Search Documents

The influence of joint orientation and joint persistence, on the mechanical behaviour of jointed rock masses under uniaxial compression, has been studied systematically. The joint inclination angle ß was varied from 0° to 90° with an increment of 15°. The joint continuity factor k was taken as 0.2, 0.4, 0.6 and 0.8. The peak strength, Young’s modulus, the complete axial stress-axial strain curves, the cracking process and the characteristic of the fragments, were investigated. It was found that the anisotropic response of the jointed specimens was governed by the micro-mechanism, such as crack initiation, propagation and coalescence, crack opening or closing, and frictional slip of cracks or joints. With the increase of joint continuity factor, the axial stress-axial strain curves change from single-peak to multipeak, the peak strength and Young’s modulus decrease. The specimens with medium joint inclination angle (30°,45° and 60°) has lower energy dissipation and strength due to stepped or shear failure, while specimens with small and large joint inclination angle (0°, 15°, 75° and 90°) has higher energy dissipation and strength due to axial cleavage or crushing failure.

Jan 1, 2015

By J. L. Nebreda, Z. Fan, J. B. Patel

"A380 alloy has been widely employed to produce thin-wall components via high pressure die casting (HPDC). During HPDC processing, there is a significant problem of property variation even with the very stable and precision automated casting procedure. The enlarged variation lowers the component performance and affects the steady and uniform property distribution along the whole component. In this study, high shear melt conditioning technology was developed and applied to the melt prior to pouring into the shot sleeve. Experimental results show that with application of intensive melt shearing, the variation of elongation was decreased from 21.8to 13.9%, and yield strength variation was reduced from5.5to 3.6%. The improved property variation is attributed to enhanced nucleation both in shot sleeve and the die-cavity, and to the improved distribution of porosity and secondary phases as a benefit of high shear induced grain refinement. With application of high shear, large number of the Spinel phase (MgAl2O4) particles with double size distribution in average diameter of 80and 300nm were formed. Due to the good orientation relationship and small misfit between alpha Al and MgAl2O4, the particles act as the effective nuclei in shot sleeve and die cavity, respectively.INTRODUCTIONA380 alloy had been widely used for produce automotive components by cold chamber high pressure die casting(HPDC) processing, due to its relative good mechanical properties and cast ability performance, and more important most of A380 ingots were produced by recycled Al alloys. Therefore, to promote utility of A380 will contribute to reducing emission of CO2and to the lightweight of automotive industry as well. When cold chamber HPDC was employed to produce the components, the mechanical properties of A380 alloy always have a distribution range (named variation herein), or in other words the properties were not stable. The reason was ascribed to the typical solidification characteristics occurred in HPDC processing. During HPDC processing, there are three steps of melt movement. The first step is that the melt was poured into shot sleeve at temperature of about 680°C, in which shot sleeve was preheated by few shots of melt filling, or by heater. During step one, the first solidification of melt was happened in shot sleeve and about 20% solid made of coarse a-Al grains was formed(Li, Xiong, & Guo, 2016).Such kind of grains will retain in the final products and deteriorate the properties variation. The second step is that the melt was forced moving forward slowly by plunger at about 0.2–0.3m/s until the liquid melt front to the inner gate of mold. The third step is that the melt moved very fast to complete the filling of die cavity and refilling the solidification shrinkage by fast movement of plunger about 2–3m/s. The second solidification was occurred in die cavity and fine a-Al grains will be formed by high cooling rate at about 500–1000°C/s. From the solidification point of view, the grain size was dominated by nucleation and growth. When HPDC was employed to produce components, the melt quality becomes the priority factor to control the solidification process as the other casting parameters were kept at the same."

Jan 1, 2018

By Jakob Janzen

This paper demonstrates that the introduction of a Battery Energy Storage System (BESS) into an isolated diesel generator based grid has the potential to reduce the electricity cost and deliver a good return on investment. Energy storage also allows for increased renewable energy penetration, into the isolated grid, that further reduces the electricity cost. The isolated power system studied includes several diesel generators of different sizes. The typical operating pattern is for the generators to be run at 80% to 85% of their power rating to deal with load fluctuations. Operating the diesel generators near their full power rating, however, improves their efficiency, in this case, while the frequency and load control can be carried out by the BESS. Operating the diesel generators near their full power rating reduces the number of generators which need to be operating to support a given load. As a result, the improved efficiency of the diesel generators and reduced maintenance cost, for operating fewer machines, are the reason for the savings.

