Search Documents

By Mark S. Stagg, Norman S. Smith, Rolfe E. Otterness, Stephen Rholl

Blast design parameters were studied in an attempt to quantify their relationship to rock fragmentation. The Bureau of Mines conducted a series of 29 reduced-scale shots at the University of Missouri-Rolla's experimental mine with bench size from 40 to 80 inches. Design parameters varied were burden, spacing, explosive diameter and stemming-explosive length. The shots had 3 or 4 blastholes fired at delays of 1-4 ms per foot of burden, based on previous tests that showed hole interaction could improve fragmentation by 12 to 20 percent over single-hole shots or simultaneous firing. All rock, 2000 to 23,000 pounds per shot, was screened and weighed to determine the fragmentation size-weight distribution.

Jan 1, 1991

By Paul Worsey

A strong inverse relationship between rock face movement and stemming ejection is presented. Previously unpublished data from blast control plug research and development involving high speed video analysis, which was conducted between 1986 and 1988, is presented. Face and stemming ejection velocities were calculated for tests utilizing the same bench blasting configuration comprising; a 4 ft high bench in dolomite, 3 ft burden and single 1.75 in. holes loaded with 2 ft of small diameter cartridge emulsion. The singular difference between these tests was the stemming configuration. Varying lengths of stemming were used with the presence or absence of differing experimental configurations of blast control plug. The effectiveness of this plug has been published previously.

Jan 1, 1990

By Kunihisa Katsuyama, Yuji Ogata, Yuji Wada

Test blasting was carried out to study the flying characteristics of rock mass caused in bench blasting. The quantity of explosives was increased from 7.6kg to 9.1kg and the Minimum burden was changed from 131mm to 451mm. The effect of condition for the characteristics of fly rock were considered. The fly rock was observed using the high-speed camera and video to study the flying characteristics of the rock mass caused in the bench blasting. Numerical simulation of fly rock was carried out using DDA (Discontinuous Deformation Analysis) method. It was clear that the DDA method can be applied in the simulation of fly rock caused in bench blasting.

Jan 1, 1997

By R Vuolio, B A. Jonsson

In the center of Helsinki - capital of Finland - extensive blasting operations were carried out during the years 1982 - 84. At the corner of the streets Mannerheimintie and Simonkatu - in the Forum block - about 125,000 cu.m. of rock were blasted to give place for a new modern shopping centre (Fig. 1). Added to this amount of rock another 10,000 cu.m. were blasted for a transport tunnel to an adjacent underground bombshelter (Fig.2) which is to be used as a parking place in peace-time. The blasting work was demanding and difficult to carry out due to old buildings surrounding the work-site as well as computers and other sensitive equipment installed in some of them.

Jan 1, 1985

By Dirk van Zyl

Rock fabric information is often available from drill hole information and bench face mapping. An approach is presented to predict fragment size distribution of blasted material from this information as well as that obtained after the blast. The following information available from a mineral exploration drilling program was used in the prediction of fragment size distribution: largest piece, percent particles larger than 1 inch and RQD. Photographs of bench faces were used to estimate the fragment size distribution. Fracture spacings were evaluated along a series of parallel lines on the photograph. Photographic techniques were also used to obtain the grain size distribution of blasted material. m is paper describes the methodologies applied in some detail.

Jan 1, 1986

By Brendan O'Reilly, Outokumpu Zinc, Geoff J. Johnston, S Durucan

Historically vibration monitoring has dealt primarily with surface blasting or "near field" monitoring of underground blasts. The Situation at Tara Mines is different, blasting occurs up to 400m underground, with a number of blasts occurring daily and occasionally with residential properties directly above the blasting site. Tara Mines, due to both its location (1.5 km from the rural town of Navan) and stringent planning conditions have always had to monitor, carefully plan and control the levels of vibration from blasting. The statutory vibration limit at Tara allows a maximum peak particle velocity of 7.62 mm/s with no frequency limitations. Levels of vibration have been monitored continuously since mining operations began in 1972.

