Search Documents

By Tony Rorke, Sydney Thabethe

A large overburden blast was carried out at Douglas Colliery, Middelburg Mine Services, close to a national road in South Africa. The road is a busy route between Witbank and Bethal and damage to the road could not be risked. The section of road next to the blast was particularly prone to damage, because it had been mined out on its eastern flank, and the large blast was to take place on its western flank. There were thus three potential damage risks: 1. Fly rock damage to the road surface 2. Vibration damage to the road substrate 3. Damage caused by bulk displacement of the block supporting the road into the void on the mined out side. This paper presents the design and blasting methods used to control the blast and avoid these three risks. Electronic delay detonators were used in multi-decked holes. Signature data were used to determine the blast timing to make sure that delays were used that would provide destructive interference. The timing direction and sequence was decided using wave interference patterns to direct repeated shocks away from the road. The precise detonators and the odelling capability allowed effective control of the blast vibration result. Each hole was charged with two explosive decks separated by a deck of aggregate to limit the charge mass fired per delay and thus limit the reaction forces acting towards the unsupported road. The vibration and blast results are presented in the paper, together with the design that was applied. Details are provided on how the blast was charged and primed. The detonators that were used are described and the timing design is presented.Copyright © 2004 International Society of Explosives Engineers 2004G Volume 1 - Blasting Next to an Unsupported Road Using Electronic Detonators 1 of 13 It is concluded that damage risk to nearby structures can be effectively controlled using electronic delay detonators, provided the appropriate modelling is applied to obtain the most effective delay periods.

Jan 1, 2004

By Vitor Barcelos, Eduardo Elói, Gabriella Vaz, Davi Oliveira, Leandro Silveira

Following a routine production blast at Vale S.A.'s Itabira Mine in the Quadrilátero Ferrífero region of Minas Gerais, Brazil, nearby residents registered complaints about blast-induced vibrations. Analysis of the blast footage revealed that multiple blastholes were detonated simultaneously, resulting in a higher-than-expected charge per delay, ground vibration and cratering even though the electronic delay timing was configured correctly. Subsequent blasts within the mine's soft schist region confirmed the occurrence of sympathetic detonation. Mitigating or eliminating this phenomenon is critical for the mine's operation. Two dynamic pressure tests were conducted using carbon resistors together with typical VOD monitor maintaining the standard booster, electronic detonator, and a blend of 70% emulsion with 30% ammonium nitrate explosive. The tests involved increasing the distance between the central hole (detonated first) and the four surrounding holes in a five-hole sequence. Unfortunately, sympathetic detonation occurred in all these tests. To address this issue, a new explosive with a lower density and detonation velocity was tested. This approach proved promising, as no sympathetic detonation occurred. By leveraging the data obtained from this study, engineers can now identify situations at risk of sympathetic detonation and implement preventive measures, such as selecting the appropriate explosive and recommending safe minimum burden and spacing settings as well as confinement level for each blast while maintaining the desired level of rock fragmentation.

Jan 21, 2025

By Michael Laing

Blasting regulation and restrictions are tougher today than ever before. When blasting in population centers, strict limitations are often placed on the environmental effects caused by blasting, more specifically vibration and overpressure. Blast-induced vibration can be a tricky thing to manage at times, but there are a variety of options at our disposal to help optimize and manage vibration. This paper focuses on the application of rudimentary signature hole analysis to optimize blasting vibration in localized areas surrounding a mine.

Jan 1, 2017

By Scott G. Giltner, Alex Schwenk

Blasting within 250 ft of a crusher was successfully executed through the application of electronic detonators, 3-D imagery, signature hole analysis, custom loading of blast holes. The blast was well contained, the vibrations were minimal, and there was no flyrock.

Feb 1, 2020

By John Wall

The use of electronic detonators in civil tunnelling applications, to reduce vibration is small firings has been successfully utilised for a number of years. As part of the mining industry’s commitment to reducing blast damage during the development cycle in underground mining applications, a series of development blasts using eDevTM electronic detonators in typical mining applications was conducted in North Queensland, Australia.

