in molten aluminum were examined. In this study cylindrical compacts were manufactured and tested. The experimental work involved simultaneous temperature measurements of three thermocouples as well as detection of the apparent weight of the cylindrical specimen during its assimilation in liquid aluminum. The details of the intermetallic reactions prior to the compact complete disintegration were investigated by microscopically studying the morphology and local composition in a partially reacted compact. The variation of manganese concentration in the melt was determined by chemically analyzing the samples taken from the molten aluminum at specific time intervals. The exothermic reaction increases the compact's temperature above that of the liquid aluminum. In tandem with this exothermic reaction, the compact is suffering a swelling action. This swelling action disintegrates the cylindrical specimen, which is assimilated into the liquid aluminum. The intermetallic reactions proceed in a stepwise manner. Both the bath temperature and the compact composition impact on the exothermicity of the intermetallic reactions. However, when the amount of Mn in the compact is greater than 75-wt%, the maximum centerline temperature rise is slightly reduced as Mn amount increases.

Jan 1, 2004

By Fr. -W. Bach

In the past years the enormous weight saving potential of magnesium sheet has been demonstrated by various research projects all over the world. It has been shown magnesium flat products can benefit automotive, aviation, machine tool and consumer electronics industries. Major material problems such as poor formability, corrosion resistance and high production cost still inhibit the application of magnesium sheets in large scale production. The present contribution outlines achievements in casting and rolling technology. The authors developed an adapted strip casting process in which near-net-shape rolling feedstock of several wrought alloys has been produced. During the rolling process, various parameters were varied in order to modify the microstructure and surface quality of sheet. Several temperature cycles, strains, lubricants, roll surface structures and roll coatings have been analyzed. The sheets were examined and tested in deep-drawing experiments. Suitable rolling schedules have been developed for standard and modified wrought alloys. The study concludes with an overview of current industrial solutions and an estimation of the potential cost savings that might result from the adaptation of the process that has been developed.

Jan 1, 2006

By L. B. Tsymbulov, N. A. Fedorova

The equilibrium of exchange reaction (Cu20)+[Ni]=(Ni0)+2[Cu] taking place in the course of interaction of metallic nickel-containing copper melts with different oxide melts (Cu20-NiO, Cu20-NiO-Si02, Cu20-NiO-FeO(Fe203)) in the area of their homogeneity has been studied. The studies, based on the known value of equilibrium constants and defined copper and nickel activity indices in metallic melts and equilibrium concentrations of Cu, Ni, Cu20 and NiO, determined the YNio/ycu2o ratios in the oxide melts of the above systems. For the equilibrium between nickel-containing copper and binary oxide melt Cu20-NiO, values of YNiO and Ycu2o were determined both by calculation and experimentally. Based of the data conclusions regarding oxide melts construction are presented.

Jan 1, 2007

By M. Kamyab

Transportation of fluid and slurry (fluid and solid particle mixtures) in a pipe and annulus space has been the focus of numerous studies. There are different parameters to be considered when studying slurry transportation. These include slurry velocity or flow rates; fluid properties such as density and rheology; and solid particle properties including concentration, density, shape and size. Also the angle of the flow conduit, rotation of the pipe and possible eccentricity of the annulus are other factors which influence slurry transport characteristics. Although a number of analytical, numerical and empirical equations as well as numerical simulations have been developed for studying the flow and slurry transport characteristics, the results need to be validated against either field or lab data. As performing field tests is costly and time consuming, conducting simulations at the laboratory scale appears as a good alternative. Different flow loops have been designed to study slurry transport behaviour in different science and engineering disciplines including oil and gas and mining. However, few of these consider, in particular, cuttings transportation in small size annulus space. The flow characteristics appear to be very different when slurry travels within a small size annulus, in particular when the fluid velocity is high. In this study, a review of some of the existing slurry flow loops will be conducted. Then the details of a slurry loop, which has been designed and commissioned for the purpose of studying cuttings transport in a small size annulus space for applications in drilling mineral exploration wells using coil tube technology, will be presented.

