Search Documents

By T. C. Alex, S Srikanth, Premchand

It has been suggested that reduction of the iron and manganese phases as far as FeO and MnO is preferred for the complete liberation and selective reduction of the copper, nickel and cobalt oxides in manganese nodules. The oxygen partial pressure/temperature regime suitable for this purpose has been delineated. Free-energy minimisation and thermogravimetric results indicate that the requisite conditions can be achieved if more than 10% of neutral oil is used at temperatures greater than 923 degrees C. Neutral oil content, temperature and roasting time have been optimised to maximise leaching recoveries of Cu, Ni and Co: up to 96% of Cu and Ni and up to 85% of Co can be recovered if 15% of neutral oil is used as a reductant at 973 K for 90 min

Jun 21, 1905

By A. G. Pasamehmetoglu, N. Bolukbasi, O. Koncagul

A study has been undertaken to establish the relationships between the O&K wedge test cutting resistances and the geotechnical parameters of rock materials in the context of bucket-wheel excavator operation. Prediction equations were formed to estimate the cutting resistance from the geotechnical parameters by multiple regression analysis. The cone indentor index, uniaxial compressive strength and Shore hardness parameters have been found to be the most significant predictors

Sep 1, 1991

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

Whether the microscopic bubbles generated by the high energy dissipation and high feed-slurry velocities in new flotation cells are stable in solution and what roles they play in particle collection are of great interest for the flotation of fines. Experimental work has shown that, with fast flow of liquid through an orifice, stable microscopic bubbles can form in flotation systems by hydrodynamic cavitation in the absence of gas supersaturation. The minimum flow rate at which bubble formation is initiated varies from 8 to 15 m/s, depending on the design of the cavitation tube, which is within the range of feed slurry velocities of some newly developed cells. Feed aeration enhances the formation of micro-bubbles by hydrodynamic cavitation. The study suggests that the fast flotation kinetics of some new cells may be attributed in some degree to the formation of microscopic bubbles

Jun 21, 1905

By D. C. Kaliampakos, A. K. Moutsatsou, J. K. Skotaras

The wastes from marble extraction in the Thasos- Kavalla-Drama region of northeastern Greece could be utilised as a new source of high-quality white carbonate fillers for the European market. Large deposits, satisfactory properties, acceptable processing costs and environmental benefits are among the factors that would have a positive bearing on a proposal for their use in this way. DTH, the waste arising from dolomitic marble quarrying operations on the island of Thasos, appears to be the more suitable material than DA waste from Nikissiani on the mainland because of the lower cost of primary grinding and the higher production rate of ultrafines with a mean particle size of 5 micrometres (the optimum size for filler properties in the case of both DTH and DA), its superior whiteness, the benefits that such use would bring to a very severe and complex environmental problem and the lower transport cost

Jun 18, 1905

By H. K. Taylor, B. Denby, L. D. Smith

Contributions by H.K. Taylor and G.A. Davis discuss the three papers published in Transactions IMM A, vols. 103 and 104, with responses by Smith and Dowd

Dec 1, 1995

By R. Ciccu, P. P. Manca, A. Bortolussi, G. Massacci

Tool performance and the unit cost of cutting depend on a number of operational variables (peripheral velocity, pull-back force, water injection rate, angles of the sections of wire outside the rock) as well as on the geometric features of the cut itself (area and shape). Cutting rate and wire productivity are also influenced by the type and number of diamond beads per unit length of wire and by the characteristics of the rock (granite or marble). A computer program aimed at handling a problem of this complexity has been developed and tested with the use of available field and laboratory data and has been found acceptably reliable. Discrepancies between current industrial data and some of the results suggest future lines of research, while the simulation should also be extended to include different types of rock and tool and a variety of bench face geometries

