Search Documents

By Roussos Dimitrakopoulos

Overview ?Uncertainty matters: The economic side ?Models of geological uncertainly ?Shifting the paradigm: Stochastic mine planning ?Using uncertainty to improve project performance ?Conclusions: Quantified uncertainty based models are great!

Oct 1, 2010

By R. S. James, S. P. Goff, A. E. Armitage

"Oxide-facies banded iron formation in the Third Portage Lake area is hosted by ultramafic and calc-alkaline volcanic rocks and related sedimentary rocks of the Archean (2.8 Ga) Woodburn Lake Group, 80 km north of Baker Lake. These rocks record at least two phases of metamorphism/ metasomatism. Greenschist facies metamorphism, in the temperature range of 370°C to 520°C and at pressures above 2.3 kbar, has affected all rocks on a regional scale. Later mineralization and alteration of banded iron formation (BIF) and associated volcanic rocks resulted from metasomatic fluids which carried Mg, K, Ca, S, As, Cu and Au. These fluids were confined to ductile to brittle, cross-cutting and layer-parallel micro-shears developed in the thickened hinge region of a shallow plunging recumbent fold. Metasomatic reactions yielded cummingtonite + biotite-bearing assemblages which are associated with strongly mineralized iron formation. Pyrrhotite is the dominant sulfide phase and occurs within ductily deformed iron formation where it pervasively replaces magnetite. Minor fine-grained chalcopyrite and arsenopyrite generally occur as inclusions within pyrrhotite and recrystallized magnetite, and rarely as individual grains. Pyrite is restricted to brittlely deformed iron formation, and to the contact between iron formation and altered ultramafic rocks, where it is associated with quartz veins. Pyrite typically replaces pyrrhotite. Native gold is associated with both pyrrhotite and pyrite, but higher gold concentrations are associated with pyrite. Grunerite/Ca-amphibole + stilpnomelane and sparse pyrrhotite and pyrite characterize weakly mineralized iron formation. Within adjacent ultramafic rocks, metasomatic reactions yielded assemblages of interlayered Ca-amphibole + biotite, and talc + Ca-amphibole + carbonate + biotite. K-Ar geochronology on metasomatic biotite from mineralized BIF yielded a 1791 ± 32 Ma age.An epigenetic model is favored for the emplacement of gold. The age of the gold mineralization in the Third Portage Lake area is uncertain, but may be Proterozoic based on the preliminary isotopic age and by analogy with Proterozoic gold deposits elsewhere in this part of the Churchill Structural Province. Copyright"

Jan 1, 1996

By W. S. Fyfe

Gold is mobilized and precipitated in a wide variety of environments ranging from those of weathering and biological phenomena, to pluton emplacement to deep metamorph ism . But it appear that pervas ive leaching of large rock volumes fo llowed by the focussed di charge of typically low salin ity flu ids is frequently involved. There are great gaps in our knowledge, particula rly with re pect to gold in very high temperature fl uids generated at near Moho depths. But uch flu id may play an important part in Archaean pluton associated lode gold deposits whe re ultra high temperature fluids, rich in C02-CO-COS, may be associated with magma underplating and crustal assi mil ation processes (sag subduction) associated with very den e ult ramafic magma . Other environment with great potential include those of major thru t fau lt and strike slip fa ult s where large quant ities of fluids are mobilized .

