Search Documents

By Mark Johnson, Mathew Janes

"The Resonator RD 260 Resonant Pile Driver delivers ground disturbance free, high production pile driving. The Resonator has recently been used on numerous production pile driving sites in the Netherlands and Melbourne, Australia to drive piles in sensitive areas where conventional pile drivers could not be used. Two case histories are provide in this paper which demonstrate the features and benefits of Resonant pile installation.. In the Netherlands the Resonator RD 260 was used at the Vopak Oil Storage facility in the Port of Rotterdam to install pipe and sheet pile within an active pumping gallery. The site demanded vibration free pile installation to construct a cofferdam within sensitive, highly valued assets. Access was an issue and schedule demands were stringent as shutdown windows were narrow. The RD 260 provided ground disturbance free piling immediately adjacent to fragile structures. At Vopak the only site access was using a large crane positioned over 40 m from the location of pile driving. Driving was conducted amongst 900 mm dia pipes carrying heated crude oil.In Melbourne the RD 260 was used to drive GU 18 sheet piling adjacent to light rail easements. The project was the first of many grade separations being constructed within Melbourne urban areas to lower the light rail and provide quieter rapid transit. The original trial used an RGT MR105 series vibrator but noise and vibration criteria were exceeded. The RD 260 was brought in for a trial and performed with high production and produced negligible ground vibration. Up to 17 sheet piles 14 m in length were driven in a 2.5 hour window during the trial.IntroductionThe Resonant Pile Driving method is gaining acceptance around the world as a new method to rapidly drive piles free of ground borne vibrations. The high frequency vibrator resonates the pile, essentially turning the pile into a spring, to excite the toe of the pile with high accelerations and low amplitude. High acceleration with low amplitude generates high penetration rates but the high frequency stress waves are quickly dissipated in the soil. Typically ground borne vibrations are measured at below 1 mm/sec within 1 to 5 m of the pile. The Resonant method can drive a pile next to a glass of wine, without spilling, as has been demonstrated on numerous piling sites.How Does Resonance Work?The Resonant method uses a hydraulic piston - cylinder geometry to generate high magnitude, high frequency oscillating force. This is a very different mechanism than the eccentric mass technology used in conventional and variable moment vibrators.A unique valve geometry achieves the high frequency flow switching necessary to oscillate the hydraulic piston at up to 180 Hz (10800 VPM). The valve is controlled electronically for maximum accuracy of the desired frequency. The volume of hydraulic oil delivered through the valve to the piston (flow rate) determines the amplitude while the hydraulic pressure determines the peak force."

Jan 1, 1900

By Jon E. Bischoff

Construction of a secondary clarifier on the banks of Rainy River, Northern Minnesota, required the driving of H-piles 14HP102 to a sloping, very strong bedrock through thick deposits of soft and medium stiff soils. Pile toe protection, APF Hardbite HP 77750, was specified to prevent damage to the pile toe and to enable the pile toe to bite into the bedrock surface. The toe protection worked well for bedrock sloping less than 2H:1V. However, where the bedrock was steeper, the piles experienced damage and failed to reach bearing. In most cases, the also the replacement pile failed. Pile Driving Analyzer measurements showed that on encountering the bedrock, the pile toe reflection, which at first was sound, deteriorated indicating pile toe damage. Extraction for visual inspection showed that the failed piles were bent and had deformed pile shoes. In areas of steeply sloping bedrock and for replacement piles, an alternative shoe, the Scanpile Herkules rock shoe, was employed. This pile shoe proved to be able to secure the pile toe into the rock and to eliminate the problem. The costs of the Herkules rock shoe considering price, shipping, and attaching, were about equal with the Hardbite shoe.

