Search Documents

By R. Marandi

The effective removal of heavy metals from aqueous wastes is among the most important issues for many industrialized countries, How ever biosorption, i.e. the uptake of heavy metals by non- living biomass, has gained increased credibility during recent years. Biosorption of Cr(VI) from aqueous solution, on pretreated and immobilized Aspergillus niger was investigated in a batch and countinuous reactors. A.niger biomass pretreated by boiling in 0.5 N NaOH solution for 15 min, exhibited higher Cr(VI) removal capacity than autoclaved biomass. The optimum adsorption pH value observed for Cr(VI) ions was 2. The Cr(VI)removal rate increased with a decrease in pH. The influence of contact time, pH, Cr(VI) concentration, biomass concentration and temperature on Cr(VI) removal were also evaluated. Biosorption of Cr(VI) on pretreated biomass followed the Freundlich and Langmuir adsorption models.In this study A.niger biomass was immobilized in Na-alginate matrix. The biomass beads packed in a column were able to remove metal ions.In this study we used two different flow rate in a column, 1.5 mL/min and 3 mL/min.The breakthrough data obtained for Cr(VI) was adequately by the Thomas and Yan models and the adsorption capacity of the biomass was found to less than the adsorption capacity obtaind in the batch study. When the beads containing biomass become saturated with metal ions, the adsorbed metals were eluted using 0.5 N NaOH solution. Therefor nearly 90% of Cr(VI) was desorbed by NaOH solution.

Jan 1, 2014

By B. Q. By

TiO2 is an ideal material for catalytic technology due to its unique properties. In this paper, Sm3+ doped TiO2 photo-catalyst was developed to improve the efficiency of TiO2 and to use the natural light as irradiation source, which was made from Titanium Tetrabutoxide and Samarium Oxide with the Sol-Gel process. The Sm3+-TiO2 photocatalyst was used to degrade reactive orange 4 (RO4) in Azo Dyes. The effects of solution pH, Sm3+ concentration and catalytic time on the degradation rate of RO4 were studied. The characteristics of the catalyst were analyzed with XRD and TEM. The experimental results show that the catalyst has high activity in the degradation of RO4. The Azo bonds of RO4 are active and easily broken by oxidation. The catalytic activity of the Sm3+ doped catalyst greatly depends on the pH of solution. The catalyst has high photo-catalytic activity at both neutral and alkaline conditions. The degradation mechanism of the Sm3+ doped TiO2 photo-catalyst was also discussed.

Jan 1, 2014

By B. Csoke

In a first stage of our investigations material properties of fly ash (three acidic and one alkaline type originating from combustion of various age coal) obtained from four various dumps have been characterized. In a next step systematic mechanical activation experiments??grinding??and measurements have been performed with various ashes to establish relations between grinding fineness (specific surface area), specific work input demand of grinding and activity. In a third phase utilization of a mixture of mechanically activated fly ash and lime for producing an independent binding composition has been assessed involving determination of interrelationship(s) between the degree of activation of fly ash, the lime concentration and the resultant strength of the obtained concrete. Finally, pilot size experiments were conducted and a test road section was built to explore possibilities for the production of suitable binding composition from the mixture of fly ash and lime as well as the applicability such mixture for road construction. After summarizing major achievements of the first and second stages of the work (history) the present study deals with the research conducted in stages three and four. Experimental results support the conclusion that the obtained binding material is suitable for construction of road bedding.

