Search Documents

By A. P. Bois, K. Saleh, A. Ghorbal, V. Hajiabdolmajid, G. Ballivy

"The knowledge of the initial stress field is not always sufficient to ensure the stability of mining stopes due to the high-stress variations generated by mining. Monitoring of these openings is then necessary and can provide quantitative information (deformations and stress variations) as well as qualitative information (state of stability).An applied technique for following the variations of stress and deformation in static and dynamic conditions, in relation to the evaluation of the stability of underground openings known as “Cylindre Instrumenté de l’Université de Sherbrooke” (CIUS) is discussed in this paper. In addition, a data acquisition system combined with a rock failure warning system has been developed to be connected to the CIUS for detecting the instabilities, which can endanger the stability of underground openings. Also, the installation of six CIUS and a data acquisition system as well as the selected procedure of programming in a warning system are briefly described."

Jan 1, 2003

By Murray Wood, Michael Schaffer, Makat Katom

"An expert system applied to the control of mineral process unit operations is, by its nature, the site best operating practice, having been designed by the local experts in conjunction with consulting metallurgists. The “common sense” layer in a MET (MinnovEX Expert Technology) solution determines an appropriate action for the current operating conditions through a developed heuristic model of the process (expert system). The magnitude of the setpoint change that is made is proportional to the confidence that the system has in its interpretation of the current conditions (fuzzy logic). The solution is always striving to take the process to a constraint and thereby optimise the operation. An accepted limitation of the solution is that the only way the system can determine if a constraint has been reached is to exceed it and then withdraw – essentially “experimenting” with the process. By leveraging a model, which can accurately ""simulate"" the process, this restriction can be circumvented by pre-testing the set point change through a ""what if"" analysis and then modifying the solution as appropriate.At Ok Tedi, the introduction in 1999 of a MET expert system for SAG milling resulted in significant improvement in circuit throughput. Yet, with the additional inclusion of an accurate model of the process there was still more that could be achieved. Hence, in 2002 a MET Neural Network model was developed and deployed to enhance the existing expert system solution. The principal objective of this model was predicting the effect that changes in SAG tonnage and density would have on the power draw of the mill - essentially a power predictor. The results have seen a decrease in process variance with an associated increase in average circuit performance.This paper describes the methodology by which the Neural Network model was implemented, the considerations and limitations when applying this technology and ultimately the results that were achieved."

Jan 1, 2003

By Donald Leroux, Dave Scott, Giovanni Di Prisco

"The Lady Loretta lead-zinc deposit in Northwest Queensland, Australia contains an average of 5.9% lead, 17.1% zinc and 97 g/t silver. Ore mineralization is mostly comprised of fairly complex intergrowths of pyrite, sphalerite and galena. Starting in 1998, Noranda Inc., the major joint venture partner of the project, conducted extensive metallurgical test work, which culminated in July - August 2000 in a series of Pilot Plant tests. A common thread to all the metallurgical work has been the deportment of a large portion of silver into non-payable metallurgical products. Average silver distribution from four Pilot Plants shows a distribution of silver in lead concentrate of 28%, whereas silver in zinc concentrate was 49%, and 23% in the final tails.The consistently poor silver recovery as well as the fairly unusual silver distribution, particularly in zinc concentrate, was considered an issue to be thoroughly investigated. A mineralogical plan was devised to determine if these particular metallurgical results were somewhat related to the nature and mode of occurrence of silver carriers. Work was performed to determine discrete silver-bearing minerals and/or silver contained in solid solution in a suite of commonly occurring sulphides. Ore microscopy, SEM methods, Electron Microprobe and Ion Microprobe analyses were all used to answer these questions, and to find the silver carriers, so a metallurgical plan could be devised to improve silver recovery.INTRODUCTIONPotential economic exploitation of the Lady Loretta deposit in Queensland, Australia is driven by revenue derived from zinc and lead flotation concentrates and co-product silver recovery in lead. Relatively low recoveries of payable silver to lead concentrate, and high silver distribution to zinc concentrate necessitated an investigation into the natu"