Jan 1, 1993

By Jakub Szary

Excavation and shoring adjacent to the above-grade Gilmore train station and elevated guideway was undertaken in 2019. A perimeter secant pile cut-off wall was constructed to a depth 37 m (121 ft) below ground surface consisting of 1.0 m (3.3 ft) diameter drilled piles spaced 750 mm (2.5 ft) on-center, tied back with soil anchors, and reinforced with W610 steel sections every 4th pile. A bracing/jacking system was also constructed to support 3 free-standing guideway caissons within the excavation. An automated instrumentation program was installed to monitor movements of shoring walls and train infrastructure in real time and consisted of a robotic total station, inclinometers, tiltmeters, strain gauges, extensometers, and anchor load cells. Baseline monitoring was able to establish diurnal and seasonal movements within the structure, strongly correlated with temperature. The system actively monitored various shoring elements and train infrastructure in real time and alerted the project team when values exceeded predetermined threshold values. Remote reconfiguration of the automated system allowed for more frequent monitoring during jacking of Pier 29 in March 2022. Monitoring data was in agreeance with on-site manual surveying results and jacking dial gauges, and proved to be a reliable monitoring system for construction applications.

Sep 1, 2022

By R. A. Fraser

Large diameter (1.0 to 2.5m) bored piles have been widely used to support buildings and elevated roadways in Hong Kong. Most of these piles are founded on a hard bearing stratum such as granitic or volcanic bedrock, in the newly reclaimed areas along the water-front, the bedrock stratum can be as deep as 70-80 metres below ground surface, and construction of bored piles to bedrock in this case is difficult and unjustified. Nevertheless, Building Ordinance Regulations in Hong Kong require piles to be founded on bedrock. To overcome this problem for elevated roadways, trial piles have been designed founded on dense, completely decomposed granite. A number of piles have been constructed and subsequently load-tested to allow the rate of mobilisation of skin friction to be measured. This paper outlines the design, construction and testing method, and comments on the test results from several trial piles. GEOLOCICAL CONDITIONS The geology of Hong Kong consists predominantly of acid volcanic rocks intruded by granite. The granite has been deeply weathered, and variations in sea level have produced a drowned coastline with sequences of alluvial, colluvial and marine deposits overlying the weathered bedrock. Reclamation has extended this coastline. Typical site conditions are described later in the paper.

Jan 1, 2010

By Rasin Duzceer

In this paper, the results of pile load test on 24 piles from twelve sites are presented. The pile load tests were performed on 14 driven and 10 bored piles of varying diameters and lengths installed in different ground conditions in Turkey, Saudi Arabia and Kazakhstan. The purpose of this study is to evaluate and compare the axial capacity of the piles obtained using pile load test interpretation methods. Davisson, Brinch Hansen %80, Chin-Kondner, Shen-Niu, De-Beer, Housel, Mazurkiewicz, Fuller-Hoy, Brinch- Hansen (90%), Corps of Engineers, Butler Hoy and Tangent Intersection methods were used to determine the axial capacity of the piles. Static analysis using FHWA method was performed to predict the axial capacity of the piles. A statistical analysis was performed to compare and quantify the load test interpretation methods. The ratio of interpreted (Qi) to predicted (Qp) pile capacity was compared for each method. For each pile load test and for each interpretation method, the mean and coefficient of variation of (Qi)/ (Qp) were calculated. Among twelve methods investigated, the highest Qi/Qp value was obtained as 1.37 for Chin-Kondner method whereas the lowest Qi/Qp ratio of 0.70 was obtained from De Beer method.

Jan 1, 2002

By Prof. Dr. -Ing. habil. Sascha Henke, Johannes Beck

The growth of Building Information Modeling (BIM) during recent years opens possibilities for integrating new digitally driven design approaches. While parametric design and algorithmic design slowly gains popularity in numerous ACE-applications, e.g. bridge design, it is rarely used by geotechnical professionals. This article presents an approach for implementation of parametric design in the BIM-based geotechnical design process. The methodology is applied to pile design and enables a real time design analysis according to DIN EN 1997-1 and EA-Pfähle 2012 considering boundary conditions such as pile position and layout, pile geometry, soil stratification and soil properties. By using intelligent attributes and scripts to control, calculate and assign them, the design analysis is directly executed in the BIM-software environment, in this case Autodesk Revit with Dynamo. This BIM integrated design approach allows multi-criteria evaluations of pile designs using aspects such as costs, environmental impact or constructability in addition to the commonly examined structural analysis criteria. As the proposed models are fully parametric, generative optimization algorithms can be applied to identify the ideal design for the entirety and each of the piles. Finally, the potential and limits of this methodology with respect to modeling, analysis, simulation and optimization are discussed.