Aug 1, 1994

By D. W. Taylor, I. W. Farmer, N. Mojtabai

Rittinger's and Bond's descriptions of rock crushing relate the energy input required to fracture rock and the surface energy required to form new fractures to the change in specific surface area of feed and product during comminution. The potential applicability of this approach to blasting is illustrated, using the results of data from bench blasting tests on Pinal schists and production blasting of Carboniferous limestones. The approach contributes to understanding of the mechanisms involved in blasting and to the design of test blasts. A modified form is presented of the relationship between blasting energy, specific surface area of the muckpile and a rock energy constant related to the discontinuity structure of the rock. The modified equation fits observed data and offers a simple basis for further experiments

Jun 19, 1905

By P. J. Baguley

The model has been developed on the basis of the observation that the partitioning behaviour of a particle is related to its calculated terminal velocity. It utilises a theoretical calculation of the terminal velocity of each particle class. This is then correlated with the observed partition data for a plant separator using empirically-derived functions of operating conditions which take into account effects such as bath turbulence, holes in drum lifters and feed arrangements. The model successfully decouples the effects of medium density and viscosity and is appropriate for any bath-type separator. The correlation between calculated terminal velocity and actual partitioning behaviour was established and modelled using data obtained from two Wemco drums treating Fe and Mn ores. The model can be used to predict the prevailing size-by-size partition curves and the separation (product grades/recoveries) given the washability of the feed and operating conditions. Simulations are used to show that, for the treatment of Fe ore, there is a maximum medium density beyond which product grades fall and that this maximum decreases as the proportion of magnetite in the medium increases. This is attributed to the dominant effect of viscosity at higher medium solids concentrations

Jun 18, 1905

By G. Zhan, P. Mousset-Jones, G. Danko, J. J. K. Daemen, C. Mezei

Paper presented at the conference Risk assessment in the extractive industries, held in Exeter, 23-24 March 1994, and first published London: IMM, 1994, preprint volume. 18pp., 12 refs. (Originally entitled: Tunnel roof diagnosis using a robotic sensor test bed.) An integral roof diagnosis method is proposed to assist in assessment of risk regarding the stability of an excavation. A Robotic Sensor Test Bed (RSTB) is being developed for the characterisation of roof stability. The sensor test bed consists of a sonic/ultrasonic wave response sensor, a laser surface profiler and a surface temperature sensor. These sensors are mounted on an articulated robot manipulator for performing remote-controlled or fully automated diagnoses. A number of laboratory and field sonic/ultrasonic tests were conducted. A high-energy ultrasonic transducer and an impact device were used to resonate rock slabs. The fracture depths of the slabs were found to be inversely related to the measured resonance frequencies. The agreement between identified and actual dimensions was acceptable. Field tests also showed that loose rock on the surface can be clearly distinguished from solid formation by comparing their wave responses. The robotic laser profiler part of the RSTB was used to measure surface geometry. Different scanning methods are being developed to achieve the fastest and most precise measurements and to provide pertinent information about rock joints and major fractures

Dec 1, 1994

By B. Tiryaki, O. Z. Hekimoglu

Shearer drums are a critical component in the overall performance of coal shearers, with the cutting performance depending very much on the disposition of cutter tools on the drums (the tool-lacing arrangement). A series of practical and theoretical studies has been undertaken to investigate aspects of shearer drum vibration in terms of circumferential pick spacing. A number of commercially available drums were redesigned and the lacing patterns compared with those of the original drums under near-uniform conditions. Mine trials were carried out at the Middle Anatolian lignite mine in Turkey with drums fitted on Eickhoff type EDW-230 double-ranging drum shearers. It was found that the performance of drums could be improved if the concept of circumferential pick spacing was taken into account in CAD packages along with the existing design parameters such as cutting rate, reduced dust, low pick consumption and low down-time

