Search Documents

By Monique Nykamp

"INTRODUCTIONTerminal 46 is located just south of downtown Seattle, and is one of the Port of Seattle’s busiest container terminals. The Terminal 46 Redevelopment Project was undertaken to replace the existing 15-m-wide (50 ft) cranes along the apron with 30-m-wide (100 ft) cranes, which can unload larger, post- Panamax ships. The project included upgrading the existing waterside crane rail with new piles and constructing a new land-side rail behind the sheetpile bulkhead. The new piles had to be installed adjacent to the existing apron without causing damage, which was a signifi cant geotechnical challenge due to the soft soil conditions at the site. An instrumentation program performed during the test pile program evaluated this challenge and allowed for the development of specifi c production pile installation procedures that had the least possible effect on construction costs and schedule.SITE HISTORYThe site lies along the west side of Elliott Bay, north of the mouth of the Duwamish Waterway. Prior to development, this area was part of the tide fl ats where the Duwamish River drained into Elliott Bay. Prior to 1970, there were several existing timber piers and structures in the area. In the 1970s, the Port of Seattle constructed a 900-m-long (3,000 ft), 30- m-wide (100 ft) apron to support fi ve, 15-m-wide (50 ft) container cranes. The contained backland area was then fi lled with dredged spoils (sand and silt with organics) and the upper 5 to 20 m (16 to 65 ft) backfi lled with sand and gravel.The existing apron was constructed using 0.4 m (16 in) octagonal prestressed concrete piles to support the precast concrete deck and crane rails. The pile-supported bents were spaced at 6.1 m (20 ft), center-to-center, along the longitudinal direction. Pile lengths typically varied from about 20 to 40 m (65 to 130 ft) with 15 to 26 m penetration below mudline (50 to 85 ft penetration). The slope below the apron was constructed at about 1.75 horizontal to 1 vertical to allow for suffi cient water depth for cargo ships. In most areas, a riprap buttress was placed at the toe of the slope. A typical cross section of the apron is shown on Figure 2.Several stability, settlement and pile driving issues arose during the original construction of T-46 (Pita, 1983). Reportedly, movement of the submarine slope occurred during pile driving, resulting in settlement behind the bulkhead. Pile driving reportedly caused settlement of adjacent piles. In addition, some piles were “running” (dropping quickly under one hammer blow) during installation."

Jan 1, 2007

By C. M. Haberfield

"1 INTRODUCTION Around the world, there is a demand for larger structures, tall buildings and large bridges. While good footing design is important for all structures, it is even more important in the case of large structures. Recent experience with footing design for tall buildings (e.g. Burj Al Alam development and Nakheel Tower in Dubai, the Gate of Kuwait in Kuwait, the City Centre Project in Bahrain and Eureka Tower and Freshwater Place in Melbourne) has shown the benefits of investing in footing planning, design and construction (Haberfield, 2011, Poulos and Bunce, 2007). The footing systems for most of these projects include the use of deep bored piles or barrettes (piles of rectangular cross-section). Many use piled rafts where the piles, while acting to support the load, are primarily used to reduce settlements. A clear understanding of the factors controlling the behaviour of the footing system is needed to enable a good engineering design to be achieved. This starts with a sound understanding of the ground characteristics and individual pile performance, including adequate collection of data and testing. The best footing solution can then be found using recent improvements in data collection and analytical techniques, complex and highly capable computer-based models and the availability of high speed computers. This paper focuses on the axial performance of deep bored piles socketed into rock – both their individual performance and their performance as part of a larger footing system. Recent research and construction practice is discussed. In practically all cases, serviceability conditions control the behaviour of the footings. Methods of establishing the parameters for input into sophisticated computer programs are described. Application of the methods to case studies is included and it is shown that the behaviour of individual piles can be closely predicted. These developments lead to lower construction costs, better constructability and shortened construction time because of the better understanding of footing behaviour. 2 FACTORS AFFECTING PERFORMANCE OF FOOTINGS ON ROCK For a typical pile-supported footing, it is necessary to consider both individual pile, pile group and raft performance. These require consideration of the behaviour of the ground immediately beneath the surface raft or footing, along the pile shaft, and at and beneath the pile toe (Figure 1). Immediately beneath the surface raft or footing, the important factors are strength for bearing capacity and stiffness for settlement and interaction effects. Along the pile shaft, of most interest are strength for bearing, excavatability and stability; stiffness for settlement and interaction effects; geology and permeability for pile stability and, most importantly, pile shaft resistance. At the pile toe all the above factors for the pile shaft are present and in addition the pile end bearing is of interest. Below the toe, stiffness for pile settlement is important to at least a depth of twice the building width."