Jan 1, 2014

By Fang Liu, Xin Tan, Zhong-ming Wang, Yan-bo Shang, Jie Zhao

"The flotation separation of sulphides bulk concentrate containing Cu, Zn, Mo and Bi, which was obtained by both table-flotation of gross sand of gravity separation of wolframite and bulk flotation of wolframite slimes using butyl xanthate and oil No. 2, etc., has been conducted by using the cyanide process in the tungsten concentrator. The process has problems of high reagents consumption (25 tonne of cyanide dosage per year) and mineral processing cost (800~1000 RMB reagents cost per tonne of by-product concentrates), high mutual containing loss in the by-product concentrates and serious environmental pollution caused by lots of cyanide-containing wastewater. In order to solve this problem, a new cyanide-free separation technology is studied, which is used to process this sulphides bulk concentrate with 8.68% Cu, 8.98% Zn, 0.26% Mo, 1.58% Bi and 40.12% S. The results of the closed circuit test show that Cu, Zn, Mo and Bi can effectively be separated from this sulphide minerals concentrate by using the reasonable flotation-gravity flowsheet, high-efficiency collectors and regulators simultaneously. The metallurgical recovery and concentrate grade are as follows: molybdenum recovery is 94.63% with 50.62% Mo content; copper recovery is 85.18% with 29.29% Cu content; zinc recovery is 75.92% with 46.49% Zn content; total Bi recovery is 65.08% with 16.86% Bi content. The new technology is an alternative to the cyanide process due to its low cost for reagents, satisfying separation results and economic profits, and solves the problem of environmental pollution caused by the use of large quantities of cyanide. Some important parameters in separating the Cu-Zn-Mo-Bi sulphides concentrate are also introduced in this paper. This study provides pretty good technical support for separating the polymetallic sulphide ores containing Cu, Zn, Mo and Bi by cyanide-free technique."

Jan 1, 2014

By M. Rehor

The importance of brown coal as a raw material is currently given by growing energy needs of Czech Republic. More than 70% of mined brown coal comes from North Bohemian Basin these days. Mining of brown coal is run in four mining locations. They are geologically different and the parameters of mining coal are quite different too. This requires a little bit different methodology of both extraction and reclamation. Methods of reclamation works in the region are given mainly by the characteristics of overburden rocks appearing in the upper horizon of recuperated localities. The difficulties of the North Bohemian mine dumps reclamation works are caused by extremely unfavourable properties of rocks poured down to the majority of mine dumps. These are mainly rocks of the overlaying strata and the rocks strata of brown coal bed. Main materials poured down to the mine dumps are sands, clayey sands and kaolin ? illitic clays. Admixtures in filled rocks consist of organic (coal) mass, siderite and pyrite. These rocks are mechanically instable with respect to the wind and water erosion and during weathering they are getting unfavourable, acid (phytotoxic) nature, due to the influence of SO3 and Al ions. External and internal dumps of open pit mines are significant part of the North ? Bohemian landscape sustained by excavation. Their as fast as possible preparation and gradual integration into ecosystem of the area is interest of both citizens of region and mining companies. The paper briefly summarizes the methodology of restoration of the largest dumps of the North Bohemian Brown Coal Basin and the results of analyses and evaluation of samples taken on restored localities Rado-vesice dump, Strimice dump, Ru?odol dum pand internal dump of Bilina mine. An example of modern non-tradicional restoration methods is the restoration of internal dump of Bilina mine (application of power plant stabilizer). According to observations and results of sample analyses the methods of restoration were selected to limit the erosion influence, adjust the chemical and physical composition of surface of Radovesice and Strimice dumps. The application of marlites and bentonite prevent the unfavourable weathering processes on dump surface. Compensation of Quaternary sediments was artifically formed here. The need of marlite ploughing in, application of organical substrates and vegetation preparation was proved on Radovesice dump. The conception of landscape reclamation of the largest dumps after finishing of mining, methodology of technical reclamation and well considered using of fertilizable soils are main results presented in this article.