Jan 1, 2002

By Carl Bertrand, Patrice Nadeau, Claude Bazin

"Rio Tinto Fer et Titane processes the ore extracted from the Lac Tio orebody to concentrate the hemo-ilmenite (FeO.TiO2-Fe2O3) mineral that is subsequently smelted to produce pig iron and titanium oxide slag. The ore is crushed, heat treated (roasted) and concentrated using dry magnetic separators. This paper describes a model to predict the magnetic susceptibility of the roasted ore and its behaviour in the magnetic separation plant. The model uses a classification of the ore as a function of the size and magnetic susceptibility of the particles. A subsequent division into mineral species allows the simulation of the magnetic separation process. The model is used to assess various operating options when process disturbances occur.INTRODUCTIONOre processing operations consist of ore size reduction followed by the recovery of valuable species in a concentrate that is subsequently sold for its minerals or metal content. The concentration processes are based on the physical and/or chemical properties of the minerals contained in the ore. Flotation is typically used to recover minerals of base metals such as copper, zinc, lead or nickel. Iron ore and other dense minerals are typically concentrated by gravity separation processes. Magnetic separation uses the magnetic properties of the minerals to concentrate magnetite and other minerals, to clean coal concentrate and to recycle ferrosilicon for dense separation processes (Brophy, 1985).Magnetic separators can be divided into low and high intensity separators and high gradient magnetic separators (Gillet, 2008). Most of the low gradient magnetic separators are built as rotary drums that are operated in wet or dry conditions. Dry magnetic drum separators are used by Rio Tinto Fer et Titane in Sorel-Tracy, Canada to concentrate hemo-ilmenite from the ore extracted at the Lac Tio Lake mine near Havre St-Pierre, Canada. The analysis of production data suggests that process improvement could be achieved by identifying key variables for the control of the magnetic separation circuit and/or by modification to the circuit flowsheet. The use of a process model was considered to be an effective approach to conduct a preliminary analysis of the circuit with a view toward process optimization. However, the literature contains few detailed studies dealing with the modelling of magnetic separation processes."

Jan 1, 2011

By Jessica Egan, Daniel Hodouin, Mohammed Reza Khalezi, Steve Bellec, Claude Bazin, Carl Duchesne

"A model for gold leaching was developed and implemented into a simulator. The simulator uses a description of the ore that is based on the mineral composition and precious metal content. The model accounts for the distribution of minerals and precious metals through the size intervals. An ore texture model based on precious metals and minerals grain sizes within the ore is used to predict the exposed surface of the species in the various size intervals. A model is proposed to predict the rate of dissolution of any species dissolution using the exposed surface, particle size, cyanide and oxygen concentrations, temperature, pH and agitation. The flow of slurry through a leaching tank is modelled using a parallel arrangement of perfect mixers to simulate a bypass and a Cholette-Cloutier mixer model. The simulator can be used for circuit optimization but was developed to provide an environment for learning the basic concepts of process analysis methods. Examples are given to illustrate the application of the simulator for planning tracer tests and sampling campaigns.INTRODUCTIONThe constant pressure to improve the operation of processes that are already close to optimum imposes to plant engineers to be aware of the available process analysis tools and to be able to use them to assess process operation and make a diagnosis to possible problems. Some of these tools are:•,Sampling the streams of a process;•,Data reconciliation;•,Analysis of mixing in reactors;•,Estimation of rate parameters;•,Optimal tuning and flow sheet modification;•,Automatic control and real time optimization.Although some of these tools are part of the curriculum of many university engineering programs, the students are not exposed to actual process analysis problems. In addition the complexity of the ore dressing processes compounded with unavoidable measurement errors and plant disturbances can discourage many motivated engineers. These factors often lead to an incomplete valorization of the collected data and a poor return on the investment associated with the sampling, testing and analysis of the samples.Simulators are readily available for process optimization (Yalcin and Shang, 2006) by allowing:•,The simulation of various flow sheet configurations;•,The simulation of a change of operating conditions;•,The simulation of various control strategies;•,The training of plant operators.However few simulators have been developed with the objective of providing an environment for training plant engineers and technicians to the use of tools for process analysis and optimisation."

Jan 1, 2008

By Andy Fortin, Jeet Basi, Simon Hille

Goldcorp’s Eleonore mine is situated in Ell Lake area in the northeastern part of the Opinaca reservoir in the James Bay region of Quebec. The design of the 7000 t/d process plant includes crushing, grinding, bulk sulphide flotation, separate concentrate and tails leaching and detoxification circuits and residue handling. Detoxified flotation tails are thickened and filtered. A portion of the filtered tails are blended with the thickened detoxified sulphide concentration for paste backfill. The remaining filtered tails are trucked to the waste management facility. This presentation will describe the challenges faced with the commissioning and subsequent ramp-up of the flotation tails filter plant and the successes achieved by the multi-discipline team at Eleonore.

