Search Documents

By Richard Cyr, Peter Larsen, William Quesnel

"The need to continually improve efficiency and lower costs in mining operations is of paramount importance to all concerned in the industry. Mining operations are constantly testing new methods and equipment in order to lower costs and improve productivity. Equipment suppliers strive to fulfill the demands of the mines through improved design and innovative ideas for productivity increases. In some cases, however, an increase in productivity does not require new equipment design, but rather the application of an existing mining method into different operating parameters. Such is the case in applying longhole methods to narrow vein ore deposits.Bulk mining methods have long been recognized as efficient, low-cost alternatives in narrow vein operations. Typically, shrinkage and some cut-and-fill methods are employed. The shortfall of these methods is the tendency to be labour intensive. The demand for miners skilled in these methods far outweighs their availability. Consequently, labour-efficient methods have to be employed to fill the void. The application of longhole drilling techniques to narrow vein deposits is one such method.IntroductionPercussion longhole drilling evolved in Canada in the early 1940s. Prior to percussion drilling, blast holes were drilled using diamond drill equipment. Jack Gardner, of Gardner Steel, began testing with carbide percussion bits and extension drill steel in applications where diamond drills had been previously employed. Percussion drilling equipment proved to be considerably more productive and cost-efficient. The experiment eventually led to the replacement of diamond drills in this application.Over the years, the percussion methods were improved, with particular emphasis on the equipment used. Rifle bar rotation machines evolved to independent rotation. Bar and arm set ups evolved into self-contained mobile drill carriers that increased productivity while reducing the physical labour. The introduction of hydraulics further improved efficiency and production figures. Today, it is not uncommon to see fully computerized jumbos in production longhole drilling applications. These machines represent the ""state-of-the-art"" in longhole drilling equipment.Production longhole drilling is considered to be one of the most efficient bulk mining methods in use today. Production statistics normally exhibit low-cost, efficient ore extraction. As a rule, longhole (blasthole) methods are associated with substantial ore deposits. These methods have exhibited high production figures and low mining costs.Over the past decade, long hole methods have been applied to several narrow vein deposits. These applications have proven that, given the right parameters, longhole methods will produce the same advantages in narrow vein deposits as are seen in more conventional applications."

Jan 1, 1990

By Russell A. Luke

"Modular Mining's computerized LHD position monitoring and dispatching system commenced operation at the De Beers Finsch Mine in mid- J99J. A sophisticated blend of proven and new technologies links the dispatcher at the workstation console on the surface with the LHD operators several hundred metres below. The dispatcher allocates each LHD to a priority tip and loading drive based on instructions provided by the miners and shift bosses underground. LHD operators receive tip and loading drive allocations on the vehicle computer console which communicates data via a Leaky Feeder radio network. The operators interact with the console to notify the dispatcher of delays, breakdowns, and changes in tip and tunnel status. The underground terminal displays allow shift bosses to monitor the progress of the LHDs as they pass infrared beacons (IRs) located in the tips loading drives and rim tunnel main haulage ways. The terminals also provide on-line statistics for the current and previous shifts. Future enhancements include optimized dispatching and interfacing to a PLC system controlling ventilation. Further, token ring-based loop UHF radios are being investigated as an alternative to the Leaky Feeder data radio network. IntroductionFinsch first contacted Modular about an LHD monitoring and dispatching system in late 1988. At that time, Modular declined a request for a formal quotation but agreed to perform an engineering feasibility study. The study was issued in mid-1989 and confirmed Finsch's belief that an underground system could be developed with technology available at that time. A contract for the system was signed the following year and, in May of 1991, the system began operation. By the end of 1991, LHDs on both production levels of the mine were under the control of the system."

Jan 1, 1993

By Tom Setterfield

Monster Copper Resources ?Junior focused solely on IOCG deposits ?Founded by ex-WMC geoscientists ?Properties in Brazil, Wernecke Breccias (Yukon), Central Mineral Belt and Nova Scotia Nova Scotia ?JV with Wallbridge Mining Company ?Ongoing Story ?Presented as a case study in generation and implementation of IOCG exploration program