May 1, 2022

By Bryan Bet

Retaining wall systems of soldier pile ground anchors (SPGAs) have been used for many decades to stabilize landslide activity. Due to successful use of these walls to address slope instability on the California state highway system, their use has expanded to include larger, more complex landslide mitigations. The increase in size and scope of SPGA wall applications, combined with more stringent seismic design standards, have created new and unique challenges for design and construction. Constructability issues are revealing themselves in real time in Northern California, where the California Department of Transportation (Caltrans) recently completed two large SPGA wall projects on state highways: the Peregrine Slide Project in inland Mendocino County, and the Westport Slide Complex located along coastal Highway 1. Each presented unique construction challenges that needed to be overcome quickly to make the projects successful. This article highlights some construction difficulties encountered on these projects, in greater depth, than what I covered last summer at DFI's S3: Slopes, Slides and Stabiliza- tion conference in San Francisco. Also covered are what steps were taken to overcome these difficulties, and mitigation advice for future wall designs. Specifically, ground anchor installation interference, ground anchor elongation variance, and difficulties with large diameter ground anchor drilled holes will be discussed.

Jul 1, 2022

By Stephan Fisch, Franz-Werner Gerressen

"The use of cut-off-walls (COW) for the open pit coal mines has been used for decades. They have been used to reduce the negative hydraulic impact to the surrounding area caused by the open pit mining. The pile-guided trench cutting system is a worldwide unique technique, originally developed by the engineers of the mining companies themselves. It guarantees a continuous, joint free, COW during a continuous installation process. At this specific site in Welzow, this technique has been pushed to new limits in order to address the local lake region. Depth capability has been designed to about 430 ft (130m), proven are already depth of about 360 ft (110m) at a constant trench width of 39 inch (1000 mm). This project is approximately. 6.8 miles (11 km) long of COW, scheduled to be completed in 12 years period. About 2.05 miles (3.3km) have been installed, which is equivalent of about 3.5 Million ft² (330,000 m²). The system flushes special clay which forms a filter crust at the inner surface of the trench. Only natural clay resources used, in order to achieve the cut-off effect (colmation effect). The paper explains the installation process of the cut-off-wall as well as the equipment systems developed specifically for this project. After a successful start of the first phase of the project, the next step in the advancement of the equipment is already underway to enable the installation of greater depth to approximately 490 ft (150 m +) and beyond. The next generation equipment system is scheduled to start operation around 2018 INTRODUCTIONThis Serbian saying “Bóh je stworil Lužicu a cert je zaryl brunicu – God created Lusatia and the devil buried brown coal underneath it.” captures local communities’ ambivalence towards lignite.Lusatia is an almost entirely flat stretch of land between the Elbe and Neiße rivers dominated by glacial sands. On the surface, the heathland and woodland is hardly noteworthy. However, three large lignite mining regions, two in Brandenburg and one in Saxony, in the east part of Germany, divert the attention to underground level, down to depths of up to 120 meters. Here, seams crisscross the earth like ribbons. They were formed in the Tertiary around 17 million years ago.The mining of the lignite started almost 200 years ago. To enable open pit mining, a suitable dewatering system was required. At first, wells and drainage system were used. With the increasing demand to go deeper to enable full use of the existing resources with greater mining depth, a decision taken back in the 60th of the last century, the amount of water which had to be pumped increased dramatically. In peak times, approx. 1.57 Billion cubic yards per year (1.2 Billion m³/year) had to be pumped. This led to a lowering of the groundwater level for up to 230 ft (70 m), impacting the regional lake landscape. In order to reduce the influence on the water balance, and bring the water level back to pre1970th, a first development took place to implement the use of specific COW system to depth of about 147 ft (45m)."