Jan 1, 1986

By P. C. Lightfoot, J. M. Duke, A. J. Naldrett

"The segregation of magmatic sulphides from mafic and ultramafic silicate magmas, in many circumstances, leaves the magma with a lower-than-normal Ni/MgO ratio, which is characteristic of both lavas erupted from the magma chamber and olivine crystallizing within it. Two end members of the segregation process are discussed; i) batch segregation and ii) fractional segregation.In the former, the critical factor is the magma/sulphide ratio. Computer modelling suggests that where this ratio has been less than 1000, the magma will be recognizable as anomalously low in Ni, due to sulphide segregation, and thus a good target for exploration. In fractional segregation, the critical factors are the proportion of sulphide to silicate being segregated and the degree of fractionation.Samples believed to represent the liquid portion of komatiitic lava f lows from a series of unmineralized sequences in the Abitibi greenstone belt, Canada. Belingwe belt, Zimbabwe, and Barberton Mountainland, South Africa coincide with the sulphide-free fractionation model. They are in marked contrast to samples from the ore-bearing districts of Kambalda and Scotia. Western Australia in which distinct Ni depletion, corresponding to fractionation of olivine plus sulphide in a ratio of between 100 and 200:1 is recognizable. Ni-depleted olivines also mark the sulphide-bearing Dumont intrusion of the Abitibi belt.The Moxie intrusion of northern Maine has distinctly Nidepleted olivines, as does the nearby and petrologically related Katahdin body. In both of these intrusions, the composition of the olivine allows reasonable predictions to be made of the Ni tenors of sulphide showings within them. At Katahdin, the Ni depletion is so widespread that little hope is help out for the presence of economic concentrations of sulphide. At Moxie. the olivine compositions suggest that the best chance of economic sulphides lies in the southern lobe of the intrusion.Ni-depleted olivines also characterize certain rock units within intrusions of the Insizwa complex, Transkei, Southern Africa. Many millions of tonnes of Ni have apparently been removed by sulphides from these rock units, many more than are contained within the single mineralized occurrence so far identified at Waterfall Gorge."

Jan 1, 1984

By Donald A. Cranstone

"This paper provides a bird's eye view of the pattern of gold discoveries since 1823, the year of Canada's first gold find, up to 1983. Within this 160-year period, more gold was discovered in Canada during the last ten-year period (1973-1982) than during any previous decade. The record suggests that the potential for further major gold discoveries is high, which bodes welt f or the future of Canadian gold mining.IntroductionCanada has an impressive history as a gold producer. Since 1921 we have occupied second or third place among the world 's gold producing nations, after South Africa and most of the time the U.S.S.R. Canadian gold production over the last hundred years has added up to some 6 per cent of all-time world production.The sharp rise in the price of gold in the 1970s led to a surge of gold exploration, which in turn resulted in the discovery of significant quantities of gold in Canada. How do these recent discoveries rate in comparison with those of the more distant past? For example, are the quantities of gold in notable discoveries of recent year s, such as Hemlo and Detour, in the same league with the amounts of gold discovered around 1910 in the Porcupine and Kirkland Lake district s of Ontario? Can the combined gold content of the recent discoveries be likened to that o f the almost 40 major Canadian gold deposits, along with numerous smaller ones, discovered in Canada during the 1920s and 1930s? What are the implications of the more recent gold discovery record for future rate s of gold discovery in Canada?This paper attempts to glean answers to such questions from an overview of the period that begins in 1823, the year of Canada's first gold discovery. Gold deposits come in two major types: placer deposits and lode deposits in solid rock . Placer gold is distributed in sand and gravel. Gold in solid rock occur s mostly in gold ore filling fissures."

Jan 1, 1985

By Kri Inwood

"IntroductionIn 1879, when the Dominion government initiated its controversial program of industrial promotion, iron smelting in Canada was limited to one company producing coke iron on the mainland of Nov a Scotia and three small charcoal blast furnaces in Quebec. There was no steel production. By the eve of the first great war, iron and steel were being produced in very large quantities, the companies active in 1879 had disappeared and new centres of integrated iron and rolled steel production at Hamilton, Sydney and Sault Ste. Marie had come to resemble the industry as we know it today.The most dramatic change was that at Sydney, Nova Scotia, where in the early 1900s, two steelmaking companies established works. The Sydney developments have been explained as the result of resource discovery and technical change. W.J. Donald, in his authoritative account of the Canadian iron and steel industry, observes:""The most rapid growth of the Canadian iron and steel industry has occured since 1897... The remarkable growth has been caused largely by the new conditions of the industry. The discovery and use of Newfoundland ores, together with the availability of Cape Breton coal, has made the Nova Scotia industry not only possible but profitable ... It is a safe conclusion that the Canadian industry would not have been an important one, had it not been for the discovery of the Michipicoten and especially the Wabana (Newfoundland) ores""Donald also argues that metallurgical progress had been necessary to render the ores valuable,""Newfoundland ores ... contain a considerable amount of phosphorus, and were made available for steel-making by recent inventions.""The purpose of this paper is to re-examine Donald's story. It will be argued that the origin of steel -making at Sydney is somewhat more complicated than Donald has indicated. The difficulty with Newfoundland ore extended beyond its phosphorus content and a resolution required more than the basic open hearth furnace identified by Donald. Moreover metallurgical change was only one of several developments necessary to induce industrial investment at Sydney. Surprisingly, however, the discovery of iron ore in the late nineteenth century does not appear to be part of the explanation."

