Search Documents

By Ian Orford, Peter Radziszewski, Lud Strah

"An autogenous grinding circuit was commissioned at the Brunswick concentrator in October 1998. The AG mill was subsequently converted to SAG operation in May 1999 for a number of reasons. The mill had 48 rows of the NORCAST top-hat integral lifter/liners configured in Hi-Lo mode. A charge motion simulation study, the results of which are the subject of this presentation, was initiated to develop a better understanding of SAG mill behaviour. Using a design of experiments approach, a lifter face angle was determined that would increase mill power draw. Once determined, lifter profiles were modified and installed in July 2001, and a second set installed in February 2002. Resulting changes in mill power consumption are presented.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is a large lead/zinc mine and began milling ore in 1964. The ore is massive sulphide with approximately 20% valuable minerals, 60% pyrite and 20% silicates. In October 1998, an autogenous grinding circuit was commissioned at the Brunswick concentrator (Cooper, Orford, Larsen, 2001).At the time, the autogenous grinding circuit replaced existing surface crushing plants, fine ore storage, rod mills and primary ball mills. The 8.54 m diameter x 4.27 m long (EGL) ANI mill was subsequently converted to SAG operation in May 1999.The mill had 48 rows of the NORCAST top-hat integral lifter/liners and was operated initially with all shell lifters at the same height. Following problems with packing and abnormal wear pattern, the profile was changed to a high-low configuration.Further, it was found that over the life of the lifters, mill power draw and throughput varied considerably. Although a change in mill power draw was expected following lifter replacement (predicted during mill design to be in the order of 300-400 kW), the replacement of the worn lifters with new high lifters resulted in mill power draw decreased by some 1000 kW."

Jan 1, 2003

By G. M. Ritcey, K. E. Haque, S. H. Lucas

"Laboratory-scale hydrochloric acid leach tests were conducted on an Elliot Lake uranium ore. Hydrochloric acid leaches without an oxidant or with molecular oxygen (i.e., air or pure oxygen gas) as an oxidant favoured uranium and radium extractions. Conditions for maximum uranium, thorium and radium extractions with hydrochloric acid in the presence of sodium chlorate were determined. The highest extractions of uranium (96%), thorium (81%) and radium (91%) were obtained using a mixture of 44.0 kg HCI and 2.5 kg NaCIOJ per tonne of ore at 75°C with 18 hours ' retention.Flowsheets for two-stage leaching are proposed. The residues obtained from the second-stage leach contain uranium (0.002%), thorium (0.006%) and radium (15 to 20 pCi/g). Tailings of this nature are considered suitable for mine backfill, and, if pyrite is removed, suitable for surfacedisposal.IntroductionThe nuclear energy industry forecasts an increasing demand for uranium. This increasing demand requires not only largescale mining and processing of conventional and complex uranium ores, but also leads to the consideration of new and nonconventional sources of uranium, e.g., black shales, phosphate rocks, granite, sea water and fossil-fuel ash.Sulphuric acid leaching is the most widely used process to extract uranium from the ore(l). The leach liquor is separated from the solids (tailings), purified, concentrated in various intermediate stages, and finally a semi-purified product, yellow cake (80-85070 U30 8) , is precipitated. The tailings, which constitute nearly 98% of the total bulk of most ores, are usually discarded in surface disposal areas.The Elliot Lake region of Ontario is one of the major uranium producing areas in Canada. The principal uranium minerals are brannerite and uraninite, present as microscopic grains in the matrix of quartz-pebble conglomerates. The average grade is between 0.10 and 0.15% UPs. Up to 6.5% pyrite is also present in the conglomerates. Because pyrite is less reactive toward sulphuric acid leaching, almost all the pyrite goes into the tailings and eventually into' the disposal sites."