Aug 1, 2013

By L. M. Wang, G. P. Jiang, Y. Jiang, Liao. W. S.

ABSTRACT The authors measured porosities and permeabilities for cores from a low-permeability sandstone uranium deposit in Inner Mongolia. Features studied included fine pore structure, mineral composition, cation exchange capacity, granule appearance, and cementing features. In general, grading of the grains was relatively poor, which decreased the radii of the pore channels. The pore throat distribution was significantly heterogeneous. Pore channels ranged from small to large, but the lack of large pore channels led to low permeability. Cementation by calcite and clays, including montmorillonite, chlorite, and kaolinite, resulted in pore channel narrowing, further decreasing the permeability of the formation.

Jan 1, 2014

By R. Argane

In this work we assessed the geochemical behavior of concentrator tailings deposited at the abandoned mines of Zeida and Mibladen (Upper Moulouya, Morocco), using physico-chemical analyses, mineralogical characterization, acid base accounting and weathering cell tests. The aim of the study was to evaluate mine drainage quality and to assess metal mobility from these concentrator tailings. Chemical analyses show that the Upper-Moulouya abandoned tailings contain relatively high quantities of lead (0.261 to 0.594 % wt). Mineralogical analyses reveal the abundance of neutralizing minerals (calcite, dolomite, ankerite, and aluminosilicates) which influence mine drainage and metal mobility in mine tailings. Leachate analyses from weathering cell tests show alkaline conditions, small conductivity values, and low solubility of Pb-mineral phases. According to these results, abandoned mine tailings in the Upper-Moulouya district have very low potential for generation of contaminated mine drainage and for leaching of heavy metals. However, the inhalation of tailings exposed to winds generate dust problem facing the local population and may cause health consequences.

Aug 1, 2013

By K. El-Ouassiti, M. Zouadi, C. Bazin, D. Hodouin

Data reconciliation techniques are used to attenuate the effect of measurement errors and estimate unmeasured variables. This paper illustrates the application of data reconciliation to hydrometallurgy processes using measurements from leaching and solvent extraction obtained from laboratory experiments. The application of data reconciliation provides an efficient way to detect gross and systematic errors and produces reliable performance indices for process evaluation.

Jan 1, 2005

By Xiang-dong and Zhu, Xia-jie Hao, Yi-lin Fan, Quan Jiang, Lian-xing Hu, Xia-Ting Feng, Shao-jun Li

"Columnar jointed basalt (CJB), which typically originates from lava flows, is characterized by a special geological structure. The joint network inside the CJB is self-organized into a rough hexagonal arrangement. The field test and measurement during the unloading excavation showed that the columnar joint sets and other internal joint sets not only are important for determining the mechanical properties of the CJB, but also induced its asymmetric unloading deformation and failure. A constitutive model, which considered mechanical deterioration of both the joint sets and rock blocks, was also developed to simulate the unloading behaviour of the CJB. The crack-confinement supporting method for surrounding CJB was developed to overcome the failure of columnar jointed rock mass in the diversion tunnel. Application to the CJB segments of the diversion tunnels in the Baihetan project indicated that this supporting method was reasonable and efficient. INTRODUCTIONColumnar jointed basalt (CJB) rock mass, which typically originates from lava flow, is characterized by a special joint structure. The joint network of the CJB is self-organized into a roughly hexagonal arrangement and leaves behind an ordered colonnade. The widely accepted current view regarding the formation of columnar jointing involves a thermally induced contraction–cooling mechanism (Peck and Minakami, 1968; Degraff and Aydin, 1987; Budkewitsch and Robin, 1994; Lore et al., 2000; Goehring et al., 2006). Although the columnar basalt formation mechanism is fairly understood, the geotechnical characteristics of such rock mass are not well established. In practice, joint sets always induce the multi- failure modes of surrounding rock in the tunneling space (Ibarra et al., 1996; Waltham and Swift, 2004; Mahendra and Bhawani, 2008).According to conventional wisdom in rock mechanics, structural joints affect the mechanical response of rock mass by introducing strong anisotropic effects (Barton and Bandis, 1980; Hudson and Priest, 1983; Brady and Brown, 1985). The columnar jointed rock mass should be considered an anisotropic material given that the joint sets are distributed with some principal directions and characteristic spacing distributions (Cundall and Fairhurst, 1987; Hoek et al., 1998; Wu and Wang, 2001; Budetta and Nappi, 2011; Fortsakis et al.,2012). Columnar jointed rock mass would result in structurally controlled failure patterns, even serious disasters during underground excavation because of the low shear and tensile strengths of intensely joints (Gencer,1985 ;Ishida and Uchita, 2000; Jia and Tang, 2008). The CJB rock mass in the Baihetan hydropower station has exhibited serious stability issues, including sliding, fracturing and even collapse (Shi et al.,2008). Therefore, the geotechnical and geomechanical characteristics of such rock mass should be assessed through in situ investigation and numerical analysis to minimize future accidents during underground unloading excavation."