Jan 1, 1994

By Mark S. Stagg, Rolfe E. Otterness, Farrokh Djahanguiri

The U.S. Bureau of Mines (USBM) evaluated empirical equations that predict fragmentation from underground stope rounds. Controlled blasting is necessary for creating leaching stopes that maximize the recovery and minimize backbreak of the perimeter wall. This paper presents the fragmentation results from one of the three drop-raise blasts used to develop a reduced-scale cylindrical stope, 1.8 m in diameter and 6 m in height. The stope is located in the Colorado School of Mines Experimental Mine (Edgar Mine) in Idaho Springs, Colorado. This stope is part of a USBM research effort to determine the feasibility of incorporating in situ leaching of rubblized stopes into active underground metal and nonmetal mines.

Jan 1, 1994

By Donald C. Clark

The Blasting Contractor as an Insurance Risk involves a discussion of changing times in the insurance market and changing methods of operation in the construction industry. Since the advent of Internal Revenue Service~1 and Occupational Safety and Health Act~2 regulations by the Federal Government in the early 1970's, operations have changed. Many small users of explosives have discontinued any use in favor of subcontracting the drilling and blasting to specialists. This change in operations along with the change in the insurance market has created coverage problems which is the subject of discussion of this paper. Although no definite conclusions are reached, it is an attempt to promote understanding and further the efforts toward equitable solutions.

Jan 1, 1977

By Quian Liu

The problem of cross-hole explosive malfunctioning in rock blasting (including sympathetic detonation, desensitization and cut-offs) is a function of delay and spacing in a blast which should be designed to avoid such occurrences. On a delay-spacing chart, the phenomenon of explosive malfunctioning is explained by dividing the chart into different regions, while the shape and size of each region could vary from one explosive to the other. Over seventy blasts have been carried out at the CANMET Experimental Mine to identify the malfunctioning characteristics of specific emulsion, water-gel and dynamite explosives. In each experiment, two parallel blastholes, 32 mm in diameter and 1.7 m deep, were drilled downwards in an underground drift.

Jan 1, 1994

By M. Szumny, P. Mertuszka, K. Fuławka

Mining-induced seismicity is one of the adverse side effects of mining with the use of explosives at great depths. Disturbance of the primary stress state by the development of the network of excavations combined with the continuous generation of dynamic loads by the detonation of explosives in mining faces has a negative impact on the level of safety of crew and machines. To ensure the stability of excavations it is necessary to identify in detail the nature of the seismic hazard by means of continuous seismic measurements. Unfortunately, the technologies used so far are characterized by high costs of installation and further maintenance, which clearly limits the possibility of using a large number of stations in a small area. A breakthrough in this matter may be the technology of microelectromechanical systems, which is several times cheaper than standard solutions used in mining seismology. This technology, with the appropriate configuration of devices, can be successfully used to monitor dynamic phenomena generated by mining activities. As part of this study, the assumptions and configurations of a prototype 42-channel accelerometer network using MEMS technology have been presented. The network was installed in the Lubin underground copper mine in Poland in a seismically active area, where multi-face destress blasting are conducted regularly. As a result, 14 tri-axial accelerometers were installed in the immediate vicinity of the active mining front at a distance of about 1,000–4,000 ft (300–1,200 meters) from the closest faces. Highfrequency recordings are collected based on algorithms that trigger the system when the Peak Particle Acceleration set value is exceeded or on the basis of a manual external triggering device connected to the blasting machine. During the measurement period, several high-energy seismic tremors and several dozen of waveforms generated by blasting were recorded. The obtained results are the basis for assessing the effectiveness of the destressing measures and for the analysis of geomechanical risk based on periodic analysis of the velocity of seismic wave propagation

