Search Documents

By H. L. Willett

Wrapping up the symposium, covers incidence of spontaneous combustion in British mines, assessment of liability to spontaneous combustion, precautions, rate of advance, starting a line of a coalface, local heatings at roadsides, burying packs, coal headings, retreating longwall, detection and sealant coatings.

May 23, 1905

By G. D. Nicholls

There have been very few attempts to isolate the various factors that contribute to the overall imprecision of geochemical analytical procedures, due in part to the difficulty of distinguishing between them. The technique of spark source mass spectrography permits a ready distinction between the contributions to overall precision from sampling error and instrumental and other errors. With conventional methods of sample preparation for this technique sampling difficulties are responsible for 80-90 per cent of the overall imprecision. Examination of the probable location of the major difficulties in sample preparation indicates that the preliminary stage of grinding, mixing and extraction of a first aliquot (about 1/100 of the original sample) is generally perfectly adequate. The difficulty lies in the subsequent stages of sample preparation. Dry mixing techniques are unlikely to give good precision if the sub-samples actually examined by the analytical technique are less than 10 mg in amount. Solution techniques are less prone to sampling difficulty. Fusion techniques, unless conducted with great care, can produce more difficulty than dry mixing. Sample preparation is critical to the success of many analytical procedures. Selection of appropriate sample preparation techniques requires just as much care as the selection of techniques for the actual analysis.

Dec 1, 1971

By B. Sonmez, B. Aksanl, S. Ersaym, I. F. Erkal, S. L. Ergun

The comminution circuit at the plant has experienced severe problems arising from a feed containing much larger amounts of clay and having a higher moisture content than expected. Three solutions were proposed: replacement of the crushing circuit by tooth roll-type crushers; using washing drums; and introducing primary autogenous/semi-autogenous millling instead of crushing. Computer simulations studied the effects of the first two solutions on the circuit capacity. Laboratory and industrial scale ball mill batch grinding tests were carried out. The parameters of a kinetic model were determined. The ball mill circuit was sampled and operating model parameters were calculated. The ability of batch grinding parameters to represent the operating conditions was studied. Tests failed to find acceptable model parameters, but parameters from an industrial size batch mill were found to be suitable for simulation studies. The simulations indicated that a continuous feed of -12 mm provided by tooth roll crushers would maintain the desired capacity. Increasing the feed size to -25 mm would reduce the capacity by 8-15%. The use of washing drums could also solve the capacity problem, but small fluctuations in water flow rates might result in problems of excess water in the grinding circuit.

Jan 4, 1993

By R. F. Bell, Schultz

The paper briefly discusses the nature of spontaneous heating in mines in the Doncaster area, in the period immediately before 1967 and steps taken to prevent and treat such outbreaks. The changes that led to the increased rates of advice of Barnsley Seam faces since 1967 are listed and the effects of these increased rates on the frequency and location of spontaneous combustion are discussed. The change in methods of control required by the increased rate of advance of the faces and the changes in location of outbreaks are described. Some typical heating situations are evaluated. The methods described include the use of air sealants, water gels for filling of voids in wastes, the balancing of pressures across heating areas by pressure chambers, booster fans, and the resiting of air separation doors, and the sealing of air-ways by flooding. The authors discuss the influence of mine layouts on the risks of spontaneous combustion and advocate that future plans should be designed to limit the number of districts at risk when heatings occur.

May 23, 1905

By G. G. Lambert

The paper traces the pattern of spontaneous combustion in the workings of what was originally Hemsworth Colliery, but since July 1967 is now part of South Kirby Colliery. Examination is made of the Barnsley Seam sections and the part played by the top section of the seam as it comes in close proximity to the main seam. In this area of the colliery nine mechanised faces were set away between the years 1953 and 1968, every one "fired" at the pillar edge and six "fired" at the face line when production had ceased. The paper deals with the different preventative measures used, from sandbag walls, cement injections, spraying with polyurethane, until finally using Mandoseal as a sealant. Since the latter method was first used, the last three faces worked in this particular area were all salvaged completely, without any sign of a heating developing.

May 23, 1905

By R. Vikram

IMAGES (Integrated Mapping Applications Graphical Evaluation System) is a computer graphics system developed by British Coal for mine planning. The objectives of the system are to increase the profitability of mined coal through a combination of direct and indirect benefits. The system is flexible and can be used in part or in full at a mine as a stand-alone system or as a remote location of a central corporate system.

Jan 12, 1992

Thermodynamical data of importance in connection with copper smelting have been reviewed and a collection of the most reliable information is presented in Tables XXV-XXVIII and Figs. 67 and 6 8 (folding plate). The data given in these figures and tables consists of (i) graphs and equations showing the variations in the temperature range 0-2000°C. of the standard free energies of formation of most of the oxides and sulphides met with in copper smelting (Table XXV and Fig. 67); (ii) equations showing the temperature variation of the free energy of formation of iron silicates (Table XXVI); (iii) graphs showing the variation with temperature in the range 1000°-1600°C. of the standard free energies of the principal reactions occurring in the smelter (Fig. 6 8 ); (iv) the standard heats of formation at 1200°C. of the main iron and copper compounds and gases reacting in the smelter (Table XXVII); (v) the standard heats of reaction at 1200°C. of a few of the reactions for which the free energy relationships were given in Fig. 6 8 (Table XXVIII). The data presented are discussed in more detail.