Jan 1, 2015

By K. D. Peaslee

Slag splashing is an important development that has dramatically improved BOF vessel campaign life and reduced operating costs. This paper highlights research from physical modeling work using a 1/8-scale room temperature model BOF and slag characterization studies from several plants in North America and China. In the model studies, gas flow rate during blow and viscosity of the liquid were found to be two of the most important factors to changing the overall rate of liquid splashed onto the vessel sidewalls. When the flow rate was increased or viscosity decreased, the lower regions of the walls were splashed at a much greater rate. It was also shown that by changing the lance height, more liquid was deposited in the upper regions of the vessel at the expense of lower regions. Reducing the number of nozzles was found to be the most effective method of selectively coating a particular vertical section of the wall. Studies of BOF's using slag splashing in North America and China showed a difference in the melting characteristics of the final slag. Generally, slag splashing is successful when the melting point of the slag is 220-270°C below the tap temperature to maintain a balance between fluidity and refractoriness.

Jan 1, 2004

By F. Habashi

Lead is an ancient metal, has been produced to-date from its ores exclusively by pyrometallurgical route. The process suffers from high operating cost and excessive pollution problems. Extensive research has been going on since the beginning of the twentieth century to find a non-polluting process for its production and a solution for its complex refining scheme. It has been assumed correctly that the hydrometallurgical route should be the most promising. Pilot plants have been constructed and operated for a reasonable periods, but no process has proved to be satisfactory. As a result, a number of smelters and refineries have been shut down. The present review analyses the situation and suggests that the best route to treat lead sulfide concentrates is by leaching with fluoroboric acid, HBF4, containing ferric fluoroborate, Fe(BF4)3, and electrolyzing the solution in a diaphragm cell - - a process recently invented by Italian metallurgists. In this process, any silver present in the concentrate remains in the residue together with elemental sulfur and can be recovered by known methods.

Jan 1, 2008

By W. S. Dyer

Introduction In northern Ontario, refractory clay is found on four rivers of the James Bay watershed: the Abitibi, the Mattagami, the Missinaibi, and the Moose. The clay all belongs to the same geological formation ( the Mattagami of Lower Cretaceous age) , and occurs within a structural depression or 'basin', the boundaries of which have never been defined but which appears to cover at least 1,500 square miles of territory. The recently constructed James Bay extension of the Temiskaming and Northern Ontario railway crosses the northeast end of the basin at the Onakawana lignite field, which by rail is 126 miles north of Cochrane, 605 miles north of Toronto, and 60 miles southwest of Moose Factory. Smoky Falls, the northern terminus of the railway owned by the Spruce Falls Power & Paper Company, Limited, is 7 miles south of one other point in the basin, i.e., the outcrops of refractory clay, sand, and kaolin at the foot of Long rapids on the Mattagami river. Smoky Falls is 50 miles north of Kapuskasing. In a very early report(l) , Dr. Robert Bell, of the Geological Survey of Canada, described '"light coloured marl in horizontal beds" from the Missinaibi river, and noted that the lignite also occurring in the river was probably :associated with the marls. This was undoubtedly the Cretaceous refractory day. Other early writers noted the occurrence of fire-clays, but it was not until Joseph Keele(2), of the Geological Survey, visited thee region in 1919 and studied the clays that their real significance was known.