Jan 1, 2014

The effect of the acid anion on chalcopyrite (CuFeS2) leaching has been examined, under care-fully controlled conditions, in a range of acids in stirred reactors and columns at pH 1. Solution speciation calculations were performed to determine possible rate controlling species. The relative leach rates of Cu from chalcopyrite can be explained quantitatively entirely on the basis of solution speciation without the need to invoke any rational relating to surface structure/speciation. The rate of Cu release is first order with respect to Fe3+ activity. The stirred batch reactor experiments at fixed pH 1, Eh of 750 mV (SHE) and 75? showed that chalcopyrite leach rates were rapid in both HClO4 and H2SO4 with 100 % Cu recovery after 73h and 97 h respectively. However, the leach rate in H2SO4 was slower as compared to the HClO4 leach due to a slower increase in the activity of Fe3+ due to the formation of FeSO4-. The presence of Cl- in the leaches (HCl and H2SO4 with NaCl added) led to a low activity of Fe3+, due to the high activity of FeCl2+, resulting in very low leach rates. For the column leach experiments dissolution of Fe and Cu from the pH 1 HCl eluted chalcopy-rite column with quartz proceeded at several times the rate of any other column (chalcopyrite with and without quartz and/or pyrite leached with H2SO4, HClO4, HCl). Three observations indicate that galvanic interactions are not leach rate controlling role: a) The rate of leaching was not uniformly increased for the non-quartz containing columns where the two sulfide minerals, chalcopyrite and pyrite, are in physical contact as compared to the analogous quartz containing columns where they are not; b) there exists a reasonable correlation between the rate of Cu release and the effluent Fe3+ activity for all columns thus indicating that the leach rate is determined by solution speciation; and c) in all cases the proportion of Fe to Cu leached indicates preferential dissolution of Cu over Fe. However, the proportion of Fe to Cu is either the same or greater than expected on the basis of the single mineral columns. This indicates that chalcopyrite is not dissolving preferentially to pyrite.

Jan 1, 2014

By F. N. Shi

Ore breakage characterization plays an essential role in the design and optimization of comminution circuits. Recently, the JKMRC comminution research team has developed a Rotary Breakage Tester (JKRBT). The JKRBT uses a rotor-stator impacting system, in which particles gain a con-trolled kinetic energy and are impacted against the stator, causing particle breakage. The first unit of industrialised JKRBT was installed at the Anglo Research in South Africa in March 2007, and five more JKRBTs are currently being fabricated for some of the world?s major mining companies. In addition to the JKRBT, an improved breakage model has been developed at the JKMRC, which more accurately describes the effect of specific energy, particle size and incremental breakage caused by repetitive impacts. The validation outcomes show that the JKRBT, together with the new breakage model, generate statistically similar breakage parameters to the traditional drop weight tester (DWT), but with significant advantages over its predecessor. The limitations of the DWT, specifically its lack of precision of the energy input, the lengthy time required to run individual tests and the challenges en-countered in testing small particles, have all been overcome by the JKRBT. The recent developments in the JKRBT and the new breakage model offer several prospective applications. These developments have the potential to revolutionize the ore breakage characterization in the years to come.

Jan 1, 2014

By L. S. Zhou

HermesTM metal magnetic liner (MML) has been invented and manufactured by China Metallurgy and Mining General Co. (CMMC). This paper describes its mechanism, structure, magnetic field distribution, application, economic benefit and safety performance. The 10 years? service life in Benxi Steel?s Waitoushan Mine, along with 6 years? technological analysis on its application in 5500mm×8800mm (diameter × length) ball mill in Anshan Steel?s Diaojuntai mineral processing plant, has proved its advantages such as super reliability, long service life, light weight, thin thickness, low noise and short payback period. It has also demonstrated its positive effects on the grinding process such as high productivity, energy-effective performance and low consumption of grinding media. It reduces labour intensity and improves working conditions, due to its easy installation, free maintenance and the fact that it doesn?t require fastening bolts or cause slurry leakage. It is de-signed scientifically in accordance with the varieties of processing lines, mill specification, ore type and grinding media, and has been applied in different grinding processes for magnetite, hematite, gold ores, nonferrous ores and other materials. HermesTM MML has three types of products: General, Composite and Heavy-duty. They are designed to meet the requirements from customers in China and abroad. So far, more than 400 sets of MML have been applied in ball mills with diameter rang-ing from 1500mm to 5500mm. It has become highly popular in American market recently due to its safe and effective performance.