Jan 1, 2016

By K. B. Hodgins, P. Ouellette

"The North American mining industry faces challenging emissions regulations in the coming years with the introduction of new standards for off-road diesel engines. In order to remain competitive, industry stakeholders must invest in new technologies that are economically and environmentally sustainable.Westport Innovations Inc., Vancouver,British Columbia, has developed high-pressure direct injection (HPDI) technology that allows diesel engines to run primarily on natural gas with no intrusive engine modifications while reducing emissions of nitrous oxides (NOx), particulate matter (PM), and CO2 with no loss in performance. This is accomplished through late-cycle, high-pressure direct injection of natural gas into a diesel engine combustion chamber at the end of the compression stroke. A small amount of diesel fuel is injected first to initiate combustion, followed by the natural gas fuel main injection. The diesel cycle and its operating characteristics are fully retained including high combustion efficiency, lowspeed torque, high-power output, no engine knock, and fast response to load changes. Natural gas has not been an attractive fuel alternative in mining operations due to the reduced performance associated with spark ignition engines and the added weight and space required for compressed natural gas tanks. However, liquefied natural gas (LNG) can be stored with less impact on weight and space than compressed natural gas (CNG) by virtue of its increased energy density over CNG.Westport has applied HPDI technology to the Cummins QSK series engines for high horsepower applications such as power generation and mine haul trucking. HPDI can also be applied to other engine manufacturer platforms and market applications. Westport is interested in demonstrating the unique characteristics of HPDI in mine haul trucks to show diesel performance with low emissions levels using low-cost LNG fuel.Retrofitting a Tier 1 engine with HPDI would provide emissions reductions below the EPA 2006 Tier 2 standards while maintaining the performance and efficiency of the Tier 1 platform. The longer-term target is the Blue Sky voluntary standards of 3.8 g/kW-hr (2.8 g/bhphr) of NOx + non-methane hydrocarbons (NMHC), and 0.12 g/kW-hr (0.09 g/bhp-hr) of particulate matter (PM) and future standards. Typically, an HPDI engine is capable of reducing NOx emissions by 40% over diesel operation at the same efficiency. On a mining truck meeting Tier 2 standards, this NOx reduction would translate into NOx emissions approximately 14 t per year lower than under diesel operation. PM emissions are typically reduced by some 60% with HPDI fueling, which would translate into a yearly reduction of 650 kg. Similarly, engine-out greenhouse gas (GHG) emissions are reduced by 21%, resulting in a yearly reduction of approximately 950 t per vehicle.Above those of emissions reduction, efficient natural gas usage in mine haul operations would offer significant benefits in terms of fuel cost savings, which may be further combined with monetary emission credits. HPDI technology would enable operators to exercise environmental stewardship while gaining a competitive advantage in advance of new Tier 2 and Tier 3 emissions regulations. The advantages of natural gas use among mine haul truck operations can be replicated across a broad range of engines and applications."

Jan 1, 2005

Pressure for Better Safety Practices ? Increase Government Regulation ? Safety practices evolve from: ? Increased efficiency and performance ? More knowledgeable workforce ? Focus on decreasing risk to shareholder value In Order to achieve this ? Focus Points: ? Skill Development ? Best practices ? Situation-based decision making ? Enablers: ? Adoption of new technologies ? Transformed miner education ? Delivering on-demand information to the point of work Results: Miners empowered to improve mine safety

Aug 1, 2013

By Dayang Datu Khalil, Charle Amoah, Fred Kock

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By R. Siy, O. Neiman, B. Hilscher