Aug 1, 2013

By O. Moselhi

Material can be seen as the fuel needed to execute the project from inception to completion. Material installed provides good indicators of progress achieved onsite vis-a-vis project schedule performance. It correlates well with the role of the schedule performance index (SPI) of the earned value method (EVM). Material is recognized to have a significant impact on achieved progress for physical completion of project activities. This paper presents a study on the development of material status index (MSI) in support of the EVM. Unlike the SPI, the newly developed index account for the criticality of project activities. This is carried out considering the total float of each activity, percent float (i.e. the ratio of float to activity duration) and the total float of the path on which the activity is located. MSI, can independently and jointly with SPI provide root causes behind problems encountered during project execution. In turn MSI can reveal material related factors behind the performance detected by joint interpretation of the two indices. MSI serves to provide added value in alerting management to take corrective actions. While SPI and MSI may have different values, they can jointly augment and enrich the captured project status based on EVM. To demonstrate the capabilities of the developed MSI method, it is implemented on a case study. The case encompasses the construction schedule of a hydro power station constructed in northern Quebec. Different scenarios are adapted from the real case to demonstrate a set of practical aspects of the developed index. The results generated from the analysis of the case study illustrate the useful features of MSI beyond those of the traditional SPI on two fronts; causation and the considerations of criticalities of actives.

Aug 1, 2013

By S. Minamiguchi

Grain refinement is effective to enhance strength and ductility of metallic materials. However this advantage has not been utilized fully for magnesium alloys in industry because microstructure control through thermomechanical treatment is difficult owing to their poor deformability. The authors proposed a high-speed heavy-reduction rolling for production of Mg alloy sheets. It was found that the deformability is significantly improved at high speed and that the thickness can be reduced 60% by one-pass operation even at room temperature without fracture at the rolling speed higher than 1000 m/min. In this study, commercial AZ31B sheets were rolled at 2000 m/min between room temperature and 350°C, and quenched immediately after the rolling. The sheets rolled at 200°C show the finest recrystallized microstructure with the mean grain size of 2.2 Rm. They show outstanding mechanical properties with the tensile strength of 293 MPa, and the elongation of 25%. It is concluded that high-speed rolling is very advantageous for grain refinement and improvement in mechanical properties as well as deformability and productivity.

Jan 1, 2006

By F. Czerwinski

Mechanically fragmented chips of an AZ91D magnesium alloy were transformed into a semisolid slurry within the Thixomolding® system. Microstructural analysis of a material at various processing stages revealed that the cold deformation of the alloy, experienced during chipping, led to the recrystallization and growth of equiaxed grains which were subsequently converted to the globular structures by melting the grain-boundary network.

Jan 1, 2004

_What is standard technology infrastructure _ Business Context _ The mine operator?s technology challenges and needs _ The benefits of technology standards _ Overview of the SMART initiative _ Technology standards description _ Current status _ Next steps What is Standard Technology Infrastructure Technology Infrastructure is: ? Networking communications ? Computing operating systems ? Hardware platforms ? Data storage and access ? Operator interface _ These components are based on recognized open standards organization, and _ Commonly and widely utilized by industry, and _ Commercially available off-the-shelf systems (COTS), both hardware and software _ Standard capability to provide immediate and open access to raw or derived data at source, APIs, configuration parameters & sub-routines from all system components; ALL CURRENTLY AVAILABLE

May 1, 2008

By J .. A. Nemes, I. Ragai

This paper discusses one of the common problems associated with sheet metal forming processes, which is spring back. The materials presented here, stainless steel 410 and Inconel 718, are commonly used in aerospace applications for their superior material properties. Standard tensile tests were performed to determine their tensile properties, as well as material anisotropy. In addition, the effect of anisotropy on springback was assessed experimentally through simple multiple-bending experiments in different directions to the rolling direction. Finally, draw-bending experiments were carried out to study the effect of forming conditions, such as blank holding force, on the final springback angles of the formed parts. For both materials, it was found that the R-values measured for different sheets exhibited variation. However, the specimen orientation does not have a large effect on material tensile behavior or springback angle for simple bending. For the Inconel 718 specimens, the springback angle slightly increases with each stage of deformation during multiple bend experiments. The effect of the blank holding force on springback angles was also examined and found to have a significant effect on thin specimens.

Jan 1, 2006

By D. Royston

In SAG mills fed with a variety of ore types, hard packing between the shell lifters can come and go depending on rock type and rock size distribution and the presence of a binder. Packing can appear in all sizes of SAG mills, and can be tenacious. High ball impact forces (depending on ball size) in larger mills may compact and encourage packing. Packing can have a negative impact on milling performance and a change in shell liner design may be required to remove it. However shell liner design changes need to be managed with care to ensure liner reliability. In smaller mills control of packing can extend shell plate wear-life and may help to maintain milling performance in fixed-speed mills through the liner wear-cycle.

