Search Documents

By Francisca Tapia, Jorge Blázquez, Paulo Couceiro, Patricio Vergara, Luis Manriquez, Luis Martínez, Juan Navarro

Efficient energy transmission is critical for effective rock fragmentation in open-pit blasting. However, in zones with highly fractured or soft rock, mismatches in acoustic impedance between the explosive and the rock can lead to significant energy loss. These mismatches reduce fragmentation efficiency and, when energy input is increased to compensate, can trigger unintended side effects such as NOx fume generation. This paper presents a novel methodology that integrates the Fragment Size Energy Fan model with acoustic impedance theory to dynamically optimize explosive energy delivery. A redefined impedance formulation captures volumetric energy transfer and enables the calculation of a Rock Impedance Factor (RIF), calibrated through non-linear regression. To operationalize the model, rock impedance is estimated using the X-4Traits Model—a meta-learning algorithm that interprets Measurement While Drilling (MWD) data from both autonomous and manually operated drills to produce high-resolution, spatially distributed impedance maps. The methodology was calibrated and applied at Minera Escondida Limitada (MEL), using data from over 218,447 blastholes and 526 blasts. Two case studies illustrate its application: Expansion 1 demonstrates improved fragmentation consistency and a 10.7% reduction in powder factor by aligning explosive energy with local impedance variations; Expansion 2 highlights the model’s utility in managing NOx emissions in fractured zones by optimizing energy distribution and confinement without compromising fragmentation. This impedance-based framework provides a robust tool for improving fragmentation outcomes, optimizing energy use, and enhancing control in geologically variable blasting environments.

Jan 26, 2026

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is commonly adopted method in underground hard rock mining. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason being the unavailability of free faces as compared to open cast bench blasting. The geological and geotechnical parameters changes gradually even within the stope itself. So the blast design parameters should be planned according to the scenario of upcoming ring. Blast design parameters like burden, toe spacing, inclination of blast holes, diameter of blast holes, charge density of explosive etc plays an immense role in rock damage. For the proper breakage of rock, the movement of burden is prime objective. To study this, explicit dynamic based modeller of M/s Ansys was used. The burden values were varied from 20-65 times diameter to assess optimum burden value during the study. The models were simulated for the rock having 35 MPa uniaxial compressive strength and 102 mm blast hole diameter. Altogether three holes were blasted having hole depth 14-14.5m. The blast design parameters and respective blast induced ground vibration has been measured at the experimental site. Core sample of the rock of experimental site has been used for the evaluation of geotechnical parameters. These geotechnical parameters were inserted into the simulation model. The volume of rock excavated along free face has been calculated in each model. It has been found that the burden value can varies from 35-40 times blast hole diameter (3.6-4.1m) to achieve greater volume of rock along the free face for 102 mm blast hole diameter and rock of 35 MPa uniaxial compressive strength.

Feb 6, 2023

By J. Silva, M. Kotraba, F. Pontanilla

Blasting is the application of highly complex science that, in some cases, could be viewed as an art. Many variables are involved in a blast, including geology, pattern design, timing and firing sequence, and explosives selection. Assuming that better results can be achieved by only increasing the powder factor is inaccurate. The Drill-to-Mill (D2M) concept has been in the mining industry for over two decades. The D2M approach is commonly viewed in an oversimplified manner, assuming that by simply increasing drilling and the amount of explosives used (both of which add operational costs), the downstream value will be created. An optimized D2M initiative should combine the smart application of explosives at the beginning of the mining process, matching the dynamic properties of the rock to the explosive selected to improve the efficiency of the energy created by the explosive to the rock mass being blasted, and to bring benefits to the mining operation across the entire mining and processing value-chain. This paper reviews the principles behind matching the shock impedance of the rock and the explosive and compares the traditional use of explosives versus the smart application for two hypothetical blasts.