Jan 1, 2012

By Sandy Tavelli, Thomas L. Barkley

This discussion will present a case study in developing solutions to a metropolitan quarry’s public relations, legal, environmental, and productivity problems. It details an extensive and detailed project to address the blasting practice in a medium sized quarry that is surrounded by residential and industrial zones. The principle work was done over a four-month duration during the normal production season. It included detailed drilling and blasting audits for baseline information. In addition, geologic characterization, seismic modeling, correction of deviations from best practices, and implementation and monitoring of precise electronic timing to provide dramatic solutions for the quarry. The quarry is in the near suburbs of a large metropolitan city. It is framed on two sides by residential municipalities and on two sides by industrial zones. At the start of the project, the quarry was in court as a result of the lawsuit by one of the neighboring towns that was suing to close the quarry. The lawsuit had progressed to the advanced stage where in the Judge had appointed an arbitrator to make the decision of continued operation. This arbitrator was to observe our progress and recommend to the Judge the disposition of the case.

Jan 1, 2004

By Michael Milstein

Northwest Research Station said as more and more older dams are removed to benefit fish, it’s become clearer that rivers rework themselves quickly.“Where the dam is relatively small, it’s a quick response,” he said. “The river quickly forgets.”

Jan 1, 2010

By Brian Lewis, Reinhold Daykin Schnell

Blasting is the primary and most effective method for breaking and moving material at most mine sites. The blast design is often adjusted in efforts to optimize the effectiveness of the blasts’ explosive energy while minimizing costs. When adjusting blast design parameters, it is important to adjust one parameter at a time, observing and analyzing the potential effects of the change on the overall blast performance.

Feb 6, 2023

By Paul Worsey, Yasutaka Dote

The choreography of large fireworks displays dictates electric initiation for precise timing. It has been common practice to pre-squib products before transportation for reducing set up time. A number of fatal accidents transferring pre-squibbed product during transportation suggests that there is a problem with impact sensitivity. The aim of this paper is to quantify the impact sensitivity of the various configurations of initiating materials used in display fireworks.

Jan 1, 2009

By John S. Manka

Of the various methods used to reduce the density of emulsion explosives prior to detonation; ammonium nitrate prill addition, glass micro-balloon addition and chemical gassing, chemical gassing is the method most often selected by emulsion explosive end users. Chemically gassing emulsions costs less than adding micro-balloons and chemically gassed emulsions have better water resistance than emulsions that add ammonium nitrate prills to reduce the bulk density. Unfortunately, the chemical gassing of emulsion explosives can be intricate and is often more art than a science. To gain a better understanding of chemical gassing, we investigated the factors that may affect the chemical gassing of emulsion explosives. Variables investigated as having an effect on gassing were the pH of the oxidizer phase, the amount and type of nitrogen in the emulsifier, the composition of the oxidizer phase, the use of pH buffers in the oxidizer phase, and how the gassing reagents are added to the emulsion.

Jan 1, 2004

By Saeed Karimifard, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Frank Chu, Caitlin McKinnon, Tetiana Konstantynivska, Glen Turner

Continuing blast optimization is the cornerstone of any mine-to-mill approach, and particle size analysis is a key metric for meeting blast targets to reduce overall energy consumption and operating costs. To ensure the statistical validity of particle size data, it is important to sample material frequently. In most mines and quarries, the blasted material is loaded onto haul trucks and then transferred to the crusher; measuring the particle size of each haul truck load therefore provides an adequate sampling rate. We propose a particle size analysis solution for haul trucks that does not impact current operational workflows. Using artificial intelligence (AI) and 3D imaging technology, our solution reliably localizes and identifies haul trucks as they drive by, then accurately calculates the particle size distribution of the visible material in each truck load. In this paper, we identify the challenges of designing and implementing the proposed solution and explain the strategies we employ to overcome these. We also discuss a method for boulder detection that leverages the existing deep learning architecture to significantly reduce crusher downtime caused by oversized rocks. Finally, we present field data from a trial installation. To evaluate each change made to the blast design, it is necessary to measure the effect on particle size. An accurate particle size analysis solution is therefore the first step towards optimizing blasting practices and reducing energy consumption throughout the comminution circuit.

Hello, everyone. Way back in 1965, Devine and others at the US Bureau of Mines showed that a presplit fracture plane did not affect vibration levels transmitted across the plane (RI 6695).