Jan 1, 2017

By A. Felipe Uribe-Henao, Camilo Ballesteros, Luis G. Arboleda-Monsalve, David G. Zapata-Medina

Conventional excavation analysis based on total or effective stress methods can result in inaccurate estimation of ground movements when impervious soil conditions or rapid excavation sequences are not found in the excavation (i.e., assumption of undrained response is not valid). The influence of excavation rate, hydraulic conductivity, and excavation geometry on the fully coupled solid-fluid behavior of a braced excavation in cohesive soils are studied parametrically using PLAXIS2D. The coupled excavation analysis is performed using the Hypoplasticity clay model to reproduce the constitutive behavior of soil and the poro-elasticity Biot’s theory to account for changes in pore water pressure due to deformations in the soil skeleton. Results obtained from the parametric studies indicate that excavation rates to hydraulic conductivity ratios, ER/k, smaller than 0.1 and larger than 104 can be used as limits for drained and undrained analyses, respectively. In practical applications, undrained and partially drained excavation analysis with ER/k larger than 102 resulted in a similar ground deformation. However, smaller ER/k ratios demand fully coupled solid-fluid analysis. An analytical method aimed at predicting excess pore water pressures and determining the required type of analysis associated with soil and excavation conditions, e.g., drained, partially drained, and undrained analysis, is proposed herein to accurately estimate the ground movements induced by the excavation.

By José Carlos A. Cintra

This paper addresses a new experimental procedure to measure the shaft friction and the base resistance of bored piles during static load tests. It is proposed that a set of polystyrene foam discs, placed between the shaft and the base of the pile, be used instead of the usual instrumentation. Throughout the initial stages of the loading test, the foam discs will allow only the mobilization of the shaft friction. The load x settlement curve clearly shows that the shaft friction vanishes at low settlement values. As the load test proceeds, the base resistance is also mobilized. This procedure was used in two belled piles bored at the Experimental Foundation Field of the University of São Paulo, at São Carlos, Brazil. Both piles were 8 m long and had a shaft diameter of 0.6 m. The enlarged base had a diameter of 1.5 m and a height of 0.9 m. Twenty foam discs with a thickness of 20 mm each were placed between the enlarged base and the shaft of the pile. The load tests indicated ultimate shaft frictions of 28 and 30 kPa for measured settlements of 8.98 and 7.39 mm. Base resistance values at failure were 617 and 499 kPa, for a chosen settlement of 10% of the pile base diameter. The proposed approach seems to be straightforward, efficient and inexpensive.

Jan 1, 2002

By M. Hesham El Naggar, Maged A. Abdlrahem

"Hollow bar micropiles have constructional advantages such as: fast and low-noise and low vibration installation process and small installation equipment, which allow access to tight places. In addition, they have efficient load transfer mechanism, which facilitates carrying considerable load in compression and tension. The common practice is to use diameter ratio of drill bit/ hollow bar (Db/Dh) around 2 in their construction, and they are typically designed assuming type B as classified by the Federal Highway Administration (FHWA). In this paper, the performance and capacity of Hollow bar micropile with different (Db/Dh) ratios are investigated. Full-scale micropiles were installed at a site in Ontario, Canada, and were tested in order to evaluate the uplift performance of Hollow bar micropile with different(Db/Dh) ratios. Two micropiles with two different ratios 2.25 and 3 were constructed and tested. The total length of the micropiles was 6m with embedded length of 5.75m. The soil at the site was primarily medium dense to dense sand. The results of the load tests are presented and discussed. It was found that the uplift capacity of the micropile increased by about 19.5% as Db/Dh increased from 2.25 to 3.INTRODUCTIONMicropile is a small diameter, less than 300 mm, drilled and grouted pile and is typically reinforced according to Federal Highway Administration (FHWA, 2005). The technology of micropile was introduced in North America in 1970’s, but the growth in the east coast of United State was intense compared to all other cities around the globe (Bruce and Nicholson, 1989). Nowadays, micropile construction is used extensively worldwide as a viable solution that offers several advantages such as fast installation in low headroom, minimal disturbance to the adjacent structure efficient load transfer due to high grout to ground bond strength. As the method of grouting has major influence on the grout – ground bond strength, FHWA has classified the micropiles into four categories. Type A: the grout is placed under gravity and no pressure is required. Type B: The grout is typically pressurized under a pressure range from 0.5 to 1 MPa as the temporary casing is withdrawn. Type C: the grout is placed in two-step process. First, the grout is poured under gravity only as in Type A. Before the hardening of the grout, similar grout is pressured of at least 1MPa without the use of packer. Type D: Like Type C, it is a two – step process, the grout is placed under gravity as in Type A and sometimes pressurized as in Type B. After hardening of the initial grout, additional grout is pressurized between 2 to 9 MPa through sleeved pipe by using packers, as many times as needed. According to this classification, hollow bar micropile is usually designated as Type B. However, the construction technique is completely different from Type B. Recently; there is a trend to supplement the four types of micropiles by Type E as represent to hollow bar micropile (Timothy et al, 2012). The construction method of hollow bar micropile involves two main stages which can be performed in one–step process: advancing the drilling bit attached to a threaded hollow bar to the required depth; and pressurizing the grout through nozzles of the drill bit."