Jan 1, 1980

By J. R. Goode

Rare earth elements (REE) and their compounds are critical ingredients in numerous necessities of modern life including: the permanent magnets used in electric motors, generators, speaker and hard drives; high performance automobile tires; catalysts; phosphors; optical glass; etc. World production of REE in 2014 was about 110,000 t with about 98,000 t/a being “Light” (LREE) and the balance “Heavy” (HREE). Unlike other mined commodities, the majority of the LREE produced in the world is a by-product and that from a single iron ore mine in China. The balance of the LREE production comes from four REE-only mines, two in China, one in Australia and one in the USA (now on Care and Maintenance basis). The LREE operations comprise very unusual flotation processes and complex hydrometallurgical plants. In contrast, most of the HREE come from a multitude of small in-situ leach operations exploiting a single, dispersed deposit in China using hydrometallurgy alone. All of the current REE operations produce an intermediate mixed REE product that must be separated to yield the high purity, individual, REE required by the market. This paper describes the processes being used to produce LREE and HREE intermediate products and the separation plants used to make the high purity REE compounds that are key ingredients in the magnets in earbuds, turbines, and automobiles; catalysts used in the production of gasoline, and so on.

Jan 1, 2016

By Frank van der Meer, Jorge Portocarrero, Alexandra Gruendken

"The number of High Pressure Grinding Rolls (“HPGRs”, also called Roller Press) installations instead of tertiary crushers is rapidly increasing. The technology has been largely accepted in the minerals industry and benefits, such as superior energy efficiency and a lower overall operating cost compared to alternative technologies, have been demonstrated at a number of operations throughout the world.This paper focuses on coarse hard ore operations and reviews the successful installation of the first Roller Press installed instead of a tertiary crusher at the Los Colorados Plant of CMH (Chile) in 1998. It details the experience obtained over the past ten years of operation from commissioning to the present day. It highlights examples of further developments made in the design to improve machine maintainability and availability as well as wear life of the grinding surfaces.A second focus lies on procedures to derive from small scale testing material properties such as wear life, flake formation and strength and their application to industrial size machines to optimize circuit design, especially when Roller Presses are used in closed circuit with screening.INTRODUCTIONRoller Presses (also known as HPGR, High Pressure Grinding Rolls) are considered today state of the art for the preparation of pellet feed. They are also gaining wide acceptance in coarse ore operations. One of the first successful operations in which a roller press was used to replace a conventional tertiary and quaternary crusher is the Los Colorados plant of CMH in Chile.When the Roller Press at Los Colorados was commissioned in 1988, there were 169 Humboldt Wedag roller presses in operation throughout the world. Of these, 14 were installed in the minerals industry. However, these were installed mainly for grinding pellet feed to increase the Blaine value. Up to that time, only three KHD roller presses had been applied for crushing coarse ore in specialized circuits. Moreover, the installation at Los Colorados was the first Roller Press ever to replace a conventional tertiary and quaternary crusher in a hard ore application."

Jan 1, 2009

By Dave Price

"Canada is scheduled to become the 4th highest diamond revenue producing country in the world by year 2004 with the already operating Ekati Mine and the anticipated operation of the Jericho Mine in 2002 and the Diavik Mine in 2003.This paper provides an overview of worldwide diamond production statistics and a brief introduction to a diamond processing plant. The dense medium separation (DMS) extraction process is presented and this process is discussed in more detail with respect to the extraction of diamonds in terms of feed preparation, dense medium, dense medium cyclones, ferrosilicon recovery and dense medium cyclone operating efficiencies.INTRODUCTIONThe Ekati Diamond Mine in the Northwest Territories started commercial production of diamonds in the 4* quarter of 1998. At full production, the mine is anticipated to produce annually some 3 million carats of diamonds. The Jericho Mine in Nunavut Territory and the Diavik Mine in the Northwest Territories are anticipated to come into production in the 1'' quarter of 2002 and 1st half of 2003 respectively. The combined annual diamond production of these three mines will total approximately 10.34 million carats by 2004, making Canada the 4~ highest diamond revenue producing country in the world.A diamond processing plant initially utilizes crushing, scrubbing and screening in the beneficiation process to liberate diamonds from kimberlite ore and size the product for further treatment through DMS. Alluvial diamond operations do not require initial crushing and scrubbing but incorporate a feed preparation and sometimes a recrush facility with the DMS plant. The heavy sink product from the DMS, which contains diamonds, is further upgraded through x-ray separation and high intensity magnetic separation prior to producing the final diamond product.DMS is a relatively simple separating principle. A mixture of particles of different density is immersed in a dense fluid, so that particles having a density lower than that of the fluid will float while those of heavier density will sink. The translation of the float-sink principle from a laboratory method to continuous industrial practice offers the prospect of very precise mineral separations based on density differences alone."