Jan 1, 1983

To create a successful growth oriented diamond company that succeeds in the practical business of mining and selling rough diamonds, and which pursues an aggressive exploration strategy to seek and develop worldclass diamond mining opportunities in a market that has become increasingly under-supplied.

May 1, 2008

By A. W. F. Smith, P. B. Prangnell, D. N. Crowther, P. J. Apps

It is well known that the refinement of grain size in metals leads to a significant improvement in important mechanical properties. As part of a European collaborative project, processing schedules have been investigated aimed at producing a homogeneous ultra-fine ferrite and spheroidised carbide aggregate microstructure structure in high carbon (CMn) steels (0.6-1.2wt%C), via conventional 'warm' rolling and innovative Equal Channel Angular Extrusion (ECAE). Suitable deformation schedules were determined from dilatometry and thermo-mechanical Gleeble simulations. Evidence of an ultra-fine ferrite and carbide aggregate microstructure following 'warm' rolling is given. A significant improvement in tensile strength, particularly proof stress (0.2%) was also noted in comparison to material deformed at higher temperatures. Concurrent Equal Channel Angular Extrusion (ECAE) experiments investigated microstructural evolution with incremental strain. Extensive analysis was carried out using various techniques, including high resolution Electron Back Scattered Diffraction (EBSD). Evidence of ferrite grain refinement was noted in a eutectoid composition steel. A sub-micron ferrite structure was observed following high strains (E-3.33) and the mechanical properties exhibit a marked increase in tensile strength.

Jan 1, 2004

By Marko Lampi, Ross Andrews, Jouni Pihlasalo, Robert Matusewicz

With widespread discussion on reducing carbon, sulphur and other emissions, use of sustainable energy sources and the pivotal circular economy theme, consideration needs to be given to pyrometallurgical operations broadly and more specifically, non-ferrous metallurgy. These themes present a number of challenges in terms of current operations and the view of processing the metals which are largely taken for granted in day to day living. This paper considers how these themes will impact pyrometallurgical flowsheets using the non-ferrous base metals as an example. It will examine the flowsheet chain to offer views on the boundaries of flowsheet optimization and the application of available tools to meet these future goals and challenges. INTRODUCTION The themes of reducing footprint through lowered CO2, S and other emissions, together with process sustainability (e.g. lowered energy) and links to the circular economy are well known to everyone in the metals industries. Whether it is reducing greenhouse gas emissions or analysing the importance of metals recycling in the circular economy, all these themes carry with them the fundamental premise of any change being considered; how can you best optimize a system to meet your aims? Of course, this depends on the available tools and the approach used for optimisation.

Jan 1, 2019

By Gabriel Voicu, Marc Bardoux, Ross Stevenson, Nuno Machado, Jean Lafrance

"Abstract - Paleoproterozoic gold is found in two different volcano-sedimentary sequences and intrusive bodies separated by 600 km within the Guiana Shield. The 2148 Ma St-Élie granite intruded volcanic-arc sequences of the Paramaca Group, whereas the 2096 Ma Omai stock penetrated backarc/ island-arc sequences of the Barama-Mazaruni Group. Positive ?Nd values suggest that both suites lack Archean crustal contaminants, which is consistent with an origin in an oceanic arc setting.The St-Élie deposit is characterized by quartz-dominant vein systems with minor metallic minerals, represented chiefly by pyrrhotite and pyrite. Biotite, calcite, and chlorite are the main gangue minerals. The alteration haloes at St-Élie feature a strong potassic zone, which is absent at Omai. The ore-controlling structures are ductile and the vein emplacement is related mainly to contemporaneous, high-angle ductile shear zones. The St-Élie deposit formed at temperatures >350°C. The stable isotopes values are compatible with a magmatic or metamorphic source.The Omai deposit is characterized by quartz-dominant vein systems with minor metallic minerals, represented mainly by pyrite. Ankerite, scheelite, albite, and chlorite are common gangue minerals. The vein emplacement is syn- to post-deformation and it is related mainly to brittle shear zones with low-angle, stockwork networks and breccia zones. The Omai deposit formed in a temperature range between 250°C and 170°C, much lower than the St-Élie deposit. The stable isotope values are compatible with mixing between deep-seated fluids of metamorphic or magmatic origin with surface- derived fluids.These differences between St-Élie and Omai are interpreted in terms of their depth of formation. Alteration patterns, structural elements, and paragenetic assemblages indicate that the gold at St-Élie was most probably emplaced at a mesozonal depth, whereas the Omai setting yields evidence for epizonal conditions."