Jan 1, 2024

By Joshua Hoffman, Braden Lusk, Perry Kyle

With the advent of any new technology comes the necessity of fully understanding the mechanics of that technology. The Shock Tunnel is one such technology that provides a cost effective means of simulating large-scale explosions while requiring a fraction of the explosive and space. Although the technique is known and practiced, the dynamics and mechanics of this technology has yet to be fully understood. A relationship between the energy potential of a given explosive and the energy realized at a set of distances was determined. This data was then compared to the energies realized from the same explosive when utilized in conjunction with a shock tunnel. A relationship between potential and realized energy outputs from explosive based shock tunnels exists and the understanding of this relationship would allow all for predictions to be made to forecast a specific amount of explosive required to produce a desired energy output. This energy output should then be relatable to peak pressures produced via the shock tunnel. Two shock tunnels are currently accessible for this study, the first under the direction of the University of Kentucky, and a second under the direction of the Missouri University of Science and Technology. The two shock tunnels differ in dimensions but share common construction materials. Energy realized from a shock tunnel is hypothesized to be a function of the shock tunnel’s dimensions. This study explores how different geometries affect the shock tunnel’s performance; this exploration is broken down into three phases. Phase 1: Open arena testing in which theoretical energies produced by the detonation of small (<1.0 kg) charges are compared to actual experimental values. Phase 2: Shock Tunnel testing in which realized energies are experimentally recorded for the UK shock tunnel. Phase 3: Analysis of the data to lay down the ground work for producing a pressure-forecasting tool given shock tunnel dimensions and explosive characteristics with the possible detection of avenues for optimization of shock tunnels.

Jan 1, 2009

By Ron J. Elliott, Corry Coumans

The following is a detailed description of the blasting procedures used in the successful demolition of the Stave River bridge, Mission, British Columbia, Canada. This highway bridge spans a highly sensitive salmon-spawning river. Demolition of the bridge took place in a high liability situation in close proximity to sensitive structures. The new highway bridge carrying an exposed 150mm diameter gas line was located only 1.5 meters away. The bridge piers were blasted only seven meters from overhead power lines. Control of blast vibration, flyrock, and underwater overpressure was critical to the success of the operation. Electrical sequential blasting was used to ensure that blast vibration on the new bridge structure was kept below 50mm per second.

Jan 1, 1998

By R Yang, P D. Katsabanis, W F. Bawden

Understanding the mechanisms which are taking place during the propagation of a stress wave generated by an explosive charge is of high importance in the detection, characterization and prediction of blast induced damage to the rock. Vibrations caused by the detonation of an explosive are suspected to contribute significantly to the extension of the damage zone. Vibration monitoring close to a blasthole is a relatively new field of research, the hindrance being the scarcity of transducers capable of sustaining extreme accelerations without damage. This paper focuses on the vibration monitoring aspect of a blast induced damage study; the experiment took place at Queen's test site and was meant to record near-field vibration as close as 1 m from 100 mm diameter blastholes.

Jan 1, 1993

By M. Khaled, K. Abdel Rahman, M. Khattab

Helwan limestone quarry is located at a distance of 35 km (21.7 miles) to the south of Cairo downtown. Drilling and blasting operations are used to extract the limestone for the Helwan Cement Company (HCC). In 1980’s a new urban community was constructed adjacent to the quarry. This situation led to shifting of the old quarry 5.0 km (3.1 miles) to its current location, to avoid causing blasting problems to the new community. Unfortunately, the new quarry is opened in a highly faulted area, with weak zones of brittle materials. The drilling and blasting crew is facing many difficulties due to the geological complexity along these zones. Moreover, the extension of this community towards the new quarry makes the control of ground vibrations is very important.

Jan 1, 2008

By Earl C. Hutchison, John Loviza

At the Metropolitan Nashville International Airport, with its more than 600 scheduled daily flights from American Airlines hub operations, other scheduled airline flights, Tennessee Air National Guard operations, as well as numerous industry air flights, the excavation of 300,000 cubic yards of rock was required without disrupting airport operations for a cut and cover underground tunnel with a 4 lane US Highway and new airplane runway to extend across it's top. In addition to the excavation, the removed rock was to be broken to specification type that was clean and of small size for fill in another area of the airport property. The blasting was limited to two 1/2 hour windows per day and stiff monetary penalties were in place for schedule slippage of each phase of the project.