Jan 1, 1933

By A. Lopez-Valdivieso

Particle size enlargement processes play an important role in solid/liquid separation, and in beneficiation unit operations. In the latter, not only the size of the formed aggregates but also their surface properties are very important. Oil agglomeration has a special place among such processes: it is a selective process in which hydrophobic particles are agglomerated into hydrophobic agglomerates which can be recovered by flotation. This explains the broad applications of oil-assisted beneficiation processes not only in the beneficiation of fine coal, but also in agglomerate flotation of many different types of ores, and in coal/gold agglomeration.

Jan 1, 2004

By M. Barati

A collaborative research between University of Toronto and Hatch was conducted to understand and optimize the process conditions pertaining to a novel steelmaking technology. In this technology, known as CRISP, direct reduced iron is continuously melted and refined in a stationary electric arc furnace. The major challenge against continuous operation of the electric furnace was identified to be minimizing the corrosion of the refractory in order to achieve uninterrupted operation for a minimum of one year. Theoretical analysis and bench scale experiments together with two pilot runs resulted in defining an operating window for slag chemistry that would minimize chemical attack to the refractory while satisfying the oxidizing conditions required for sufficient decarburization. An analysis of the process in terms of energy consumption and emission of greenhouse gases revealed that it is superior to the current batch DRI-based steelmaking technologies.

Jan 1, 2011

By C. Morlot, C. Auvray, E. Fourreau, J. Talandier

"During the excavation of underground galleries in a rock mass, reorganisation of the stress field around the site results in damage to the surrounding material. In the framework of research undertaken at the ANDRA underground laboratory in France, galleries have been excavated in a Callovo-Oxfordian argillite formation. The damage has manifest as a number of fracture systems in the adjacent rock. Observations have shown that fractures generated during excavation and storage exploitation are able to self-seal during re-saturation of the site in the post-closure stage. Although indirect evidence for argillite self-sealing has previously been reported, from experiments performed both in situ and on samples, no direct observations of self-sealing have yet been made.For the present study, we performed a range of self-sealing experiments using a newly-developed triaxial compression cell placed within a nano-CT scanner with a 10 µm resolution. The body of the compression cell is X-ray transparent, allowing sample healing to be monitored directly. The samples contained an artificial fracture that had been generated in the laboratory, into which a fluid was injected. The fractures were orientated either perpendicular or parallel to the plane of anisotropy of the material. Our initial results demonstrate that when fluid is injected perpendicular to the plane of anisotropy, the flow-rate has no apparent influence on the kinetics of fracture closure. Permeability varies significantly, from 2.10-14 to 2.10-18 m2 over 116 hours. Post-test observations of the fracture lips show swelling that appears to be orientated perpendicular to the fracture plane and therefore parallel to the plane of anisotropy. Initial results for an injection parallel to the plane of anisotropy suggest that, in this case, the rate of flow affects the kinetics of fracture closure. For a flow-rate of 0.25 ml/min, closure begins after around one minute. In contrast, for a rate of 0.05 ml/min, it is necessary to wait several minutes before partial sealing of the zone is observed. The reduction in permeability is again significant, from 2.10-15 to 4.10-18 m2 over 96 hours. After completion of the test, swelling was observed in elongated zones that lie parallel to the fracture plane and therefore to the plane of anisotropy."

Jan 1, 2015

By David S. Wong

With air emission limits for total particulates continually tightening, management of `potroom dust' or airborne particulates from aluminium smelting potrooms is of increasing importance. To better understand how settled and airborne particulates are generated within a potroom, methodologies have been developed to sample and analyse the compositional signature of dust, in relation to its sources. During a smelter case study, these methods allowed tracking of mineralogical phases in dust across a range of potroom locations, showing that the mechanisms of dust generation do vary spatially and vertically in a potroom. Such methodologies may also be applicable to other metallurgical industries.