Jan 1, 1900

By Graeme Smart, Thomas Fiala

"Yorkville Plaza II, a 40-storey signature condominium residence, is scheduled to open on Avenue Road in Toronto’s prestigious Bloor-Yorkville neighbourhood in spring 2017. In close proximity to Toronto’s subway system, the new tower requires six levels of underground parking, founded in wet, silty sand.Isherwood Geostructural Engineers (Isherwood) was retained in April 2012 by developer Camrost-Felcorp to provide a shoring and excavation solution to address the challenging site conditions. A 31-storey upscale residential building under renovation with three levels of parking, owned by Camrost-Felcorp, flanks the site on the north. Situated on the eastern border is a 7-storey building with three levels of parking. Avenue Road, a four-lane arterial road that brings heavy commuter traffic into downtown Toronto, runs along the western border, and on the southern border of the site is a busy City road that brings traffic into the popular Yorkville area. The tunnel for the Toronto Transit Commission’s (TTC) overburdened east-west subway is located 14.5 m to the south, running below an existing 26-storey neighbouring building. Electrical and communication utilities (Bell) are closely located along the southern side. Non-documented existing excavation shoring, installed in the early 1970s, on the southern and western sides compounded the difficulties presented by the TTC tunnel.This paper presents the unique, non-conventional hybrid shoring solutions Isherwood developed to address the challenges presented by the site, as well as other complications that surfaced during the project: non-encroachment requirements (no tiebacks) beneath uncooperative neighbours, tight geometry to install shoring, and Toronto’s two coldest winters in decades.THE PROJECTBecause of circumstances associated with this site, for this project Isherwood designed two unique shoring walls which drew on their experience and expertise they had gained over the last 40 years. The following is the story of this site:Yorkville is an affluent neighbourhood in the heart of Toronto with a vibrant mix of high-rise towers, residential homes, tony restaurants and flagship shops. The development requires six levels of underground parking (a 20m deep excavation), with three levels undermining the high-rise buildings to the north and east and extending into wet, silty sand.Isherwood was retained in the spring of 2012 to design the excavation shoring. Isherwood’s scope also included field support, design, verification and monitoring. Finite Element Analysis was employed to confirm Isherwood’s design and anticipated movement of the south shoring wall and the TTC subway tunnel.The existing site was severed in two, with the proposed condominium tower slated for the southern portion. On the north half of the site stands a 31-storey building (Yorkville Plaza I at 21 Avenue Road), with three levels of underground parking, sitting on belled caissons which were one foot from the back of the proposed shoring wall so this would have to be considered in relation to the design and drilling methods. Constructed in the early 1970s, Yorkville Plaza I is currently being converted from the Four Seasons hotel to luxury condominiums by Camrost-Felcorp. To the east, directly adjacent to the proposed shoring, stands a 7-storey building (164 Cumberland Road) with three levels of parking, supported on spread footings founded on stiff clayey silt. The tunnel for the TTC’s busy east-west subway, a double box structure built by cut-and-cover in the 1960s, is located 14.5 m to the south, 9 m below grade, and running below an existing 26-storey building. Bell fibre optic communication cables and electrical lines, along with storm and sanitary sewers, are situated on the south and west sides of the site, leaving limited room to install shoring. Due to the heavy volume of commuter traffic on the four-lane arterial road (Avenue Road) to the west, site access and lane closure were not permitted here."