Jan 1, 2024

By Raúl Carretero de la Hoz, Leonardo Soares Chaves, João Paulo Soares Toneli, Francisco Felipe da Silva Dantas, Marcos Peres Lopes, Marcus Vinicius da Silva Gonçalves

The mining activity results in environmental impact and thus requires the adoption of techniques to minimize its effects. The rock blasting process is required to break up and move the rock enabling the haulage of the material, however, it might also cause undesirable effects such as flyrock, overbreak, excessive ground vibration or air-blast at the neighboring communities and damage to civil or geological structures located nearby. The Serra Sul mine, commonly referred to as S11D project, has obligations to preserve two natural tropical montane lakes and several maximum relevance natural cavities whose legal preservation radius represents constraints to the mine development and operation. Controlling measures are undertaken to ensure preservation of the cavities, especially during rock blasting stage, with limitations of the maximum instantaneous charge (MIC) and ground vibration control. The demand for high productivity and the large areas with hundreds of blastholes to charge are challenging factors to the charge control. This work presents the development and field application of a map for limiting explosive charges in the rock blasting process at the Serra Sul mine, used for the definition of maximum charges according to the blast location, ensuring the preservation and compliance with the defined ground vibration limits for each cavity. The map is applied at the mine for every blast and when there is a charge constraint, the map helps to define the areas with different charging profiles in the field contributing to higher charging productivity.

Jan 21, 2025

By Enrique Munaretti, Cathy Aimone-Martin, Vitor Rosenhaim, Jair Koppe

Production blasts at one of Copelmi’s coal mine operations will be carried out 100 m (330 ft) from a neighborhood located in the town of Butiá, southern Brazil. Mine management is concerned about the possibility of damages and complaints due to blasting operations at close distances to structures of substandard construction. Blasting in the area is characterized by the use of very low powder factor resulting in confined shots in which movement is restricted to a point of almost undershooting the rock. Over the past year, tests were conducted mainly in the overburden area to determine the best approach to be implemented when blasts move closer to the town. Mine management wants vibration levels to be reduced lower than the damage limits proposed by Brazilian regulations to ensure a safety margin and mitigate perception by the community hoping to reduce the number of complaints.

Jan 1, 2013

"In this work a blasting seismograph was tested on a vibration shaker controlled by a single-point laser Doppler vibrometer (LDV). A total of 43 tests were made to measure the transfer properties(transmissibility and phase shift) of the basic elements of the full monitoring chain and investigate theperformance of the full system. The main elements of the seismograph are described by second ordertransfer functions with typical parameters calibrated through nonlinear fit of the measured responses. The resulting transfer function is used to compare the behavior of the tested seismograph with fourtheoretical seismographs representative of those used in blasting. Fifteen theoretical inputs are runthrough the transfer function of each seismograph to assess their steady-response. The error (expressed as gain) in the peak velocity has been assessed. It varies from -1.5 to 2.3 dB (equivalent to atransmissibility of 0.84 to 1.3, respectively) depending on the seismograph and frequencies of the input.The largest errors occurred for input signals with frequencies in the low (<32 Hz) or high ranges (>125Hz), where the mechanical, electronics and digital parts of the seismograph modify the signals. Seismographs with the nominal transfer function described by DIN 45669:1:2010 are ranked with the smallest errors. Monitoring devices with transmissibility around one in a narrow bandwidth, in line with ISEE suggested criteria for amplitude response, involve large phase shifts at low and high frequencies, resulting in a worst performance."

Jan 1, 2017

By O. Rielo, A. Pascoal, P. Katsabanis

The dynamic parameters of two different granites have been obtained using Hopkinson bar experiments. One series of experiments were conducted using a Hopkinson pressure bar apparatus with an explosive source to provide the compressional wave. This wave would travel along the granite bar and would be reflected at the free end. Strains were obtained along the bar to examine the process. Using relatively long bars of rock, approximately 300mm long and 18mm in diameter, the separation of the compressive and the reflected tensile pulses was possible. If the net tension exceeds the strength of the material, spalling is witnessed. By properly selecting attenuation materials and explosive sources, single spalls were created, making results easier to interpret. Numerical modelling enabled the calculation of the propagation of the stress wave along the bar and its reflection at the free end. Knowing the location of the spalls, critical stress levels for rock failure under tension were obtained. Dynamic tensile strengths were also obtained, at different strain rates, using a Split Hopkinson Bar Apparatus. The results provide a measure of the increase of the dynamic strength at high strain rates, relevant to blasting applications. They are useful for the calibration of blasting models and the characterization of rocks for blast modelling, but also provide answers to the basic question of what is the rock strength for blasting applications.