Jan 1, 2014

By F. Q. Cheng

Despite the successful industrial practice to recovery KCl by flotation, the adsorption state of collectors at KCl salt surfaces is still not fully understood. In this paper, the captive bubble contact angle measurements at KCl and NaCl crystal surfaces in their saturated solutions are reported. The influence of different collectors and their concentration are considered. The results show that both cationic and anionic collectors produce a hydrophobic state at the structure breaking KCl salt sur-face, with finite contact angle values of between 30o and 40o. In contrast, the contact angle at the structure making NaCl salt surface is zero at all collector concentrations, suggesting that no collec-tor adsorption occurs, a supposition that is supported by results from molecular dynamics simulation (MDS). Further, it appears that the presence of surface defects such as edges and corners promote the adsorption of collectors at the KCl surface, and that the flotation is achieved by bubble attachment at the edges/corners of KCl particles with the formation of aeroflocs.

Jan 1, 2014

By M. Kinnunen

Handling of municipal solid waste (MSW) and control of its potential resources is becoming increasingly important in modern society. The OECD (Organization for Economic Co-operation and Development) average on municipal waste produced in 2003 was that of around 570 kg per inhabitant. In European Union countries around half amount is of MSW landfilled. In Finland still 88% of MSW was landfilled in 2004. Since incineration reduces MSW volume significantly while producing heat energy, it has become one of the most common waste handling techniques. The shortcoming of incineration is however, that incinerated MSW is often not pre-sorted and it produces slags and ashes as side streams from which recovery of metals is difficult. This paper looks into possibilities of scrap metal recovery for recycling from municipal solid waste incineration (MSWI) bottom ash. In order to do that, a flow sheet of physical separation methods was developed and tested with Finnish rotary furnace MSWI bottom ash. In addition, an empirical model for estimation of the recoveries of scrap metals with physical separation methods for treatment of MSWI bottom ash was developed. According to the results of this study, for 1 Mt of incinerated MSW with 30% mass reduction, a minimum resource potential of 100 kt for magnetic metal scrap of roughly 24 % grade and about 19 kt of non-magnetic metal scrap of roughly 65 % grade. In other words, 57 kg magnetic scrap and 12 kg non-magnetic scrap per inhabitant at the mentioned grades, respectively. Although wide variations of parameters affect the MSWI bottom ash quality, it can be said that a considerable amount of metals is drained into MSWI bottom ash. Results of this study show that from MSWI bottom ash significant material streams metal scrap can be reintroduced into the resource cycle which would otherwise be lost.

Jan 1, 2014

By S. H. Morar

Froth flotation is a physico-chemical separation process that takes place in two phases; pulp and froth phase. It is widely recognised as a complex process, due to the range of interactions present within the system. Of critical importance is the role of the froth phase within the system. The pulp kinetics governs the maximum potential recovery within a flotation cell, while the froth phase governs the selectivity via the froth?s stability. Higher froth stability improves recovery at the expense of grade, and lower froth stability improves selectivity. It is well known that the two major factors affecting froth stability are attached particles and solution chemistry. This paper looks at a flotation bank at different froth depth and frother concentrations. The air recovery to the concentrate is determined at each condition and relates the effect of the operating conditions on froth stability and transport to the amount of solids that are recovered to the froth and concentrate by true flotation. The results presented show that, for a given process objective, which in this case was a consistent mass pull profile, depending on the operating conditions, solids recovery in the pulp is affected by the air rate required to maintain the target mass pull. To a smaller extent, the changes in the pulp composition affect down-stream pulp recovery. The variation in solids recovered into the froth drives the froth stability at the start of the flotation bank, while the frother drives the froth stability at the end of the bank. The performance in between these two extreme conditions arises from an interaction of these two effects. The consequences of these interactions can give rise to counter-intuitive responses that can confound efforts to optimise the performance of the bank.