Jan 1, 2015

By Noreen Tarac, Pablo Forgoso, Philipp Schober

A multiple use storage facility building is being developed in the Philippines on a peninsula that was reclaimed in the 1990s without any soil treatment. The subsoil now consists of loose to medium dense silty sand underlain by a soft to medium stiff clay. A liquefaction assessment by analytical methods have shown that the loose to medium dense silty sand yields a high potential for liquefaction and lateral spreading during pthe design level seismic event. To mitigate the risk of liquefaction and lateral spreading, as well as assure the slope stability of the shoreline, a solution utilizing a combination of ground improvement techniques by means of a Mixed-In-Place (MIPTM) Lattice Grid Wall and Stone Columns was developed and successfully executed. For the detailed seismic design, a Finite Element 3D analysis was undertaken to simulate static and dynamic actions on the buttress wall. The liquefaction assessment and settlement calculation were carried out based on analytical design approaches. For the execution of the Lattice Grid Wall, the Mixed-In-Place (MIPTM) method developed by BAUER Spezialtiefbau GmbH was applied. The stone columns were installed using the Wet Top Feed method.

Sep 8, 2021

By Kyle Kershaw

Micropiles are routinely used in the United States for foundation support and stabilization of slopes. In recent years, several retaining walls have been constructed using micropiles in an A-frame type configuration to support temporary and permanent excavations at sites with limited access and limited right-of-way. Typical A-frame micropile walls consist of a row of vertical micropiles at the face of the wall and a row of battered micropiles extending into the soil or rock to be retained. The two rows are then tied together with a pile cap such that the front pile acts primarily in bending and the back pile acts primarily in tension. Because of tight right-of-way constraints at a residential site in Aspen, Colorado, it was not possible to construct the wall using conventional shoring systems or micropiles in the typical A-frame configuration. Rather, the wall was designed such that the row of battered piles was installed at the wall face and the row of vertical piles was installed adjacent to the property line behind the wall. As a result of the reverse configuration of the A-frame wall, FLAC, a two-dimensional, finite difference software program, was used to model the soil-structure interaction. The final wall design consisted of both temporary and permanent retaining wall sections with maximum heights of 26 feet. Inclinometers were installed in several piles to monitor the behavior of the retaining walls during and after excavation. This paper presents an overview of the design method, a discussion of construction techniques, and a comparison between the FLAC model and the measured behavior of the wall in the field.

Jan 1, 2007

Jan 1, 1993

By Michael Shedlosky, Sonia Sorabella Swift, Nina Carney, David Tarasovic

Rigid inclusions were used to support roadway fills and mechanically stabilized earth (MSE) walls for the South Capitol Street Corridor project. The first phase of this two-phase, nearly $1 billion project will include the replacement of the Frederick Douglass Memorial Bridge, including two approach ovals east and west of the Anacostia River, the replacement of the I-295/Suitland Parkway Interchange, and the construction of several traffic ramps. The bridge itself carries over 70,000 drivers daily and is expected to open in 2021. Ground improvement is required over a portion of the project footprint. Within the ground improvement area, the construction includes MSE walls up to 35 feet high and embankment fills up to 28 feet for which CMC rigid inclusions (RIs) were used to mitigate settlement and stability. The proposed construction runs over multiple old, in-service utilities that the project requirements indicate could not tolerate any stress or settlement due to the construction. As such, solutions that spanned the utilities were required. A concrete slab of varying thickness was used to span a fragile 108-inch-diameter sewer pipeline and 48- inch-square-precast-concrete box beams were used to span twin utilities that were buried just a few feet below current working grades on site. Unreinforced RIs were used to support these structures. The center to center spacing of the RIs perpendicular to the pipe run was 26.5 ft for the concrete slab and 62 feet for the precast--concrete box beams. The axial forces on the RIs were up to 267 kips. The RIs were not structurally connected to the slab or box beams. A single-element load test was performed to confirm the load-carrying capacity of the RIs. This paper will focus on the utility protection slab over the twin utilities and provide an overview of the design of the structural and geotechnical solutions and will present the results of the load test performed. INTRODUCTION The new Frederick Douglass Memorial Bridge (FDM Bridge) and reconstruction of the Suitland Parkway/ I-295 interchange (South Capitol Project) is a part of the Anacostia Waterfront Initiative (AWI) Program, whose goal is to transform the shores of the Anacostia River. The existing FDM Bridge is approximately 70-years old and has been classified as “functionally obsolete”. The completed South Capitol Project will improve the multi-modal transportation options, increase pedestrian and vehicular safety and provide additional green space. The proposed FDM Bridge, a rendering of which is shown in Fig. 1, is designed to become a landmark bridge in the Washington, D.C. area.