"A full-scale prototype of “Jameson Downcomer” technology has been installed and tested on a Tailings Oil Recovery (TOR) vessel in Syncrude’s Mildred Lake extraction plant. Jameson Downcomers are a type of mineral flotation equipment used in the coal industry that Syncrude has extended to the recovery of secondary bitumen in the oil sand extraction process. The TOR vessels are currently being operated as single-gravity separation vessels, in series with the Primary Separation Vessels (PSV’s). We have developed a model to differentiate between “floating” and “non-floating” bitumen in the PSV’s, and then applied it to verify that the current TOR performance only captures the “floating” bitumen by simple separation. The existence of “non-floating” bitumen provides an opportunity for recovery enhancement by means of the Jameson Downcomers. To achieve bitumen recovery enhancement, middlings slurry is withdrawn from the TOR vessel, and passed through a number of parallel Jameson downcomers, within which the slurry is accelerated to a high-velocity free jet, and impinged upon the slurry surface inside the downcomer, in the presence of air. The aerated slurry is returned to the middlings zone inside the TOR, resulting in an incremental recovery improvement of bitumen in the TOR. The operation of the downcomers is thought to produce suitably small air bubbles for the flotation of bitumen, either by fluid shearing during the slurry jet impingement, and/or by micro-bubble nucleation. This full-scale prototype design has met or exceeded the recovery expectations of the original Research piloting, recovering at least 40% of the non-floating bitumen. In Syncrude Extraction, this provides high business value by a separation efficiency gain achieved with modest expenditure. As well, the system has demonstrated excellent operability and maintainability.INTRODUCTION Syncrude Overview Syncrude Canada Ltd. is one of the largest producers of crude oil from oil sands. Our crude oil production facility has the capacity to produce over 15% of Canada's total oil requirements. To do this, we surface mine oil sand, extract the raw oil known as bitumen from the sand using water-based processes, and upgrade that bitumen into sweet light crude oil by fluid coking, hydro processing, hydro treating and reblending. Our final product, Syncrude Crude Oil (SCO), is sent by pipeline to three Edmonton area refineries and to pipeline terminals which ship it to other refineries in Canada and the United States. The Syncrude operation is comprised of four major technology areas: Mining, Extraction, Upgrading and Utilities. As well, Syncrude invests more than $40 million annually in science and technology, and is among the top 50 companies in Canada for Research and Development (R&D) investment. Syncrude holds 21 active Canadian and U.S. patents."

Jan 1, 2012

By Peter Rubie, Toni Kojovic, Fengnian Shi

"Mining companies have recognized that characterization of ore breakage plays an essential role in the design and optimization of comminution circuits.Recently the Julius Kruttschnitt Mineral Research Centre (JKMRC) has developed a new breakage model incorporating the effect of particle size, and a new breakage characterization testing device, called the JK Rotary Breakage Tester (JKRBT), which allows rapid testing of particle breakage under high energy single impact and low energy repetitive impact conditions.Positive feedback received from mining company sponsors to the new technology has prompted the JKMRC to further validate the device and the model through a formalized validation program using machines designed and manufactured by Russell Mineral Equipment (RME). The first unit was installed and commissioned at the Anglo Platinum laboratory in Johannesburg in March 2007 and four more major mining companies will participate in the validation program in 2008, including Barrick, BHP Billiton, Rio Tinto and Teck Cominco. The results from validation tests at the JKMRC and Anglo Research have shown that the JKRBT generates statistically similar breakage parameters to the traditional Drop Weight Test, but with significant advantages over its predecessor. Application of the JKRBT in geometallurgical testing with the AMIRA P843 GeM project has confirmed the JKRBT device offers a rapid and consistent method for determining the hardness of drill core samples. The JKRBT has the potential to revolutionize ore testing, with applications in laboratory impact breakage characterization of rock samples, drill cores, coal and other materials. It also stands poised to significantly advance the process control and management of comminution circuits since the concept is readily adaptable to on-line ore hardness measurement.INTRODUCTIONMining companies have long recognized that the performance of a comminution machine such as a crusher or an autogenous / semi-autogenous grinding (AG/SAG) mill depends not only on the machine operating conditions, but also on the “hardness” of the feed material to be broken. This recognition has driven significant interest in laboratory particle breakage characterisation and testing. The laboratory breakage characterization tests can be roughly classified in two broad groups based on their primary breakage modes: tumbling and impact/compression. The famous Bond ball/rod mill tests (Bond, 1952 and 1961) represent the typical tumbling test and have become the industry standard for estimating the specific energy (kWh/t) of rod and ball mills. However, as the energy application in the single particle impact tests can be well defined and controlled, the latter have received significant attention in the last 30 years. It was estimated that mining companies worldwide spent over three million US dollars on single particle impact breakage characterization testing in 2006."

