Search Documents

By Z. Trojanová

Mg micropowders generated by gas atomisation of a magnesium melt with argon were mixed and ball milled with ceramic nanoparticles prepared by laser-induced gas phase reaction. The materials were then hot extruded. Specimens were deformed in tensile as well as compression tests at temperatures between 20 and 300 °C at a constant initial strain rate. The flow stress is significantly influenced by the test temperature. The yield stress decreases with temperature. This decrease and the flat character of the stressstrain curves at elevated temperatures indicate possible contributions of softening processes. The materials studied exhibit high-damping characteristics. The results are analysed and possible mechanisms are discussed.

Jan 1, 2006

By J. Muralha, L. Lamas

"Given the results of triaixial tests, regressions are commonly used to evaluate the parameters of failure criteria that model intact rock strength and to perform statistical inferences used to evaluate characteristic values defined in EC7. Statistical robustness of these inferences is affected if the basic hypothesis underlying regression are not met, namely homoscedasticity (constant variance of the errors). This paper presents analyses of 23 sets of triaxial tests, starting by the evaluation of the regression parameters of the Mohr-Coulomb linear criterion and of the Hoek-Brown non-linear criterion, followed by carrying several statistical tests to check the homoscedasticity null hypothesis of independence between the variance of intact rock strength and the confining stress.INTRODUCTIONThough rock engineering design is clearly included in the scope of Eurocode 7(EN1997-1), its implementation raised a wide discussion regarding the applicability of structural safety concepts to geotechnical design of construction works in or on rock masses. The basis of the limit state design philosophy adopted in EC7 is that, for each particular design situation, all the possible limit states for a structure, or part of it, shall be considered and that it shall be demonstrated that the likelihood of any limit state being exceeded is sufficiently small. Though EC7 allows the limit states to be verified by one or a combination of methods, use of calculations is by far the most used, and it is often confused with the EC7 itself. It involves using characteristic values of actions, ground properties and geometrical data, as well as obtaining their design values by the partial factor method.Characteristic value of a given material property is defined in Eurocode (EN 1990) as: “value of a material or product property having a prescribed probability of not being attained in a hypothetical unlimited test series. This value generally corresponds to a specified fractile of the assumed statistical distribution of the particular property of the material or product”. As regards the design value of a material or product property, according to the Eurocode it is a “value obtained by dividing the characteristic value by a partial factor”."

Jan 1, 2015

By J. Pepin

When using alternating current submerged arc welding (SAW) to produce pipes from microalloyed linepipe steels, it is critical to balance penetration depth and deposition rates, in order to minimize the number of weld passes while still maintaining good heat affected zone (HAZ) microstructures and properties. A series of bead-on-plate (BOP) submerged arc welds were performed on X70 steel, using different waveform variable settings (i.e., balance, offset and frequency). Weld bead cross-section profile deposition and penetration areas were measured, and both Vickers hardness and Charpy V-notch impact testing were performed. Both single electrode and tandem electrode welds were evaluated.

Jan 1, 2011

By L. Bichler

Lightweight magnesium alloys are gaining in popularity for applications in the automotive and aerospace industries, Their use, however, remains limited due to their relatively low strength and creep properties. Lost Foam Casting (LFC) is a new casting process and the strength of foam cast magnesium alloys has not been investigated in great detail thus far, In this research, magnesium alloy AZ91 E and three new alloys were cast by the LFC process to study the effect of varying aluminum and manganese content on the alloy's tensile properties, The study reveals, that the tensile strength of the magnesium alloy is closely related to the relative amount of aluminum in the system. Formation of ß-Mg17Al12 phase was seen to significantly affect the yield strength and ductility of the alloy, Furthermore, formation of manganese intermetallic compounds was seen to effectively increase yield strength of the base alloy, Individual alloy morphologies were analyzed via optical and SEM techniques.

