Search Documents

By Dale Ramsey

Located in the Chestnut Ridge Mountains of Southwestern Pennsylvania, the Casparis mine named for the founder Kenneth Casparis operated from 1916 until the early 1950. producing crushed stone for construction and railroad ballast. The rock was transported by aerial buckets to a railroad tipple nearly 1000’ (304.80 meters) below the mine. The mine property is now owned by the Pennsylvania Game Commission and is located in the Loyalhanna limestone seam with 4 primary entries that are approximately 40’ (12.19 meters) high by 30’ (9.14 meters) wide and extend over 2 miles (3.22 kilometers) into the mountain.

Jan 1, 2006

By Koichi Kurokawa, Takeo Ueda, Masahi Nakano, Yoji Tasaki

A lightning strike generates several 10kA and several billion volts, and earth currents generated by lightning is dangerous to some underground and all surface blasting operations. In order to evaluate the safety against lightning in conventional electric firing method and electromagnetic induction blasting system, a test is conducted by connecting a wire with an impulse generator. Frequency of impulse current used in the test is 17kHz and the waveform is a vibration type and the duration time is 250 ~usec. The results of the test show that induced current increases with the increasing of impulse current. In the case of MBS connection, when maximum primary current is 1700A, Maximum secondary current is 11.8A and the electric detonator is fired at this condition.

Jan 1, 1988

By Kamal Wadhwa

Ever since the introduction of Liquid oxygen explosives in India in 1927, these explosives are being extensively used in the various mining industries such as coal, ironore, limestone, bauxite, magnesite etc. The earlier LOX compositions were based on cellulosic material of Weberlox series of French origin. They contained the basic ingredients of saw dust with an admixture of cork dust, some hydrocarbons and some metallic powders. However, there were some inherent defects in the soaking characteristics of these compositions, in as much as, absorption and retention of liquid oxygen in the cartridges were not properly regulated in the fine pores and in the inter-granular spaces inside the ingredients in a uniform manner.

Jan 1, 1989

By Geoff Baldwin, Alastair C. Torrance

The use of monitors to assess equipment performance is carried out on a routine basis in many industries. The benefits gained through process control in knowing exactly how the equipment is working far outweigh the initial capital costs of the monitor. In the mining industry several dragline monitors have been developed and installed on equipment through out the world, but to date none has been fully accepted by the industry. This paper describes the use of a sophisticated monitoring system which incorporates an onboard processor to assess both dragline and blast performance. The use of a radio telemetry link for data transfer has removed the need for manual data collection and transfer, leading to a more efficient and powerful system. Significant effort has been put into the development and verification of a dig index to allow blast performance to be objectively assessed.

Jan 1, 1990

By Jack Eloranta

This paper describes a method of evaluating shot performance through the use of available mine- data. The mine had already been monitoring the following parameters for other purposes: drill penetration rates, shovel loading rates, crusher throughput, crusher power and crusher hangups. By assigning pit coordinates to these factors, maps showing the location of difficult and favorable blasting are as are identified. Products and techniques are compared by the same method.

Jan 1, 1993

By Ray Jambakhsh, Craig Copping

The St. Lawrence Seaway's Welland Canal has been undergoing a rehabilitation program that requires the removal of deteriorated concrete from the 25 meter high lock walls. Multi million dollar contracts must be completed during the three month winter freeze up. New blast designs have drastically cut the time required for concrete demolition. All blast results including vibration, noise, underbreak, overbreak, scaling and flyrock have been improved and at a lower cost.

Jan 1, 1994

By Virgil J. Stachura, Larry R. Fletcher, Matthew N. Plis

Falls of ground remain a leading cause of fatalities and injuries in underground mines. In response to this situation, the Bureau of Mines conducted a series of experiments in the White Pine room-and-pillar copper mine which resulted in smoother, safer ribs due to a reduction in the amount of overbreak caused by blasting. The tests evaluated the effects of changes in the loading of the rib holes of the mine's 20- by 28-ft drift round driven in shale and sandstone. The relative integrity of the ribs remaining after the blasts was measured using both photographic and seismic refraction techniques.