Jan 1, 2010

By Abraham Lindo

Taboguilla is a small island located 10 miles outside the Panama Canal Pacific Entrance. In 2002 a fuel distribution facility was installed in order to supply fuel to vessels passing thru the canal. The current capacity of the tank farm is equivalent to 1,100,000 barrels. The demand for marine diesel at this location still exceeds the current capacity, thus an expansion project is currently underway to increase the available space for diesel tanks. There is a total of 800,000 cubic meters to be excavated in order to create the new space. 400,000 cubic meters of that total is basalt rock which will need to be blasted

Jan 1, 2011

By S. S. Bud Jenkins

I went to an underground limestone mine recently to demonstrate the use of borehole liners. The liners were for horizontal holes in a normal “V” cut tunnel round. I hadn’t been in this mine for about 40 years. What a change. Way back they used cap and fuse and lit each fuse individually with a blowtorch. The face was about 40 feet wide and 14 to 16 feet high. They used ladders to get to the upper holes. The rounds were mostly slab rounds. I never saw this happen but had heard several times that the first holes were going off before the last holes were lit. I guess if this was true the use of slab rounds was a plus for safety. As far as I know they never had an accident but it was a scary procedure. There were a lot of scary procedures in the past and thankfully things have changed.

Jan 1, 2010

By Peter Moser, Michael Messner, Florian Bauer

The existence of ammonia in underground blasting fumes was frequently measured in various field tests (6, 7). Ammonia in fumes with a TLV (threshold limit value) of around 30 ppm (slightly different in various countries) is a toxic gas but not considered to be a high risk for the underground work force as ammonia smells very itching and is extremely annoying. This might be the reason why ammonia is hardly measured in routine underground blasting fumes control. Another reason for the lacking measurement might be the circumstance that ammonia is a very reactive gas and the ammonia sensors available on the market are very cross sensitive to other gases like carbon monoxide. Nevertheless, especially since the introduction of bulk emulsion explosives in underground blasting, complaints from miners about ammonia in the blasting fumes increased. Research work by various institutions [8] around the world relates the ammonia in the fumes back to various mechanisms. Amongst others these comprise: a) non ideal (low temperature) detonation of explosives, with NH3 in the reaction products; b) reaction between rock and non detonated bulk explosives (especially when the rock is of a basic nature (high pH value); c) reaction between shotcrete and non detonated bulk explosives. Numerous blasting tests in an experimental underground set up have been made in order to check these hypotheses for ammonia origin in blasting fumes. None of them has been found to be responsible for sometimes high concentrations of ammonia in the fumes. The major reason for ammonia concentration in blasting fumes has been found in mine water of a high pH value (either natural or from using shotcrete). The mechanism identified is as follows: the moment a non detonated ammonium nitrate bearing explosive comes in contact with mine water of a high pH value, ammonia is formed immediately. The source for the undetonated explosive is twofold: firstly there is a certain spillage of explosives when the holes are charged (especially when using bulk products) and secondly not the entire explosives detonate completely. These undetonated remaining of the explosives end up in the muck pile after blasting. In case there is water of a high pH value the reaction between the explosives and the water starts immediately. This explains also the observation why ammonia can be measured in the blasting fumes quite a long time after the blast. The majority of the ammonia is not formed during the detonation; it is formed inside the muck pile even a considerable long time after the blast.

Jan 1, 2010

By Ethan Steward, Kyle Perry

Blast resistant structural design continues to be a research area of major concern for governments around the world due to explosive threats from both state and non-state actors. Glass and aluminum curtain wall systems are commonly used to clad the exterior of government and commercial structures, allowing light into the building, regulating the interior environment, and providing an aesthetically pleasing exterior. These systems are likely to fail when exposed to sudden, high-pressure events such as the purposeful or accidental detonation of explosives. Engineers have designed blast resistant curtain walls and structural elements to reduce the likelihood and severity of failure, but the design tools and testing mechanisms commonly used in the process may not accurately model or simulate actual blast conditions at all ranges. In blast resistant structural design, the origin of a shock wave is typically assumed to be in the far-field, creating a wave that is nearly planar and parallel to at least one face of the target. Shock is applied evenly and immediately across the entire impacted surface. However, the source of real-life blasts is often very close to the target structure, and the assumption of far-field planar shock does not always apply. Mid-field blasts exhibit qualities different from those assumed about far-field shocks, specifically a hemispherical shock that produces different peak pressures, impulse curves, oblique reflections, and Mach stems across a target. This paper will examine mid-field shock effects from scaled distances of 2.5 to 4 13 (6.3 to 10.1 13) on a tall, scaled target by measuring reflected and incident pressure, impulse, and shock velocity across the target. Results will be compared to theoretical blast parameter equations and empirical data used by the industry. Possible effects of mid-field blasts on structures and further research ideas will be suggested.