Jun 19, 1905

By P. Mousset-Jones, G. Danko

Variations of the temperature and steam/moisture content of the air with distance and time are modelled for a single airway. The input for the simulation is an air temperature that varies with time, together with the moisture/steam content that results, for example, from a fire with a given distribution of heat and of fume concentrations at the beginning of the airway. The transport of heat and moisture to the surface of the wallrock is assumed to be simultaneous. Such multiphase convection may result in evaporation from the moist wall close to the fire and recondensation downstream. The modelling of this non-linear effect is a unique feature of the new simulation. A new analytical solution is used to calculate the conduction of transient heat within the rock mantle, which, in the event of a fire, is typically a short-term process. This allows for an arbitrary variation of surface temperature with time - unlike that permitted by the age function solution, which is limited to stepped temperature changes. An iterative numerical scheme that has recently been developed to simulate mine climate is used to calculate the coupled transient heat conduction and multiphase surface heat transport in successive length increments along the airway. To demonstrate the simulation procedure a numerical example is presented in which a fire with a given distribution of heat and fume concentrations with time is located at the beginning of an airway

May 1, 1991

By S. Babendererde

The twenty-ninth Sir Julius Wernher memorial lecture of the IMM, presented at Tunnelling '97, London, 2-4 September 1997. The tunnelling industry is well prepared to face the challenge from the population explosion in urban areas in the near future. Many well-established yet redundant concepts are still impeding progress, however, including the prediction of excessive surface ground settlements. The correct selection of TBM can minimise these, and ground deformations can be avoided completely if the appropriate techniques are applied. Advanced techniques have been used in the Tokyo Bay Crossing, where the tunnel lining was installed by robots. Other advanced techniques include the use of a sliding slip form to give temporary support to an extruded tunnel lining, the chemical processing of ground by polymers during earth-pressure balanced tunnelling and the use of electronic monitoring and steering devices in TBMs. There will be challenges to tunnelling in urban environments, as open cut techniques will no longer be tolerated. Two examples of mined stations are briefly discussed

Jun 19, 1905

By T. Yalcin

In the Box-Wilson method, the correlation between dependent and independent variables is represented by a polynomial response function, whose constant and coefficients are determined by applying regression analysis to the experimental data collected. The five levels used for each variable consist of a minimum, a maximum and three intermediate values. A study was carried out using Ni-Cu ore from Sudbury, Ontario, in which 15 experiments designed according to the Box-Wilson method were carried out in random order and in duplicate. The two sets of replicate data showed close similarity, with an overall variance of 0.311 for the five parameters studied. The response functions were used to optimise frother dosage, collector concentration and air flow rate and an experiment was then carried out under the optimised conditions; the results agreed closely with those predicted by the response functions

Jun 21, 1905

Two concentrates from Palabora, in South Africa, containing 0.056-0.068% undesirable Cu and 0.8 or 2.2% Ti, were chlorinated with air:chlorine ratios of 10:1, 15:1 and 20:1 at temperatures between 1 200 and 1 329 K. The resulting volatile chlorides were condensed and the solutions analysed for Cu, Fe and Ti. Recovery of Cu was less than 25% at low temperatures and short reaction times, but at 1 258 K almost all Cu was removed from the magnetite at all ratios of chlorine to air. At higher temperatures, the increased carrying over of iron as FeCl3 could be minimised by decreasing the partial pressure of chlorine. No titanium was detected in the volatile products and the percentage of Cu recovered was independent of Ti concentration in the concentrates, though as a function of Cl2 vol%, more Cu was recovered at 1 200 K from the low-Ti than from the high-Ti concentrate. In a fluidised-bed reactor, Cu recovery was 58-90% and iron carry-over less than 10 ppm

Jun 21, 1905

By P. E. J. Pitfield, S. D. G. Campbell

The regional shear zone runs along or near the southern margin of the Chinhoyi greenstone belt. It hosts four of the seven mines in the southern part of the belt with recorded production above 100 kg Au, including the top two current producers. Displacement occurred in the late Archaean, producing a shear zone with a trend ranging from northeast at Golden Kopje to east at Muriel. The orebodies at the two mines formed synchronously with the shearing and show strong but contrasting structural controls on mineralisation. The Golden Kopje orebodies plunge to the southwest, parallel to the intersection of curved foliation with discrete shear planes and sub-perpendicular to local stretching lineations. The Muriel orebodies plunge steeply west but parallel to local stretching lineations. The greatest fluid flow during mineralisation of the shear zone was along either the intersection of fabrics (Golden Kopje) or the extension direction (Muriel). There is no unique relation between the orebodies and the extension or shear direction. Where earlier mining has not established the directions of the oreshoots it is essential to understand the possible structurally controlled geometries of orebodies before planning a drilling programme to evaluate their potential