Jan 1, 2000

By S. Yalcin, S. Chang, M. Oliazadeh

"Present day ferrochrome demand is on the rise, as more steel products require this material as an alloying element. It is projected that the stainless steel demands will grow by about 6% per year to 2020; as such, the supply and demand for ferrochrome appears promising. Chromite is the only economical source of chromium, which is commonly upgraded by gravity techniques and used to produce ferrochrome. The gravity separation methods are not able to treat particles finer than 0.1 mm efficiently. Therefore, in processing chromite ore, a large quantity of fine tailings; some 25% of the mineral values have been reported as lost in slimes during processing. The chromite content of these tailings is typically 10-20% Cr2O3 and accumulates into a large stockpile/pond. A chromite concentrator project in Canada, considers a cut-off grade of 20% Cr2O3. This indicates further processing might be required to recover chromite from low-grade stockpile when the high-grade deposits are depleted. Low-grade ores normally indicates disseminated chromite ores with low liberation and consequently fine comminution. This paper reviews the techniques for treating chromite from fine material and provides some examples of successful operations in fine chromite recovery. Beneficiation techniques for fine particles include gravity separation, magnetic separation, and flotation. Several case studies are presented here that used one of the aforementioned methods or a combination of them.INTRODUCTIONChromium is one of the essential element and important material for production of ferrochrome alloys and special steel. Chromium occurs as chromium spinel, a complex mineral with chemical composition of (Fe, Mg) O (Cr, Al, Fe)2 . Chromite ore is exclusively found in ultramafic igneous rocks. Major associated gangue minerals are talc, quartz, serpentine and iron oxides.Chromite is a heavy mineral, with a specific gravity in the range of 4-5, relative to associated gangue minerals in a chromite ore, which makes gravity concentration a suitable process. This is generally true for coarse particles, ranging from 1 mm to 100 mm. Typically, the ore is prepared by crushing (and grinding if necessary) to a suitable size and the material is sized for the appropriate beneficiation techniques. It is common to use heavy medium separation (e.g. dense media drums, dense media cyclones, or Dyna Whirlpool) to treat coarse size and intermediate size particles (1 – 100 mm). Intermediate and fine particles (20 – 0.1 mm) could be treated by jigs. Spirals, shaking table, sluices, and Reichert cones can upgrade fine particles. Figure 1 shows a typical chromite beneficiation process flowsheet. As can be seen, it consists of three major sections: feed preparation (crushing, screening), de-sliming, and concentration. Beneficiation recoveries range from 80 to 85%, although the ratio of upgrading is only 2 to 3."

Jan 1, 2013

By K. Duckworth

"Comparative tests of the conventional Turam survey configuration and an alternative configuration called the Tx-parallel configuration were conducted at the McClean uranium deposit in northern Saskatchewan. Both configurations detected the known conductors at the site but the alternative configuration demonstrated its particular effectiveness in the reconnaissance role. This effectiveness results from the fact that the length of Tx-parallel traversesis controlled only by the length ofthe transmitter and not by its power. In addition, the field strength along a Tx-parallel traverse is uniform unless the traverse approaches the end of the transmitter. This freedom from a strong gradient of the primary field along a Tx-parallel traverse eliminates the gradient-induced anomaly shifts which are common in conventional Turam operations. The locations of each of the McClean conductors, that were obtained from the Tx-parallel profiles, werein better agreement with the locations known from drilling than were the locations obtained from the conventional profiles. However, the conventional profiles gave better estimates of the conductance of the targets.The results obtained over the McClean conductors indicate that current gathering has a strong influence on Tx-parallel results with consequent unpredictable influence on depth and conductance estimates. However, the depth estimates obtained from the Tx-parallel data appear to be in good agreement with the known depth of the McClean south conductor. The Txparallel results provide shallow estimates of the depth of the McClean north conductor which suggest that the fracture zone above the graphitic conductor is a significant conductor as was also suggested by earlier VLF surveys.Comparison with the wide range of published geophysical test surveys for the McClean site showed that apart from the work required to lay the transmitter, the Tx-parallel mode of operation of a Turam exploration system is operationally very similar to a moving source Slingram type of survey. At the McClean test site, it provided the same depth of exploration as a conventionally deployed fixed loop transmitter."