Jan 1, 2014

By S. Banisi, A. R. Hasankhoei, A. R. Ghasemi, E. Razi, G. A. Parsapour

At the pelletizing plant of the Gol-E-Gohar mining and industrial company two parallel dry closed grinding circuits, each with the average throughput of 300 t/h, are used. Each grinding circuit consists of a burner, a dry ball mill (6.2 m×13 m) and an air separator. The ball mill consists of a 2 m-long drying and an 11 m-long grinding chambers. The iron ore concentrate is fed to the drying chamber by a feed chute. The first 1.35 m of the drying chamber consists of 56 flights in two rows to decrease the feed moisture from 5% to below 0.2% and the rest of dryer chamber consists of deflectors to pass the material to the grinding chamber. It was found that when the feed moisture content increased from 1.3% to 3.5%, the throughput decreased by 12% (35 t/h) indicating a low performance of the dryer. Monitoring the wear rate of flights for a period of 12 months showed that the first 0.8 m length of the flights length did not experience any wear. This means that about 59% of flights do not contribute in material distribution and drying. A DEM simulation of feed chute and the drying chamber demonstrated that due to the inappropriate design of feed chute most of materials do not get in touch with the first 0.8 m length of the drying chamber. To overcome this problem, various feed chute designs with different geometries were simulated by the KMPCDEM© software. With the aim of arriving at a proper material trajectory, where the total length of the flights are used, a new feed chute was selected. The simulation results indicated that if the height of the flights is increased from 1.60 to 2.26 m and the slope is increased from 45 to 48 degrees the material arrive at the first 0.48 m of drying chamber. In this manner, the unused part of the drying chamber decreases from 59% to 36% of the length. After installation of the new feed chute, during a period of three months the throughput increased by 36 t/h.

Jan 1, 2018

By J. H. Zhang

An atomic force microscope has been used to measure the forces acting between two silica and two rutile surfaces in the presence and absence of cationic surfactants, CnTACl (n = 12~18). The forces measured in the absence of surfactant can be fitted to the DLVO theory. At short separations, however, the silica surfaces exhibited repulsive hydration forces, while the rutile surfaces did not. On the other hand, the forces measured in the presence of the cationic surfactants show long-range attractions that are larger than the van der Waals forces. The long range attractions are the strongest at of the point of charge neutralization (p.c.n.), which decreases with increasing surfactant chain length. The possible origin of the long-range attraction has been tested in view of the charged-patch model of Miklavic et al. (1994). However, the sizes of the patches back-calculated from the model were much larger than those the patches (or hemi-micelles) determined experimentally and reported in the literature. It is, therefore, suggested that the long-range attractions observed in the present work are due to the structural response of the water molecules in the vicinity of hydrophobic surfaces.

Jan 1, 2014

By P. Pourghahramani

Several structural characteristics change during intensive milling such as chemical composition, phase transformation, crystallite size, lattice strain, lattice parameter (s) and solid reactivity etc. The creation of defects enhances the stored energy (enthalpy) in the solids and consequently causes a decrease of activation barrier for the process and/or subsequent processes. In this paper, the effects of milling on the structural changes of hematite have been investigated using dry millings. The structural changes have been characterized using a combination analysis of BET surface area measurements and X-ray diffraction (XRD) analysis. Besides, the hydrogen reduction behaviors and kinetics of mechanically activated samples and initial sample were studied using simultaneous thermal analysis (STA). The methods of Williamson-Hall and Warren-Averbach were used for analyzing of XRD patterns to resolve and extract the microstructural characteristics of hematite phases. It was concluded that the breakage and aggregation of particles take place mainly in the starting and prolonged stages of dry grinding, respectively. The BET surface area enlarged steadily over the grinding processes whatever milling methods were utilized. The characterization of structural changes revealed that the hematite milled under various conditions did not undergo any significant reaction or phase transformation during milling processes. In addition, X-ray amorphous phase con-tent increased gradually with extending the grinding intensity. The maximum X-ray amorphous phase exceeds about 81% after 9 hours of milling in both tumbling mill and vibratory mill. The Williamson-Hall plots revealed the anisotropic character of line broadening for deformed hematite and changes in the trend of microstructural characteristics as a function of milling time. It was found that the surface weighted crystallite size decreases and lattice strain increases over the grinding periods. The minimum surface weighted crystallites were calculated about 17.3 nm, 12.2 nm for the products of tumbling and vibratory mills respectively. The maximum lattice strain,, in the grinding with tumbling and vibratory mills was calculated about 4.44×10-3 and 3.95×10-3respectively. 21/210nmLe=<> The non-isothermal kinetic analysis of the products revealed that Fe 2O3 reduced to Fe in a two-step process via Fe3O4. Intensive grinding resulted in improved resolution of overlapping reduction events. It was also established that the mechanical activation had a positive effect on the first step of reduction. The prereduction step in the activated samples initiated and completed at lower temperatures than that in non-activated samples. The activation energy of reduction decreased at the first step of reaction with increasing the grinding intensity. Intensive milling increased slightly the average activation energy of the second step of reduction due to the present of finely agglomerated particles and intensive sintering of the particles in higher temperature ranges.

