Search Documents

By G. Knight

"Results of a program of dust research carried out at the Mines Branch Laboratory, Elliot Lake, indicate that dust-concentration estimates vary greatly, depending on the sampling instrument, the assessment technique and the properties of the dust cloud. The wide range of the ratio between the estimates by any pair of instruments shows that the correlation between the health hazard and dust-concentration estimates by most existing sampling instruments must be questionable. Important studies are being carried out to permit the definition of mine environments in more precise technical terms. The influence of size selection, the physical property measured, composition and sampling period on the assessment of the health hazard are discussed."

Jan 1, 1969

By S. Malopheyev, I. Vysotskiy, R. Kaibyshev, S. Mironov

"In this work, the effect of pre-strain rolling on the annealing behavior of friction-stir welded 6061-T6 aluminum alloy was studied. To this end, the as-welded material was rolled to 10 or 20 pct. of thickness reduction prior to the standard post-weld T6 heat treatment. Three rolling directions were the 3-mm thick sheet were considered: along the welding direction, perpendicular to the welding direction, and at the angle of 45° to the welding direction. At relatively low pre-strains (10 pct.), the annealing behavior was found to be very sensitive to the rolling path, and rolling along the welding direction was most effective in suppressing abnormal grain growth. On the other hand, increasing the pre-strains to 20 pct. of thickness reduction inhibited abnormal grain growth irrespective of the rolling path.INTRODUCTION Heat-treatable wrought Al-Mg-Si alloys are widely used due to attractive combination of strength, ductility, excellent corrosion resistance and low cost (Polmear, 2006). To provide the optimal balance of mechanical properties, these materials are typically commercially available in appropriately work- and precipitation-hardened conditions (Polmear, 2006). During conventional fusion welding, however, the prior strengthening effect is totally lost due to elimination of the work hardened structure and dissolution of the strengthening precipitations. An innovative friction-stir welding (FSW) technology may partially overcome this problem. Due to the solid-state character of this process, which involves very large strains, the welded material is characterized by fine-grained microstructure with moderate-to-high dislocation density, and thus the prior work hardening effect may be preserved or even enhanced (Threadgill et al., 2009; Mishra & Ma, 2005). However, heat input associated with FSW inevitably leads to dissolution and/or coarsening of strengthening precipitates, thus giving rise to the undesirable material softening. In an attempt to restore the strength of the friction-stir welded material, the standard T6 post-weld heat treatment has been applied, but this approach was found to lead to abnormal grain growth (Malopheyev et al., 2016; Mironov, 2013, Mironov et al., 2015)."

Jan 1, 2018

By S. Abu-Samra

By virtue of its complex nature, the construction industry comprises a wide spectrum of interrelated variables and factors. This multifaceted character of the construction industry puts the use of engineering modeling tools and techniques on top of project management necessities. This research introduces a macro-level earthmoving management system using Genetic Algorithms (GAs) to reach the optimum allocation of earthmoving equipment. The Earthmoving Equipment Management System (EEMS) functions through four integrated modules: (1) A Central Database containing information about projects and available equipment; (2) An Equipment per Segment Selection module that calculates the cut and fill quantities, plots the Mass Haul Diagrams, and selects the equipment types to be used for each segment; (3) An Equipment Pool module which determines the production and cost for each available equipment, based upon the project site conditions; and (4) An Optimization Engine equipped with a GA optimization solver. This engine formulates the optimum earthmoving cost for all projects, by changing the number of allocated equipment. The Optimization Engine takes into account the number of available equipment and calculates the weekly equipment allocation. The EEMS model was implemented on an earthmoving company conducting five different projects on hand. The model proved to be an effective tool in providing decision makers with optimum equipment utilization on a multi-project scale to minimize the earthmoving cost. The results were then compared with the company?s existing micro-level management system, demonstrating better performance on the level of savings, amounting to 13% of total earthmoving cost.