Jan 1, 2011

By Ian Bell, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Mahdi Ramezani

"Image-based rock fragmentation sensing in mining and quarry applications includes an important rock boundary delineation step, which is commonly referred to as rock segmentation. This paper presents a novel approach to solve this problem, using artificial intelligence. In the proposed technique, priorknowledge of previously analyzed images is encoded into mathematical/statistical models. A set of human labeled images are used as training inputs. These images are used to train neural networksthrough an optimization process. The networks can then be used in real time for rock delineation. "

Jan 1, 2017

By Mick Lownds, Ruilin Yang

The potential advantages of electronic detonators with accurate timing have been increasingly recognized by the blasting community. However, in comparative blasts the results with pyrotechnic timing are sometimes comparable to those from electronic timing. Statistical variation in blast results is a plausible cause of these observations.

Jan 1, 2011

By Jaime Herrero, Santiago Gómez, Pablo Segarra, José Ángel Sanchidrián

This paper presents a mathematical model for the study of the 2D movement of blast bench faces based on the high-speed video analysis of three blasts at El Aljibe quarry (Spain) recorded at 2,000 frames per second. In these blasts, a set of bags of 0.75 × 0.75 m were placed in front of a selected blasthole defining a reference plane in which to study the kinematics of the movement. The burdens range from 3.86 m to 5.54 m, with a bench height of 12–13 m. An affine transformation system was calculated to convert coordinates from the video images into actual spatial coordinates. The problem is established from a multi-objective minimization approach in order to simultaneously optimize two defined objectives: trajectory fitting using Total Least Squares regression, and time–displacement regression using Ordinary Least Squares. Muti-objective minimization formulation produces Pareto plots of non-dominated solutions, i.e., optimal combinations of initial velocities and response times, (i.e. time between detonation and the onset of bench face motion). From the Pareto frontier, the most balanced solution is selected. Blast response time lasts only a few milliseconds and appears so brief at the frame rate used that it is difficult to detect visually. In this context, the bi-objective optimization-based approach proves to be a more robust tool than frame-by frame survey for quantifying such a rapid event while also maintaining a strong performance in the trajectory fitting task. Root Mean Square Error (RMSE) for the two minimizations average 0.22 m and 0.13 m, respectively. The initial velocities obtained range from 4 to 17 m/s, and the response times 0.7 ms to 21.7 ms. An analytical model is also presented for predicting fragments initial velocity and response time as functions of blast geometry and rock mass properties, explaining approximately 87% of the total variability.

Jan 26, 2026

By Stewart A. Silling, D. Lynn Gordon, C. Mick Lownds, Dale S. Preece, Ali Bhuiyan, Patrick R. Bowden

Blast heave modeling and prediction utilizing the new discrete element model, GEM, that treats rock as elements with alternating arcs and line. Explosive loading of GEM elements is accomplished by utilizing the Noble-Abel equation of state to track the gas pressure from detonation through expansion to atmospheric pressure.