Jan 1, 1999

By Fatemeh Pourakbari, Mohammad Reza Yarahmadi, Abbas Sam

Pyrite is the most abundant sulfide gangue mineral in copper porphyry ores. In spite of addition of lime in large quantities to depress pyrite in flotation, considerable amount of this mineral is reported to concentrate, particularly in rougher and scavenger stages. With the Sarcheshmeh pit advancing to a greater depth and reaching to the hypogene zone, the amounts of pyrite and chalcopyrite in the feed are increased. Hence, a reduction in the copper grade and increase in the sulfur content of the concentrate are observed. In this study the effective factors on the pyrite floatability at the circuit flotation was considered at Sarcheshmeh Mine. Mineralization zones in the pit were firstly identified. Then, sampling points were located using GPS system. On the basis of mineralogical composition and morphology, the ore was categorized into five main classes. In this classification the amount of lead and zinc and also pyrite locking with other minerals were analyzed. The study of polished section indicated that inclusion in pyrite was very frequent in all classes, mostly composed of the floatability of pyrite. Flotation tests were performed on the samples of different classes at pH of 11.8 after conditioning time. It was shown that, pyrite floatability was decreased with a decrease in the lead content of the feed samples except for the second class, while for all classes an increase in zinc content contributed to a decrease in pyrite floatability and recovery. It was found that, the lowest pyrite recovery (1.89%) was corresponding to pyrite–molybdenite dominant mineralization with Zn of 0.33% and the highest recovery (86.89%) corresponding to pyrite vein dominant mineralization with Zn equals to 0.9%.

Jan 1, 2016

By Alan E. Renshaw

"This paper is a practical overview of ways to reduce cost in the design and operation of an Arctic mine. The economically important issues of the Arctic mine that will be addressed include: permafrost and the active zone in general terms; road building in and over permafrost; Arctic geotechnical mine design considerations; pit dewatering techniques in sub-zero temperatures; and blasting frozen materials with techniques to obtain optimal results. A final section on a few special topics conclude this paper.Although this paper primarily refers to near surface conditions more closely associated to an Arctic surface mine, many of the ideas and techniques contained in the paper also apply to the surface construction of an Arctic underground mine."

Jan 1, 1996

By K. L. Ford, D. R. Lentz, J. H. Rickard, R. P. Taylor

Abstract - Coupled gamma-ray spectrometric and lithogeochemical studies throughout the Heath Steele Mines area, Bathurst Camp, New Brunswick, indicate that primary and secondary geochemical differences exist between the stratigraphic footwall and hangingwall crystal tuff units which host the massive sulfide deposits. Of particular interest is Th, and to a lesser extent, Zr and Y, which are more concentrated in the hangingwall than the footwall crystal tuffs, whereas the opposite is true for TiO2. This expands on earlier lithogeochemical-chemostratigraphic results concentrated in the eastern part of the Heath Steele belt that led to revision of the local stratigraphy, and necessitated a structural re-interpretation of the area with implications for exploration. Although K depletion (decreased K and K/Th) is typical of chloritized footwall zones of chloritization, these features were not fully apparent here due to the recessive nature of these altered zones. In situ radiometric analysis using a portable gamma-ray spectrometer is a rapid, inexpensive analytical technique for chemostratigraphic characterization of rock units within volcanogenic massive sulfide deposit settings, provided there is a contrast in the distribution of natural radioelements, particularly Th and K.