Jan 1, 1992

By Paul Worsey, Seokbin Lim

In many high explosive applications, the explosives are covered or clad by a metal. This metal cover may serve a variety of purposes including: 1) to protect and prevent the disturbing or misshaping of the explosive during its transportation, handling and use, 2) in many military applications the cover material itself is used to provide a required effect, for example, the shrapnel from grenades, the metallic liner of shaped charges, and the confinement of explosives so they perform optimally, and, 3) in civilian applications in the use of well perforating shaped charges and linear shaped charges used for the demolition of steel structures such as bridges. For these reasons the interactions between the explosives and their covering materials are of great importance in understanding the performance of these devices.

Jan 1, 2005

By John T. Aler

The U.S. Bureau of Mines has been studying the problem of why explosives detonate weakly or misfire during blasting in underground coal mines. Cross-borehole shock wave interaction has been identified as a predominant mechanism causing explosives to function improperly (1)(Underline numbers in parenthesis refer to items in the list of references at the end of this report.). Cross-borehole shock wave interaction can be simulated in a laboratory setting, making possible the replication of tests in sufficient numbers to understand and quantify some of its effects on permissible explosives (2). The work presented here investigates the capacity of explosives to partially recover from the desensitizing influence of the shock wave. The recovery trend of different explosives can indicate optimum blasting patterns useful for minimizing borehole charge malfunctions.

Jan 1, 1991

By Ben Barrett

Dangerous goods, known as hazardous materials in the USA, are subject to special controls during transport to ensure the safety of the public. Dangerous goods are divided into nine classes, and Class 1 is devoted to explosives. Unlike storage or manufacturing, explosive transportation crosses the political boundaries of localities and nations, and its regulation must be centrally managed to avoid duplicate costs of complying with multiple regulations. Additionally, the transport of dangerous goods occurs by four different modes – highway, rail, vessel and air. While each mode has differences which must be addressed, the fundamental principles of classification, packaging, hazard communication and documentation remain the same. When a shipment travels by multiple modes and across borders, consistent regulations become paramount to cost efficiency. This is a common occurrence in the growing global economy.

Jan 1, 2010

By Art Frye, Lee Pratt, Gaichang Zhao, Greg Newman

This paper will discuss the Wight Pit wall slash at the Mount Polley open-pit copper-gold mine that scavenged a high grade block of ore from two double-benches of the pit wall. The Wight Pit orebody, discovered in 2003, is located in the Northeast of the property with the southeast pit wall approximately 50m (165ft) from the edge of Polley Lake. In early 2009, the Wight Pit was nearing completion while an estimated 150,000 tonnes (165,000 tons) of ore averaging a grade of 1.4% copper remained just inside the southeast pit wall. The ore block started 24m (78ft) above the pit floor and extended up another 48m (157ft) with a 70o plane defining the back of the block.

Jan 1, 2011

By Sanjay Sengar, Nabiullah Pingua, Saurabh Sahay

In India, more than 80 percent of the total of 557 million metric ton coal production comes from open-cast mines involving large overburden removal with average 1:3.5 stripping ratio which is going to in-crease in future. This operation consumes nearly 0.5 million metric ton explosives consisting of 80-85 percent bulk explosives and remaining 15 to 20 percent non-permitted large diameter explosives. Quali-ties of bulk explosives play an important role in rock blasting. Post blast results like poor fragmentation, tight mucking, toe problems, improper muck profile and lower productivity of mine may require chang-es in explosive loading factor (amount of explosive used per unit of rock blasted ). The explosive load-ing factor is an extremely important index to assess the economy of blasting operation.

Jan 1, 2014