Aug 1, 2013

By S Sokhanvaran

Electrodeposition of silicon from a cryolite based electrolyte at a relatively low temperature (1000°C) is a promising approach to generate high purity silicon. In order to obtain fundamental data pertaining to electrowinning of silicon from Cryolite?SiO2 melts, density and electrical conductivity measurements were made. A range of temperatures and SiO2 contents was studied for each property. It was found that while density has an inverse relationship with temperature, the dependence for electrical conductivity is direct. Increasing silica content up to the saturation limit (~ 5 wt%) increases the density whereas further increase in SiO2, lowers the melt density. On the other hand, the conductivity is lower for the melts with greater SiO2 content, at any temperature.

Jan 1, 2011

By C. Gravel, A. Fathi, P. Rivard, G. Ballivy, Z. Moradian, M. Quirion

Knowing shear mechanism of discontinuities under monotonic and cyclic loading conditions is a key factor in stability analysis of rock slopes and rock foundations. In this paper, the effect of cyclic loads on the shear mechanism of joint asperities is described. For this purpose, a fresh tension-split joint from a granite block was used as a reference and thirty five mortar replicas were fabricated. Cyclic shear tests were conducted on replicas under low values of constant normal load (CNL) using a servo-controlled loading system. Tests were performed in two consecutive steps; load-controlled and then displacementcontrolled. In the load controlled part, after initial increase of shear stress to 0.25 MPa, the test was stopped for 2 minutes, then increased to 0.5 MPa, and finally decreased to 0.25 MPa. This process was repeated ten times. At the end, the test was continued up to 10 mm shear displacement under displacement-controlled loading in order to pass the peak shear strength and reach the residual strength. Characterizing joint surface and modeling of involved asperities during the tests was undertaken using a Matlab code developed with new mathematical expressions. The algorithm used in the code is based on three-dimensional coordinates of the scanned joints’ surfaces before and after the test. It was found that a high percentage of degradation happens during the first cycle of loading and during the other cycles, degradation occurs gradually. While comparing tests conducted in monotonic and cyclic loading conditions, it was observed that under low number of cycles, the pronounced mechanism is consolidation of the joint surfaces. This consolidation increases contact areas and, therefore, shear strength parameters.

Jan 1, 2015

By G. Zárate, G. Tapia

Anglo American Chile has been doing copper concentrate leaching studies at the laboratory and small pilot plant scale since 1992. Among the processes evaluated are bacterial leaching and pressure leaching using Mantos Blancos, Salobo Project and Quellaveco Project concentrates. Late in the nineties, it was decided to focus the research on pressure leaching, either medium or total pressure oxidation. Preliminary scouting tests were run with Mantos Blancos concentrate samples during 2000, which were repeated during 2003 together with samples of Los Bronces and El Soldado concentrates, in order to define the most suitable concentrate for running a pilot plant campaign at AARL, which was carried out in two campaigns, a first one from November 2003 through January 2004 and a second one during April 2004. Mantos Blancos was the selected concentrate and the laboratory and pilot plant results are discussed in this paper together with some preliminary economic estimates.

Jan 1, 2004

By E. J. Marcotte

"INCO LIMITED'S Shebandowan Mine and Mill is located in a scenic tourist and cottage area near the western tip of Lower Shebandowan Lake, approximately 90 Km west of Thunder Bay, Ontario. This nicely designed complex is a positive indication that mining operations can co-exist in harmony within the natural environment.The Shebandowan complex processed nickel-copper ore from 1973 to 1985, inclusive, after which operations were shut down.In late 1988, INCO LIMITED decided to place the Shebandowan complex back into operation, under contract, to mine and mill the remainder of the ore body, according to their specifications. MaclSAAC'S EXPLORATIONS was the successful bidder for the project. Following preliminary rehabilitation, operations were re-activated in late March, 1989. The ore mined to date is of a moderately lower nickel grade than the majority of previous years. However, a higher tonnage rate, combined with improved nickel recoveries, has contributed to a viable operation.A series of mill operating and equipment modifications has enabled MaclSAAC EXPLORATIONS to achieve the quality and grade of nickel-copper concentrates specified, and at the same time, expand mill tonnage throughput while attaining increased nickel recovenes."