Jan 1, 1998

By G. T. Lapidus, A. Garcés, O. J. Restrepo

"Colombian nickel laterites have historically been processed by pyrometallurgy. However, due to the depletion in ore grades, alternative processes are required. Hydrometallurgical processes, such as pressure acid leaching, have been proposed as alternatives to extract nickel from deposits with suitable characteristics. Such a leaching process requires high concentrations of acid to achieve acceptable extractions, and is not selective. In this study, an alternative aqueous alkaline glycine system has been employed to evaluate the leaching behaviour of a Colombian nickel laterite which contains 1.15% Ni, 0.12% Co and 41.1% Fe. Additionally, the effect of the addition of chloride ions, the use of a reducing agent and the application of a pre-treatment to improve the extraction of nickel were evaluated. Extractions of 4.63% Ni, 42.16% Co and 0.33% Fe were obtained using a 1M solution of glycine at pH 9. In addition, an increase in nickel extraction from 4.63% to 25.68% was achieved by applying a pre-treatment to the sample. The results show that even though nickel dissolution was much slower than in acid leaching, it was selective over other metals such as iron, proving the proposed method to have potential as a process for the extraction of nickel from Colombian laterites.INTRODUCTION Before 2010, most of the industrial operations used pyrometallurgical processes for the extraction of nickel, mainly in saprolitic regions of deposits, with greater contents of the metal. Nevertheless, due to the gradual depletion of such deposits, different hydrometallurgical processes have been studied as alternatives to process those nickel laterites with low grade and those which present problems of refractoriness due to the presence of acid consuming materials (McDonald & Whittington, 2008; Oxley & Barcza, 2013; Wang et al., 2012). However, such leaching processes require high concentrations of acid to achieve acceptable extractions and they are not selective. Facing lateritic nickel ore deposits containing high levels of acid consuming materials, an alkaline leaching medium becomes an advantageous alternative over acidic media, due to the increase in selectivity and decreased corrosiveness and reagent consumption (Tanda, Eksteen, & Oraby, 2017). Unlike conventional acidic reagents used for metal recovery, alkaline reagents can selectively dissolve the desired metal, leaving in the solid residue other elements such as iron, magnesium and aluminum, which are problematic in subsequent stages of metals separation and recovery. Furthermore, there are no serious corrosion problems associated with alkaline leaching, even at higher reagent concentrations, or at elevated temperature and pressure (Ntumba Malenga, Mulaba-Bafubiandi, & Nheta, 2015)."

Jan 1, 2017

By F. Goodarzi

"The nature and distribution of the inorganic components and the concentration of certain environmentally sensitive elements, such as, As, Sb, B, Hr, Cd, CI, F, Mo, Pb, S, and Se, or elements detrimental to the utilization by industry such as B, Na, P and S are very important in determining coal quality. The concentration of elements in coal is controlled by the following factors: (1) frequency of occurrence of partings; (2) nature and habit of occurrence of minerals in coal; (3) environment of coal deposition; (4)rank; (5) geological setting; and (6) weathering.Selective mining of coal can reduce the input of undesirable elements such as As and S by eliminating the part of the seam which is enriched in these elements. IntroductionCoal is a sedimentary rock of plant origin and consists of two components: an inorganic component (minerals) which is formed by influx of clastic sediments into the coal-forming environment and also by activities of groundwater, and an organic component (macerals) which is formed from plant debris deposited in the original coal-forming environment. However, coal is a generic term with a broad range of utilization characteristics. A coal that is attractive for use in one market - such as generation of electricity (combustion) - may not necessarily be acceptable for use in another, such as for production of coke (Davis, 1978).The elements in coal are associated with both macerals and minerals. The elements associated with coal macerals, such as C, H and N are termed elements with organic affInities. The concentration of elements with organic affmities (including B, Br, CI, F, I, S, and Mg) often decrease with increasing ash content of coal (Nicholls, 1968; and Finkehnan,1982). FIgure 1 shows such a trend for chlorine. Some of these elements may also be incorporated in coal maceral as very fine mineral grains (Finkelman, 1982). The elements with organic affmities are often volatilized during combustion and carbonization of coal and emitted in the vapour phase. Emission of some of these elements (C, 0, Br, N and S) is of major environmental concern (Lim, 1979)."