Jan 1, 2009

By Anand Raman, Steve Dixon

"Industry practice for defining acid consumption is based on column tests. Freeport-McMoRan (FCX) has adopted a practice of leach operation using a defined pH or gpl acid in the raffinate based on the column test program. The acid consumption can be easily calculated using the leach operating parameters of SX-EW efficiency, lift height, bulk density, irrigation rate, primary leach cycle time, acid cure dose and acid concentration in the raffinate. The column leach test results and a column to heap efficiency factor are used to define the copper extraction. The maximum acid consumption will occur when zero acid is contained in the raffinate. The term Net Extracted Value (NEV) is to define the maximum extracted value relative to acid consumed.This paper presents the operating logic and method used to calculate acid consumption based on column tests and operating parameters.INTRODUCTIONIndustry practice for defining acid consumption is based on column tests. This may result in lower economic value if the tests are not designed to account for operating variables. A test program is described to assist in defining lift height and the influence of gangue on solution chemistry. A simple spreadsheet is presented that will use the leach operating parameters of SXEW efficiency, lift height, bulk density, irrigation rate, primary leach cycle time, acid cure dose and acid concentration in the raffinate to calculate the acid consumption for a proposed operation.A review of current leach operations solution chemistry will help to define acid consumption. This is recommended for all current leach operations.DISCUSSIONThe current practice at Freeport-McMoRan (FCX) is the use of column test results to define operating parameters. The monitoring of operational solution chemistry and copper production addresses any changes needed in operational parameters. This practice maximizes the value extracted from each tonne of ore leached."

Jan 1, 2008

By Eric Konigsmann

"The Pogo project is located on the Goodpaster River, 38 miles north of Delta Junction in east central Alaska. Sumitomo Metal Mining and Teck Corporation are planning to develop a 2,500 ton per day underground mine and mill at Pogo. A preliminary resource of 5.5 million ounces of gold has been identified in two flat lying lenses. An underground adit has been developed to facilitate underground drilling of the deposit and to provide samples for bench and pilot scale metallurgical testwork.Flowsheet development included the evaluation of several processing options. The final flowsheet selected includes SAGhall mill grinding, gravity concentration with intensive cyanidation and direct electrowinning, sulfide flotation with ultrafine regrinding, and cyanide leaching and CIP gold recovery from the flotation concentrates. Flotation tailings will be filtered for placement in a dry stack storage facility or disposed of as paste backfill underground. All of the CIP tailings will be disposed of underground as paste backfill. A pilot plant was carried out to evaluate the proposed flowsheet described above and to confirm the gravity recovery predictions.Great care was taken in the development of the flowsheet and site layout concepts to mitigate the environmental impact of the proposed operation. An overview of the site water management concepts is presented and the impact of water issues on the process flowsheet is discussed."

Jan 1, 2002

By R. Webber, D. Averill, L. Whittle, D. Moffeti, G. Kassakhian

"This paper describes the recent pilot-plant work carried out on two alternative processes capable of producing an effluent containing less than 10 pCi/L total radium-226 activity and very close to 3 pCi/L dissolved radium-226. The processes incorporate coprecipitation of radium with barium sulphate by the addition of barium chloride in continuously stirred tank reactors followed by either chemical coagulation with ferric chloride, flocculation and clarification, or polymer-aided dual-media filtration. IntroductionUranium mines in Canada have practiced radium removal from tailings basin effluents since 1965. Treatment consists of addition of barium chloride to precipitate radium as barium- radium sulphate and provision of natural or constructed settling ponds for sedimentation. This process, however, has been identified as being deficient in that it allows particulate or suspended radium-226 releases which are higher than the regulated dissolved values». Also, the large size of some of the settling ponds is believed to represent a real limitation of the present technology because of inferred difficulty in recovery of barium-radium sulphate precipitates.The Federal Government Mining Task Force established a Radioactivity Sub-Group in 1974 to assist in the development of effluent regulations and guidelines for the uranium mining industry. Among the recommendations of the Sub-Group was the need to seek more effective methods of radium removal, including development of physical/chemical treatment systems as an alternative to settling ponds. In response to the SubGroup recommendations, a bench-scale study began in March 1976at the Wastewater Technology Centre (WTC) of Environment Canada . The results of this study indicated that coagulation and flocculation of the precipitate from barium chloride addition is a viable alternative to sedimentation in settling ponds(3). The bench work was expanded and accelerated in 1977, with financial assistance provided by the Atomic Energy Control Board. Subsequently, a research program with a larger scope was developed; this program is jointly managed and funded by government and industry, as shown in Table I.One of the goals of the joint program is to develop, at pilot scale, a physicalI chemical process to reduce the radium-226 content of uranium mining and milling effluents. Target radium-226 activities for treated tailings basin effluents were set: namely, 10 pCil L total and 3 pCil L dissolved radium 226. Extensive bench-scale and pilot-scale work was conducted through 1978 and 1979 and has culminated in the development of two physical/chemical processes. This paper describes work carried out at a pilot plant which led to the selection of the two physical I chemical processes for demonstration. In short-term tests, the processes produced effluents meeting the radium-226 target activities."