Jan 1, 1992

By F. Khomamizadeh

In this study, deep cryogenic treatment was applied to A319 cast aluminum samples. Although the cryogenic treatment didn't have any significant effect on mechanical properties of the well degassed and fluxed samples, but the tensile strength of the samples containing a considerable amount of gas and shrinkage defects was improved surprisingly, This improvement was attributed to the strengthening of the a-aluminum matrix which slows down the propagation of the existing defects. There was no significant increase in the hardness after cryogenic treatment, The abrasion resistance of the alloy was improved after cryogenic treatment, by developing a homogeneous protector shield, composed of abrasive grains penetrated into the soft aluminum matrix and kept tight.

Jan 1, 2005

By R. W. Lawrence, O. Lopez

Many gold deposits in the world have not been developed clue to the presence of copper and other base metals which can cause metallurgical and environmental challenges clue to the formation of base metal cyanide complexes. SART technology (sulphidization-acidification-recycle-thickening) can resolve these issues by recovering copper as a high grade sulphide concentrate, recycling the associated cyanide back to the gold leach, and eliminating the downstream environmental liabilities. Project economics can be improved substantially, leading to a positive re-evaluation of new and existing gold-copper projects. Some aspects of the design and operation of two recently commissioned SART plants will be discussed.

Jan 1, 2011

By M. Maley, S. Burling, R. Ring

ABSTRACT The numerous global uranium deposits vary significantly in mineralogy, grade, and textural characteristics; therefore, information from traditional (or conventional) sources on the fundamentals of leaching uranium and gangue minerals is not always applicable when studying particular ores. Empirical studies can be effective in understanding leach systems and can lead to improvements in process design but there remains a lack of fundamental understanding necessary for ongoing process optimization as ore bodies continue to vary. ANSTO Minerals has undertaken a work program to address several fundamental questions about uranium leaching, including the unexpected impact for some ore types of leaching at high oxidation potential.

Jan 1, 2012

By Rodrigo Serna, Nora Schreithofer, Zoltan Javor, Kari Heiskanen

"Mineral floatability is a function of mineral properties such as size, liberation, shape, surface composition, reagent coverage on the surface, level of oxidation on the surface, etc.; pulp chemistry: Eh, pH, temperature, DO, reagent type, etc. and hydrodynamic conditions: turbulence, gas dispersion, D32, etc. The biggest challenge with predicting the floatability of an ore is finding a measurement method that would take into account the effect of all of the variables on the floatability of the minerals. The particle-bubble attachment time measurement is considered as an alternative way to predict the floatability of minerals instead of using expensive and time consuming flotation tests because it takes into considerations both surface chemistry and hydrodynamic parameters present in the froth flotation. The existing particle-bubble attachment time method is suitable for studying some significant flotation variables such as pH, temperature, particle size, reagent type and concentration. Nevertheless, measuring the attachment time as a function of collector coverage or surface oxidation is much more challenging. This paper introduces a new induction timer designed to measure the effect of galvanic interaction on the attachment time of particles. The new setup employs an array of needles to create 6 bubbles with the average size of 2.1 mm. Imaging system is used to set the initial distance between the particle bed and the array of bubbles. The attached particles are collected and sent for further analysis. One of the main benefits of the new experimental setup is that the attached particles can be physically separated from the unattached particles therefore many of the particle properties can be analysed and evaluated.INTRODUCTIONSchumann (1942), and Tomlinson and Fleming (1963) proposed that the flotation rate constant is dependent on four probabilities: particle-bubble collision (PC), particle-bubble attachment (PA), particlebubble aggregate stability in turbulent environment (PE), and particle-bubble aggregate stability in froth phase (PF). Any change in any of these probabilities will affect the overall flotation rate constant. All of the above-introduced probabilities are influenced by stream- variables and mechanical variables but their extent of influence vary. The stream variables are particle properties that have been shown to affect flotation rate constant such as size, shape, liberation, mineralogical composition, reagent surface coverage, surface oxidation, etc. The mechanical variables are the direct and indirect properties of the flotation unit affecting flotation rate constant such as cell and impeller geometry, air rate, impeller speed, air holdup, bubble size, residence time, hydrodynamics, froth depth, etc. For instance, the probability of collision is affected by many mechanical variables (bubble size, hydrodynamics, bubbles holdup etc.) but only one stream variable (particle size) has a major effect on it. On the other hand the probability of attachment is affected by much more stream variables: particle size, shape, liberation, surface composition, particle surface oxidation and collector coverage, Eh, pH, etc."