Jan 21, 2025

By Orica Peru, Pedro Lozada

Proper management of exclusion zones in blasting operations is essential to ensure safety without compromising operational efficiency. In Peru, mining regulations establish minimum exclusion distances specifically for personnel (500-meter radius / 1,640 feet), but do not define clear technical criteria for equipment. As a result, conservative distances such as 200 meters (656 feet) are often applied, negatively impacting productivity. This study proposes a technical-scientific methodology to reduce equipment exclusion zones, based on the use of advanced technologies such as drones, high-resolution cameras, and specialized software tools. The solutions used allow video recordings of blasts to be transformed into dynamic data through artificial intelligence and computer vision, as well as execute probabilistic simulations of the flyrock phenomenon using Monte Carlo algorithms and physical models calibrated to real operating conditions. Technological integration enabled the simulation of real operational scenarios, considering variations in critical blasting parameters that directly affect flyrock generation, such as drill diameter, explosive density, linear charge, and stemming height. Additionally, the Terrock methodology was incorporated, allowing the behavior of the rock mass to be included as a variable in risk assessment, improving analysis accuracy under different rock hardness conditions. The methodology was applied in four phases: diagnosis of the current design (15 blasts), modeling, validation of the calibrated model (6 blasts), and subsequent operational implementation. As a result, it was determined that the exclusion radius can be safely reduced from 656 to 492 feet (200 to 150 meters), maintaining as the main restriction the use of stemming lengths greater than 5.0 m. This optimization has the potential to generate tangible benefits, with estimated monthly savings exceeding USD 50,000, associated with reduced evacuation times, lower fuel consumption, less equipment wear, and increased productivity in drilling and hauling activities. The comprehensive approach presented here highlights the transformative potential of digital technologies applied to blast management, contributing to safer and more efficient mining operations.

Jan 26, 2026

By Joshua Hoffman, Philip Mulligan, Braden Lusk, Tristan Worsey

Blasters rely upon detonators to achieve the designed timing sequence to move material where it needs to go, minimize vibration, or optimize fragmentation. At times detonator inventory on seldom used delays may be slow moving. This can lead to detonators being used long after they were manufactured. This paper addresses the potential shelf life concern as it relates to timing accuracy of shock tube detonators. A recent study was conducted to study the timing accuracy of non electric shock tube detonator systems. A follow up study was then conducted to determine the degradation of the non electric shock tube systems accuracy with time. The follow up study is presented in this paper. Samples of detonators from the initial study were set aside for approximately one year and then tested. The results from the aged detonators were compared to those of the detonators that were tested in the original study. As an extreme case a third set of shock tube detonators was tested using detonators that were between eight and nine years old. The results from these tests are presented as well. Each system was tested at a short medium and long delay time. Statistical analysis was conducted to determine the effect of time on the detonators accuracy. This paper quantifies the importance of regular inventory cycling to help preserve manufactured timing when using non electric shock tube detonator systems.

Jan 1, 2013

By Bill Loviza, Jimmy Sanders

This report is not everything we would like it to be. Access to information concerning unresolved legal actions is a sensitive matter. Obtaining the information presented in this report was a challenge alone. The Tennessee Department of Commerce and Insurance, Division of Fire Prevention, the firms and individuals that elected to share information did so with various assurances of nondisclosure, confidentiality or anonymity. All those providing information did so with the expectation that the industry and ultimately the public would benefit from this effort. We offer special thanks to Assistant Commissioner, Fire Prevention, Emmett Turner, recently retired Director, Bomb and Arson, Dick Gardner and Director, Codes Enforcement, Randy Safer for support that made this endeavor possible. We make no claim with regard to being a scientific study. We did the best we could with available information. Our task was one of assembly, sorting and reporting. Where collateral information was available we used it.

Jan 1, 2004

By M. Ganster

Austria’s biggest supplier of oil and gas, transports gas through the West Austria Gasline for domestic consumption. In addition, the OMV also works as gas carrier and ensures the transit into neighbouring countries.

Jan 1, 2010