Jan 1, 2019

By Allan Herse

"The years following World War II were nation building years in Australia. Soldiers returned from the European and Asian theatres of war sparking a major infrastructure construction boom. Dams and highways were built to keep up with the growth of towns and cities, which were bursting at the seams, not just from the returning soldiers settling down with their families but also from the many waves of refugees from war torn areas around the globe.The demand for electricity generation and distribution required for the growing population sparked the expansion of the national power grid with new high-voltage transmission towers appearing across the landscape. However, with an original design life of 50 years, those transmission lines constructed in the 1950s are nearing, or are at the end of, their anticipated service life.In recent years, the Australian power distribution network has changed from a period of high construction activity in greenfield high-voltage lines to a period that is now focused on reducing cost and maintaining existing assets. Replacing aboveground structural members and electrical components is relatively simple even under live conditions. However, the replacement or repair of tower foundations, many of which are in remote locations, has been a problem that has caused difficulties for power utilities trying to operate on a budget while also avoiding costly and unpopular power outages.With thousands of miles of aging transmission lines needing life extension work, Piling & Civil Australia (PCA) has developed a patented system of upgrading the foundations with micropiles while under live-line conditions without requiring costly outages. The system is seen as revolutionary by power utilities, allowing the utilities to extend the life of their existing assets until demand increases to warrant the construction of a new line. PCA has been working on a potential solution with Powerlink Queensland for the past 5 years to develop a quick and cost-effective foundation replacement system that can extend the life of its existing asset base anywhere from an additional 5 years to 50 years.With design support from Quanta Subsurface, USA, PCA recently completed the foundation replacement of 26 lattice tower foundations in the Townsville region of North Queensland. Using a steel bracket (patent pending) to connect hollow bar micropiles to the lattice towers, the installation techniques that were developed enabled the micropiles to be installed within a tolerance of less than about 3/8 in (10 mm) through the existing steel grillage foundation while maintaining live line conditions. The project was an Australian first and a trial by Powerlink for wider use within its network, and it was delivered on time and within budget at one tenth of the cost of traditional methods."

Jan 1, 2017

By Allan Herse

"The years following World War II were nation building years in Australia. Soldiers returned from the European and Asian theatres of war sparking a major infrastructure construction boom. Dams and highways were built to keep up with the growth of towns and cities, which were bursting at the seams, not just from the returning soldiers settling down with their families but also from the many waves of refugees from war torn areas around the globe.The demand for electricity generation and distribution required for the growing population sparked the expansion of the national power grid with new high-voltage transmission towers appearing across the landscape. However, with an original design life of 50 years, those transmission lines constructed in the 1950s are nearing, or are at the end of, their anticipated service life.In recent years, the Australian power distribution network has changed from a period of high construction activity in greenfield high-voltage lines to a period that is now focused on reducing cost and maintaining existing assets. Replacing aboveground structural members and electrical components is relatively simple even under live conditions. However, the replacement or repair of tower foundations, many of which are in remote locations, has been a problem that has caused difficulties for power utilities trying to operate on a budget while also avoiding costly and unpopular power outages. With thousands of miles of aging transmission lines needing life extension work, Piling & Civil Australia (PCA) has developed a patented system of upgrading the foundations with micropiles while under live-line conditions without requiring costly outages. The system is seen as revolutionary by power utilities, allowing the utilities to extend the life of their existing assets until demand increases to warrant the construction of a new line. PCA has been working on a potential solution with Powerlink Queensland for the past 5 years to develop a quick and cost-effective foundation replacement system that can extend the life of its existing asset base anywhere from an additional 5 years to 50 years.With design support from Quanta Subsurface, USA, PCA recently completed the foundation replacement of 26 lattice tower foundations in the Townsville region of North Queensland. Using a steel bracket (patent pending) to connect hollow bar micropiles to the lattice towers, the installation techniques that were developed enabled the micropiles to be installed within a tolerance of less than about 3/8 in (10 mm) through the existing steel grillage foundation while maintaining live line conditions. The project was an Australian first and a trial by Powerlink for wider use within its network, and it was delivered on time and within budget at one tenth of the cost of traditional methods."