Jan 1, 1988

By P. R. Day, W. K. Webster

"The introduction of large boreholes underground initially involved taking the techniques of open-pit bench blasting to the production stope, but with deeper boreholes and narrower stopes more controlled techniques must be developed in order to maintain good stope walls and prevent dilution of ore or structural damage to pillars due to blasting overbreak. The points discussed are drilling accuracy and drill pattern, the relationship between open-pit wall control and underground mining, the varied explosives products and initiation devices available, and some of the many ways that variations in loading, such as deck charging, etc., can produce desirable results.IntroductionThe use of large-diameter blastholes for underground mining began ten years ago and today they are widely employed in a variety of orebodies and stope configurations. These big blastholes, which range in size from 4.5 to 8 inches in diameter, were originally employed in the same manner ' as open-pit bench blasts; that is, the stope was silled out to full width and all holes were drilled vertical and parallel. This was suitable for competent, massive orebodies, however the popularity of the big drills saw their usage in more narrow stopes, often with poor ground conditions. The dipping orebodies and small drill sublevels resulted in inclined drilling.Today, there is full-ring drilling of 4.5-inch holes. Some 6.5-inch holes are drilled up to 350 feet deep. A 350-foot borehole may contain 6000 to 7000 pounds of explosive. The detonation of this size of charge weight within the confines of an underground stope can have considerable effect on the stability of stope walls and adjacent pillars. Obviously, precautions must be taken to minimize the damage which would result from the large charge weights possible with these big boreholes."

Jan 1, 1982

By J. A. McLennan, J. M. Ortiz

Nickel laterite deposits are typically formed from tropically weathered mafic-to-ultramafic complexes. The resulting nickel concentration is found within soil horizons and is mineable with regular dozer units. At the time of mining, digging elevations are needed at selective mining units (SMUs) or representative dozer regions (RDRs). Moreover, for mine planning, the costs due to dilution and lost ore require mining elevations to be specified. A conditional simulation approach is used to calculate “optimum” RDR mining elevations. Multiple realizations of the ore base surface are simulated. For a single bottom surface realization, dilution and lost ore costs are calculated over the entire vertical extent of each RDR. The optimum mining elevation is the elevation where the lowest summed cost of “accepting dilution” and “wasting ore” occurs. The reported RDR dilution is the cost of mining the volume of waste located below the bottom surface and above the optimum mining elevation. The reported RDR lost ore is the cost of not mining the volume of ore above the bottom surface and below the optimum mining elevation. For all ore bottom surface realizations, optimum RDR mining elevations and their associated dilution and lost ore costs are calculated and compiled to represent production uncertainty.

Jan 1, 2006

By O. J. C. Runnalls

"Canada became the world's largest uranium producer in 1984. That leadership position is likely to be maintained for many years into the future because of a firm production base, many undeveloped known deposits with commercial promise, and a large geologicalpotential for new discoveries.There are some uncertainties on the horizon, principally because of restrictive actions in process within the U.S.A., which are aimed at preserving a deteriorating domestic uranium industry. Should such actions result in import restrictions, for example, there would be a negative effect on foreign producers at least in the short term. Canada may avoid such difficulties under a tentative U.S.-Canada free-trade agreement where restrictions on the import of Canadian uranium into the United States would be eliminated. Over the longer term, demand for Canada's uranium resources will grow because of the foreseen growth in the world's installed nuclear power capacity. IntroductionSince the phenomenon of nuclear fission was discovered in 1938, the utilization of uranium has grown substantially. Initially, the principal use for uranium was in the production of nuclear weapons. However, once civilian nuclear power reactors began to be built in the 1950s, an increasing fraction of uranium output was directed to the production of fuel elements for use in electricity generating stations.The cumulative uranium production by those countries in the World Outside Centrally-Planned-Economies Areas, WOCA, during the period 1938 to 1985 exceeded 800 000 tonnes of uranium. Some 60% of that was mined in the United States and Canada, as indicated in Figure 1. In 1986, nearly 80% of WOCA output came from five countries, Canada, United States, South Africa, Australia, and Namibia, as indicated in Table 1 and illustrated in Figure 2.During the past decade the world annual consumption of nuclear energy has more than tripled (Fig. 3). As of December 31, 1986, the world total of nuclear power reactors had reached 394 with a total net capacity of 270 GWe. The thermal output from nuclear power plants in 1985 exceeded 60% of the energy contained in all of the oil produced that year in the Middle East. Thus, nuclear power has already become an important component in the world energy supply picture."