Jan 1, 1953

By Winmill T. F.

Among the various theories proposed to account for the spontaneous ignjtion of coal, one which has at times been very strongly held is that the initial heating is due to the oxidation of iron pyrites. From the results described in this paper, it is possible to calculate roughly the rate of spontaneous heating of a specimen of finely-divided pyrites, on the assumption that all the heat developed is used in raising the temperature of the pyrites, and that none is lost. It is clear that where finely-divided pyrites occurs in considerable proportion among coal, it may be the chief factor in originating combustion, but that pyrites can only be the cause of a heating when it is present in considerable proportion, and in a very finely-divided state

Dec 1, 1916

By M. L. Schmulian

"The Windarra nickel deposits display many of the characteristics that typify Archaean volcanic peridotite-associated nickel sulphide ores of Western Australia. The Fe-Ni-Cu sulphide mineralization, which comprises dominantly disseminated sulphides, occurs at the base of a differentiated ultramafic volcanic pile grading upwards from massive meta-peridotitic flows to thin, locally spinifex-textured meta-picritic units. The entire mafic-ultramafic belt has been subjected to mid-amphibolite- facies metamorphism. The ore-bearing ultramafic is immediately underlain by dominantly sulphide-facies banded iron formation (BIF), which commonly contains nickel sulphides adjacent to its contact with mineralized ultramafic. BIF-hosted ores are formed both by physical remobilization of ultramafic-hosted sulphides and by migration of Ni and Cu into pre-existing iron sulphides.At Mt. Windarra the mineralization comprises eight steeply dipping, steeply plunging elongate oreshoots, which display a marked parallelism with major and minor fold structures in the underlying BIF. Seven of the shoots occur at or close to the base of the ultramafic pile, and are hosted by at least three overlapping flows. The zone of overlap occurs at the northern end of each flow, where picritic ultramafic, representing a dominantly liquid portion of the flow, occupies the basal contact. A gross south- north ultramafic flow direction is inferred. The eighth shoot occurs in a stratigraphically higher position within the ultramafic sequence.At South Windarra at least two overlapping mineralized flows occupy the basal contact, the ore zone having a strike extent three to four times its downdip extent. There is no obvious structural control to the mineralization."

Jan 1, 1984

By T. F. Bamber

The South Nottinghamshire Area has not been greatly troubled by spontaneous combustion until the last few years, during which the Blackshale Seam has been developed and exploited. The problem was first encountered at a colliery which was heavily preoccupied with a major reconstruction scheme, and with the sudden appearance of a completely new hazard both men and management had to adapt themselves very quickly to meet the situation. The paper contributed to the Symposium by the South Nottinghamshire Area illustrates the problems by reference to actual incidents, and shows how the lessons learned from them have been applied to the shaping of future policy on the avoidance and treatment of spontaneous combustion.

May 23, 1905

By E. L. Evans

The historical development of South Yorkshire mining is traced and note made of the liability to generate spontaneous combustion of some of the seams which have been worked. The liability factor is analysed firstly as an inherent property in the material of a coal seam, and secondly as a circumstance of a situation in which access is provided for the air necessary to sustain oxidation. The geological settings in which incidents of heatings have been known to occur is discussed and conditions favouring a natural pre-disposition to spontaneous oxidation exposed, particularly the effect of argillaceous material overlying the seam. An extensive strata-dynamic study follows to demonstrate the situations in which stray air currents tend to impinge on readily oxidizable material. Prevention techniques are indicated as the identification of strata-dynamic situations in which air access to broken coal is induced and thereafter th operational action to seal off the voids which have been opened up so as to exclude air from the broken coal. Measures to reduce the tendency for ventilating air to short circuit across waste voids, and to obviate deflection of air into packs are outlined. The importance of face and roadway design features is demonstrated and the consequences of practices inimical to good control of spontaneous combustion are related. Discussions on means of detection and also on the sealant materials available are included.

May 23, 1905

By Mowat D. M., Louis H., Smith W. Mackey W. M., Dron R. W., Ellison C. C., Winmill T. F., Kerr G. L., Haldane J. S., Ashworth J., Garforth W., O'Shea L. T.

Discussion of Winmill's paper, including various anecdotal examples, is presented together with the author's response; topics included: the need to distinguish cubic pyrites from the rapidly decomposing rhombic form known as marcasite; the effects of moisture content in the coal and air; the possible effect of pressure; the heat insulation resulting from heap/stack size; and the means of determining pyrite and moisture contents

Dec 1, 1916

By Dean S.