Jan 1, 2004

By F. Bosché

Previous research has shown that ?Scan-vs-BIM? systems are powerful to provide valuable information for tracking structural works (progress, quality, safety). However, the transferability of this capability to other construction areas such as MEP works has not been assessed so far. Comparatively, the construction of MEP systems, in particular pipes and ducts, tends to be more flexible with respect to the positioning of individual components, so that Scan-vs-BIM systems could be defeated when tracking MEP installation works. This paper presents recent results on the feasibility and performance of using a Scan-vs- BIM system to track MEP works. The approach followed is presented and then tested with two real-life challenging case studies were conducted simultaneously but totally independently in Canada and Italy. The results show that, as expected, pipes and ducts tend to be more loosely positioned than structural elements leading to a poorer performance of the Scan-vs-BIM system. Nonetheless, it appears that the system works well to assess the level of conformance of site installation works, providing valuable information for estimating emerging performance metrics like ?percent built as-designed?. In addition, the proposed system could also be useful to accelerate and thus reduce the cost of delivering as-built BIM models for in the case of new builds.

Aug 1, 2013

By E. S. Moore

DEEP oxidation and-secondary enrichment of ore deposits, although so important in many parts of the world, are comparatively rare in the Canadian shield. Intensive glaciation during the Pleistocene epoch accounts for their rarity. Glaciation has cost Canada much in the destruction of not only enriched ore deposits, but placers that must have been developed near our numerous gold deposits during the long period of weathering that pre-ceded the Pleistocene. There seems to be a very common misconception regarding the average depth of rock that has been removed from the shield by glaciers. These bodies of ice are usually given credit for the removal of the greater portion of the thousands of feet of rock that we know has been eroded from this large area since Precambrian time. As a matter of fact, the average thickness of solid rock removed can be measured in tens rather than even hundreds of feet, although very deep erosion has resulted in some sections where the glacial ice has been constricted in depressions, such as deep valleys and lake basins. On the other hand, there are few areas within the shield where the glaciers have not disturbed practically all of the mantle rock and some feet of the underlying bed-rock. The chances of finding deeply oxidized cappings and enriched ore deposits are therefore comparatively few and these have been found chiefly where favourable structural and topographic conditions for their formation and preservation have existed. Faulting has been responsible for several of these deposits, and easily decomposed rocks, such as. sulphides and carbonates, have been very important factors. Topographic features, such as high and resistant hills, favourably situated with respect to the ore deposits have, in a few cases, played a part in providing protection from glacial erosion and in furnishing head for the descent of surface waters. At least four cases of oxidation to depths quite abnormal in the Canadian shield have so far been found in Ontario. These are the Helen and Josephine iron mines in the Michipicoten district, the Keeley silver mine in South Lor-rain, and the Ross gold mine in Hislop township, Cochrane district. A deeply oxidized zinc deposit of unusual interest occurs in the Precambrian rocks in New York State, not far from the Canadian border, and there arc the well-known iron deposits in the Lake Superior region of the United States.

Jan 1, 1938

By J. A. Allan

OCCURRENCES of salt in Alberta have been mentioned and described by the writer in 1929 (l) and by Cole in 1930 (2). Brine springs occur at a number of places along the valley of Athabaska river north of latitude 56 degrees, and also on the south margin of Salt prairie, twenty-five miles west of Fitzgerald in the vicinity of the 60th parallel of latitude, which is the boundary between Alberta and the Northwest Territories. These salt springs were visited by Sir James Richardson in 1820, and in the same year D. W. Harmon stated that " ... clown Salt river there are several places where almost any quantity of excellent dean white salt may be taken with as much ease as sand along the seashore" (3). One hundred years later, in 1920, when the writer first visited these springs, the "dean white salt" which had accumulated about the springs was about 400 tons ( 4). This paper deals with a thick deposit of rock-salt which has been proved by drilling in the vicinity of McMurray. Particular attention will be given to a well drilled at Waterways early in 1936 by Industrial Minerals, Limited, when a continuous bed of rock-salt was penetrated with a thickness of 199 feet. As this paper is being presented, a salt plant is being completed and a production well is being drilled at the plant. < is salt deposit is in the vicinity of McMurray, close to the junction of the Clearwater and Athabaska rivets, in township 89, range 9, west of the 4th meridian. McMurray is about 240 miles northeast from Edmonton. As shown on Figure 1, Clearwater river, which rises at Methy portage, in Saskatchewan, enters Athabaska river at McMurray. Some three miles above the mouth of Clearwater river, the Hangingstone enters from the southwest. Waterways, where the latest salt development has taken place, is situated at the end of the Northern Alberta railway, a distance of 304 miles from Edmonton. This railway reaches the bottom of the Clearwater valley at Draper station, about 3 miles east of Waterways and near the mouth of Deep creek. The Draper bituminous sand plant is approximately half a mile east of Draper station. About one mile south of the townsite of McMurray, Horse river enters the Athabaska from the east.