Jan 1, 1988

By Philip A. Dirige

This paper presents the variability of responses of paste backfill specimens that have been prepared with varying binding agent and binder combinations, when subjected to uniaxial compressive strength testing. A testing program conducted for an underground operating mine to produce cost efficient paste fill recipes using four different binding agents, in various ratios and combinations, is presented to illustrate the responses. These binding agents are Normal Portland Cement Type-10 (NPC T-10), oxidation or sulphide attack resistant binder (Binder A), replacement binder B (Binder B), and replacement binder C (Binder C). The paste fill recipes were prepared at 2, 3.5 and 5% binder content at varying binder combinations, at fixed size and tested in a Material Testing System (MTS) under constant strain rate conditions following cure times of 7, 14, 28, 56, 90, 112, 180 and 240 days. The results of tests suggested that the strength data clearly shows a trend of increasing strength with increasing binder content but not necessarily cure time. It is noted that all the blends achieved dramatic increases in strength up to 28 days of cure and then either increased or decreased moderately beyond 28 days curing, depending on the binder content and binder combination. The moderate decrease is apparent for the 2% paste fill blends and in some binder combinations of the 3.5 and 5% blends, which indicated lackluster performance beyond 28 days curing. This lackluster strength performance indicated that the binder content and combination may not be sufficient for the paste fill to achieve complete hydration and acquire adequate strength performance beyond 28 days. This study indicated that economic paste fill recipes can be designed with confidence using affordable alternative binders. However, it is noted that these alternate binders cannot be used as stand alone binders but should be used in combination with NPC to facilitate hydration of the paste fill.

May 1, 2006

By Timo Niitti, Antti Rinne, Janne Turunen, Sami Grönstrand

"This paper describes novel methods to enhance the flow dynamics of a mechanical flotation cell that can be applied to an existing installation. There are several reasons to alter the flow dynamics. The most common motivation is to improve the metallurgical performance of the cell, for instance, to improve the flotation recovery in particle size ranges that are normally difficult to recover.The flow dynamics enhancements are associated with the geometry of the rotor-stator area and additional features in the tank. The rotor-stator area has been modified to provide more concentrated turbulent kinetic energy or respectively more pumping efficiency with less attrition to the slurry. The tank can be fitted with various geometrical features, aimed to create a desired particle suspension profile. Depending on the targeted particle size range and application, badly selected or designed features can also have a negative effect on the metallurgical results.Besides new flotation equipment, the enhancements can be applied to existing flotation cell installations, thus enabling improvements in the mixing profiles, solids suspension, tank sanding and metallurgical performance of operating flotation circuits. Results of several tests carried out in existing plant operations are presented, concerning both flow variables and metallurgy.The common factor to above-mentioned enhancements is the use of modern computational fluid dynamics tools in the design phase, as well as the validation of the obtained CFD results in laboratory and production scale. Validated variables include mixing profile, power draw and local air hold-up.The paper demonstrates the effects of various flow geometries on the mixing profiles and metallurgical results of existing mechanical flotation cells. It shows how modern computational fluid dynamics analysis can be used to screen and select different approaches before carrying out costly trial-and-error experiments in plant scale."

Jan 1, 2006

By Ken Wood

"A reliable source of water of an acceptable quality is vital to the success of any mineral processing plant using wet methods. For Cerro Verde, a new 108,000 t/d copper mill in southern Peru, the main source of raw water is the Chili River. The Chili River is heavily contaminated with raw sewage, industrial wastewater and agricultural runoff, and can also receive high sediment loads during the rainy season. The initial water treatment plant could not supply design flows of water due to the exceptionally poor water quality. Problems with treated water quality caused significant difficulties with water consuming equipment, such as the plant cooling systems. This paper details the Cerro Verde water system and changes from design through to start up from a mineral processing perspective.INTRODUCTIONMining, and mineral processing in particular, is a water intensive activity. Improving water system design and practice are key strategic requirements in moving toward a more sustainable mining industry. This case study forms a basis for ongoing research into water use and reuse at mines and mineral process plants, conducted by AJ Gunson, under the supervision of Dr. Bern Klein and Dr. Marcello Veiga at the University of British Columbia. The case study material was gathered through involvement with the design, startup, and redesign of the Cerro Verde water system.Cerro Verde is a low-grade copper porphyry mine, located near the city of Arequipa in southern Peru, at an elevation approaching 2,800 m. In 1972, one of the world’s first copper Solvent Extraction – Electrowinning (SX/EW) facilities was built on the site, processing oxide ore from two main open pits. In 2004, the operator, Sociedad Minera Cerro Verde S.A.A. (SMCV), approved a 108,000 t/d expansion project to process sulfide ore reserves through a new concentrator plant. The plant was designed under extremely tight schedule and capital constraints, with a mandate to intentionally avoid any overdesign."