Jan 1, 2011

By Kaiwen Xia, Bibhu Mohanty, Per Svedensten, Sheng Huang

"The mechanics of crushing and grinding operations in mining and excavation processes has been investigated in a laboratory simulation study. It employs a multi-particle bedded rock target, which is subjected to multiple impacts. The impact set-up consists of a Hopkinson pressure bar and a Piston-holder system. The apparatus, employing a 38 mm diameter pressure bar, was used to apply varying but calibrated dynamic loading force on the rock particles. The energy consumed by the sample during fragmentation was determined by considering the energy carried by the incident wave and the reflected wave. The Pistonholder system is used to hold rock samples and to recycle fragments after each test for particle size analysis, for single as well as multiple impacts. The feed size selected was in the range of 9.5 to 12.7 mm for all rock samples, and the impact velocity was set at 14 m/s. Two strong granitic rocks and a relatively weak limestone were the target rocks. The resulting particle size distribution after each set of impacts, ranging from single to 10 consecutive impacts, were analyzed, and various size distribution functions (i.e. Rosin- Rammler, Swebrec, Grady and Gilvarry functions) were fitted to compare their suitability in predicting the fragment size distribution for each rock type. INTRODUCTIONCrushers are widely used in the mining industry all over the world. Understanding fragmentation behaviour of rock under crushing process is fundamental to improved productivity and efficiency in mining operations. This is particularly so as all subsequent size reduction processes such as crushing and grinding are far more energy intensive than the initial blasting process employed in breaking of in situ rock. A considerable body of experimental studies exists on the behaviour of rock crushers for specific rock types in order to aid in the design of various types of crushers. However, these studies are mainly site specific, that is, the results are largely empirical, and the fundamentals of fracture process that lead to size reduction have not been dealt with adequately. Most such studies have attempted to link the input parameters, such as feed size and crusher parameters, with output particle size, and global energy expended in the process. However the physical mechanism of crushing process is still not well understood. First of all, the energy consumed by the rock sample is hard to calculate during standard crushing or grinding tests; secondly, multi-particle test is hard to perform in the laboratory due to irregular shape of the subject rock sample. In This paper, describes a laboratory crushing apparatus for multi-particle rock samples, with sufficient control of the energy expended in the process, with a view to relate creation of new fracture surfaces in the size reduction process."

Jan 1, 2015

By R. Noorani, M. Cai

"Excavation of deep underground openings in highly stressed grounds can generate new fractures near the openings. As a result, rock mass bulking may occur, leading to large wall deformation. A better understanding of brittle rock failure and the associated fracturing process at the laboratory scale is an essential step towards evaluating dilation behavior of rocks. A grain-based model that can capture dilation behavior of rocks under various loading conditions at the laboratory scale can be a useful approach to study rock mass bulking at the field scale. The aim of the paper is to study the dilation behavior of rocks at the laboratory scale employing numerical simulation. A modified grain-based model is used to simulate the macroscopic response of crystalline rocks by considering micro-fractures at the grain scale. Grains generated with the Voronoi tessellation are allowed to fail in tension or in shear using a strain-softening model. Damage is represented by either grain boundary fracture or grain failure, or the combination of the two. As stress increases, the process of damage, fracture initiation and coalescence in rocks can be captured.The grain-based model was calibrated using test data of the Lac du Bonnet granite and a parametric study was conducted. Numerical simulation results showed that the proposed modeling approach is able to capture most of the mechanical properties, fracture pattern, and dilation behavior in both unconfined and confined loading conditions. In an unconfined compression test, interactions of microscopic fractures may lead to macroscopic shear or axial splitting failure depending on the chosen micromechanical parameters. Numerical experimental results show that the dilation behavior of the model is strongly related to the failure mechanism of rocks. Tensile-failure-dominated failure mode generates large dilation due to the formation of new cracks that are sub-parallel to the loading direction. On the other hand, shear-failure-dominated failure mode produces small volume increase. One significant finding from this study is that in order to capture large dilation using grain-based UDEC models, intragranular grain failure should be considered."

Jan 1, 2015