Search Documents

By D. J. Farmer

Mining hoists are major components of any underground mine, however, the detailed design work required to get the actual power required for a particular hoist is outside the scope of preliminary feasibility studies. Nonetheless, a hoist is costly. Therefore, an accurate estimate is needed for the design parameters and the power required. There are two methods available, namely, the O’Hara method and the Society of Mining Engineers’ method. Tests were done for both methods employing nine friction hoists and 19 drum hoists currently in use at Canadian mines. The O’Hara method provided unacceptable results for both friction and drum hoists. While, the SME method was designed for American regulations and factors of safety which often differ significantly from Canadian ones, good results were obtained. The two relationships deter-mined were simply to add 5% to friction hoist design and to add 4% to drum hoist design. Modifying the SME method by these two factors will allow the hoisting system determined by the SME method to be within the error for a prefeasibility study.

Jan 1, 1997

By S. G. Shabestari

Thermal analysis is a tool that is generally employed to predict the structure of the alloy before the actual casting is carried out. By cooling a sample of the molten alloy and recording the temperature-time curve, important solidification events may be analyzed by using the first derivative-cooling curve. In this research, strontium is added to (AS5U3G) 319 aluminum alloy and its influence on the formation of intermetallic compounds e.g. Al15(Mn,Fe)3Si2, Al2Cu, Al5Mg8Cu2Si6 formed during pre- and post-eutectic reaction have been investigated. Also any changes in solidification parameters such as temperature of Al-Si eutectic under cooling and temperatures of nucleation and growth of each phases caused by strontium addition, have been determined via the first derivative cooling curves. The effect of strontium on the formation of various intermetallic compounds has been studied by using very accurate thermal analysis equipment and the microstructures were analyzed using an optical microscope. The various phases reported in this paper were identified using Scanning Electron Microscopy (SEM) and linked to Energy Dispersive Spectroscopy (EDS). Formation of all pre- and post-eutectic phases was interpreted by comparing the phases formed in the microstructure and the reactions detected by using cooling curves. The results of this research indicate that thermal analysis technique can be used as an on-line process control in the production lines in aluminum casting industries.

Jan 1, 2004

By B. Currie

Maintenance of quality electrowon copper requires an electrolyte which has suitable chemical and physical characteristics. The proper design and operation of the solvent extraction plant is essential to the quality of the electrolyte sent to electrowinning. An aspect that is not well appreciated is that the return electrolyte can have negative effects on the operation of the solvent extraction plant. Poor SX plant operation creates below optimum electrolyte conditions. High Eh in the return spent electrolyte can degrade the SX reagent with large decreases in copper transfer capacity and increases in internal entrainment. The synergistic interaction of the SX and EW plants needs a single-source design approach to address the interactions. The design elements in the SX and EW plants required to manage the electrolyte conditions are discussed.

Jan 1, 2014

By H. Q. Fan

Construction equipment is an important type of resources of heavy construction contractors. Since equipment breakdowns can cause project delays and significant financial losses, the contractors are eager to know those factors causing equipment failures directly or indirectly, related to equipment design, maintenance, and operations. Although Bayesian network can be used for diagnostic analysis of failure events or making predictive analysis, building a Bayesian network for such purpose can be difficult as the cause-effect relations can be subjective and their conditional probabilities change with a wide variety of causal factors. A hybrid approach is proposed in this paper to update the Bayesian diagnostic network structures and parameters using real life data, the conditional probabilities and cause-effect relationships can be dynamically updated with observed failure records to reflect the real life situations of a complex equipment system. A case study is conducted to show the benefits of the hybrid approach in construction equipment diagnostic analysis.

Aug 1, 2013

By M. C. Walton, W. Roelofs

ABSTRACT: In most cases, a refractory repair involves dealing with used refractory linings above shoulder height, defining these as overhead refractories. This paper details a method of personnel protection involving a low-pressure inflatable balloon system, installed to prevent the dislodgement and freefall of in-situ refractories. This system has been successfully applied to numerous types of vessels in the process industries in the last three to four years. This paper, prepared for the CIM Conference of Metallurgists held in Vancouver, British Columbia in October 2010, outlines details of the system and gives examples of successful applications.