Apr 1, 1996

By L. J. Cabri, J. M. D. Wilson, R Lastra

An image analysis program can search for gold minerals in polished sections by scanning about 100 x 100 back-scattered electron images at a magnification of x400, allowing gold grains as small as 1 micrometre in diameter to be detected. Typically, a c.15 h overnight search of a product smaller than 45 micrometres will scan c.1 500 000 particles, providing data that are not easily obtained through manual operation of an optical microscope. The program locates grains of the correct brightness, acquires gold X-rays from them by wavelength-dispersive spectrometry, filters the data to remove artefacts and record the images and stage locations for subsequent retrieval. At the end of the run, the program allows the operator to verify and identify the grains found. Industrial studies at Canmet have included determining the nature of gold in cyanidation tailings, checking the mineralogy and size of gold grains in samples from an Indonesian Cu-Au concentrator and locating and measuring gold liberation and grain sizes in an ore

Jun 21, 1905

By R. Lahtinen, M. Tiainen, R. Salminen

The application of similarity analysis derived from regional geochemical mapping data to the location of Ni-bearing intrusions was tested in southwest Finland, where a well-known nickel belt is situated. Samples of till from the vicinity of the Vammala and Kylmakoski Ni-Cu deposits, which were collected independently of the Geological Survey of Finland's regional geochemical mapping programme, were used to provide geochemical modelling data. The data consist of the aqua regia-leachable concentrations of 20 elements from the less than 0.06-mm fraction of glacial till. The variables used in the similarity analysis were selected on the basis of a factor analysis in which the method of oblique rotation was used. A hierarchical clustering of the modelling samples produced two main groups. The first group was described as the "nickel deposit environment model" and the second as the "nickel deposit location model". The data for the standardised variables were compared sample by sample with the model data by similarity analysis using the Simana program with a cos theta measure of pattern similarity. The nickel deposit environment model delineated the known Ni belt and indicated an extension to the east. The nickel deposit location model identified target areas of reasonable size with the greatest potential for Ni ores within the nickel belt

Dec 1, 1991

By P. A. Davies

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 11pp., 15 refs. Hazards such as vibration, dust emission and fragment projection can result in an area called the Danger Zone being set around a blasting site. Traditionally Danger Zones have been set solely on the basis of consequences (e.g. based on the maximum distance of rock projection or expected ground vibration plus a defined safety margin). Advances in risk assessment and its growing acceptance as a safety management tool have led to the setting of Danger Zones based on both consequences and frequency of occurrence. This allows distances to be optimised on the basis of acceptable risk levels rather than the potential consequences of infrequent events. The setting of a flyrock Danger Zone is used to demonstrate a risk-based approach compared with a traditional consequence approach

Aug 1, 1995

By T. Serradj

A study has been carried out to: develop a method for routine characterisation of rock strength and drillability through the particle-size distribution of crushed or drilled rock products, defined by the Protodyakonov index; establish correlations between the Protodyakonov index, uniformity coefficient and the constant grading equations; and propose an alternative rock characterisation index to classify rock strength and drillability for the northeast region of Algeria

Dec 1, 1996

By B. M. England, M. V. Swain, N. Bristow, R. D. Dukino

The toughness and fracture mechanisms of ores with significantly different microstructures from Yandi, Koolan and Mount Whaleback were studied with a view to understanding their degradation behaviour. Bulk fracture toughness was determined by the 3-point single-edge notch beam test and the results interpreted using Weibull statistical analysis; indentation fracture mechanics was also used to measure fracture toughness of the different mineral forms and to understand their response to contact fracture

Apr 1, 1995