Jan 1, 2016

By Cau T. Bui

Thanks to Doi-moi (renovation) policy, many great bridges were constructed in Vietnam to meet demands of her booming economy in the recent decade and deep foundation structures were the only alternatives for the foundations of these great bridges. The deep foundation structures were constructed by modern technologies and almost of all these deep foundation structures were designed by foreign companies and carried out by Vietnamese workers and engineers under supervision of foreign experts. Beside successes, there were several failure cases in which the collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation killing 54 workers and seriously injuring 80 other workers was the most serious. This paper introduces construction techniques of the deep foundation structures applied to building of great bridges in Vietnam recently. It will especially focus on two failure cases: 1) collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation and 2) failure of drilled shaft foundation of Thanh-tri bridge due to poor construction technique and management. These two failure cases were greatly concerned by both bridge specialists and the public. Reasons of and lessons from these two failure cases will be carefully discussed. From the two failure cases, this paper will draw some lessons that should be important issues to be seriously paid attention when designing and constructing deep foundations in Vietnam.

Jan 1, 2008

By Wolfgang G. Brunner

In the far north of Uttar Pradesh Province in the Indian Himalayas, the 280 MW Dhauliganga hydroelectric power plant is under construction by National Hydroelectric Power Corporation (NHPC), a state- owned enterprise, and a joint venture of Kajima Corporation of Tokyo and Daewoo Corporation of Seoul. This project sets out to develop the lower section of the mountain cascade of the Dhauliganga River, a tributary of the Sarda River, with a 311 m gross head. The 1360 km2 mountainous catchment area is bounded in the north- east by the Chinese border and in the south- east by the Nepalese border. The dam project is located in a remote area north of the principal town of Darchula of the upper Sarda valley, which is one of the seismically most active regions of India. The 56 m high rock fill dam, which will be the first of its kind in India, is faced with concrete and has a 1 m thick, at its crown 270 m long and over 70 m deep cut- off wall of plastic concrete below its toe. The cut- off wall, with a total area of 7500 m2, is constructed by a combination of Bauer hydraulic grabs, assisted by chisels and a Bauer BC 40 cutter which enables the overlapping joint system to be installed, guarantees optimum verticality and enables the cut- off to be keyed into the bedrock formation.