Jan 1, 1994

By R. M. Giegerich

"This paper begins with a brief history of Madawaska Mines, a brief description of the geology, mining methods and equipment, and the historical development of 7/8-in. tapered drilling equipment. It then outlines the performance characteristics and inherent problems of the traditional 12-degree, tapered connection, blade-type insert bits. Service-free (Unipass) button-type insert bits are presented as a possible solution to these problems. The paper concludes with an analysis of button bit performance to date.Brief History of Madawaska MinesMadawaska Mines Limited, near Bancroft, Ontario, is in Faraday Township, Hastings County, approximately 100 miles northeast of Toronto and 100 miles west of Ottawa.The mine re-opened in 1976committed to 1,500 tons per day to provide approximately 600,000 pounds of yellowcake (U3O8) per year to A.G.I.P. (an Italian government agency) under the joint ownership of Federal Resources Corporation, Salt Lake City (51%), and Consolidated Canadian Faraday Limited (49%). At present, the mine is producing approximately 2 pounds per ton (.1% U3O8) at the rate of 60,000 pounds per month. The mine employs about 400 employees.Brief Description of Geology, Mining Methods and EquipmentGeologyThe Grenville metasediments of the mine area are chiefly paragneiss, amphobolite and some carbonate (marble) rocks, which were intruded by a basic rock, altered to a metagabbrometadiorite. These formations are generally concordant, striking east to northeast and dipping 45 to 60 degrees to the south. Locally, the metagabbro is often discordant. The above group of rocks (mixed hybrid gneisses) forms the hanging wall of the south-dipping Faraday granite sheet and was intruded by nepheline syenite, syenite and granite. The ore occurs in the granite-syenite-pegmatite dykes that are probably genetically related to the Faraday granite. The ore shoots are erratically distributed within the pegmatite bodies, mainly on the hanging or footwalls but also medially. Their size varies from 50 to 350 feet in length, 5 to 40 feet in width and 50 to 200 feet in height. The ore occurs most frequently in a medium-grained granite or syenite, well hematized with 10 to 30% mafic crystals of pyroxene, amphibole and/or relics of the host rock."

Jan 1, 1982

By E. Goodwin

"Maclaren Forest Products Inc.Lime is commonly used for the neutralization of acid, and the removal of heavy metals in mine waste waters. However, the precipitation of heavy metals as hydroxides must take place under conditions of controlled pH, to produce minimum concentrations of dissolved metals. An account is presented explaining the concepts applied to lime-treatment processes at Bell Mine during the period of a supernatant discharge to Babine Lake; October 18, 1982to January 25, 1983. IntroductionBell Mine of Maclaren Forest Products Inc., Babine Mining Division, an open-pit copper mine, is located on Newman Peninsula, Babine Lake approximately 65 kilometres northeast of the town of Smithers, British Columbia (Fig. 1).A depressed market for copper metal in 1982 forced a management decision to suspend operations at the mine for an indefinite period from October 3 I, 1982. For some time prior to the mine closing date, mine management was concerned about the increasing level of supernatant in the tailings pond , and its possible effects on the stability of the dam when cycloning of mill tailings ceased. Consideration of these potential hazards led to an application being filed with the Provincial Waste Management for a permit to discharge the excess water to Babine Lake. This large lake, an important link with several significant salmon spawning sites, is a major contributor to the British Columbia commercial fishing industry. Jurisdiction for the environmental affairs in the area is shared by the Department of Fisheries and Oceans, the Environmental Protection Service, and the Provincial Waste Management Branch. These agencies were directly concerned in the formulation of discharge permit following joint consultation, and exchange of information with the company on environmental concerns. An approval was finally granted to discharge approximately 1,000,000 cubic metres of supernatant from the tailings impoundment at Bell Mine into Hagan Arm, Babine Lake from October 18, 1982 with a daily discharge not to exceed 9000 cubic metres. Provisions were made that a particular discharge procedure be followed, and that the company would be responsible for setting up a sampling and monitoring program to safeguard the quality of the effluent."