Jan 1, 2016

By Atsushi Sainoki

Blast vibration induced by mining activities, such as stope production blasts, could lead to the initiation of seismic events that inflict damage to mine openings. In this paper, the effect of stope production blasts on nearby fault is examined. First, validation of blast vibration attenuation is performed with a numerical model representing a single blast hole through comparison with that calculated from charge-weight scaling law derived from in-situ data. Subsequently, a mine-wide scale model with a fault parallel to a steeply dipping, tabular ore deposit that is mined out with sublevel stoping method is generated, and the stopes are extracted and backfilled with static analysis to simulate burst-prone conditions on the fault. Based on the stress states, dynamic analysis is performed, in which blast vibration is applied to grid points on a stope wall on the hanging wall side. This assumes 9 blast holes located close to the wall, and blast-induced particle velocities that consider the positional relationships between the assumed blast holes and the stope wall are applied. During the dynamic analysis, blast sequence is considered, and stress states and shear displacement on the faults are examined. It is found from results that, after a rise in normal stress on the fault due to compressive waves induced by the blasts, the normal stress decreases because of the reflection of the compressive waves on the fault. The reduction in the normal stress due to the reflected waves is found to be large enough to cause the fault to slip. The results also show that the level of normal stress eventually keeps decreasing with time as the blast sequence proceeds and that an increase in shear displacement on the fault is accompanied by a decrease in normal stress. This study clarifies the mechanism by which blast vibration causes the fault to slip. In addition, the simulation technique to apply blast vibration that takes into account blast sequence and the locations of blast holes to a stope wall is developed.

Aug 1, 2013

By D. Lemieux

A gold bearing pyrite concentrate was treated at the pilot scale for the extraction of gold. Mineralogical analysis of the concentrate identified gold to be mainly present in the form of a solid solution in pyrite. This gold distribution resulted in a poor extraction yield of 55% by direct cyanidation. A piloting campaign including an oxidative pre-treatment by roasting in a fluid bed was followed by treatment with halogens for gold extraction has led to a gold extraction yield of 96.5%. Sulphur removal during the oxidation was very efficient at >99.5% and gold extraction by the halogens was completed within a 1 hour contact time. The piloting was performed on a 300 kg sample and uses a diluted solution of hypohalites as the oxidizing agent for gold extraction. Sulphuric acid was injected in the reactor during the halogens treatment to lower pH to 2. The diluted solution of hypohalites (1-3%) was generated by electrolysis during the piloting campaign in a membrane-less electrolysis cell. The extracted gold was recovered over activated carbon in column and the gold depleted brine was treated for impurities removal and recycled for further gold extraction. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable, the Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.

Aug 1, 2013

By L. Li

Backfill is increasingly used in underground mines, as it can help reduce the environmental impact from mining operations. However, the primary objective of backfilling is to provide safe working space for miners, by improving ground stability conditions. As cement is often added to the backfill, a critical issue is the determination of the required backfill strength (cohesion) due to the binder. This value is usually obtained from a solution proposed by Mitchell and co-workers, in the early 1980?s, for stopes with an exposed backfill face. This paper presents a brief review of the Mitchell et al. solution, with some of its main limitations. Some of the recently developed solutions for backfill design are then summarized and discussed.