Further discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 12th February 1916, with Mr. T.Y. Greener, President, in the chair, of the paper published in Trans. I.Min.E. vol.L, 1915, p.179 and 388. Written contributions to discussion included Mr. Dean's reply to earlier discussion (p.35-44), further written contributions by Tate S. (p.44-54) and Brown E.O.F. (p.54-56), and oral comments by Hare S., Merivale J.H., Greener T.Y. and Tate S. Particularly debated were the causes of the difference in output between American and British coal miners

Dec 1, 1916

Discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 8th April 1916, on the paper published in Trans. I.Min.E., vol.LI, 1916, p.72-90, included written contributions on size and gauge standardisation by Lupton A., Peck W.R., Dean S., Mayer R.W. and Ashworth J., with the author's written response, and by Bulman H.F. and Brown M.

Dec 1, 1916

By J. H. Chesters

The main, though rarely mentioned advantage, is likely to be the standardisation of best practice and product. In a batch process conditions vary cyclically, but with a continuous process they would, at least ideally, remain the same for long periods of time. The other main advantages of continuous over batch processes are likely to be reduced operating and capital costs, the improved possibilities for automatic control, and more consistent product quality. Recent developments are surveyed for ironmaking and steelmaking with reference to blast furnaces; solid-product and molten-product direct reduction; the trough-type processes of Thring, Worner, the Japanese National Research Institute for Metals and Glinkov; basic-oxygen furnace (LD) variants; spray steelmaking; continuous casting and vacuum degassing; rolling; and coating. Encouragement in the devleopment of continuous processes may be drawn from the way unexpected difficulties, such as trouble with sulphur and refractories, were tackled and overcome to achieve the float glass process

Dec 1, 1971

By M. C. Amiri

The plant produces 130 kg slag per tonne of crude steel, to add to the basic oxygen steel-making converter slag stockpile of around 2 500 000 t. The slags contain 1.81% V2O5, which can be rendered water-soluble by salt roasting with NaCl and an alkali such as Na2CO3. Preliminary tests gave less than 3% V recovery from slag under optimum roasting conditions when NaCl, NaCO3 or Na2SO4 was used, but showed that sodium phosphate could make all the V water-soluble when roasted with slag in a ratio of 3:1 at 1 100-1 200 degrees C. Almost complete leaching was obtained within 2 h with water at boiling point. Sodium vanadate was precipitated by acidifying the leach liquor with HCl to a pH of about 2.2

Jun 21, 1905

Discussions of the papers with a written contribution on Paper No. 11 and authors' written replies. Also brief obituary of Dr. T. David Jones on p146.

Jan 1, 1947

By J. P. Ress

In 1903, seventeen years after mining of the Witwatersrand gold-bearing reefs started, the findings erf the Miners' Phthisis Commission (Transvaal) resulted in the initiation of measures with the object of controlling dust production. The substance of these measures was as follows: Removal of persons from places where they would be exposed to blasting fumes; use of water to suppress dust made in drilling and in other operations; supply and control of air to working-places; filtration of dusty air; and determination of the amount of the dust in the air. Broadly speaking, progress in dust control has followed these four lines with increasing success as the nature of the problem has become better known. Complete success has not, however, been achieved, partly because increasing mechanization of mining has intensified the problem and partly because the application of these measures is not infallible, being subject, in many cases, to human control. A brief summary of the development of these measures will lead to a description of present-day practice.

Jan 1, 1947

By Gibson J.

Written discussion contributions to the paper presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 12th February 1916, with Mr. T.Y. Greener, President, in the chair, comprise comments by Kilpatrick W.M., Routledge W.H., Watson J. and Smith W., along with the author's reply. Also briefly noted are the demonstration of two pieces of equipment, an incline chock and a cage arrestor

Dec 1, 1916

By L. R. Chimimba

"The Trojan nickel deposit occurs within a pile of ultramafic lavas subjected to a lower amphibolite grade of metamorphism. The lavas form part of the Upper Greenstones (Bulawayan Group) of the Mazoe greenstone belt. The nickel mineralization occurs as disseminated, massive and near-massive sulphides. The massive and near-massive ore occurs along the basal contact of the serpentinite units and is overlain by the more abundant disseminated ore, which occurs within the serpentinite. The main sulphide minerals are pyrrhotite. pentlandite and chalcopvrite. Minor amounts of millerite and pvrite are present. The Ni : Cu ratio in all three types of ore averages 15:1.The intercumulus nature of sulphides in the near-massive ore and similar textures occasionally seen in the disseminated ore indicates a magmatic origin of the mineralization. The basal position of the near-massive and massive ore suggests that the sul­ phides settled out under gravity during the emplacement and crystallization of a peridotitic magma. The deposit has been deformed and some of the primary massive ore has been remobilized into veins and breccias. The disseminated mineralization now occurs mainly as blebs of sulphides intergrown with silicate minerals or as stringers of sulphides between foliation planes in the serpentinite."

Jan 1, 1984