Jan 1, 2008

By Y. Faitakis

In the mining industry, maintenance is a key priority and a major expense. As mining equipment is large in scale, high in cost, and difficult to tow, it is key to maintain equipment on a timely basis. Breakdown in -40°C or away from a maintenance station can cause great costs in repair as well as lost production. It has often been quoted that about 5% of the North American production is lost every year due to unscheduled downtime. About one-third of the downtime is attributable to equipment failures. From this fact alone, it is evident that proper equipment maintenance can add tremendous value to the bottom line. As organizations and equipment become more sophisticated, maintenance expectations begin to evolve. This evolution can be traced through three generations: The first generation (1940?1950): A ?fix it when it broke? attitude prevailed during that time, mostly because the industry was not highly automated. The second generation (1950?1980): Automation and mechanization of the industry increased. The industry now was dependent on machines performing the majority of the work. Preventive maintenance (overhauls at fixed intervals) appeared as the first maintenance practice. Maintenance costs started to rise rapidly. The third generation (1980?): Assets become more complex. Failure modes are better understood and computerized maintenance methods are becoming mainstream. Condition-based maintenance (CBM) starts to gain ground as a cost-effective alternative, replacing the fixed interval overhauls. As corporations amalgamate and market places are becoming more complex, multi-functional teams become responsible for maintenance. At the beginning of the third generation, maintenance organizations began embracing technology to provide efficiencies in maintenance management. A strong push was made to transition from reactive maintenance to proactive maintenance. At the forefront of this push is condition-based maintenance.

Jan 1, 2004

By Y. Faitakis, G. J. Powley, C. Mackenzie

"In the mining industry, maintenance is a key priority and a major expense. As mining equipment is large in scale, high in cost, and difficult to tow, it is key to maintain equipment on a timely basis. Breakdown in -40°C or away from a maintenance station can cause great costs in repair as well as lost production.It has often been quoted that about 5% of the North American production is lost every year due to unscheduled downtime. About onethird of the downtime is attributable to equipment failures. From this fact alone, it is evident that proper equipment maintenance can add tremendous value to the bottom line. As organizations and equipment become more sophisticated, maintenance expectations begin to evolve. This evolution can be traced through three generations:The first generation (1940–1950): A “fix it when it broke” attitude prevailed during that time, mostly because the industry was not highly automated.The second generation (1950–1980): Automation and mechanization of the industry increased. The industry now was dependent on machines performing the majority of the work. Preventive maintenance (overhauls at fixed intervals) appeared as the first maintenance practice. Maintenance costs started to rise rapidly.The third generation (1980–): Assets become more complex. Failure modes are better understood and computerized maintenance methods are becoming mainstream. Condition-based maintenance (CBM) starts to gain ground as a cost-effective alternative, replacing the fixed interval overhauls. As corporations amalgamate and market places are becoming more complex multi-functional teams become responsible for maintenance.At the beginning of the third generation, maintenance organizations began embracing technology to provide efficiencies in maintenance management. A strong push was made to transition from reactive maintenance to proactive maintenance. At the forefront of this push is condition-based maintenance."