Jan 1, 2017

By Chandramohan P. V., Ravi Kishore

"An underground reservoir was to be constructed at Doha in Qatar. Simsima lime stone is present at the bottom. When the reservoir is empty, there will be uplift at the bottom but this will change to downward load when it is full. The rock at the bottom had high bearing capacity to resist downward load. But uplift had to be resisted by piles or anchors. The reservoir has a size of 120mx80m. Shrinkage and creep of concrete coupled with thermal contraction imposed a horizontal movement of 26mm on the extreme piles. So, piles have to accommodate this as well. This unique situation needed a unique solution. The solution was to provide piles with flexible high tensile strands to take tension. An annular space near the head of the pile would facilitate horizontal movement as well. Compression load was directly passed on to the raft bearing on rock.INTRODUCTIONAn underground reservoir for storage of drinking water was to be constructed at Doha, Qatar. The reservoir was proposed to have a plan size of 120m x 80m. Clear height inside the reservoir was proposed as 17.2m, from the bottom of roof to the top of bottom raft. Overall height of the reservoir at the outlet from the top of the roof to the bottom of raft was to be 21.2m. For the sake of inspection and in order to prevent pollution from the surroundings a gallery was planned around the reservoir. This could accommodate pipelines as well. This gallery was 3.0m wide on three sides and 8.4m wide on the outlet side.The gallery had removable gratings as cover in order to facilitate maintenance. Capacity of the reservoirwas proposed to be 40million gallons. The reservoir is divided into four compartments with baffle walls in each one for water circulation. Roof of the reservoir is kept at 300mm above ground level. There are two levels of car park on top of the reservoir. Top of the reservoir roof is at +14.35. Bottom varies from - 6.68 to -7.08. Lowest water table is at +6.00. Concrete structure of the reservoir was designed by a local consultant. The Navayuga Engineering Company was entrusted with the construction. Please see Figs 1 and 2."

Jan 1, 2017

By Dario Libano, Luis Carlos Tenuta, Juliano Penteado

"Subway Line Number 4 is one of the newest additions to the Rio de Janeiro subway network. Built for the 2016 Olympic Games, the 16 km (10 mi) subway line connects the south of the city, with the famous beaches Copacabana and Ipanema, to Barra da Tijuca, west of the city, where the Olympic Village and Park are located. This new line, which is estimated to cost USD 2.2 billion, is composed of six new stations: Jardim Oceanico, São Conrado, Gavea, Antero de Quintal, Jardim de Alah (JA) and Nossa Senhora da Paz Station.Brasfond participated in the construction of foundations and retaining structures for all the stations, and each presented unique challenges. This is not surprising considering the difficulties present in a highly-dense urban environment including utilities, nearby buildings, traffic limitations and noise.Of all the stations, JA Station was the most challenging to construct. It was located in the middle of an avenue between residential high rises supported on shallow foundations as well as below sea level in sands with high groundwater. The other five stations were located in small parks and squares, with no buildings in the immediate proximity.The interaction between designer, owner, and the general and foundation contractors during execution was key in safely reducing the construction schedule. This was significant given the unforeseen construction delays the client, Linha 4 Sul JV, faced due to permitting, utility and traffic relocation so that the owner could fulfill their final goal: making the line operational by the Olympic Games. The GeologyGeologically, the state of Rio de Janeiro is formed by Pre- Cambrian crystalline basement rock. Its geological formation is very old and comprises two major orogenic cycles, a Mid-Precambrian formation, called “Transamazonian” (Proterozoic Era), and an Upper-Precambrian to Cambrian called “Brasiliano” (Proterozoic-Paleozoic). The soil structure of the city of Rio de Janeiro is represented by a core of crystalline rocks, usually granite-gneiss, covered with a layer of residual soil and/or partially weathered rock.JA Station is located in a Rio de Janeiro neighborhood called Ipanema, between the Atlantic Ocean and Lagoon Rodrigo de Freitas. Local geology is composed of a superficial soil, consisting of medium to coarse grained sands. Top of rock varied significantly from 20 m (66 ft) deep on one side of the station to 33 m (108 ft) on the other. Water is at a depth of 3 m (10 ft)."