Apr 1, 2005

By J. P. Sims

Abstract - Ultramafic to mafic igneous intrusions of the Las Aguilas district form part of a belt of generally mafic plutonic bodies within medium- and high-grade early Paleozoic metamorphic rocks in the southern Sierras Pampeanas region, Province of San Luis. The intrusions host the largest known nickel sulfide resource in Argentina and contain significant Cu, Co and PGE mineralization (2.2 Mt at 0.5% Ni, 0.5% Cu, 0.035% Co). Sulfides at Las Aguilas Este, one of two principal mineralized zones, are hosted by a body comprising subvertically dipping units of predominantly orthopyroxenite and melanorite cumulate, with lesser dunite, harzburgite, norite, leuconorite, and amphibolite. The units are zoned horizontally from ultramafic to mafic compositions, representing primary magmatic zonation away from an original base or side of the intrusion. Intercumulus nettextured and disseminated aggregates of pyrrhotite-chalcopyrite-pentlandite are concentrated in the peridotitic zones and extend into melanorite. Whole rock major and trace element compositions, and olivine chemistry, indicate that the parent magma was gabbroic/basaltic with 100 (Mg/Mg+Fe) near 59, and resembles tholeiitic magmas generated in subduction-related arc, or back-arc settings. Unusually aluminous Cr-bearing spinel is compositionally similar to those in some synorogenic mafic/ultramafic plutons in magmatic arc settings. Relatively Ni-depleted olivines and low Cu/Pd ratios are indicative of magmatic sulfide segregation early in the crystallization of the magma. Early orthopyroxene saturation and virtual lack of clinopyroxene, in conjunction with sulfur isotope values up to +6.6 ‰, spinel compositions, and presence of graphite, phlogopite and magmatic hornblende, all attest to probable crustal contamination of the parent magma. Assimilation of crustal sulfur may have been crucial in the early attainment of sulfide saturation and resultant formation of magmatic Ni-Cu sulfide mineralization. Fabrics, textures and mineralogy of the intrusions and country rocks and U-Pb zircon dating indicate syntectonic-synmetamorphic emplacement at 478±6 Ma during the Famatinian (Ordovician) orogeny. Minor to locally significant recrystallization and deformation of mafic-ultramafic rocks and redistribution of sulfides and PGE occurred during and following the Famatinian orogeny. The Las Aguilas intrusion is one of several tholeiitic mafic-ultramafic intrusive complexes within an Ordovician arc - back-arc system in the Sierras Pampeanas. Aeromagnetic datasets and regional mapping suggest there is further potential for intrusion-hosted Ni-Cu mineralization along this eroded magmatic arc.

Jan 1, 1999

By T. R. Eger

The Load-Haul-Dump (LHD) vehicle is a trackless, free-steered vehicle used in underground hardrock mining to move large quantities of ore/rock to haulage trucks, ore dump locations, or crushing stations. The purpose of this paper is to show, through case study examples, how principles of human factors can be applied to improve the overall design of the LHD vehicle to enhance line-of-sight (LOS), improve posture and decrease whole-body vibration exposure (WBV). Vehicle modifications (larger cab windows, lower engine profile, smaller buckets, angled radiator profile) can lead to improved line-of-sight. The use of secondary viewing devices, such as cameras, can also improve line-of-sight and allow the operator to adopt a more neutral sitting posture. Seating systems that are suited to the underground mining environment can result in vibration attenuation and less vibration transmitted to the LHD operator. The connection between vehicle design, line-of-sight and driving posture needs to be considered in order to continue to improve the design of the LHD and enable the operator to work in a neutral posture with minimal vibration exposure. Changes leading to improved line-of-sight, vibration reduction, and a neutral sitting posture will lead to fewer LOS related accidents and decreased risk factors for musculoskeletal injury.

Aug 1, 2013

By M. Fiset, D. Belley

"In a country with a cold climate like Canada, the cost of replacing worn parts of snowplow equipment such as blades, is enormous. A great number of these blades, with different mechanical properties, are available, but few studies have been made to facilitate their selection according to the optimum ratio of wear resistance to cost. To attain this objective, laboratory tests have been developed to correlate test results with those obtained from various road service conditions. The test materials, 1080steel in different states, 1090steel and D2 tool steel were chosen to cover a large range of hardness as well as different microstructures. Comparison of the wear resistance of the test materials relative to a standard revealed, in general, a good correlation between the results of laboratory cement wheel tests and those from the road tests. Scanning electron microscope wear scars of laboratory and road test specimens were compared to determine if similar removal material mechanisms were active. IntroductionThe correlation between wear tests in service and those performed with the aid of laboratory equipment is of considerable interest. As a matter of fact, when correlation exists, it allows one to evaluate the performance of a material more easily and at a lesser cost.Several authors have been interested in simulating various wear circumstances, especially abrasive wear. In particular, the simulation of wear on implements working the soil, has been tried by several researchers. The test using the rubber wheel seems to be the one giving the best correlation if the soil is rather sandy and its moisture content is low.However, little work has been done concerning wear on the plates, skids and blades attached to trucks used for levelling and snowplowing; such equipment being used to keep roads clear in northern countries. Now each year, companies introduce new steels by claiming that the y are superior in performance to their predecessor s and invariably they demand a higher cost. The study presented here was undertaken with the goal of making a more judicious choice of these steels by simulating their behaviour in the laboratory. Moreover, the examination of abraded surfaces in situ and in the laboratory have also allowed us to compare the respective wear mechanisms."