Jan 1, 1989

By P Cotton, N Cox

The Brisbane City Council has implemented a program of continual improvement at its Mount Coot-tha Quarry in the heart of Brisbane, Australia. The program has been underway for the past 6 years, and has resulted in very significant improvements in terms of both the cost effectiveness of its operation, and in terms of its environmental impact on nearby residents. The work has included a focus, amongst other things, on blasting efficiency, and has challenged conventional thinking in terms of the size of blasts fired, the frequency of firing, the diameter of blastholes, and the use of bulk emulsion or slurry explosives.

Jan 1, 1995

By Shijie Qu, Paul N. Worsey

Pre-splitting has become widely adopted for the formation and protection of final surface rock excavation profiles in both large scale civil construction and highway rock cuts. Jointing has been shown to affect the success of pre-splitting and the smoothness of the resulting profile, however, only closed joints have been investigated. Frequently jointing that is closed at depth is open at and near the surface due to weathering, reduced stresses and ground water percolation. In many instances, problems are associated with surface rock layers whereas at depth these problems are either reduced or do not exist.

Jan 1, 1987

By Paul N. Worsey

Disturbed zones of rock have been measured for blasted highway rock cuttings by Matheson and Swindells of the Transport and Road Research Laboratory (TRRL) of Great Britain. These zones have been shown to be directly attributable to the blasting process and accordingly vary in depth depending on blasting technique. Perimeter blasting such as smoothwalling and pre-splitting has been shown to be effective in reducing the depth of disturbed rock. Although extensive work has been carried out on surface excavations for medium diameter (l00mm) blast holes, none has been undertaken for underground excavations.

Jan 1, 1985

By Conny Sjoberg, Finn Ouchterlony, Bjorn Jonsson

This contribution reports an investigation of the blasting damage in the contour of an access ramp to a Swedish underground laboratory for nuclear waste related studies. Near zone vibration measurements were made for 7 rounds and the results converted to a site specific scaling law. A simple engineering correction for the influence of the charge length wee developed and the resulting equations used to predict the damage zone depths of three different drilling and charging patterns.

Jan 1, 1993

By Richard J. Mainiero, James Q. Wheeler, Lewis H. Kopera, Yael Miron, Solin S. W Kwak

The research reported here was part of an effort to evaluate the safety of a process to recover TNT from MK-9 depth bombs by the autoclave meltout process. In this process the depth bombs are heated to 121oC so that the TNT will melt and run into a vat. Unfortunately, asphalt lining the inside surface of the bomb also melts and flows out with the TNT. Prior to this study, it was not known what effect the asphalt contamination and the higher than normal process temperatures (121oC) would have on the sensitivity of the TNT.

Jan 1, 1996

By Thomas A. Simpson, Yung-Kwaun Jow, Dennis L. Gamble

Construction of the $200 million Riverchase Galleria Mall in Hoover, Alabama was started in early 1984. The construction area consists of about 70 acres. The extensive building complex requires heavy concrete foundations which have to be poured during the early stages of construction and on a nearly daily situation so that contractual agreements can be met on a timely basis.

Jan 1, 1985

By Gregory S. Parker

The explosives community has seen tremendous technological advances during the past several decades. When this industry was in it's infancy and even past, Powder Monkey's defied the odds by relying on daring and cunning to unleash the power contained in nitroglycerin and black powder. Unlike the manufactured improvements, there has been little in professional evolution amongst the blasting fraternity unless provoked (for the most part) by the government. It is the intent of this author to advance the cause of an industry wide training and certification program, uniform in nature and broad-based enough to be voluntary, giving states whose outstanding programs are already in place, the opportunity to provide input. In creating this type of atmosphere, grandfathering, reciprocity and accessibility would be paramount. With ISEE taking a firm leadership role during the inception and NICET's involvement in the administration, the idea postulated here is intended to spark interest and debate, bringing the inception of such a program to the forefront.