Aug 1, 2013

By J. P. Piguet, A. Hosni, J. P. Josien, H. Baroudi, R. Hadadou

"The iron ore mines in the Lorraine region of north-eastern France cover a surface area of approximately 3,900 km2 and involve more than 150 cities. A total extraction method was usually used during exploitation, but this technique was sometimes replaced by the room and abandoned pillar technique when it was necessary to protect surface buildings and infrastructure. Rooms and abandoned pillars were initially designed to ensure long-term mine stability. However, this aim was not always reached and numerous collapses occurred in the Lorraine iron basin, either during production or several years after closure. Several subsidence events were identified during a period of one century; the most recent event occurred in 2012. Two groups of events were identified. The first group represents events characterized by sudden surface movement, and the second group includes event characterized by progressive subsidence.Numerous studies conducted during the last decade helped improve our understanding the origin mechanism of spontaneous or progressive (slow) events. These studies led to identifying long-term potentially unstable underground zones (hazard zones), particularly deep zones located under buildings and infrastructure. The latest are currently monitored by microseismic networks. A similar high requirement level is needed for unstable zones without taking into account the kinetics of the subsidence, which is very important for safety. Thus, GEODERIS initiated this study, primarily to acquire a better understanding of the kinetics of the progressive events group and identify the main parameters that could explain why some pillars zones developed a maximum amplitude subsidence on surface within a few hours or days, while it took several weeks to months for others. In practice, the results of this study will facilitate adapting the requirement level of microseismic monitoring system to the kinetics of pillar collapse.To retrieve the real kinetics for each event, historical and sparse documentation was used. Firstly, archives research was conducted, especially testimonies and newspaper articles published during the events. This work helped to gather useful information that sometimes contained a precise description of subsidence duration. The archives research helped to classify some progressive events according to the subsidence kinetics. Secondly, a diagnostic of geotechnical and geomechanical parameters of historic events was realized, combined with a cross analysis of the data. The analysis took into account dimensions of underground workings (e.g., pillar lengths, widths, heights, introduction of a “pillar shape factor”, and stress amount). An original expression was highlighted to connect the pillar geometry to the stress state. The kinetics expression was calibrated to classify the historic events taken into account according to the kinetics of movements. The kinetic criterion was applied to predict subsidence kinetics for the potential unstable zones currently monitored by a microseismic system."

Jan 1, 2015

By Fabio Terzi

In this investigation some preliminary results are reported about the electrochemical oxidation of CO using goldbased encapsulated nanoparticles grafted on conducting substrate. The investigation has been planned in four steps: 1. production of Au(111) substrate and modification with self assembled monolayers; 2. synthesis and embedding of nanoparticles; 3. grafting of encapsulated nanoparticles on electrode substrates; 4. investigation of CO electroxidation on the modified electrode. The systems were characterized by means of various techniques (spectroscopic, microscopic, and electrochemical methods), obtaining information about SAM's structure and morphology, size and composition of nanoparticles and electrochemical behavior of modified electrodes.

Oct 1, 2003

By D. P. Bishop, G. J. Kipouros, R. L. Hexemer Jr., I. W. Donaldson, W. F. Caley

Aluminum powder metallurgy (APM) is an advanced metal forming technology frequently employed to fabricate complex structural components in a near-net-shape fashion. Exhibiting nearly 100% material utilization, APM continues to rise in popularity. Recent research initiatives in this field have emphasized the development and processing of advanced 2xxx and 7xxx series alloys. In particular, APM equivalents to wrought 7075 and 2024 have been sought. An overview of work completed in this area is presented. Included are data on the various production stages (powder compaction, sintering, forging, and heat treatment) as well as the microstructure and mechanical properties of the finished products.