Jan 1, 1980

By P. Keating, J. Goutier, J. Ayer

"New, high-resolution geophysical surveys were undertaken over parts of the Abitibi Subprovince, Canada, to help with geological mapping and to promote mineral exploration. Gravity surveys in the Rouyn-Noranda and Matagami areas (Québec) allowed better 3-D mapping of important geological structures, and a multiscale edge analysis of ground gravity data over the Blake River Group confirms that major faults behave at depth as predicted by surface geology. Airborne gravimetry west of Matagami (Québec) helped to identify a new trend south of Lake Grasset that is almost perpendicular to the assumed geological trend of the area. Electromagnetic (EM) surveys, flown in the Chibougamau (Québec) and Bartlett Dome (Ontario) areas, allowed new conductors to be identified at greater depths than were achievable with previously used EM systems. Airborne magnetic surveys were flown in the Burntbush area (Ontario), and other available high-resolution magnetic data were compiled to produce a continuous and homogenous magnetic grid of the Abitibi region.The resulting compilation map clearly shows the locations of dikes, faults, and shears zones, and reveals some fault extensions in areas of extensive overburden. This grid also allows the computation of enhanced maps, such as vertical derivative and tilt maps (e.g., a tilt map shows subtle magnetic features in the Blake River Group that are difficult to see in the total magnetic field or its first derivative). Results from these new surveys show there is considerable value in (1) resurveying areas covered by older surveys, and (2) recompiling data sets from these older surveys."

Jan 1, 2012

By Patrick Polk

For many years, sulfuric acid producers all over the world have been forced to meet ever more strict environmental regulations to reduce SO2 emissions. The sulfuric acid industry has implemented new solutions in order to comply with the new lower SO2 emissions target. Haldor Topsoe (Topsoe) has responded to this challenge by continuously improving the range of VK sulfuric acid catalysts and providing tailor-made catalyst solutions to meet the demands of the sulfuric acid producers for lower SO2 emissions. Reducing emissions through catalysis: requires less capital than installing a scrubber, requires no additional process chemicals, generates no waste or by-product to dispose of. In 1996 Topsoe introduced VK69, a cesium-promoted vanadium catalyst, designed for operation in the pass(es) after the intermediate absorption tower in double absorption plants. The high activity of VK69 allows for a more than 50% reduction in SO2 emissions from existing double-absorption plants. Topsoe currently has more than 110 installations of VK69. To comply with the still more stringent regulations being placed on the sulfuric acid industry to lower SO2 emissions, Topsoe has developed a new sulfuric acid catalyst designated VK-701 LEAP5™. This catalyst was introduced to the market in 2010. VK-701 LEAP5™ is based on a novel technology which circumvents the internal transport deficiencies of existing commercial sulfuric acid catalysts and thereby offers exceptionally high activity in strong, SO3 rich gases. Sulfuric acid plants have used this catalyst to meet emissions requirements lower than previously believed possible with a catalyst only solution. This paper will present examples on how to reduce emissions by implementing a tailor-made catalyst solution using VK69 and VK-701 LEAP5™.

Jan 1, 2014

By Phil Thwaites

"The mining industry uses many types of mineral and metallurgical plants to produce saleable product from ore mined. Plant design history has left current operations with a mixture of manual operation and various forms of automated process controls. Consequently, we typically see high variability in the continuous operations together with a shortfall in the attainment of full capacity, or higher utilization of consumables.At a level of best practice, “Operational Performance Excellence” focuses on process control, using automation and control systems to deliver process optimization. This more sophisticated delivery is a great deal more difficult than the first stage of equipment selection / installation. It includes the appropriate selection of the right instrumentation, control system, key process knowledge, individuals with a solid control engineering background/experience, and the essential backing/ support of the operations management team together leading to higher value delivery. Robust solutions can be realized, considerably minimizing process variation, thus leading to process optimization. This approach results in an easier, efficient and safer process while providing considerable returns for the plant owners.How variable are your processes, and do you maintain optimized process performance with dedicated resources, modern instrumentation, ‘best practice’ control systems and performance monitoring tools? In this lecture, these questions and their possible answers are discussed.357"