Jan 1, 2014

By M. Kargar Razi

According to the unique properties and many applications of nano silver powder, it was prepared from acid leaching tail solution. The low value residual gold and silver ions were occurred with fellow heavy metals as pollutants (Fe2+, Cu 2+and Zn2+) in acid leaching tail solution in Mouteh gold mine in Iran. Preparation of nano silver particles was achieved in two steps: first, by addition of ammonia as separation step and second by using different reagents as precipitation and extraction steps. Different controlled parameters were including pH, residence time and temperature, mixing time, and reducing reagents to metals molar ratio. Acid leaching process was carried out with sulphuric and nitric acid via suitable reductants. In order to remove copper, zinc, and silver ions from solution, all of the conditions were controlled. The optimum conditions for preparation of nano silver powder with less than 90 nm were pH 10.5, hydrazine/methanol to silver molar ratio of 3 to 4, and reduction time of 5 min in 45 °C. The results were evaluated via SEM, A.A and UV- Vis spectroscopy analytical methods.

Jan 1, 2014

By F. H. Wang

The Yinmao Lead-Zinc Mine Co. Ltd. has got 50 years of mining history. In recent years, the manganese grade in the flotation tailings has been continuously increasing. In order to make fuller use of the existing resources, as well as to increase the company?s economic efficiency, our company adopted the technique ?magnetic separation? and ?iron removal? to effectively recycle the manganese concentrate resources.

Jan 1, 2014

By C. Carrasco

"Over the last 30 years the average grade of mined ore bodies has significantly decreased while the proportion of waste removal has in many cases more than doubled. This has been identified as prime reason of a major increase in energy consumption and decrease in productivity across mining operation. Metal coarse preconcentration of ROM feed grades by size rejects low grade gangue/waste material in the size range of 10-100 mm prior to grinding, typically before primary crushing. This relies on propensity of metal to preferentially deport in the fine size fractions after breakage. Metal preconcentration by size has the potential to increase energy efficiency and therefore improve mining productivity on unit of metal basis. Results of an extensive belt cut sampling campaign conducted at a major Australian Au-Cu mine operation show that for some samples between 90% of Au and 80% of Cu is in 40% of the mass at -50 mm fraction. This indicates that low grade coarse material can be removed from the circuit, doubling feed grade at half of the tonnage and therefore improve energy efficiency per unit metal produced. This response, however presents significant variability in the same order as other processing attributes such as impact hardness and flotation recovery. This has led to development of geometallurgical laboratory tests using blast hole chips and drill core facilitating mapping and population of coarse metal preconcentration signatures in long term resources and short term production models. Preferential Cu deportment by size at drilling scale can be recognised, however scales up factors are required to transform laboratory results to production responses. At 50 % of mass the drilling products underestimate the belt cut responses by 20-30 %. Bulk sampling campaign with blast hole and drill core samples spatially related was also conducted to investigate in more detail the difference between production scale and drilling scale preconcentration responses."