Jan 1, 2010

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, D. K. Fountain

"Abstract -A test survey using the MEGATEMII airborne electromagnetic system was flown over the Iso and New Insco massive sulfide orebodies in the Rouyn-Noranda mining camp, Canada. The results were compared with data from historical systems (INPUT, DIGHEM) used to discover the deposits. The historical data show that the two deposits have comparable conductances. However, the modern MEGATEMII system reveals that the New Insco deposit has a much slower decay than the Iso deposit, and it is, therefore, interpreted to be more conductive. The MEGATEMII anomaly maps provide estimates of the location, depth, dip, and strike of the two deposits, information that was not available from the historical anomaly maps. The signal-to-noise ratio of the MEGATEMII data is greater than the historical data, yielding more sharply defined anomalies. The investigations also included a comparison between 90 Hz and 30 Hz MEGATEMII data. The 90 Hz data were found to be useful for mapping the less conductive parts of the Iso body, whereas the 30 Hz data demonstrated that the New Insco body is more conductive. Analysis of height attenuation data over the Iso body indicates that the body could be seen by the MEGATEMII system if it were buried an additional 230 m deeper (in highly resistive material). On the other hand, the INPUT system would detect the Iso body only if it were buried no deeper than an additional 60 m. Tests with the transmitter turned off showed that, for this flight, the MEGATEMII system noise levels on the processed data are about 300 pT/s. Sommaire - Dans le cadre d’un projet de recherche, un ensemble de levés d’essais électromagnétiques aéroportés employant le système de MEGATEMII a été effectué au dessus des dépôts d’Iso et de New Insco, Rouyn-Noranda, Canada. Les données ont été comparées avec les réponses des systèmes qui ont découvert ces deux dépôts (INPUT et DIGHEM). Les données antérieures montrent que le dépôt d’Iso a une conductance comparable à celle de New Insco. Cependant, les données de MEGATEMII démontrent que le dépôt de New Insco a une haute valeur de la constante de décroissance, ce qui reflète une plus forte conductivité. La carte d’anomalies de MEGATEMII indique la localisation, la profondeur, le pendage et l’orientation des deux dépôts, ce que la carte d’anomalies antérieure ne montrait pas. Le rapport de signal à bruit de MEGATEMII est plus grand que celui des données de INPUT et de DIGHEM; de plus, les pics sont mieux définis. Les tests ont également permis une comparaison entre les fréquences de base de 90 Hz et de 30 Hz. Les données de 90 Hz se sont montrées utiles pour cartographier la partie du dépôt Iso dont la conductivité est la plus faible, tandis que les données de 30 Hz montrent clairement que le dépôt de New Insco est plus conducteur. Les analyses de l’atténuation du signal avec la hauteur ont indiqué que le dépôt d’Iso pourrait être détecté par le système MEGATEMII s’il était enfoui à 230 m sous la surface (dans un milieu hautement résistant). D’autre part, le système INPUT pourrait seulement détecter le dépôt d’Iso s’l était situé à 60 m de profondeur. Les tests avec l’émetteur fermé démontrent que le niveau de bruit est des l’ordre de ±300 pT/s."

Jan 1, 2006

By E. J. Schwarz, A. A. Winir

"Absolute magnetite contents were determined for asbestos specimens in various stages of milling by using a Faraday-type thermomagnetic balance. Comparison of these results with magnetic ratings (MR) supplied by the mining companies cooperating in this study reveals strong scatter. The main cause of this scatter is thought to be that the MR values were obtained in magnetic fields well below the saturating field of magnetite (5,000 oe). However, only the saturation moment is an intrinsic property and consequently must be used for the purpose of obtaining reliable estimates of the magnetite content. Curie points indicate that virtually pure magnetite and possibly Ni3Fe is present in all samples, and another phase, probably (Cr, Al) magnetite, is present in a few samples. The susceptibility in fields stronger than 5,000 oe is positive and falls in the normal paramagnetic range, whereas sy nthetic chrysotile exhibits weak diamagnetism. This suggests that, as a general rule, the least adulterated natural chrysotile concurs with the samples showing the smallest positive susceptibility above 5,000 oe. The magnetite appears to increase in quantity with a decrease in fibre length and to be somewhat more uniform in distribution for samples showing substantial fiberization (opening of the fibres)."

Jan 1, 1971

By B. Rivard, D. Francis

A layered Archean magma chamber is exposed at the base of the Yasinski segment of the La Grande greenstone belt. This intrusive complex lies beneath a sequence of mafic volcanics and is underlain by granitoid basement which is crosscut by a swarm of gabbroic dykes. The gabbros of both this complex and the dyke swarm of gabbroic dykes. The gabbros of both this complex and the dyke swarm define a pronounced Fe-enrichment trend. The volcanic patterns of the La Grande and Eas tmain greens tone belts, however, define a series of iron depletion trends which originate in the iron enrichment trend of the gabbroic intrusives. These patterns suggest that the gabbros produced in the intrusive complex may serve as parental liquids for some of the lava suites of the James Bay greens tone belts.

Jan 1, 1984