Jan 1, 2012

By K. Chomyn, R. Veenstra, P. Zangeneh, Hatch Ltd., C. Van der Woude, H. Ghorbani

"The furnace is the heart of smelting operations, and therefore the performance, reliability, and campaign life of the furnace are critical considerations. Furnace refractory is exposed to high temperatures and other harsh operating conditions causing brick erosion, crushing, and cracking, typically limiting the furnace campaign life and requiring costly furnace shut-downs for refractory re-lining. Despite extensive study, the in-service thermal / mechanical stresses in these complex refractory systems are not generally well understood. Hatch has developed a thermal-mechanical finite element analysis (FEA) based furnace refractory modeling approach that allows for the quantification of refractory movements, load distribution, and thermal / mechanical stresses.Due to the complexity of the refractory system, a range of models are used to identify and assess damage mechanisms and design improvements, including: 2D models, to capture expansion and movement of individual bricks, changes to load paths, and thermal stresses; and 3D models, to include the effect of differential expansion between bricks in each course, and assess overall load distributions. The 2D and 3D analyses include the effect of nonlinear temperature-dependent properties, thermal expansion, movement of individual bricks with frictional contacts (i.e., gaps can open, bricks can slide), and brick tensile or compressive failure. Both as-built and damaged conditions can be investigated (e.g., after bath zone brick erosion), for circular and rectangular furnaces. 3D models also include papering and brick joint & interface action.Analyses using these models have shown the importance of thermal stresses, papering, and geometry / arrangement of individual bricks. Results have been used to identify and assess damage mechanisms, showing good alignment with furnace autopsy observations. By using this FEA-based approach to quantify the refractory design, the risk of damage can be significantly reduced, low-cost design changes can be identified, and the furnace campaign life can be extended.INTRODUCTIONThe furnace is the heart of smelting operations and therefore the performance, reliability, and campaign life of the furnace are critical to the success of the smelting operation. Furnaces are inherently exposed to high temperatures, often in excess of 1600°C (Holappa, 2004), and furnace operating power has progressively increased over time (Voermann, Gerritsen, Candy, Stober, & Matyas, 2004). The refractory system must withstand high temperature, high heat flux, and other harsh operating conditions. These conditions are particularly significant for the furnace hearth, and can lead to damage including brick erosion due to molten material flows, crushing due to thermal expansion loads, and cracking due to severe thermal gradients within the bricks. Refractory damage typically limits the furnace campaign life, requiring costly furnace shut-downs for refractory re-lining (repair or replacement). In some cases the refractory may lose integrity causing damage to nearby equipment and harm to personnel."

Jan 1, 2016

By Andrew Bamber

Outline ?Background to Mine-Mill Research at UBC ?Mine Mill Integration ?In situ mining methods ?Underground Pre-concentration ?System Design and Supporting Technologies ?Case Studies: ?INCO -McCreedyEast Mine ?Placer Dome ?Porcupine JV ISL Study ?Musselwhite, South Deep ?Falconbridge ?Fraser Copper ?Thayer Lindsley ?Wayside Gold, other scoping studies? ?System Designs ?Summary ?Future work ?Conclusion

May 1, 2006

By William C. Boggis

EKATI? Diamond mine is located 300km northwest of Yellowknife and 200 km south of the Arctic Circle in the Northwest Territories of Canada. The site is a remote tundra area with continuous permafrost and is in the Canadian Shield. EKATI? is the first diamond mine in Canada and is operated by BHP Diamonds Inc., which is a part of BHP Minerals. BHP Diamonds Inc. is an incorporated company based in Vancouver, BC. The mine is a joint venture of BHP Diamonds Inc. (51%), Dia Met Minerals Ltd. (29%), Charles E. Fipke (10%) and Dr. Stewart L. Blusson (10%). The mining area lies within the 10,960 ha land leases held by the joint venture. The total claim block covers 344,000 ha. To date over 136 kimberlite structures have been identified within the claim. Five of these provide the basis for the present mine plan with three others identified for future inclusion. At full capacity the mine will produce 4.5 million carats per year, approximately 4 % of world production and employ approximately 600 people, with over 33% being Aboriginal from the Northwest Territories.