Jan 1, 2012

By S. Kashani Nejad, M. Bellino, K. Collins, C. Tovee, J. Godwin

Motivated by safety considerations, logistical issues, transportation cost savings, product diversification, and marketing preferences, several uranium producers are revisiting their business models and supply chain configuration and, instead of selling dried yellowcake to downstream refineries, they are moving to build in-house calcining facilities. Drying and calcining plants are relatively low-cost facilities to build and operate. The execution period of a typical yellowcake drying and calcining project is also relatively short and alternative construction methodologies, such as modularized solutions, are available. The drying and calcining technologies used for yellowcake are relatively mature, environmentally contained, and well supported by qualified vendors. The drying and calcining circuits also seamlessly integrate with upstream and downstream operations. These either produce a dried yellowcake or calcined U3O8 which are notably safer and easier to transport and market. This paper presents an overview of the recommended technology and project development considerations for yellowcake drying and calcining facilities.

Jan 1, 2020

By V. Songmene, R. Khettabi, J. Masounave, R. D. Njoya

L'augmentation régulière des règlements environnementaux et de la sécurité au travail deviennent de plus en plus strictes. L'usinage fait partie des opérations industrielles qui peuvent causer des problèmes de santé au travail et sur l'environnement. La plupart des particules de poussières produites pendant toutes les opérations d'usinage à sec ou lubrifie causent des nuisances environnementales graves. Le travail propose étudie l’influence des paramètres de coupe, des alliages et des états des matériaux sur la formation des copeaux et sur la génération de poussière lors de l'usinage à sec. Deux modes d'usinage (le fraisage et le perçage) sont abordés. Une loi reliant la ténacité des matériaux aux émissions de poussières est proposée. Les effets des matériaux et de leurs conditions, ainsi que des procédés d'usinage sur la génération des poussières ont été mis en évidence. Des mécanismes de formation de poussières sont identifiés et reliés à la formation des copeaux.

Jan 1, 2006

By B. Yamamoto, D. Post, J. De Leon, A. Meike

"This paper describes the theory, design, building, and testing of the passive magnetic bearing stabilizing system which is the core of the passive magnetic bearing system. The stabilizing system is made up of two large magnetic disks opposing themselves with a stabilizing disk in the center which allows the system to self-locate in a null position without the need for external power sources or sensors. When outside forces act upon the stabilizer, the magnetic fields interact with the stabilizing plate to return the system to its null position. Collaboration between two industry leaders has allowed an actual prototype to be built and tested providing real data to prove out the theory.INTRODUCTIONMagnetic bearing/stabilizer systems have many advantages over conventional mechanical bearing systems. These include near-zero drag losses and no need for lubrication since the rotating elements make no mechanical contact with the stationary elements of the bearing system. However all magnetic bearing systems must contend with a constraint known as Earnshaw’s Theorem in the early 1800’s, this theorem asserts the impossibility of constructing a stable, non-contacting, electrostatic or magnetostatic levitation system using only fixed charges or fixed magnetic poles, such as those produced by permanent magnets. Because of the constraint imposed by Earnshaw’s Theorem virtually all present-day commercial magnetic bearing systems are of the “active” type. That is, they employ electromagnets that are powered by amplifiers the inputs to which come from sensors embedded in the bearing system. These sensors are a part of a feedback loop that operates to keep the levitated rotating parts of the bearing stable and centered. The resulting complexity means that active magnetic bearings are expensive, require periodic maintenance, and continuously consume electrical power to energize their amplifiers and their electromagnets.Passive magnetic bearings are, of course, also subject to the constraints imposed by Earnshaw’s Theorem but they solve this problem in a straightforward and simple way, with only “passive” elements that take advantage of a loophole implicit in the derivation of Earnshaw’s Theorem. This loophole is that Earnshaw’s Theorem as derived applies only to static systems, i.e. an assembly of stationary permanent magnets arranged so as to levitate an object containing other permanent magnets. The theorem can be overcome if dynamic effects are taken into account. In active magnetic bearings the “dynamic effects” involve the afore-mentioned sensors, amplifiers, and electromagnets."