Jan 1, 2016

By Mike Muchard

STATNAMIC load testing augmented with embedded instrumentation has been successfully used to obtain structural and geotechnical design information on large diameter spun cast concrete cylinder piles on many large marine construction projects. The paper focuses on one particularly interesting large marine project involving a new bridge to St. George Island, Florida where instrumentation and STATNAMIC load testing was used in conjunction with static load testing on high capacity piles. The information presented includes embedded instrumentation measurements taken during pile fabrication (post-tensioning), during pile driving, during static load testing, and STATNAMIC load testing. As much of this data is the first of its kind on concrete cylinder piles, it is exciting to present the foundation industry with this additional insight as to the behavior of this pile type and the accuracy of the methods used to test them.

Jan 1, 2013

By Scott Webster

Dynamic pile Monitoring Services (DMS) have been used for testing of offshore piles for several decades. However, most of this testing was to measure hammer performance and pile stresses rather than pile capacity or soil resistance. As the need for more economical solutions for foundation support increases, the use of DMS has provided a better means of evaluating in-place pile capacity for offshore structures, and therefore a method of determining pile acceptance. The authors have been involved in several offshore projects where DMS has been the primary source of data for acceptance of the driven pile foundations. The use of DMS for evaluation of offshore foundations requires considerations quite different from land applications and these considerations are often necessary for the careful and thorough analysis of the collected data in nearly real time for determination of pile acceptance. Case Method capacity estimates are often of little use due to the non-uniform cross sections of the foundation piles and their deep penetrations. Therefore, capacity assessments should be made using CAPWAP which is a signal matching program whose utility and reliability has been proven on thousands of projects every year, both on land and offshore. Depending upon the soil conditions at a given location, capacity assessment after soil setup effects may be necessary. In addition, tension capacity is often critical when pile refusal occurs significantly before the design pile penetration depth. Evaluation of uplift capacity can be accomplished by a CAPWAP analysis, which results in a total capacity prediction and its shaft resistance component. The use of hydraulic hammers for driving of these piles also adds the requirement of controlling hammer energy such that over-stressing of the pile is avoided. The calculation of non-axial stresses such as bending or eccentric stresses may also be involved in order to prevent pile damage.

Jan 1, 2010

By Abolfazl Eslami, Masoud Zare, Ali Asadi, Ali Abrang

"Physical small scale models for study of deep foundations can be performed in simple chambers (1g), calibration chambers (CC), and centrifuge apparatus (ng) which involve some limitations and difficulties. In recent years, Frustum confining vessels (FCV) have been developed for physical modeling of deep foundations. This device is frustum of a cone shape that applies a steady pressure on its bottom and creates a linear stress distribution along its vertical central line. A new FCV which has been built in AUT is introduced. This device has a height of 1200 mm, top and bottom diameters of 300 and 1300 mm, respectively. Through the application of bottom pressure up to 300 kPa, the insitu overburden stress conditions equivalent up to 40 m soil deposits consistent to the embedment depth of commonly used piles. Observation indicated that there is approximately a linear trend of stress distribution, and this device can create realistic overburden stress in the desired control volume along the central line. Moreover, a couple of compressive and tensile load tests were performed on steel tubular open end model piles driven in sand with length of 750 mm and different diameters and L/D ratio between 8-15. Comparison of load capacity between tested and full scale piles demonstrate a suitable conformity for similar confinement conditions. Therefore, the FCV can be realized as an appropriate apparatus for investigation of piling geotechnical behavior and examination of construction effects.IntroductionDeep foundations are designed as foundation system for supporting heavy loads, high rise and important structures. Different theoretical, numerical and experimental approaches have been developed to study the geotechnical behavior of deep foundations. Experimental methods are employed to clarify directly pile-soil interaction and because of repeatability, analogy, rapid measurement and cost efficiency, physical modeling can be realized as an intermediate technique compared to element testing and full scale load tests."

