Search Documents

By Oliver Bowles

In 1943 the Bureau of Mines began a review of trends in consumption and prices of the more important nonmetallic minerals. The first report covering building materials4/ appeared in December of that year. The present paper, which deals with chemical raw materials and fertilizers, is the second of the series. The 34 years from 1910 to 1943, for which statistics are presented herein, comprise periods of uneventful peace, unparalleled prosperity, industrial depression almost to the point of stagnation, and two wars of world proportions.

Jan 1, 1945

By W. R. ARGYLE, R. A. SHERMAN, Henry Kreisinger, John Blizard, B. J. CROSS, A. R. Mumford

On entering the World War the United States was confronted with the necessity of building in a short time a large number of ships of tonnage adequate to transport troops and war materials to Europe and to carry food supplies to the allied countries, whose merchant fleets had suffered greatly by submarine warfare. The necessity of building ships quickly led to the formation of the United States Shipping Board, which was charged with the duty of developing an efficient organization for the purpose. Such an organization was developed under the name of the Emergency Fleet Corporation; it was under the control of the Government, but could conduct its business in the most direct way, like a private corporation. In order to build the largest- number of ships possible without drawing too heavily on the steel industry, which was already taxed heavily by the production of munitions, it was decided to build wooden as well as steel ships. These ships were built from a few standard designs to enable a large number of duplicate parts to be fabricated in inland shops and transported by railroad to the shipyards on the seacoast, where they were assembled into ships. In other words, the plan was to manufacture the ships rather than to build them. The shops on the seacoast were reserved to make those parts of the ships' equipment that could not readily be transported. The inland shops made the parts that could be transported to the seacoast by railroad. Among the more important parts of the ships' equipment to be standardized were the boilers. As the Scotch marine boiler in large units is bulky and can not be transported by railroad, and as, for the same capacity,much more steelis needed in its construction than for water-tube boilers, a few simple designs of water-tube boilers were developed that inland shops having ordinary equipment could make in large quantities.

Jan 1, 1924

By F. W. Lee

This paper purposes to outline briefly results of seismic measurements made in the vicinity of blasts in a mine and in open-quarry operations. It endeavors to examine the amplitude and frequency of such vibrations as influenced by the loading, geology, and distance from the source and includes comments on factors that may index the destructiveness of a vibration and a method for measuring the stresses produced. There seems to be no simple mathematical analysis of the transmission of seismic energy through the ground, and experimental observations are at present most feasible. SEISMOLOGIC INSTRUMENTS Instruments developed by the Bureau of Mines for recording ground vibrations from quarry blasting comprise a new type of seismometer, oscillators, and a recording oscillograph. The seismometers respond to vibrations reaching them through the earth and transmit their characteristics by electric current to the oscilloglaph, where they are recorded by a beam of light on a moving strip of sensitized photographic paper. The seismometers are so constructed that their sensitivity to earth vibration can be controlled, thus keeping the amplitude of the recorded wave within bounds on the paper. Each instrument has been calibrated against vibrations of known intensity and frequency so that correction factors are known for the idiosyncracies of each unit. Moreover, each seismometer is calibrated in the field for its particular sensitivity setting at each blast. By these controls the actual movement of the earth due to vibrations of one ten-thousandth of an inch can be accurately measured.

Jan 1, 1936

By Larry R. Powell

As part of the Bureau of Mines effort to establish a comprehensive subsidence data base for subsidence technology development, subsidence and related data are being compiled for various mining, geological, and environmental situations. This publication presents data for a longwall mining operation in the Northern Appalachian Coal Region. Vertical displacements and relative faze positions are tabulated for 160 subsidence monuments. Measurements were taken 32 times during the 2 years it took to mine the two panels. Brief physiographic and geological descriptions of the mining site are presented along with a general account of the mining and subsidence monitoring methods.

Jan 1, 1981

By James F. Neill, O&apos

Brown iron ore resources in Barbour, Butler, Crenshaw, and Pike Counties were investigated in a drilling program and geological study by the Federal Bureau of Mines in cooperation with the Alabama Geological Survey and the University of Alabama. The aggregate footage drilled was 18,010 linear feet. When developed, reserves of 12,664,000 long tons of crude ore were indicated, containing from 26.9 to 29.0 percent iron and 0.2 to 1.6 percent manganese under a maximum overburden of 40 feet. Total inferred crude ore for the four counties was calculated to be 827,700,000 long tons. Beneficiation of samples by simulated log washing and use of a 118-inch screen yielded from 46.8 to 51.7 percent iron and 0.2 to 2.6 percent manganese. Screen-test studies indicated no appreciable interlocking between the iron and manganese minerals and the waste particles of materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size. While an indicated 2,198,000 dry long tons of usable iron ore can be recovered, sink-and-float tests show that it may be possible for 4,654,000 dry long tons to be recovered by other than log washing. However, applicable commercial processes have not been demonstrated.