Jan 1, 1986

By J. D. McFarlane, V. Robinson

"The paper begins with a brief account of the naturarly occurring resources of gypsum and anhydrite and a discussion of their relative value and utility as sources of sulphur. The fundamental chemistry of recovering sul-phur values from calcium sulphate is discussed. (a) Thermal decomposition -discussed as impracticable; (b) Reduction to calcium sulphide; (i) Total Reduction-The chemistry is outlined and the Dorr-Oliver and Bureau of Mines processes mentioned. The Elcor process is mentioned and certain deductions made from available information.(ii) Partial Reduction-This is stated as the basis of the only proven process, namely ""The Cement -Sulphuric Acid Process."" The possibility of recovering lime is mentioned as an aside, but dismissed for lack of commercial application. The history of the cement -sulphuric acid process is covered briefly and a list of plants in commercial operation included. A brief elementary account of the basic chemistry of cement production is followed by a discussion on raw materials and fuels. A short account of the flow scheme of a typical plant, with notes on the operating peculiarities, precedes an account of product quality. The latest developments which enable by-product gypsum to be used as a raw material are discussed, with an indication of how the flow scheme is modified. A statement of feasible plant capacities is followed by requirements of raw materials, services, labour, etc., and finally some indication is given of capital costs."

Jan 1, 1969

By S. Konetschnik, Lux Degel, R. Degel, T. Haslinger

UrbanGold and its partners from Mettop and SMS group have developed a novel technology for the recovery of valuables from all non-ferrous metals’ fractions of WEEE (Waste Electrical and Electronic Equipment), with a special focus on low qualities which are commonly landfilled or incinerated. The technology is marketed under the brand name “UrbanGold Flex” to illustrate the high flexibility in respect of plant design and raw material portfolio, allowing also the processing of low grade material and materials with high caloric values. The process of the technology’s centrepiece, a modified and enhanced bath smelting furnace called “HENRI”, was investigated in numerous pyrometallurgical trials as basis for a scale-up towards a capacity of up to 100,000 tons of WEEE-concentrates per year. All relevant facility components have been evaluated in respect of references, fall-back options, as well as exit strategies (alternatives) to minimize risks when establishing a novel technology. A spin-off within the development is the “UrbanGold Compact” technology which can be seen as optimization of state-of-the-art smelters by using an optimized TBRC as primary processing unit. As an UrbanGold Compact plant will be the first industrial scale reference of UrbanGold’s technologies, it is also explained in the publication. As precious metals recovery is of major (economical) importance when recycling WEEE, major attention has been given to minimize the losses of these valuables. These measures, as well as a sophisticated way of utilizing waste heat as far as possible, result in interesting business cases with gross profits of up to 20% or even more. INTRODUCTION Over the past years, the demand of electrical and electronic equipment has increased dramatically with technological progress. Innovations on the technology of electronic devices led to a shorter usage and lifespan and thus boosted the generation of Waste Electrical and Electronic Equipment (WEEE). WEEE is one of the fastest growing waste streams, growing at 3 to 4% per year worldwide and is expected to reach more than 52 million tons per year by 2021. Currently, about 45 Mt of these wastes are estimated to arise worldwide, and the trend is rising (Baldé et al., 2017).

Jan 1, 2019

By M. I. Abbas, M. A. Shahin, M. S. Ahmed

"The influence of annealing of galvanized steel (galvannealing) on its corrosion kinetics in a saturated solution of Ca (OH)2 has been studied by means of the polarization resistance method.Galvannealing heat treatment was carried out at 450°C and 550°C for varying times. Annealing at 450°C for 24 hr or at 550°C for 5 hr showed the highest corrosion potential (Ecorr) ~= - 400 m V/ SCE as well as, the lowest corrosion current density (icorr ~= 3 mA.cm-2, while Ecorr and icorr of the unheated specimens were ~= - 1400m V/SCE and == 20 mA.cm-2, respectively.Polarization curves were also obtained for the as-received galvanized specimens together with the galvannealed ones.INTRODUCTIONHeat treatment of galvanized steel (i.e . galvannealing) is carried out at a temperature range of 450°C to 550°C for a time sufficient to convert the free zinc coating to an alloyed one consisting of layers of iron-zinc intermetallic compounds. Table I is a review of the properties of the Fe-Zn intermetallicphases while Figure I is a reproduction - of the Fe-Zn equilibrium phase diagram taken from Hansen.Several authors have studied the formation of intermetallic phases through the interdiffusion of Zn/Fe couples. Their results confirmed the stability of intermetallic phases that could be shown up on the outer surface as a result of galvannealing of galvanized steel.Bernick and Sievertv"" investigated the processing of galvan nealed steel. They found that the galvannealed coating with the best forming qualities consisted of a mixture of Zeta phase and Eta phase."

Jan 1, 1989