Jan 1, 1995

By John W. Kopp, David E. Siskind

Over 4 billion pounds of commercial explosives are used by the U.S. mining industry every year with an excellent and improving safety record. However, accidents involving explosives are seldom minor. They produce a disproportionate amount of fatalities compared to other mining activities, as reflected in the relatively high severity rates. The U.S. Bureau of Mines (USBM) has been analyzing blasting accident data obtained from the Mine Safety and Health Administration (MSHA) to determine the most frequent causes of mine blasting accidents, examining trends in these accidents, and identifying areas of needed research. This paper is an update of three previous blasting accident studies conducted on 4-year intervals by the USBM and published in 1983, 1987, and 1991, and is based on a total of 869 blasting accidents.

Jan 1, 1995

By Salah A. Taqieddin

The blast casting technique of removing overburden is an innovative technique which was successfully used in the mining of certain surface coal and quarries. This method was found to be efficient in minimizing the labor and equipment cost while accelerating mining operation with safety. This method was successfully applied to horizontal as well as to dipping coal seams. Also it was practically applied to single as well as to multiple ore bodies

Jan 1, 1992

By J Foklesi, G Bohus, D Benedek

The breakage process in blasting takes place in space and in time and the latter will determine the degree of fragmentation, shape of the muckpile and the extent of displacement. The shock wave travels at the velocity of sound in the material and it can easily be measured. The cracks' velocity is only 0.38 % of the velocity of sound. The number of cracks at any distance from the explosion cavity, their length and the time of development can be calculated.

Jan 1, 1986

By Sarma Kanchibotla

In mineral industry operations the insitu ore is’separated from the waste rock and is subjected to a series ofprocesses to convert it into a valuable product. Profitability of any operation in this industry depends on how eficiently the insitu rock (ore -I- waste) is converted in to the final product and how much value @ice) it commands in the market. Traditionally, the total process in mineral industry is classt@ed into two groups as mining and milling, and optimised independently without considering the impact of one over the other. This paper investigates the impact of mining operations (especially blasting;) on downstream processes and demonstrates the potential benefits of the “Mine - Mill Blasting” approach through simulations and case histories.

Jan 1, 2000

By A. Pope

I have attended two Explosives Engineers’ Conferences in the past 4 years. The first was in Brighton, England with the European Federation of Explosives Engineers in 2005 and the International Society of Explosives Engineers in New Orleans, USA in 2008. At both of these conferences I listened to papers presented on European and English training methodologies and ideologies. As I have been training Shotfirers for the past 18 years in Queensland and the Northern Territory for some 8 years previously, I would like to present our methods of training in Queensland, which I believe is among the best in the world. In Queensland, this training is carried out by a training organisation that is registered by the Department of Education, Training and the Arts under the guidelines of the Australian Quality Training Framework (AQTF). Not only is this Registered Training Organisation (RTO) required to operate under these very comprehensive guidelines, but also those designated by the Explosives Inspectorate of the Queensland Department of Mines and Energy.

Jan 1, 2009

By Guillermo Silva

A novel, ultra-low density explosive composition, particularly suited for wall control and other applications requiring customising of the explosive’s energy output, has been developed. Being reactive in nature, the low density explosive enables the controlled dilution of dry blasting agents from their nominal densities down to values slightly less than 0.10 g/cm3. The product has been detonated at densities of 0.07 g/cm3 in diameters as small as 50mm under confined conditions, using a 227 g (l/2 lb.) primer. Recorded velocities of detonation ranged between 1200 m/set and 2200 m/set for densities between 0.07 and 0.2 g/cm3. Theoretical velocities ranged from 1700 m/s to 2500 m/s for the same density range. The low density explosive was insensitive to initiation by a blasting cap which is a desirable feature for transportation purposes. Mixing of the product with ANFO has been accomplished with minimum segregation making it suitable for applications where reduction of pressures are necessary.

Jan 1, 2000