May 1, 2001

By Rodney S. Read

Both crystalline and sedimentary rocks are being considered to host a deep geological repository (DGR) for nuclear fuel waste in Canada. In the past several decades, considerable research has been conducted around the world to better understand geomechanical processes associated with development and long-term performance of a DGR. The Nuclear Waste Management Organization?s (NWMO?s) technical research and development program is examining a number of potentially suitable rock formations to support implementation of Adaptive Phased Management, Canada?s approach for long-term management of nuclear fuel waste. Rock engineering will play an important role in siting, design, and construction of a DGR for nuclear fuel waste. Post-construction activities such as excavation maintenance, monitoring, decommissioning, and closure will also involve rock engineering. The type of host rock selected for a DGR will influence the scope of rock engineering activities and related research requirements. This paper outlines key rock engineering aspects to be considered in developing a DGR in sedimentary rock.

May 1, 2009

By Z. Zhang, X. -G. Chen, F. Breton, A. Arici

"The microstructure of Al-10Si-0.3Mg-0.5Mn alloy with 0.27% Zr and 0.19% V addition was quantitatively analysed and compared to the base material. The addition of Zr and V in the AlSi10Mg alloy exhibit a beneficial effect on the Si modification, resulting in the reduction of the size of eutectic Si particles on both as-cast and T6 conditions. The quantitative image analysis results show that the Zr and V addition and T6 treatment can reduce the size of the intermetallic phases. In addition, the presence of Zr and V is favour to the partial dissolution of the intermetallic phases during the T6 treatment. Different heat treatment procedures were tested to optimize treatment parameters. The mechanical properties of the alloys were evaluated using hardness measurements and tensile tests. The results show that the addition of Zr and V can remarkably improve the mechanical properties on as-cast and T6-treated conditions. The correlation between the microstructure and mechanical properties of the alloys is discussed.INTRODUCTION Al-Si-Mg foundry alloys have been widely used in automotive and aerospace industries due to their high strength-to-weight ratio, heat-treatable capability and excellent castability. The alloying elements such as Cu, Mn, Fe are traditionally added into Al-Si-Mg alloys to improve their mechanical properties (Mohamed, Samuel, Samuel & Doty, 2009). In recent years, the attention has been paid to the effect of the transition elements such as Zr, V, Ti, etc, as minor alloying additives, on the properties of aluminum alloys (Elhadari, Patel, Chen, & Kasprzak, 2011; Kasprzak, Amirkhiz & Niewczas, 2014; Shaha, Czerwinski, Kasprzak, Friedman & Chen, 2015; Shaha, Czerwinski, Kasprzak & Chen, 2014; Mahmudi, Sepehrband, Ghasemi & 2006; Meng, Cui, Zhao & Zuo, 2013). Kasprzak et al., (2014) and Shaha et al., (2015) reported that additions of Zr, V, and Ti in Al-Si-Cu-Mg cast alloys can improve the alloy mechanical properties at high temperature by forming stable intermetallics and precipitates on as-cast and heat treatment conditions. On the other hand, the mechanical properties of near-eutectic and eutectic Al–Si cast alloys depend not only on the chemical composition but also, even more importantly, on microstructural features such as the morphology and size of eutectic silicon and intermetallic particles, which are present on both as-cast and heat treatment conditions (Mohamed et al., 2009). However, there is rather limited information on the effect of Zr and V on the microstructure features and mechanical properties of near-eutectic Al-Si-Mg cast alloys."

Jan 1, 2018

By J. H. Pateson, D. C. Comrie, D. J. Ritcey

"Geopolymers are inorganic semi-amorphous three dimensional silico-aluminates of the poly(sialate) type (-Si-O-Al-0-) or of the poly(sialate-siloxo) type (-Si-O-Al-O-Si-0-). Polycondensation occurs at low temperatures with geopolymers being stable up to 12oo0 c. Research, development and application technology pertaining to geopolymers is being undertaken jointly with Dr. Joseph Davidovits of The Institute for Applied Archaeological Sciences of Florida, U.S.A. This joint focused upon the chemical Barry University in Miami Shores, research and development program has stabilization and solidification of various waste products through geopolymerization. Of particular interest is the geopolymerization of mine wastes including tailings and waste rock derived from the processing of base metals, precious metals, potash, coal and uranium deposits.INTRODUCTIOND. Comrie Consulting Ltd., in cooperation and technical liaison with CANMET, Ottawa has been testing the application of geopolymers to mining wastes. Corporate efforts to date have concentrated upon reactive acid tailings, principally from the abandoned Kam-Kotia Mine site, and dewatered paint waste sludges. Test work conducted to date has successfully yielded geopolymer treated materials and wastes with increased chemical and structural stability. Wastes containing heavy metals, cyanides, arsenic and sulphur dioxide have been successfully geopolymerized."