Jan 1, 1937

By S. Perez

Core drilling is a fundamental process in the mineral exploration industry. As deep exploration in hard rocks is accelerated due to the depletion of near ground mineral resources, deep-drilling operations need to reduce their reliance in operators experience and begin to implement new technologies in order to increase efficiency and cost-effectiveness of the overall process. Currently, lack of real-time information on the bit/rock interaction is a major problem. Therefore the mechanism behind the acoustic emission, which is a proven technique for remote monitoring, generation in mechanical rock cutting must be understood in order to provide real time information about the rock. This paper aims to identify the influence of mineral composition of granitic rocks on the acoustic emission (AE) during rock abrasivity test with a single contact tool and to evaluate the feasibility of AE as a means to infer Cerchar Abrasivity Index (CAI). Single contact tool will provide precise and accurate description of the source of AE. To provide constant grooving speed Cerchar apparatus was modified to monitor AE during rock/tool interaction. Tests on the modified Cerchar apparatus are carried out under the static load of 70N and cutting speed of 1 mm/s. A Scanning Electron Microscope (SEM) is utilized to visualize the groove in the rock and to identify the mineral composition through Back-Scattered Electrons (BSE) reflected from the rock sample. Based on the microscope images, it was found that biotite shows a larger groove area and plate-like fractures accompanied with burst-type AE signal, whereas plagioclase and quartz, which are characterized by similar hardness and BSE brightness, possess shattered-like fractures and more continuous-type AE signals. In addition, a-value of the Gutenberg-Richter scale has been found to well correlate with Cerchar Abrasivity Index (CAI).

Jan 1, 2015

By D. H. Ryan, B. Abdul, M. Pernechele, E. Asselin

Hydrometallurgical processing of sulphide concentrates at medium temperature (150°C) produces residues, which contain valuable metals (Cu, Ni) as well as sulphur and iron bearing minerals and phases. The low solubility of iron during the medium temperature processing of sulphide ores can favour the formation of poorly crystalline, nano-scale iron oxide/oxyhydroxide phases. A better understanding of the formation and structure of these iron precipitates may elucidate key factors that would ultimately result in lower valuable metal losses and more stable leach residues. Residues from two medium temperature leach processes were characterized by Mössbauer Spectroscopy. Some portions of the Mössbauer Spectrum were suspected to be linked to jarosite but could not be positively identified as such. There was a broad range of disorder and substitution present in the material and solely attributing it to jarosite proved difficult. Various synthetic jarosites with Cu substitution were precipitated for Mössbauer analysis. These were then characterized by Quantitative X-Ray Diffraction (QXRD), Scanning Electron Microscopy (SEM), Inductively Coupled Plasma Mass Spectroscopy (ICP-MS) and Mössbauer Spectroscopy. The Mössbauer Spectra of the synthetic jarosites is compared with that of the residues from medium temperature (150°C) sulphide concentrate leaching.