Jan 1, 2013

The negative effects of pyrite and pyrrhotite on thiosulfate gold leaching have been investigated. Possible remedies to reduce some problems are discussed. In a gold bearing pure silicate ore, 92% of gold could be extracted within 3 hours using a solution containing 0.2 mol/L ammonium thiosulfate, 0.9 mol/L ammonia, 30 - 300 ppm copper sulfate and 8.6 ppm dissolved oxygen at pH 10.26. The thiosulfate consumption was 7.1 kg/t under these conditions and could be further reduced to 3.5 kg/t by decreasing the dissolved oxygen to 0.3 ppm. Addition of 16% pyrrhotite or pyrite into the silicate slurry led to a decrease in gold extraction by 2% or 9% respectively and an increase of thiosulfate consumption by 11 kg/t or12.8 kg/t respectively in three hours. Several adjustments, such as increasing copper ion and ammonia concentration and reducing the dissolved oxygen level to 0.3 ppm resulted in increased gold extraction and lower thiosulfate consumption despite the presence of these sulfides.

Jan 1, 2005

By Patrick M. Y. Waye

As mines utilise more automation in mining operations to improve efficiency and safety, a corresponding increasing demand is placed on the transport of information. Some of the recent technological advances in underground telecommunications are described for various data, voice and video applications. In particular, two new innovative underground communication systems are described, one with high speed data at 30 Mbps and the other for mine wide evacuation and safety applications. The high speed data system incorporates stateof- the-art data networking technologies and the existing leaky cable narrow band radio channels. The new system provides over the same basic infrastructure the high speed data network at 30 Mbps TCP/IP Ethernet with 100 Base-T interconnection, plus 32 narrow band radio channels. The second system is a system for mine wide evacuation with "through the earth" communication infrastructure. Emergency situation can be communicated to and from all the miners within seconds through a central control location. The technology involved does not require leaky cable or any other similar transmission media installation. Many applications are possible, including warning miners of emergency situations, mine rescue operation to communicate with trapped miners, regular reporting from miners working alone.

May 1, 2001

By K. J. Fair, H. W. Smith, D. R. Francis, J. M. Toguri

"Bench-scale batch milling and screening tests were carried out on secondary aluminum dross 10 produce an aluminum concentrate. To complement these tests, an analysis of a commercial plant was also performed by sampling dross at various stages in the plant's milling and screening circuit. These studies have indicated that benefits of increased capacity, grade and recovery of aluminum metal can be realized by addition of screens before the ball mill, longer grinding period and by grinding the smaller size fractions more efficiently.To test the predictions, a plant test was performed on the milling of100tons of secondary dross. The recycling of the large size fraction (+1/8 in.) of aluminum dross through the impact mill rather than through the rate limiting ball mill resulted in a comparable aluminum grade. The ball milling of the _1/ 8 in. + 10 mesh size gave a dross grade of71% AI. A lower feed rate to the ball mill resulted in a higher final grade. With minor modifications, secondary dross can be processed in 22% of the time it takes with the present circuit without a sacrifice in grade.IntroductionSecondary aluminum dross is a mixture of metallic aluminum, aluminum oxides and salts (alkali halides). Any comminution process deforms or slowly grind s the malleable metal phase and reduces the size of the friable, brittle, oxide-salt phase relatively fasterr(1).The milling of aluminum dross is performed to upgrade the metallic aluminum fraction. Figure I shows a flowsheet for the milling of secondary dross as presently practised at Metals and Alloys Co. Ltd., Toronto, Ontario. At point A, large acceptable grade material is hand picked for refurnacing, the unacceptable off-grade material is sent to the sweat furnace and the remaining, + 2 in. fraction is recycled through the 3.9 ft by 4.1 ft impact mill. For simplification, three ball mills are shown. However, in reality there is only one, a 5 ft by 10 ft ball mill used in a semi-batch mode. The 2 in. + 3/8in. and 3/8 in. + 10 mesh products are remilled in the ball mill. The -10 mesh material is discarded as waste."

Jan 1, 1987