Jan 1, 1988

By O. Kodym

The paper has focused on possibilities of interconnecting information sources concerning monitoring & control of mining industry technical processes (TP), and the related safety hazards. The key issue is the comprehensiveness of the information presented to users. Information can be presented by virtual reality means, when the seemingly true presentation of the production process scene along with user friendly presentation of related information is available. The user in its role of a process supervisor is not only a mere scene observer but, thanks to the interactive functions of virtual environment, he participates in the scene of his control. As such his control and management abilities increase because he can absorb, more easily understand and asses the information provided.

Aug 1, 2013

By W. Melnyk, L Pokhilenko, J. A. McDonald, A. Hall

The Camsell Lake property comprises 270 000 acres located about 240 kilometres northeast of Yellowknife in the Northwest Territories. Kimberlite has been located in two areas of the property:

Jan 1, 2001

By K. B. Han, S. Winkler, M. J. Benoit, M. J. Worswick

"Automotive heat exchangers are fabricated by forming multi-layered aluminum (Al) alloy brazing sheets into the desired geometry and subsequently passing the assembly through a furnace for brazing. As manufacturers seek to use thinner gauge and higher strength sheet to reduce vehicle weight, forming of the Al alloy sheets has become a challenge. Warm forming has previously proven to allay these forming concerns, but no consideration was given to the effect of increasing the forming temperature on brazing. Recently, it was shown that annealed sheet was more susceptible to the detrimental phenomenon of liquid film migration (LFM) during brazing if formed above 150°C, while work hardened sheets showed no increased susceptibility to LFM with increasing forming temperature, up to 250°C. In the current study, the brazing performance of simulated battery cooling plates was investigated. The plates were fabricated both from fully annealed and work hardened sheets. Brazing was assessed by microstructural evolution during a brazing cycle. The post-brazed microstructure varied with strain and forming temperature in plates made from annealed sheets, while no variation in microstructure with location or forming temperature was observed in plates formed from work hardened sheets.INTRODUCTION Since the 1970’s, one common method of fabricating automotive heat exchangers has been by forming multi-layered aluminum (Al) alloy sheets, and subsequently brazing the formed components together in a controlled atmosphere furnace. The Al alloy sheets used are comprised of at least two Al alloys roll bonded together, but can consist of additional layers, depending on the application; at minimum, the sheets are comprised of a core and clad layer. The core layer, often an AA3xxx alloy, remains solid throughout processing and provides strength to the assembly. The clad layer is always one of the AA4xxx series alloys which, due to their high silicon (Si) content, have a melting temperature range well below that of the core alloy. When the sheet is passed through the brazing furnace, the clad alloy melts to provide the brazed joint filler metal throughout the assembly, while the core alloy remains solid. In order to achieve cost and weight savings, heat exchanger fabricators have used Al alloy sheets with reduced thickness. However, deformation and brazing of these increasingly thin components remains a concern (Zhao & Woods, 2013). Furthermore, springback has been observed after forming sheets of higher initial strength (i.e. work hardened conditions), leading to flatness issues of formed components. Consequently, the ability to form high quality brazed joints is difficult in components formed from higher strength brazing sheets."

Jan 1, 2018

By Jianzhong Liu

Based on the characteristics of overburden rock strata movement, surface ground subsidence and casing deformation and failure, a tension-shear combination failure model of surface borehole was set up. The main controlling factors of the mining-induced deformation and failure of surface borehole were researched with this failure model and the limit analysis method. The mining methods and geology conditions mechanics action mechanism to surface borehole and its time ?space evaluation rule was found. The surface borehole deformation and fracture rule were advanced. It provides theoretical support to optimizing layout, structure type, security measure and local casing protection of surface borehole.

Aug 1, 2013

By Cheng-Ting Chiang

Information integration and exchange for the entire building life cycle is one of the most important issues in the AEC industry. Although the Building Information Model (BIM) technology is widely utilized to address them, BIM is mainly concerned within the design and construction (D&C) phases. In the operation and maintenance (O&M) phases, however, the information integration and exchange issue becomes more complicated because software applications here require not only BIM but other information outside of the AEC domain, e.g., disaster mitigation. Nowadays, most BIM-related research focuses on the D&C phases and pays less concern on the O&M phases, hence there is a research need that can help seamlessly transfer the information between the D&C and O&M phases. In this research, a software framework using ontology was designed to deal with aforementioned problems. The BIM data from the D&C phases were used as a foundation to generate new models for different software applications for the O&M phases. The ontology technique was employed to assist the model transformation process between the original BIM and the models for applications. Finally, a disaster mitigation example was chosen to validate the framework, in order to make sure that the transformation process is comprehensive and useful from domain experts? perspective.

Aug 1, 2013