Jan 1, 2015

By Adam Pickles, Duncan Nicholson, Richard E. Prust, Hoe C. Yeow

"Moorhouse is founded on what at the time of construction were the deepest base grouted piles ever installed in London, specifically designed to accommodate settlement from the proposed development of Crossrail. This paper describes design and construction issues associated with this project with special emphasis on the construction aspects of installing these piles in a heavily congested site in Central London.INTRODUCTIONConstruction of the deepest base grouted bored piles in a congested site in Central London in 2002 posed a number of design and construction problems. To add to the complication, the new structure's footprint is within the safeguarded zone of the proposed new cross London rail link, Crossrail. Therefore the piles were required to be designed to allow for the effects of construction of the proposed Crossrail's tunnels and a new station at Moorgate. The design and construction issues associated with this project are described in this paper and methods used to address such issues are presented.MOORHOUSE DEVELOPMENTThe new nineteen storey high Moorhouse building was commissioned by Moor House Limited Partnership and will form another new Central London landmark building by the British architect Foster and Partners. Two of the four facades feature complex geometry to fulfill the city's planning requirements. The building is a steel frame structure stabilised by a reinforced concrete core. Floor plates span between the core and the perimeter with two rows of internal columns.The complex geometry of the superstructure requires a diagonal ""bandolier"" to transfer floor loads to certain perimeter columns. Another salient feature of the superstructure is the ribs that are provided to act as sloping columns to carry the loads down to the foundations."

Jan 1, 2005

By Frank Rausche

Introduction and Background Testing -Pile Preparation -Data Processing -Data Interpretation/Case Studies Case Studies - Existing Piles Stories from around the world

Jan 1, 2001

By Mohamed Elgouhary, Carol L. Tasillo, Daniel Koziol

"The Bolivar Dam, located near the Village of Bolivar, Ohio is one of a system of dams designed to provide flood control and water conservation in the Muskingum Watershed. The Bolivar Dam is a “dry dam” that only impounds water during flood events. In order to address problematic seepage, which negatively affects the structural stability of the dam, the U.S. Army Corps of Engineers (USACE) designed a partial-depth and partial-length Seepage Barrier Wall (SBW) through the upstream slope of the dam. For this project, TREVIICOS constructed a 36 in (914 mm) positive SBW by plastic concrete panel wall method and excavated using hydromill and clamshell equipment. The plastic concrete was manufactured on-site, which allowed for enhanced quality control and prompt service. This required the installation, commissioning and operation of a concrete batch plant on-site. This paper presents the challenging aspects of the design, manufacture and placement of the plastic concrete for the SBW in order to meet contract strength and permeability requirements as well as workability requirements necessary for tremie concrete placement.Project General InformationBolivar Dam is located in Northeast Ohio (Fig. 1). It is one of a system of sixteen dam projects designed to provide flood control and water conservation in the Muskingum Basin, which covers 20 percent of the State of Ohio (Fig. 2). Bolivar Dam is on Sandy Creek, a tributary of the Tuscarawas River.The Dam has been constructed, operated and maintained by the USACE, for the Muskingum Watershed Conservancy District. Its construction was completed in 1937 and it has been in operation for flood control since 1939.Bolivar Dam is a rolled earth fill dam, with a typical embankment section made of a central impervious core flanked upstream and downstream by a pervious outer shell with downstream rock toe. The embankment has a maximum height of 87 ft (26.5 m) and a crest length of 6,300 ft (1,920 m), and is comprised of the main embankment starting on the left abutment of about 1,500 ft (457 m) heading to the Northeast, followed by the terrace embankment of 4,800 ft (1,463 m) heading to the North. An upstream impervious blanket extends up to 500 ft (152 m) upstream of the dam along the majority of its length. The outlet works are to the left of the embankment, and consist of an intake structure with six gates, followed by two outlet conduits that finish in a stilling basin. To the left of the outlet works is the uncontrolled emergency spillway, which was doubled in width to 540 ft (165 m) in 1989, and excavated material utilized for construction of a stability berm against the upstream face of the main embankment. A concrete parapet wall was also installed along the upstream side of the crest during this work. In 1982, a toe drain, downstream filter berm and line of 35 relief wells were installed. The filter berm was recently extended an additional 200 ft (61.0 m) downstream and granular filters were placed over an approximate 2000 linear ft (610 m) reach of the lower terrace slope. (Fig. 3)."