Jan 1, 2004

By Bill Zietlow

A micropile and soil nail underpinning system was installed to support a building immediately adjacent to a 25-ft deep excavation in downtown Salt Lake City, Utah. Both the building and the underpinning were instrumented to monitor deflections, rotation and crack growth. The underpinned structure consisted of a two story concrete masonry unit (CMU) building founded on shallow spread footings attached to a concrete high-rise building on spread footing two floors below grade. The face of the excavation was 10 in. in front of the underpinned building foundation wall. The underpinning system consisted of small diameter hollow bar micropiles installed with injection grouting techniques below the bottom of the excavation and attached to the underpinned structure by a concrete pile cap doweled into the existing footing. The lateral loads imposed by the soil under the underpinned structure were designed to be supported by the soil nail wall installed through the micropiles during excavation. The settlement monitoring instruments consisted of crack gages, optical survey prisms, high sensitivity vibrating wire water levels and biaxial vibrating wire tilt meters. They recorded maximum movements of approximately 0.1 in. of settlement, 0.05 deg. rotation (top of wall rotating away from excavation) and up to 0.08 in. of crack opening during the excavation until one month after the soil nails and shotcrete facing were completely installed. This movement was well within both the estimated settlement and the estimated settlement tolerance of the underpinned structure.

Jan 1, 2008

By Daniel Levacher

Pile load tests in site require extensive means of action and time. To get outstanding tests, the environmental test conditions must be perfectly known and acceptable. They concern the support installation, the loading, the access and instrumentation site conditions and the economical aspects. In particular cases as offshore areas, the load tests are not feasible. Moreover the variability of soil characteristics limits the interpretation results at the considered tested site. The use of centrifuge modellling offers an other way to study the loaded pile behaviours. Centrifuge tests lead to parametric approaches which constitute for geotechnical engineers an important data base tor recommendations and design codes. To accurately simulate pile behaviours by checking similitude laws linked to the studied problems, the installation of model-piles must be also representative of the in-situ piles. Driven piles account for a large part of the piles installed through the world, mainly for offshore or harbour constructions. So, to explore driven pile problems by centrifuge tests, miniature pile driving hammers must be developed and tested under macro-gravities. The paper describes two types of these ones in details. They are commonly used at the centrifuge centre of the Laboratoire Central des Ponts et Chaussées - (LCPC) - [Réf. 1] for different deep foundations researches. Performances and limitations are given for both miniature pile drivers and some results from their use are presented to illustrate the suitability of these apparatus.

Jan 1, 1996

By Saba Mohan

This study presents results based on the Pile Installation Demonstration Project (PIDP) that was conducted as a part of the East Span San Francisco-Oakland Bay Bridge Seismic Safety Project. For the three full-scale pile installations, two different high-energy hydraulic hammers were selected for the installation. However, these hammers may not have sufficient energy to drive these large diameter piles at their ultimate capacity following long-term set-up. Nevertheless, these hammers were selected because, soil plug behavior, the generation of excess pore pressures and remolding of soil during driving were expected to reduce the shaft and end bearing resistance, and therefore reduce the energy required to drive these piles to design penetration. Data collected during continuous installation driving and after a series of re-strikes at different set-up times ranging from 1 to 33 days were used as input data for CAPWAP. These results were used to estimate the soil resistance along the pile length and at the toe of the pile, and the soil pile set-up behavior. Validity of the procedures used to predict the soil resistance to driving and predicted blow counts were verified with the field observed blow counts and the energy that was delivered to the pile. Based on combined CAPWAP analyses, the soil pile set-up with time was estimated and compared with results of other methods currently available in the literature for predicting the soil pile set-up rate.

Jan 1, 2002

By Gianni O. Chieruzzi

A 400 MW, gas-fed power plant on floating piles and piled raft foundations was constructed in the Province of Moskovskaya, Russia in 2008. The subsurface is characterized by fill underlain by loose to medium dense alluvial deposits, with peat and clay interbeds, a stiff to hard, highly plastic, silty clay stratum of glacial origin, and a stratum of very dense, varved interbeds of sand and silt. More than 800, drilled concrete piles were constructed at the site. The pile length ranged from 15 to 23 meters below existing surface grade, and the pile diameter ranged from 0.9 to 1 meter. Initial analyses by others predicted total power plant settlements of 3 to 4 cm when subjected to the permanent loading conditions. Under a peer review process for the equipment supplier, subsurface investigation and testing were performed to verify the consolidation parameters used for foundation design of the power plant foundation. The parameters obtained in this investigation were used in the 3-D finite-element model ELPLA as inputs for the settlement analysis of the turbine building and power island. The ELPA analyses predicted settlements on the order of 7 cm over a period of 30 years. The actual settlements after two years of monitoring were compared against the model predictions. The rate of settlement and the recompression index were both underestimated in our model. The measured settlements have enabled us to calibrate both of these model parameters so that the model better matches the data.