Jan 1, 2012

By F. E. P. PEARSON

Sandstone quarried from an island in Lake Winnipeg is barged 130 km to a processing plant at Selkirk on the Red River. The stone is white, poorly consolidated, and consists of rounded quartz grains of high natural purity. It is an important supplier of silica in Western Canada for glass, fiberglass, foundry and other industrial uses.

Jan 1, 1984

By L. Chunpongtong

ABSTRACT The mining limit in oil sands is regulated by the ratio of total mining volume (ore, interburden, and overburden) one has to mine per volume of bitumen in place (TV/BIP). This paper presents a mathematical solution for creating the most economical pit outline where the TV/BIP ratio upper limit is 12, by combining mining economic theory and the Lerchs-Grossmann (LG) algorithm.

Jan 1, 2014

By L. Chunpongtong

The mining limit in oil sands is regulated by the ratio of total mining volume (ore, interburden, and overburden) one has to mine per volume of bitumen in place (TV/BIP). This paper presents a mathematical solution for creating the most economical pit outline where the TV/BIP ratio upper limit is 12, by combining mining economic theory and the Lerchs-Grossmann (LG) algorithm.

Jan 1, 2014

By M. J. Marinigh

Increased safety requirements, higher operational costs, greater environmental restrictions, and new competitive processing techniques are the challenges smelter operators must confront in order to remain economically viable. In converting furnaces which have tuyeres such as the Noranda Reactor and the Teniente, Peirce Smith and Hoboken converters, efficient tuyere line management is critical to optimizing blowing rates, increasing refractory life, and improving safety. This paper will describe recent improvements made to equipment used for tuyere punching, tuyere silencing, tuyere pyrometry and refractory drilling of tuyeres and how the proper application of the equipment can lead to operational and safety improvements.

Jan 1, 2007

By A. Michalkow

DELN ITE Mines Limited is located in Deloro township, on the west end of the south break of the Porcupine Camp. Mining operations are currently being carried out on the downward extension of a system of quartz veins in an andesite zone. This zone has been followed from surface to the present bottom level of 5,250 feet. The changing mineralogy of the vein system has involved an increase in tourmaline content from the surface downwards, so that the veins at the lower levels are composed of dark brown quartz-tourmaline. The drilling problem presented by these extremely hard veins was partially alleviated by the development and adoption of a one-inch drill bit. All blast-hole drilling is now done with the one-inch bit, without any difference in hole spacing.

Jan 1, 1962

By M. S. Diederichs, J. Oke

Surface limitations and a need for more direct transportation routes require serious consideration be given to the development of underground construction works in geotechnically unfavourable conditions. Due to geographical and logistical limitations, the construction of these underground works is restricted to difficult ground conditions that require temporary pre-support before excavation in order to avoid tunnel collapse or severe surface settlement. One type of pre-support is the umbrella arch system, which has been gaining popularity due to cost and time commitment in comparison with other pre-support systems (e.g., ground freezing). The umbrella arch system has been employed with significant frequency around the world, yet without a complete understanding about the mechanical response of the system. As such, literature has found the temporary support system to be both under and over designed with regard to safety and/or economical impact. The authors of this paper have made three major contributions to increase understanding of the umbrella arch system and to help optimize the design process. Firstly, the authors have developed nomenclature in order to categorize and define umbrella arch elements and systems, which also stimulated the creation of the empirically driven Umbrella Arch Selection Chart. Secondly, the authors have established a design methodology that is primarily based on advanced numerical modelling techniques to aid in the optimized design of the umbrella arch arrangement for site specific conditions. Thirdly, the authors have developed a semi-analytical model for umbrella arch systems employed in squeezing ground conditions by incorporating elastic foundation theory as well as convergence confinement theory. These three major contributions to such a widely employed tunnelling pre-support system will be introduced and explained in detail, and will include discussion of how each is incorporated in the complete tunnel support design process and throughout the construction and monitoring phase of a project.