Jan 1, 2016

By David A. Hart, Barry P. Osborn, Richard J. Totty, Ana T. Carvalho, Max B. Elliott

This paper addresses the experience designing and installing bored piles for the King’s Cross area. This includes continuous flight auger and rotary bored piles, with a range of diameters between 600 mm and 1200 mm, reaching a maximum depth of 56 m below ground level. Existing Network Rail Thameslink twin bored running tunnels are located directly beneath the subject plots. These tunnels have an external diameter of 6.6 m and the crowns of the tunnels are very shallow, in some cases just 10 m below the existing ground level. Some plots needed piles to be installed in close proximity to the tunnels, which required additional control measures and contingency plans. Pile verticality was monitored as the tip of each pile advanced and in-tunnel monitoring readings were verified and are presented. Lessons learned from designing, installing and testing the piles and monitoring the tunnels are addressed in this paper.

May 1, 2022

By Mario Mauro

Tuttle Creek Dam was constructed by the U.S. Army Corps of Engineers in the 1950?s on the Big Blue River in north-east Kansas. Since the dam is located in a seismic area, the safety of the dam was re-evaluated under the national U.S. Army Corps of Engineers Dam Safety and Assurance Program. After a series of studies and analyses performed by the Kansas City District of the U.S. Army Corps of Engineers, in 2003 the Department of the Army authorized the implementation of the plan ?Stabilize Foundation Soil without Drawdown Alternative?, during a 7-10 year construction period. As part of this plan, in 2006 Treviicos South carried out a large scale jet grouting and deep mixing test program downstream the dam. The test program included the installation of twenty-seven double and triple-fluid jet grout columns and twenty-seven jet-assisted deep mix columns. The jet grout columns were constructed at different levels of specific energy and cement content. The deep mix columns ranged in diameter between 3 ft and 6 ft. During column placement, the drilling and grouting parameters, pore pressures, and soil movements were instrumented in real-time. The downstream test area was enclosed by a cement-bentonite wall extended to bedrock, which allowed a 35-ft deep open excavation around the 45-ft deep columns. The exposed jet grout columns measured up to 15 ft in diameter, exceeding the anticipated target diameter. In addition to coring, some of the jet grout and soil mix test columns were saw-cut along the group axis, providing useful information on the internal column structure.

Jan 1, 2008

By Tai Luu, Maxim C. Schisler, Yaser Taheri

The Stevens Gateway Project is an expansion of the Stevens Institute campus overlooking the Hudson River in Hoboken, NJ. The plans call for 90,000 ft2 (8360 m2) of new classroom, research, and student life facilities in new, 4-story buildings. The excavations for the building footprints were bounded by city streets and existing buildings, including the historic Carnegie Laboratory of Engineering, built in 1902. Pit underpinning was originally specified for the Carnegie building. However, given the depth of cut, construction time required for the 13 ft (4.9 m) deep pits would be substantial. The geotechnical contractor retained for the support of excavation work therefore offered an innovative active soil nail wall design that would meet project requirements in a shorter timeframe. Unlike the passive soil nail systems common in the industry that are chiefly used for soil slope stabilization, active soil nail walls contain pre-stressed anchor components to resist soil movement and limit settlement of soil and structures being contained. In addition to a discussion of the overall design approach of the active soil nail wall system, this paper will include a detailed description of its constructability and effectiveness. This project’s use of a conventional slope stabilization technique for an unconventional purpose may have positive implications going forward. INTRODUCTION Stevens Institute of Technology is a private university in Hoboken, New Jersey that sits on the cliffs of the City of Hoboken overlooking the Hudson River and Manhattan Island to the east of the campus. In recent years, the university has executed numerous plans to expand and upgrade its campus academic, student life, and residential facilities. One such project is the Academic Gateway Complex. The plan adds 90,000 ft2 (8360 m2) of new classroom, research, and residential facilities while also enhancing community connections by building a park to serve as a green corridor for the city. The proposed construction took place on the north and south side of 6th Street between Hudson Street and River Street. The project included the demolition of an existing university building followed by the construction of two, 4-story buildings on the north and south property lots. The north and south buildings will be connected by a second floor bridge spanning 6th Street. The buildings each contain a full basement extending from the proposed ground floor at approximately El. 41ft (12.5 m) to the basement subgrade at El. 26 ft (7.9 m). Each building will be constructed on respective mat foundations. Figure 1 presents an overview of the project area.

Jan 1, 2019