Jan 1, 2004

By Flavio Rojos-Tapia, Oscar Pereira-Cerda, Samuel Sánchez-Pino, Samuel Sánchez-Baquedano

"Pneumatic flotation was introduced to the Chilean Copper Mining Industry in 1993 by Ingeniería de Minerales S.A. (IDM). The technology is based on the designs of Dr. Rainer Imhof from Germany, who is the designer of several different types of pneumatic flotation cells, already sold through his Company Maelgwyn Mineral Service Limited (MMH). The company is represented by Ingenieria de Minerales S.A. (IDM) in South America.Pneumatic flotation, has been used in tough industrial applications .It has been successfully used for metallic ores such as copper sulphide and oxide minerals, copper slag, silica and silicates from iron magnetic preconcentrate (reverse flotation) and gold. It has also provided promising results when applied to molybdenum flotation. The latest applications, with ultrafine molybdenum particles in operating plants, is showing the V and G Cell (end model designed) as a real technological alternative to conventional flotation., The G Cell is an extremely high speed flotation machine with high selectivity which introduces the possibility of producing a final molybdenum concentrate with only one stage of cleaning. This is a completely new development in molybdenum flotation in the industrial circuit which has the potential to dramatically reduce the circulating load in the cleaning circuit. As a consequence the capital costs of future Molybdenum plants may also be reduced. The suitability of the G Cell will have to be determined on a case by case basis but it provides the metallurgist with an alternate flowsheet for consideration.The good performance of the G Cell can be explained by the high gas hold-up and very effective micro-turbulence which helps improve the attachment of solid particles to the bubbles. This technology may change our traditional concept of residence time in flotation. Additionally, the rotation phenomena introduced in the vessel of the G Cell ,creates radial separation forces which are critical to achieving a more rapid separation of the target minerals from the tailing. This results in a much reduced residence time requirement in the flotation machine. Some benefits associated with the use of the new G Cell are: less energy consumption, less maintenance costs, simple and reliable circuit to operate and a small area required for installing the circuits.As a result of the industrial experience in the Chile, the pneumatic flotation type G Cell can be regarded as a technology which must be considered as a replacement technology for the rougher and cleaner stages for fine particle flotation."

Jan 1, 2008

By K. Leung, J. E. Udd, L. B. Geller, F. Kitzinger

"Sixteen miners died tragically at the Paymaster gold mine in Timmins, Ontario, in February 1945 when a badly corroded hoist rope broke. The investigation of the Royal Commission that followed arrived at a number of recommendations (The Legislative Assembly of Ontario, 1947) aimed at avoiding future disasters of this kind. One consequence was the development and legislated use in Canada, several decades ago, of powerful electromagnetic (EM) instruments for the non-destructive testing of mine shaft wire ropes. The authors have been involved for many years in the design, production, and testing of EM instruments (Geller and Udd, 1990, 1992; Geller and Kitzinger, 1991; Geller et al., 1992). Since the mid-1990s, particular attention was paid to the design and operational results obtained from the computer controlled portable MagnographTM II wire rope tester (Geller et al., 1995, 1998).In the present paper, the authors summarize further hardware- and software-related developments of this instrument. Further, an account is given of the results obtained from the most recent design known as the Perma- ScanTM testing system. This is also a computerized dual-function system. In it, however, the sensor head is designed primarily, if not solely, for permanent installation and for remotely controlled operation. This represents a basic departure from traditional designs, which were intended for ad hoc temporary installations. The remote-controlled instrument described in this paper has now been in operational use for more than four years."

Jan 1, 2003

By A. Takala, B Nielson, J. Schunicht

"Pre-concentration in minerals processing presents clear advantages in energy efficiency, water efficiency, reduction of consumables and minimization of capital and operating costs. Outotec’s sorting solutions are powered by Tomra Sorting in order to achieve pre-concentration of concentrator feed in a variety of mineral processing applications. Sensor based sorting combines advanced sensors with rapid computational evaluation and mechanical separation of valuable material from waste and/or gangue. Modern sensor based sorting machines typically use fine air jets to propel individual rocks, thus optimizing recovery and minimizing “mis-sorting”.Gold is generally present in such low concentrations that sensors suitable for ore sorting cannot directly detect it. Therefore, in order to sort gold ore, properties of associated host rock are used. Free and sulphidic gold is often hosted on the quartz-host rock contact zone. Laser scattering effect can be used to detect the surfaces of quartz and composite quartz-host rock particles for subsequent sorting with very high recovery of 95 to 99%. In addition, ore often preferentially fractures along the quartz-host rock contact zone in the crushing circuit. This behavior helps because it liberates more quartz for detection.The feasibility of sorting is investigated for four gold projects in Northern Europe with similar mineralogy. This includes geometallurgical evaluation, amenability testing, small scale “mini-bulk” factory testing in full scale sensor based sorting. The results of the various tests are presented and basic feasibility demonstrated with information on flow sheet development. In addition, the amenability process is evaluated and recommendations made for future projects."