Jan 1, 2014

By D. K. Sarkar, J. Perron, J. D. Brassard

"Nearly perfect spherical shaped water drops rolling-off from the surface of lotus leaf is one of the beauties of nature. This kind of surface is called superhydrophobic, since the water does not like it. Physically, a superhydrophobic surface provides a contact angle (CA) of water over 150°. The combinations of both mico-nanostructure topography as well as low surface energy are essential to have such high CA on a surface. Nano-micro structured superhydrophobic surfaces have been developed in different methods. (i) Monodispersed fluorinated silica nanoparticles have been synthetized via Stöber Sol-Gel process and deposited on various surfaces, such as aluminium or glass, to obtain transparent superhydrophobic thin films. (ii) Similarly, zinc stearate nanocomposite coating has been fabricated by spray process on the same substrates. These thin films are found mechanically robust with drag reduction of coefficient 16% lower than as-received surfaces. (iii) By electrodepositing pure zinc on steel surfaces and further coating it with diluted room-temperature vulcanized silicone rubber, the surface become superhydrophobic. This superhydrophobic surface protects the steel against corrosion by increasing the polarization resistance from 1.5 k? on steel to 44.4 k?. This coating also reduced the ice adhesion on the steel surface 6.3 times as compared to bare steel substrates. Globally, these superhydrophobic surfaces have tremendous applications against corrosion reductions, drag reductions and ice adhesion reductions.INTRODUCTIONSuperhydrophobic coatings are increasingly attractive to the industry and academia due to their unique self-cleaning properties as a result of their water repelling characteristics. Fabrication of superhydrophobic coating is an inspiration from nature as water is seen to repel on many natural surfaces such as those of the lotus leaves, butterfly wings, water striders’ legs, and so on (Gao & Jiang, 2004; J. Huang, Wang & Wang, 2006; Neinhuis & Barthlott, 1997; Zheng, Gao & Jiang, 2007). This non-wetting phenomenon is well understood on lotus leaves, shown on the Figure 1 (a), and it is considered as the basis of the studies of superhydrophobicity. The existence of this binary structure on the surface of the lotus leaves allows a large amount of air entrapment and consequently reduces the contact area of water on it and the presence of low surface energy waxy components with reduced affinity to water together leads to the superhydrophobic properties. The phenomenon is shown on Figure 1 (b). Cassie and Baxter (Cassie & Baxter, 1944) as well as Wenzel (Wenzel, 1936) proposed two mathematical models to explain the wetting phenomena on rough surfaces that leads to superhydrophobic properties. By definition, superhydrophobic surfaces are characterized by a water contact angle value = 150° with the rolling off of water drops from the surfaces (Sarkar & Saleema, 2010). Superhydrophobic surfaces find tremendous importance in the technological world where it can applied in domains such as anti-corrosion, anti-biofouling, electrowetting, icephobic and even in drag reductions (Bushnell & Moore, 1991; Cao, Jones, Sikka, Wu & Gao, 2009; Carlborg & van der Wijngaart, 2010; Carré & Mittal, 2009; Y. Huang, Sarkar & Chen, 2010a; R. Karmouch, Coude, Abel & Ross, 2009). However, the most important challenge faced by industries is their feasibility large scale in an effective an economical manner."

Jan 1, 2016

By Yann Sivry, S. Subramanian, Divyasree C. Prabhakaran, Jean Riotte

The potential of a bacterial strain isolated from water samples collected from a chromite mine in Odisha, India has been assessed for the bioremediation of hexavalent chromium, a toxic environmental pollutant. The isolate was identified as Sphingopyxis sp., a Gram negative bacterium, adopting molecular biological protocols and biochemical characterization techniques. Detailed investigations on the bioremoval of Cr(VI) were carried out using Sphingopyxis sp. cells and the various parameters affecting the biosorption process were evaluated. About 55 % biosorption of Cr(VI) was obtained using Sphingopyxis sp. bacterial cells and the residual chromium in solution was found to be bio-reduced to the trivalent form, namely Cr(III). Thus, complete bioremediation of Cr(VI) could be achieved using the mine isolate, with contributions from both biosorption and bioreduction mechanisms. The Cr(VI) biosorption isotherm obtained for the isolate was found to follow a typical Langmuirian behavior and the free energy value of biosorption was determined to be ~-25 kJ/mol, indicative of involvement of chemical binding forces in the bioremediation process. The chromium biosorption kinetics by the isolate followed a pseudo second order reaction. The FTIR spectral studies revealed that carboxyl, hydroxyl, amino and phosphate groups were involved in the biosorption process. X-ray photoelectron spectroscopic studies on the bacterial cells interacted with Cr(VI) confirmed the presence of both Cr(VI) and Cr(III) on the cell surface. The electrokinetic studies revealed that the surface potential of the bacterial cells were less electronegative subsequent to interaction with Cr(VI), compared to the cells alone, which further testified to the binding of positively charged Cr(III) ions, formed by bioreduction of Cr(VI), to the bacterial cell surface. A marginal shift in the iso-electric point obtained for the bacterial cells interacted with Cr(VI), corroborated the involvement of chemical binding forces in the bioremediation process.