Jan 1, 2015

By C. J. Havard, G. C. Taylor, D. G. Cook, N. C. Ollerenshaw, D. K. Norris

"The area encompassed by this report is the eastern and northern Cordillera, shown on the composite map accompanying these background papers. It extends from the 49th pm•allel to the Arctic Ocean and from the Rocky Mountain and Tintina trenches to the Interior Plains. The Mackenzie delta is included in the discussions because of the implications of the bedrock geology of the Arctic Plateau and Coastal Plain on the hydrocarbon and mineral potential beneath it.The eastern and northern Cordillera forms the back-bone of the Western Canada sedimentary basin and from it most of the principles of orogenesis and epeirogenesis relating to the understanding of the structural, depositional and fossil record of the basin have been derived. It may be divided roughly into two parts, reflecting basic differences not only in structural style but also in mineral potential. The more easterly and younger rocks generally contain hydro-carbons, coal and non-metallic minerals; the more westerly and older rocks contain metallic and industrial minerals."

Jan 1, 1970

By N. Wachgama, J. P. T. Kapusta, R. U. Pagador

The Thai Copper Industries smelter (Thai Copper) is located some 200 km southeast of Bangkok near the MapTaPhut deep sea port in one of the industrial centres of Thailand. Although construction of the complex started in the mid 1990s, the smelter, acid plant and refinery were completed in 2004. Thai Copper is a state-of-the-art copper smelter processing imported concentrates with a total yearly capacity of 165,000 tonnes of cathodes. It employs the El Teniente Technology where concentrates are blended and smelted continuously in a primary smelting reactor to produce high grade matte or white metal. The white metal is converted in batches to blister copper in Hoboken siphon converters equipped with Air Liquide Shrouded Injector (ALS I) Technology for sonic injection of oxygen enriched air. Final refining is carried out in two anode furnaces prior to anode casting and electrorefining. Thai Copper and Air Liquide Canada executed a technical assistance agreement in late 2005. Pre-commissioning of the shrouded injectors took place in July and November 2006 while hot commissioning occurred in December 2006. This paper presents the major technical aspects of the joint commissioning, including the establishment of operating practices specific to shrouded injection converting. Preliminary results of this first commercial implementation of ALSI Technology in copper converting are also provided.

Jan 1, 2007

By A Frydrychewicz, J. Mirza, J. Lipkowski

The objective of this work was to understand the mechanisms of action of additives, such as thiourea, that enhance gold leaching in thiosulfate solution. The leaching reaction and surface passivation were investigated using linear sweep voltammetry. Leaching currents were determined using analysis of current-potential curves and the mixed potential theory. The gold-electrolyte interface was further characterized with surface enhanced Raman spectroscopy. The results show how thiourea prevents formation of oxysulfur compounds, which passivate the gold surface. Other molecules such as 3- m ercaptopropionic acid and L-cysteine were also studied as possible additives to prevent passive layer formation.

Jan 1, 2011

By S. A. Briggs

Bioremediation has been accepted as a treatment technique for groundwater contamination in subsurface soils and shows promise for contaminated fractured rock environments. Biological growth in fractured rock is expected to occur predominantly as biofilms attach to the fracture surfaces. Biofilms in rock fractures are subject to a complex system of forces and other phenomenon due to the dynamics of the bulk fluid in which they grow. In this paper, through the applications of computational fluid dynamics (CFD) to rock fractures, where the boundaries are rough and the flow is complex, a precise analysis was conducted of the interaction of a fluid flow and the rock fracture. Specifically, hydraulic parameters and velocity profiles of an actual rock fracture were calculated and compared to a fracture of equivalent aperture. From the analysis it is clear that it is important to use more complex models such as the Lattice Boltzmann Method used is this paper to describe fracture flow.