Jan 1, 2017

By Manuel Sanchez, Marcial Medina, Matt Hurley, Hugo Granados, Pramod Kumar, Raj Rajamani, Jose A. Delgadillo

"Large-diameter ball mills have traditionally used steel liners—steel being a highly durable material that can be shaped into any desired geometry, among which the double-wave has been the preferred design. Such a design produces a purely cascading charge motion, which is ideal for the shearing action needed to produce a finer product. Today, however, rubber liners, which have been in existence for over forty years, are now preferred over traditional steel, largely because they weigh less and are easier to maintain. In this paper, we show the operating data from the Hudbay Minerals’ Constancia Mine, wherein the liners on a 26-by-40-foot mill were changed from conventional steel liners to PolyStl™ liners. It is then shown that this change reduced the amount of energy consumed whilst being able to maintain previous grind and throughput levels. The design is verified via discrete element simulations.IntroductionThe Constancia Mine (“Our Business: Peru,” 2016) is located in the southeastern Andes of Peru, at an elevation of approximately 4,200 m. It can be accessed via the CU-126 road, about 95 km from the town of Espinar in Espinar Province. The mine also contains both the Constancia and Pampacancha deposits in the Province of Chumbivilcas. Hudbay Minerals, Inc. acquired the mine in 2011, through the purchase of Norsemont Mining, Inc. and currently retains sole ownership of the property. Production of the Constancia Mine began in 2014, with commercial production levels being achieved in April 2015.The Constancia and Pampacancha deposits primarily include hypogene, supergene, and skarn ores. The Mine’s main products, however, are copper concentrate, with silver contents, and molybdenum concentrate. These mineral reserves are expected to last approximately 22 years. Constancia’s open-pit mine supplies a processing plant that is designed for 81,900 metric tons per day of throughput. Average annual copper production is estimated to be 82,000 mT (contained metal in concentrate). Actual plant production can be found in Table 1."

Jan 1, 2017

By W. Duyvesteyn, B. Sabacky, T. Spitler, D. Verhulst

"The Altair TiO2 pigment process is based on hydrochloric acid leaching of ilmenite at high-acid concentration. Titanium is transferred by solvent extraction into a high-purity aqueous stream with a high titanium concentration. HCl gas is recovered by pressure-swing distillation and is used to regenerate the leaching solution.A new method of TiO2 recovery in dense film with simultaneous dehydration and hydrolysis provides great flexibility in adjusting the characteristics of the TiO2 pigment product.Modifications of this method lead to a flexible, low-cost, high-tonnage process first for the production of nano-sized TiO2, and later for stabilized zirconia-based nanomaterials and nano-sized titanates.IntroductionProcesses for the production of TiO2 from ore by a hydrochloric acid route have been proposed in the past. Most of these processes dissolve impurities and recover TiO2 as a residue or as a hydrolyzed phase in the original solution (Turner, 1948; Berkovich, 1975; Morris, 1982; Judd, 1986; Chao, 1993). Solvent extraction of titanium after leaching in aqueous HCl has also been studied (Tsuchida et al., 1982; Narita et al., 1983) or at least mentioned as an alternative (Ellis, 1963). A number of small-scale studies on leaching and solvent extraction in both sulphuric and hydrochloric systems have appeared recently (John et al., 1999; Lanyon et al., 1999; Sole et al., 1999. As far as we know, only Kerr-McGee (Morris, 1982) and a plant in India and one in Malaysia use a hydrochloric acid route (20 wt% HCl) to commercially produce synthetic rutile.The Altair process originated in a search for an economical method to treat high-magnesium ilmenite deposits, while avoiding the production of a waste metal salt by-product. The first attempts aimed at producing pure TiO2 by leaching out the impurities. Further work centred on completely dissolving the ilmenite in concentrated hydrochloric acid and reprecipitating TiO2. To decrease the impurity level in the product, solvent extraction of titanium into a purified stream was introduced. It also became clear that to take full advantage of the increase in leaching efficiency provided by concentrated acid, it was necessary to regenerate HCl gas."

Jan 1, 2002