Jan 1, 2016

By X Dai

This paper investigated the loss of cyanide via oxidation in CIP or CIL processes by relating the cyanide oxidation to its major oxidation product, cyanate. The results showed that the oxidation of both free cyanide and copper cyanide complexes are substantially enhanced by the presence of carbon. The rate of cyanide oxidation was found to occur in the order: Cu(CN)32- > CN- > Cu(CN)2-. The cyanide oxidation rate in the presence of copper and carbon increased significantly with increasing dissolved oxygen concentration, typical of CIL vs. CIP conditions. Cyanide oxidation rate of iron, zinc or nickel cyanide complexes was minimal.

Jan 1, 2011

By R. J. A. Fricker

IT is the purpose of this essay to give a reasonably complete description of shaft sinking under a rock pentice in a small Northern Ontario gold property. Hallnor is in many ways an exceptional mine, but the sinking operations here described are but typical examples of the excellent practice for which Canadian mines and mining engineers are justly famous the world over. The worth of the subject lies, therefore, nor in its originality, but in its soundness; not in the spectacular, but in the economical and safe. Attention is particularly drawn to the excellent safety record and to the exceptionally low overall sinking cost. INTRODUCTION Prior to April, 1939, the Hallnor No. 1 shaft had been sunk vertically to a depth of 997 feet below the surface. It is a three-compartment shaft, 19 ft. 10 in. by 7ft. 7 in. outside the timbers (see Figure 1).

Jan 1, 1941

By M. Maldonado

This work details the application of a decentralized control strategy to a pilot flotation column working with a two-phase system (water-air). The process is represented by a multivariable system composed of three inputs and three outputs. The selected control variables are the froth depth, the air hold-up and the bias rate, whereas the corresponding manipulated variables are the set-points of the local flow controllers of tailings, air and wash water. All controlled variables are estimated using electrical conductivity based techniques. In particular, the results of a new method for estimating the bias rate, based on the measurement of the volumetric fraction of wash water under the interface, is presented. This method reduces the coupling problem associated to the bias estimation as a difference between feed and tailing water rates. Moreover, the nominal system transfer matrix can be represented by an upper triangular matrix, in such a way that the closed-loop system stability reduces to the stability of the independent control loops. The experimental results show that the closed-loop system performance, particularly that of the bias rate loop, is strongly dependent on the air flow rate, reaching in some cases the saturation point of the controller.