May 1, 2009

By J. R. Giegerich

THE problem of dust control in metal mines has, of late years, received considerable attention. In 1932, a detailed study of dust conditions at the Sullivan mine was undertaken and, while there are no actual data available regarding conditions prior to that date, there has unquestionably been a great improvement as a result of the investigation and of the preventive methods adopted. In attacking the problem, three main factors were considered: first, and most important, how to prevent dust from being formed; second, how to depress or collect it if formed; and third-if unable to accomplish these-what precautionary measures must be adopted to prevent inhalation of this dust. Seven distinct methods of dust control are now practised at the Sullivan. Six of these are employed underground; they are tabulated below in the order of their relative importance. The seventh method is used in the crushing plants on the surface. (1) Improved ventilation (2) General use of water sprays and atomizers (3) Curtailment of secondary blasting during shift hours ( 4) 100 percent wet drilling-primary and secondary (5) Wearing of protective equipment (6) Change from carbide to electric lamps (7) Installation of dust collectors

Jan 1, 1936

By Narasimha Mangadoddy, Teja Reddy Vakamalla

"Vertical hydrocyclones are very common in most of the comminution circuits. Inclined cyclones are also found for specific mineral processing applications. In this work, Computational Fluid Dynamics (CFD) technique and experiments are used to find the reasons behind the inclinations effect on hydrocyclone performance characteristics. The water and silica slurry experiments are conducted with 75 mm hydrocyclone at different inclined positions (0-600) to the vertical plane. Corresponding two-phase numerical simulations are performed with Volume of Fluid (VOF) model coupled with Large Eddy Simulation (LES) turbulence model. Multiphase simulations are carried out with Algebraic Slip Mixture model modified with lift, drag forces and Newtonian rheology model corrected with fines for various feed solids concentration. A raise in the under flow solids percentage, cut diameter and a reduction in the water split is observed with the inclination. Electrical Resistance Tomography (ERT) and High Speed Video (HSV) data is used to cross validate the inclined cyclone’s CFD air-core and solids concentration data. Predicted efficiency curves are found in a close agreement with experiments for all the inclinations. Comparison of experimental and predicted flow data clearly follows trend with the literature. Key words: Hydrocyclone, CFD, ERT, inclination, water splitINTRODUCTIONHydrocyclones are devices used to separate or classify particles based on particle size difference in the water medium. Their usage is very wide in chemical, petroleum, mineral and bio industries due to its structural simplicity, high throughput, small volume, low cost and maintenance. Cyclone mainly consists of a cylindrical section followed by a conical section attached to a single feed inlet and two product outlets named vortex finder and spigot. It works on the principle of centrifugal sedimentation. The slurry is fed tangentially to the hydrocyclone, in which larger particles are moved towards the wall and separated by centrifugal forces to the underflow. Smaller size particles follow liquid due to drag forces to the overflow. With its simple structure, the flow behavior inside the hydrocyclone is quite complex. Vertical cyclones are common in practice in most of the comminution circuits. Horizontal cyclones can be found in extreme cases which are for installation convenience rather than for process reasons. Inclined cyclones are also present for specific mineral processing applications. In coal preparation plants, dense medium cyclones are operated near to horizontal inclination of 20 degrees to allow large spigot sizes for sinks removal, self-drain of contents during shutdown. In the phosphate removal, dense medium cyclones are inclined with an angle between 0-90 degrees for better separation of ore and tailings (Liu Feng et al., 2006). Even in the clusters, hydrocyclones are mounted with an inclination around the feed distributor for uniform distribution of slurry and under flow collection. It is believed in mineral processing industry that inclined cyclones would fetch the benefit in number of ways while classifying the material by size. Gravity influences the cyclone performance through the air core size and position variations in large cyclones. It also favours the cyclone operation at coarser cut points without varying any other design and operating parameters. Minimizing fines misplacement to underflow can be achieved with inclination."

Jan 1, 2016