Jan 1, 2014

By L. G. Wang

The stability of foams and froth plays an important role in flotation, in which small amounts of relatively weak non-ionic surfactants (frothers) are used to produce air bubbles and foams. In the present work, factors affecting the stability of the foams produced in the presence of common frothers, such as n-pentanol, n-octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG), have been studied. We used the thin film pressure balance (TFPB) technique of Schelud-ko-Exerowa type to measure the equilibrium film thicknesses. The results were used to determine the contributions from the various surface forces to the disjoining pressures in the thin lamellae (foam) films formed between air bubbles. In addition, we used a model developed by Wang and Yoon (Colloids and Surfaces A: Physicochem. Eng. Aspects, 2006) to calculate the elasticities of the lamellae films at the critical thicknesses at which films rupture. The surface forces and elasticity da-ta were then compared with the foam stabilities in the presence of the various flotation frothers. It was found that foam stabilities are controlled by both film elasticity and surface forces, the relative contributions of which change with frother type and concentration. In general, surface forces play a more important role at relatively low frother concentrations, while elasticity plays a more important role at higher concentrations. At the frother additions usually employed in the mining industry, MIBC relies on surface forces while PPG-400 relies on film elasticity in producing stable foams. The former is capable of dampening the hydrophobic force, which is a major attractive force destabilizing lamellae films, while the latter is capable of reducing surface tensions at low concentrations.

Jan 1, 2014

By L. E. Veki, S. M. Luukkanen, J. P. Karvonen, J. O. Leppinen

Today there is a consensus that xanthate adsorption on sulfide minerals is primarily controlled by redox reactions occurring at specific potentials on these semi-conductive minerals. Consequently, it is possible to control xanthate adsorption by controlling electrochemical conditions in the system by using oxidizing and reducing agents. The scope of this study was to investigate the possibilities to increase the selectivity of Cu-Fe-Zn ore flotation by applying electrochemical control in the conditioning of the flotation feed. In this work, mild steel grinding in a nitrogen atmosphere was used as the basis to provide a negative starting potential and minimize the amount of oxidation products on sulfide mineral surfaces. To study how different potential levels affect flotation results, a controlled conditioning procedure was utilized maintaining potential at a desired level by titrating the pulp with air. Xanthate adsorption kinetics during conditioning was examined by taking pulp samples for spectrophotometric analysis and laboratory flotation tests were conducted for samples that underwent the controlled conditioning procedure in the potential range of -200mV to +200mV vs. SHE. A clear correlation was detected between chalcopyrite recovery and the potential during controlled conditioning indicating that there was a constant increase in chalcopyrite recovery when the potential was shifted to more anodic values. It is possible that utilizing potential control in the conditioning stage, a smelter grade copper concentrate can be achieved directly in rougher flotation without cleaning stages. Conditioning in favorable conditions had significant positive effects on flotation selectivity of chalcopyrite. The improvement in copper concentrate grade being predominantly caused by the depression of pyrite. By applying the controlled conditioning procedure pyrite recovery in rougher flotation was reduced even low as under 1%, while in the tests without controlled conditioning, pyrite recovery varied between 7.5 – 65.7%. The result of this work indicate that affecting collector adsorption by electrochemical control in the conditioning stage can provide significant improvement in sulfide mineral flotation and industrial applications could lead to decreased chemical consumption, reduced equipment and maintenance costs.

Jan 1, 2018

As a kind of collector, Xanthates are generally used to make sulfide minerals hydrophobic in flotation process. Xanthate adsorption on a galena surface has been widely studied experimentally. In this paper, DFT methods were employed to investigate the local adsorption interactions about the collectors,such as ethyl xanthate (CH3CH2OCS2?, EO) and ethyl trithiocarbonate (CH3CH2SCS2?, ES), absorbing on two different PbS clusters. From the results, it can be easily found that, on the edge or at the apex, both collectors, with two S atoms bidentate coordinating on the clusters, have surprising interaction energies, while on the surface, its interaction is relatively weak in the form of monodentate ligand. NBO analysis results reveal that there is at least a covalence bond with sulfur atom about 10% and lead atom about 90% when the absorbed lead is on the lattice edge or at apex, but, if the absorbed lead is on the lattice surface, no covalence band would be found. Meanwhile, the S-Pb bond, formed by the absorbed Xanthate and galena lattice, seems to have much more covalence characteristic than that formed in the PbS lattice inner. Furthermore, those data also imply that the difference of the collecting effect between the EO and the ES may be not notable, because of the similar distance and the interaction energy for the same interaction mode.

Jan 1, 2014