Jan 1, 1988

By G. Kachaniwsky, M. Bédard

"The Noranda Continuous Smelting Process at the Home smelter was commissioned in March 1973. The ability of the process to handle a wide variety of feed materials and a steady stream of technical innovations in recent decades has served to maintain the Home as an efficient and versatile custom smelter. This paper reviews recent technological development and capabilities in areas such as sampling and preparation of secondary and complex materials, as well as the smelting and related environmental control issues. Future trends and improvements are also addressed.IntroductionThe Noranda Home smelter commenced operations in 1927. It was originally designed to treat 910 tonnes per day of copper concentrates and ores coming from the new Home mine site. In the 19305, the company opened its doors to other mines in northwestern Quebec. Treatment of feed materials on a custom basis has, therefore, always been an important factor in the operation of the Home smelter. Throughout the years, the Home gradually increased its custom smelting capacity, while maintaining its production from the Home mine. By the early 1950s, 65% of the materials processed was from outside customers, and by 1974, this figure had increased to more than 85% . With the closure of the Home mine in 1976, the company extended its smelting operations beyond ore and concentrate, and began to treat more scrap metals and residues rich in copper and precious metal content.Corresponding with the ever-changing pattern of feed sources, the Home smelter has adopted technological improvements to meet new and challenging business conditions. The technology of the original smelter of 1927has been completely replaced over the years in the quest for improvement. One of these major changes occurred in 1973 with the start-up of the Noranda Process Reactor. This extremely efficient smelting system has been exploited to treat a wide variety of copper and precious metal (PM) containing custom materials. This paper reviews recent developments and improvements achieved at the Home smelter, in the receiving, sampling and treatments of copper and PM scrap and secondaries, with particular emphasis on the development of new technology and equipment in complex feed materials treatment."

Jan 1, 1991

By William Petruk, Donald Leroux, Michael Cooper

"Brunswick's primary flotation circuit (CuPb) produces a low grade concentrate containing considerable amounts of undesirable sphalerite and pyrite. To determine the cause of the poor selectivity, a series of Quantitative Mineralogical Analyses (QMA) were performed on several CuPb circuit streams. It was observed that significant fractions of sphalerite and pyrite reporting to the concentrate was liberated, meaning that their depression was not complete. The study highlighted the need for some R&D efforts to be spent in sulphide flotation fundamentals.IntroductionThe viability of many mining projects strongly depends on the performance of their concentrators. More than ever, competitive grade concentrate and high metal recoveries are criteria of paramount economic importance. The selectivity of solid/solid separation processes used in concentrators must be maintained at high levels or continuously improved.Flotation is the solid/solid separation process used by most base metal producers. In spite of its low operating cost, flotation remains a very complex process. To make it selective, precise reagent dosages and electrochemical conditions must be maintained. The difficulty in controlling flotation lies in the numerous heterogeneous reactions that can take place between the different solid, liquid and gaseous phases involved. This complex chemistry makes flotation selectivity difficult to understand and, therefore, to improve from a theoretical point of view.Brunswick Mining and Smelting, near Bathurst N.B., operates a 10500 tpd concentrator which produces four concentrates through five stages of sequential flotation (Figure I). Various reagents are added at key process stages while the ore undergoes different electrochemical conditions. Although the selectivity is important at all stages, the performance of the very first separation, the CuPb circuit, is the most critical. It is here where mineral misplacement to the wrong stream has the greatest economic consequences."