By Dharmil Patel, Michael J. Chow

"Construction progress is nearing completion at a Brownfield Site for a 100,000sf mixed-use 10 story building plus cellar for Silver Star Motors including a two-floor pre-owned Mercedes Benz showroom; high-end residential rental studios, 1, 2, and 3 bedroom apartments; and penthouses on the upper two floors. Excavation through impacted soil extended to 15ft depth. Project is approximately 7 ft north of a NYCT subway station, portions of the SOE are within inches of a 6ft diameter NYCDEP Sewer, and cellar extends below the depth of adjacent structures, requiring over 200 lf of underpinning.A complex series of earth retention systems was utilized consisting of underpinning, drilled-in soldier piles (micro-piles), timber/concrete lagging, soil anchors and inclined rakers supported by a partially constructed foundation mat. Foundation mat subgrade was approximately 4 ft below the groundwater level creating more challenges during underpinning and achieving suitable foundation subgrades. All construction was undertaken on a non-union basis.This paper describes the design, construction, and lessons learned for the multiple earth retention systems, Brownfield Remediation requirements, instrumentation, and monitoring used to manage complications of building adjacent to an active subway station, in close proximity to existing utilities, with underpinning and mat foundation installation below the water table.Results of the instrumentation program are summarized which utilized an AMTS, monitoring prisms on adjacent structures, automated seismographs, and manual NYCT surveys."

Jan 1, 2016

By Kyle M. Rollins

To improve our understanding of lateral resistance of pile groups, a series of lateral load tests were performed on a full-scale pile group using both static and dynamic loads. The pile group consisted of nine 0.6 m-diameter steel pipe piles driven into clay. During the static tests, the load was cycled fifteen times to evaluate the drop in lateral resistance that would occur due to repeated loading and the formation of a gap. The peak load typically decreased by about 15% from the initial cycle to the last cycle. The load carried by each pile was also measured and there was a significant drop in resistance for the piles in the trailing row relative to the leading row. The dynamic force was applied using the Statnamic loading system which produced a lateral force of 3500 kN (787 kips) in about 0.1 seconds. In two cases, dynamic loads were applied following application of 15 static load cycles. In these cases, the dynamic lateral resistance was about the same as the static resistance, likely due to gaps around the pile. In three other cases, the dynamic force was applied prior to the cyclic loading. In these cases, the dynamic resistance was 30 to 60% higher than the static resistance. Simplified analyses suggest that the difference in resistance could be attributed to damping produced by the soil surrounding the piles during the virgin loading.

Jan 1, 2002

By W. Morgan NeSmith

The city of Kansas City, Missouri, is replacing its original airport, con- structed in 1972 as a "drive-to-the- gate" facility, with a modern, single- terminal facility with just over 1 million sq ft (92,903 sq m) in area along with an adjacent 6,300-space parking structure. It is the largest infrastructure project in the city's history. The project team designed and oversaw the installation of 12-24 in (305-610 mm) diameter augered cast- in-place (ACIP) piles to a range of depths with the pile toes located in underlying alluvial clay, weathered shale or on intact limestone, depending on the required loads at each column location. The specific ACIP piles used were auger pressure grouted (APG) piles. Additional information regarding the ACIP pile installation process can be found in the Augered Cast-in-Place Pile Manual, Third Edition (2016) prepared by the DFI Augered Cast-in-Place and Drilled Displacement Pile Committee. This article includes a summary of the subsurface conditions, the foundation support requirements, the extensive performance test program - started before production installation but not completed until well into production phase of the project - and the resulting production pile installation require- ments. The approach resulted in about $700,000 in foundation program savings to the city. The reduced con- struction time of about 10% less than originally estimated also added to the overall savings beyond the direct foundation savings.

Oct 1, 2022