Feb 1, 2020

By Catherine Johnson, Kelly Williams

Advances in high-speed video imaging make it possible to see the refraction of light due to the high-density gradient at the shock front without the need for parabolic mirrors or additional light sources necessary for Schlieren or shadowgraph imaging. The average shock front velocity between two points can be calculated by dividing the change in position by the elapsed time between the images. Using the Rankine-Hugoniot relationship demonstrated by Swisdak the peak overpressure of the shock wave can be calculated from its velocity eliminating the interference of the gage and mount

Feb 1, 2020

By Luana Ferreira de Carvalho, Aurelio Manço Garcia, Gustavo Sampaio Lopes, Jose Silvio Corsini, Davi Bastos Martins de Oliveira

The Enaex Mining Technical Solutions (EMTS) team, in partnership with the Anglo American Iron Ore Brazil drilling and blasting team, has developed a study aiming to optimize the blast design applied at the Minas-Rio project. The study consists of modeling the dynamic behavior of one lithological domain to determine the best configuration of drilling pattern, charge configuration, timing and sequencing of the blast designs applied at the mine in this particular rock. The first stage of the study was the recognition of the rock blast process in question, assessing key parameters that characterize this whole operation: geomechanical characteristics of the rock mass, implementation quality for drilling pattern and explosives charging (collar position, hole depth, explosive charge length and stemming size) and recognition of current blast designs. The central element of this study was the creation of a vibration attenuation and seed wave model which has allowed the characterization of this particular rock mass present in a region determined by the Minas-Rio team. The model is based on a near field vibration test, constituting a powerful tool in the design of blast parameters. The blast design developed from the damage model simulations basically modified the timing and sequencing. The aim of this study was to improve the fragmentation resulted by the blasting, considering the particle size requirements demanded by the primary crusher and to increase the productivity of the loading and hauling operations. The results were analyzed considering the effective productivity of the two different fleet types of shovels, where the authors have analyzed more than 46000 values of productivity from September 2017 to August 2018, taken from the Dispatch system. A significant increase in effective productivity of these load equipment was observed, 7% to the PC4000 fleet and 2% to the PC5500 fleet, values supported by statistical parameters and hypothesis tests.

By Luana Ferreira de Carvalho, Aurelio Manço Garcia, Gustavo Sampaio Lopes, Jose Silvio Corsini, Davi Bastos Martins de Oliveira

The Enaex Mining Technical Solutions (EMTS) team, in partnership with the Anglo American Iron Ore Brazil drilling and blasting team, has developed a study aiming to optimize the blast design applied at the Minas-Rio project. The study consists of modeling the dynamic behavior of one lithological domain to determine the best configuration of drilling pattern, charge configuration, timing and sequencing of the blast designs applied at the mine in this particular rock.

Feb 1, 2020

By Khiva Haidar Shauma Tassno, Zulham Ahmad, Farhan Harist Maharesi, Abdullah Badawi Batubara

Blasting operations can use a bulk emulsion explosive (EE) with a formulation based on used oil as a replacement for refined fuel oil. The most commonly employed used oil for making EE is a mineral based used engine oil that passes an impurity content standard. It is known that not all types of used oil are easily incorporated into EE formulations. Impurities in used oil can disturb EE stability resulting in crystallization and phase separation and consequently led to poor detonation quality. In 2024, a poor blast result occurred at an Indonesian mine due to utilization of used oil that was not within specification. A research project conducted from February to April 2025 found that used transmission oil differs from used engine oil in hydrocarbon composition. Transmission oil contains more additives that affect EE stability due to polarity differences and the disruption of colloidal state stability. Lab tests including stress testing and crystal growth observation aided the development of a stable EE formulation based on used oil and used transmission oil. In mid-April 2025, blast evaluations were conducted using the EE that was formulated using used engine oil and used transmission oil. Measurements of velocity of detonation, fragmentation, and digging time, demonstrated high quality EE was produced. Application of used oil in EE revolutionized the capability of mining operations to improve blast sustainability and cleanliness. Through comprehensive research, robust testing, and effective supply chain management, it is possible to replace some portion of refined fuel oil with used oil without compromising blasting performance. The inclusion of used transmission oil broadens the overall used oil specification and increases the volume of recycled used oil available for blasting. The increased volume of used oil available can reduce the amount of waste generated by mining projects while maintaining operational efficiency.