Jan 1, 1996

By S. A. Vazhnov, A. G. Kalimov, A. A. Potienko

In this paper we describe a mathematical model of the magnetic field and magnetohydrodynamic processes simulation in aluminum reduction cells developed in St. Petersburg State Polytechnic University, Russia. The model includes: (a) calculation of the currents in the busbar system and inside the aluminum cell construction elements including cathode and anode structures, aluminum and electrolyte layers; (b) magnetic field simulation using the integral equation method; ( c) investigation of the magnetohydrodynamic characteristics on the basis of a shallow-water approach. The developed model was used to investigate operational characteristics of the different industrial aluminum cells. Calculated magnetic field distributions and MHD stability parameters were compared with the available experimental information; the comparison demonstrated a reasonably good agreement.

Jan 1, 2006

The recovery of fine hydrophilic gangue in flotation is related to the recovery of water. Water is carried by bubbles as a film and wake into the froth. The amount carried (entrained) depends on bubble size, gas rate and the subject of this paper, frother type. To isolate the effect of frother type from that of bubble size and gas rate, gas holdup is used as the correlating variable. Measurements were made using a bubble column (no solids) operated continuously with the overflow recycled. Continuous operation meant some foam depth was required to ensure only entrained water is recovered. Using an automatically controlled 7cm foam depth the overflow rate of water is used as a measure of 'water carrying rate'. It is shown that the common frothers can be grouped into four families based on the water carrying rate-gas holdup relationship.

Jan 1, 2006

By C. Juers

Laboratory chromate coating was applied on AM50 and AZ91D alloys and compared to phosphate-permanganate one. Evaluation of the corrosion behaviour was performed using electrochemical DC and AC methods in ASTM water D1384-87. This electrolyte was chosen because it was moderately aggressive and found to give generally good correlations with long period exposure results in atmospheric conditions. Electrochemical impedance spectroscopy was used to determine more accurately the corrosion rates from the analyses of the high frequency capacitive loop. Anodic polarization was applied in order to evaluate the pitting resistance of the different coatings. These results were correlated with weight loss data evaluated from experiments performed by immersion tests in ASTM water D1384-87 and climatic cyclic chamber tests.

Jan 1, 2006

By Anna Szostak-Chrzanowski, Adam Chrzanowski

"New techniques in monitoring surveys and new methods in the analysis and prediction of ground subsidence are being developed in the Department of Surveying Engineering at the University of New Brunswick (UNB). The new surveying techniques include a telemetry monitoring system developed at UNB in cooperation with CANMET, and use of the satellite Global Positioning System. A generalized approach to the analysis of deformation surveys has been developed which permits an integrated analysis of geodetic and geotechnical measurements in geometrical modelling of ground subsidence. A computer program, FEMMA, has been developed for the elastic and non-linear elastic analysis and the deterministic prediction of deformations using the finite element method.IntroductionResearch and development of new monitoring techniques and new methods in the analysis and prediction of ground subsidence in mining areas is an integral part of a broad research program on deformation surveys which is being carried out in the Department of Surveying Engineering at the University of New Brunswick.The research concentrates on:developmentof a general method for predicting deformations with an emphasis on the use of the non-linear elastic finite element analysis; development of a generalized approach to the geometrical analysis of deformation surveys with an integration of geodetic and geotechnical measurements; and development of new monitoring techniques with an emphasis on continuous data acquisition and application of new space techniques such as the satellite Global Positioning System (GPS).This paper gives a brief report on the progress and recent developments within the above program."

Jan 1, 1987

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters ? usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

By G. Shen, W. R. Tyson

In most fracture toughness test standards, such as ASTM E 1290 and BS 7448, crack-tip opening displacement (CTOD) is measured by using three-point bend (SE(B)) or compact (C(T)) samples with deep cracks. The loading mode and crack depth in these tests sometimes are different from that of pipelines. Pipelines usually have shallow defects and experience tensile loading when the supporting ground moves. As a result, the CTOD measured by these samples is lower than that of pipeline in tension. Recent researches suggest using single-edge-notch tension (SE(T)) samples to measure fracture toughness for pipelines. In the present study, shallow and deep SE(T) samples under fixed grip loading were analyzed by using the finite element technique. An equation to relate the CTOD to the area of the load/plastic crack mouth opening displacement (CMOD) is proposed. With this equation, the CTOD of a SE(T) sample can be evaluated by measuring the area under the load/plastic CMOD curve of a SE(T) sample.