Jan 1, 2007

By D. Michaud, C. Bazin, S. Lévesque, L. Pérez-Barnuevo, H. Longuepée

In recent years, with the emergence of Geometallurgy, a great effort has been made to characterize ore resources as early and accurately as possible, to allow better design and a more efficient operation of mineral processing circuits. In this context, core logging plays an important role, since drill cores provide the first insight into the ore characteristics. However, to satisfy geometallurgical requirements, traditional core logging does not suffice. New tools and methodologies need to be developed for the automation of core logging and the acquisition of mineralogical data better related to mineral processing performances. In this paper, a methodology for the geometallurgical characterization of drill cores is proposed, based on the drill core textural patterns. Textural pattern is defined here as the macroscopic spatial arrangement of minerals. The Mont-Wright iron ore deposit (Quebec, Canada) is used as a case study. The first part of this work aimed at analyzing the potential link between the iron ores textural patterns observed in drill cores and their response to ore processing, namely comminution and concentration. Preliminary results show similar performances in terms of energy consumption and heavy liquid separation for samples showing the same textural pattern. In the second part, this work seeks to develop a methodology for the automated identification of drill core textural patterns by the application of digital image analysis and discriminant function analysis. The results obtained show that this methodology is able to discriminate between the textural patterns identified at Mont-Wright with a good rate of success. Therefore, this work lays the foundation for the development of a new drill core characterization tool, which would allow for the early prediction of the iron ore behaviour during mineral processing through the identification of drill core textural patterns.

Jan 1, 2016

By Guangyuan Li

A 3-D block-spring model (BSM) has been developed for simulating the behaviour of jointed rocks. The model uses a discontinuous formulation and an iterative procedure to solve the large displacements in jointed and faulted rock masses. The 3-D BSM has been used to simulate mining excavations in jointed rocks around an open pit and underground settings. The applications have demonstrated that it is a practical tool to solve complicated problems of rock mechanics in civil and mining engineering. This model has recently been modified to incorporate complex geological conditions, such as underground water flow (seepage), unstable blocks and the time-dependent behavior of backfill materials. To demonstrate the capability of the 3-D model this paper presents the fundamentals of the 3- D BSM and its application for open-pit mining. A complete computer package BSM3D has been developed based on the 3-D block-spring model. The package consists of a solving engine for numerical analysis and a Windows based processor for mesh generation and results display. The multi-functioned pre-processor provides tools and menus to help users setting up models easily and conveniently. The fully featured post-processor allows users to view the results in different windows and orientations. The graphical results include contours, vectors, animation of rock movement, and the failure state of the rock structures.

May 1, 2001

By Akihiko Nishiyama

Unmanned construction technology used for remote control operation of construction machines has some problems to solve compared with manned operation of construction machines, such as fatigue due to long-term operation or decreases in operational efficiency. To solve these problems, we recorded the viewpoints of operators in both manned and remote control operation and analyzed the differences. This paper reports on our discussion of improving the operability of remote control operation based on the analysis results.

Aug 1, 2013

By B. Stettner, J. Asante, S. Abraham

The levels of nitrogen in steel produced in various metallurgical vessels vary significantly. For example, the tap nitrogen levels in steel produced in the BOF are around 4Oppm, as compared to 70-100ppm in both DC and AC electric arc furnaces. Given the pressing need to reduce nitrogen levels in steel to satisfy customer demand, IPSCO Inc. has gained considerable experience in controlling nitrogen levels in steel over the course of the last three years. Hence, a cost effective process has been developed through an intensive nitrogen control program from steel melting in the EAF through to the continuous slab casting stage. This paper describes the practices employed at each stage of the steelmaking process that have enabled IPSCO Inc. to reduce and control nitrogen levels in steel.

Jan 1, 2004

By D. Stone, N. J. Aslin, W. Webb

In today&apos;s modem copper electro-refineries, increasingly higher average current densities are being employed. With these increases many refineries are approaching their limiting current density. The nearness of the average operating current density to the limiting current density has placed increasing emphasis on the need to maintain an even current distribution. This paper explores the importance of maintaining even current density and discusses the factors, processes and practices that are necessary to achieve and maintain high quality production at high operational intensity.

Jan 1, 2005

By E. Latorre, T. S. Golosinski

ABSTRACT; his paper proposes new methodology to define the pit limits that yield the maximum net present value (NPV) for a deposit, under a given economic scenario and for a given discount rate. The method uses an algorithm that combines dynamic programming and heuristics. It was tested for evaluating deposits with different sizes and various grade distributions. For the discount rate of zero, the results confirm that the economic pit limits are the same as that defined using Lerchs Grossman method. However, when discount rates higher than zero are used, the pit limits differ, yielding a higher NPV.

Jan 1, 2011