Jan 26, 2026

By Richard H. Granhom

Detonation pressure, or Chapman-Jouguet pressure, is an intrinsic property of an explosive, and like detonation velocity, is an indicator of explosive performance. Pressure and velocity are also important for calibrating computer codes and for other calculations such as the stress imparted to rock or metal by an explosive. The detonation pressures, P~cj, of many "ideal" explosives have been measured indirectly by recording some hydrodynamic flow variable other than pressure, with P~cj being inferred from hydrodynamics and the assumed Chapman-Jouguet equations. One such method is the difficult and expensive "aquarium technique''.] Commercial explosive manufacturers generally rely on estimates of P~cj generated by computer codes not explicitly designed for non-ideal explosives typically used in commercial applications. Over the last decade, U.S. national and government laboratories have developed in-situ gauge techniques such as the manganin gauge, for direct measurement of detonation pressure. Manganin is an alloy of copper, manganese and nickel, and is ideally suited for use as a pressure transducer because its electrical resistance changes with pressure, but is nearly constant with changes in temperature. A simplified manganin gauge technique adapted for use at a commercial test site is described and some initial results from measurements on commercial emulsion explosives are presented.

Jan 1, 1991

By Nikolaos Petropoulos, Changping Yi, Daniel Johansson, Håkan Schunnesson

The effect of jointing on fragmentation by blasting was investigated experimentally and numerically. Firstly the experimental results were presented. Then the numerical modelling based on the experiments was performed. The same conclusions can be obtained based on both experiments and numerical modelling.

Feb 1, 2020

By Tyler Acorn, Paul Worsey, Nathan Rouse

The effect of the hole diameter on vibration attenuation has not been incorporated in most vibration models in the blasting industry. In current vibration models, the charge weight and the distance from the blast are the two primary variables that are addressed. Charge weight is a function of explosive density, charge length, and charge diameter. This geometry-weight can complicate the isolation of the charge diameter variable.

Jan 1, 2013

By Adrian Moore, Alan Richards

"It has been common practice to set blast vibration limits for structures using an “observational”approach whereby limits are set at a level based on observations of damage, or the lack ofdamage, combined with a tendency to further reduce the permitted level due to uncertainty. Suchan observational approach was used in the USBM RI 8507 to produce the frequency dependent‘Safe Levels of Blasting Vibration for Houses’ which has become a universal Standard for overthirty years."

Jan 1, 2013

By Robert McClure, Carlton Lehman

Rendering safe explosives in an urban environment presents a unique challenge due to the safety concerns and disruption to the general public. Potential damage to the surrounding homes, businesses, utilities and transportation infrastructure are some of the major concerns when planning the render-safe operation. Engineering controls to mitigate blast effects, such as damaging air over pressure levels, material ejection and ground borne vibration, need to be implemented as part of the operation. Monitoring of seismic and air overpressure during these operations are needed to protect against potential claims when controlled or unplanned detonations occur. Two recent render-safe operations conducted in and around urban environments dealt with deteriorated, sensitive dynamite and damaged blasting caps. Utilizing innovative neutralization chemicals and processes to render-safe the deteriorated dynamite, while protecting the general public, proved to be the safest, most environmentally responsible and cost-effective way to approach the problem. In both cases, the explosives, old dynamite and detonators were found in abandoned, unlocked magazines. The dynamite was in a significantly deteriorated state, which was evident due to the nitroglycerine found leaking in,around and under the dynamite cartridges. Iron wire permissible electric blasting caps were also found in a corroded condition with exposed explosives and un-shunted lead wires. With occupied buildings within 180 feet (54.86 meters) of the magazines, any procedure (e.g. transporting, countercharging, burning) that could potentially cause a detonation was not an option. In the event of an unplanned detonation during neutralization operations, several blast mitigation methods were employed to safeguard the site. This operation and a similar one with over 1,000 pounds of crushed and buried leaky dynamite were unique since all the explosives were rendered-safe and neutralized on site. The use of advanced neutralization products and filtering processes allowed for a safer, more environmentally responsible way to resolve the problem. The magazines and all residual solids and fluids were tested and confirmed by independent labs to have no explosives residues. The effluents were treated on site, tested and met safe levels, so they were disposed of at a local municipal wastewater facility.