Jan 1, 2005

By Jacques H. Nantel, James F. Archibald

"Frozen tailings material may be required, in the future, to perform the support functions of underground backfill in mines located in zones of permafrost, notably in the high Arctic. To date, no knowledge of physical support parameters of such materials has been obtained in Canada due to the limited mining activity in permafrost regions. It is therefore judged essential that the important physical and mechanical properties relating to frozen tailings material be assessed.Innovative mining methods will be required to cope with the harsh environmental conditions that exist at mining sites in the Canadian Arctic. A preliminary laboratory study, in the absence of field trials at limited Arctic mining sites, has been completed in which the physical and mechanical properties of several types of representative mill tailings mixtures have been investigated. A variety of tests, to determine frozen slurry and pelletized tailings strength properties, moduli of compression, optimum water contents, deformation characteristics and the like, have been conducted.The results of this study will be used to establish guidelines for the suitability of tailings use in such northern mining environments. IntroductionFrozen tailings material has never been used to backfill underground openings in Canadian mines. At present only one Canadian mine, the Polaris Mine situated on Little Cornwallis Island, is investigating the use of frozen backfill. However, the Canadian North covers a large territory and potentially contains a large number of mineral deposits. The understanding of concepts related to mining activities in sub-zero frozen ground is therefore important.The implications of using frozen tailings as underground backfill material are far reaching both from the point of view of mine stability and disposal of tailings in the arctic regions.The strength of frozen materials (soil, backfill, etc.) may take on different meaning depending on the engineering situation. Both the concepts of rupture and excessive deformation need to be considered.The functions usually required to be performed by the backfill material in underground mines may be summarized asfollows:a) working floors; such as in cut-and-fill stopesb) stope wall support; for cut-and-fill and delayed fill stope~c) self-support when backfill is exposed on one face; during pillar recovery phases.For fill functions such as working floors, the short-term response of the frozen fill is the dominant concern. For the other fill functions, the long-term deformation response of the frozen fill, or creep, is of interest."

Jan 1, 1986

By A. Ismail

"The paper takes its material from three peat mining and power project feasibility studies sponsored by CANMET and conducted by Montreal Engineering Company Ltd. in the years 1976 to 1980. The role which peat may play in the Canadian energy prospectus is outlined, estimated and measured fuel peat resources are tabulated, and the economic and technical feasibility of mining peat for power generation is reviewed Recommendations are made for future work, and construction and disbursement schedules are developed for a combined peat mining and power generation project. The relationship between the mining of moss and fuel peat is discussed.IntroductionWhereas moss peat has long been produced in Canada, and exported for horticultural use , the underlying fuel peat has received little attention until fairly recently.In the seventies, however, the deepening oil crisis spurred Canadian interest in Irish, Finnish and Russian experiences in the utilization of fuel peat. Among others, Energy, Mines and Resources Canada had long been alive to the possibilities which indigenous peat offers, and in 1976 the Canada Centre for Mineral and Energy Technology (CANMET encouraged a proposal from Monenco to carry out a preliminary study and submit a report on the "" Assessment of Canadian Peat as an Alternative Fuel for Power Generation"". The report was submitted in April 1977. This was the first of a series of studies, and the authors of this paper were involved in its preparation.The escalating price of oil and the increasing problem of relying on its availability have combined to make alternative fuels more attractive. Peat, like other fuels previously uneconomic because oil was cheap, is now progressively gaining in viability. In addition to these factors, the utilization of peat has the following advantages: improvement in the country's balance of payments, by virtue of burning an indigenous fuel;creation of local employment for the mining of peat; improvement in land utilization;peat is a relatively clean-burning fuel, with low sulphur and ash contents."

Jan 1, 1980

By R. Phillips, A. G. Doll, D. J. Barratt

"The Bond low energy impact (crushing) work index test is specified to be performed on rock specimens between 50 mm and 75 mm in effective diameter. NQ-diameter drill core, frequently used in mineral exploration programs does not meet that specification, it being 45 mm diameter or less.This paper reports the effect of performing the impact test on contiguous sections of HQ diameter and NQ diameter core, exploring the hypothesis that the contiguous intervals give equivalent results in spite of the core diameter difference."

Jan 1, 2012

By P. Gautier

Current feedstock in the aluminum hot forging processes can be used in the cast or extruded forms. The microstructural variation between as-cast and extruded materials could result in different mechanical properties and corrosion resistance for hot-forged products. Corrosion performances were examined for forged parts produced by two AA6082 feedstocks at different conditions using the following corrosion tests: open circuit potential, anodic polarization, salt spray exposure and corrosion fatigue. With the help of optical and scanning electron microscopes, metallographical investigations were carried out on cast-forged and extruded-forged materials before and after corrosion. The corrosion behavior of both materials was compared in both as-forged and aged tempers. Results show that there is no significant difference in the corrosion performance for final cast-forged and extruded-forged products.

Jan 1, 2011

By J. C. Li, Y. Zou, L. He

"The effect of rock joints is significant in characterizing dynamic behaviors of discontinuous rock masses. To reveal the relation between the transmission coefficient and the contact situation of the joint surface, an experimental study on stress wave propagation across an artificial rock joint was carried out using a modified Split Hopkinson Pressure Bar (SHPB) apparatus. All the bars and specimens were norite cored from the same site, and one surface of the specimen which contacted to the transmitted bar was sawn with a number of notches to simulate the artificial rough joint. According to a wave separation method, two strain gauges were mounted on each pressure bar at a specific spacing, then the incident, reflected and transmitted waves across the joints were obtained from the test data. It was found that the contact situation of the rock joint surface makes a different on the wave propagation. Finally comparisons of the transmission coefficients with different contact area ratios and different joint thicknesses were made respectively. The results show the effects of contact area ratio and thickness of joints on wave transmission.INTRODUCTIONJoints affect the dynamic mechanical behaviors of the rock masses significantly. When propagates across the rock masses, wave usually attenuates in amplitude and frequency due to the presence of the joint as a discontinuous interface in the rock masses. Rock joints are the main factor that affects the behaviors and properties of rock masses. Many researchers have focused on the mechanical properties of rock joints under quasi-static conditions. Nowadays, the effect of joint dynamic properties on wave propagation across rock masses is gradually taken into account in theoretical and numerical studies.The effective contact area, joint roughness, and properties of the asperities and filling materials have been found to influence the normal stiffness of joints (Bandis et al. 1983). As suggested by the International Society for Rock Mechanics (ISRM), the roughness of the discontinuities can be generally characterized by large-scale “waviness” and small-scale “unevenness” (Brown 1981). Many researchers focused on the roughness of rock joints that affects the mechanical properties of rock masses and wave propagation. For example, Brown and Scholz (1985, 1986) presented theoretically and verified experimentally a closure model of contact between two random nominally flat elastic surfaces, which showed that the joint closure property depended both on the surface topography and material properties. Pyrak-Nolte et al. (1997) presented the quantitative aperture data for three-dimensional interconnected fracture networks, which were imbedded in intact opaque rock samples several centimeters in length, using x-ray computerized tomographic (CT) imaging. Fardin et al. (2001) systematically investigated the effect of scale on the surface roughness of rock joints and concluded that samples should be equal to or larger than the stationary limit for surface roughness to be accurately characterized on a laboratory scale or in the field. Zhao et al. (2006) conducted excellent ultrasonic tests across intact cement mortar specimens, singlefracture specimens, and two-fracture specimens."

Jan 1, 2015

By Y. Nishida, Y. Nara, T. Ishida

Understanding time-dependent deformation and fracturing in rock is essential, because the information of the long-term stability of rock is required for many sub-surface structures excavated in a rock mass. Time-dependent fracture propagation has been invoked as a potential key mechanism responsible for the increase in seismicity preceding earthquake ruptures. In engineering projects and in preventing natural hazards, the study of time-dependent fracturing is necessary. Subcritical crack growth is one of the main causes of time-dependent fracturing in rock. For silicate rocks, subcritical crack growth has been investigated by various researchers. It has been clarified that surrounding environmental conditions (temperature, humidity, and existence of water) have strong influence on subcritical crack growth in silicate rocks. Therefore, the information of subcritical crack growth in silicate rocks has already been enough. On the other hand, information of subcritical crack growth in carbonate rocks is not enough. Especially, the influence of surrounding environment on subcritical crack growth in carbonate rock has not been clarified yet. In this study, we investigate subcritical crack growth in carbonate rock experimentally using a fracture mechanics testing method. Marble obtained in Skopje in Macedonia is used as a carbonate rock sample. The Double Torsion method is used to measure the crack velocity and stress intensity factor. Especially, influence of water on subcritical crack growth in Macedonian marble is investigated. It was shown that the crack velocity in water is much higher than that in air at the same temperature. Based on the results of subcritical crack growth measurements, the long-term strength is evaluated for marble. It was clarified that the long-term strength in water is lower than that in air in marble. It is concluded that water has a remarkable influence on subcritical crack growth in marble. It is also considered that the long-term stability of carbonate rock masses should be ensured in a dry environment.

Jan 1, 2015