Jan 1, 1965

By P. L. Michael

Several evaluations were made by Modified Rhyme Test (MRT) word lists transmitted through various simulations of the Trapped-Miner Communication System being developed by the U.S. Bureau of Mines. The tests were performed in a "single blind? situation so that the evaluators would not be biased by knowing the characteristics of the system being simulated. A computer program was developed to provide a simulation of the electrical aspects of the communication system and to provide an evaluation by calculation of the articulation index (AI). The study indicates that communication through the presently proposed system will be somewhat unreliable at depths as great as 300 metre even with the system operating at maximum effeciency.

Jan 1, 1977

By L. K. Weaver

Bureau of Mines investigated the progressive impact that petroleum (crude oil and condensate) operations in the Gulf of Mexico have had on onshore operations and the expected effect of increasing activities in this area on future petroleum supplies from domestic sources. The data analyzed include capital expenditures, number of wells drilled, success ratio for exploratory wells, daily production per completion, annual producing rates, and oil reserves. The report compares offshore and onshore data and ascertains trends in petroleum industry operations. Observed data and trends indicate that in the near future Gulf of Mexico development and production will continue to increase relative to total U.S. petroleum activity. By 1975 annual oil and condensate production from the Gulf of Mexico is expected to be in the range of 750 million bbl to 1,150 million bbl, and account for approximately 20 to 30 pct of the estimated total domestic production.

Jan 1, 1969

By F. W. Lee

This paper purposes to outline briefly results of seismic measurements made in the vicinity of blasts in a mine and in open-quarry operations. It endeavors to examine the amplitude and frequency of such vibrations as influenced by the loading, geology, and distance from the source and includes comments on factors that may index the destructiveness of a vibration and a method for measuring the stresses produced. There seems to be no simple mathematical analysis of the transmission of seismic energy through the ground, and experimental observations are at present most feasible. SEISMOLOGIC INSTRUMENTS Instruments developed by the Bureau of Mines for recording ground vibrations from quarry blasting comprise a new type of seismometer, oscillators, and a recording oscillograph. The seismometers respond to vibrations reaching them through the earth and transmit their characteristics by electric current to the oscillograph, where they are recorded by a beam of light on a moving strip of sensitized photographic paper. The seismometers are so constructed that their sensitivity to earth vibration can be controlled, thus keeping the amplitude of the recorded wave within bounds on the paper. Each instrument has been calibrated against vibrations of known intensity and frequency so that correction factors are known for the idiosyncracies of each unit. Moreover, each seismometer is calibrated in the field for its particular sensitivity setting at each blast. By these controls the actual movement of the earth due to vibrations of one ten-thousandth of an inch can be accurately measured.

Jan 1, 1936

By Michael Horn

[An economic trading region made up of 22 eastern Washington, northern Idaho, and western Montana counties, with Spokane, Washington as the central place, was defined for this study. modeling system with the, 1985 county database was to create an Input/Output based model of the regional economy. The leading ice, with respect to income, employment, value of exports, and total industry output are shown for each county and the region. The value of total industry output from natural resource based industries is also shown for each county and the region. Interindustry transactions, final demand, and value added components for the region are shown in the Regional Gross Flows Table. The total gross output for the region is valued at $36.7 billion. Total industry output for the region is $18.1 billion. The region provides $5.4 billion in income to a work force of 286,000. Spokane County, Washington accounts for about 50 percent of the regional total industry output, income, and employment. Both Spokane County and then as a whole produce about 80 percent of the total industry output for final demand with remaining 20 percent going to intermediate inputs for further production. Spokane County exports about 43 percent of its total output while 35 of the regional output is exported. Exports account for more 50 percent of the total in 18 of the 22 counties within the region. About 9 percent of the total industry output from Spokane County and 19 of the total output from resource f: .t *III For counties Spokane a industry ? N from nafural resource based represents 18 percent ?.{1 to 71 s. ?-{ and averages 39 r. ?-11 of total county +' ' 7:. FS.-f.?) If t. Natural resource it us -t for more than 50 coutny 1 s ? sass in seven counties within region.]

Jan 1, 1992

By J. P. Morris

The Bureau of Mines investigated the mechanics of fuming of iron-carbon melts during top-blowing with oxygen. Melts weighing 45 lb were prepared in an induction furnace and blown with oxygen by means of water-cooled lances. The rate of fuming was measured and correlated with the operating variables. The data showed that the primary cause of fuming was a boil at the bath surface in the impingement zone of the oxygen jet. Nucleation of the carbon monoxide bubbles producing the boil was apparently brought about by the precipitation of an oxide phase. The actual fuming mechanism involved partial oxidation and vaporization of bubble films and fine metal spray generated by the bursting of the bubbles. Bubbles that formed outside the impingement zone produced little fume. The distribution of trace elements between the metal and fume strongly indicated that the fume contained fine spray particles as well as particles that had condensed from vapor. The rate of fuming was found to be proportional to the carbon content of the metal) the concentration of oxygen in the jet) and the bath temperature) provided that a continuous boil occurred. In the absence of a boil) very little fume was produced.

Jan 1, 1967

The investigation summarized in this report addressed two primary issues: the determination and use of correction factors, and the development of guidelines for velocity measurement site selection. Other ancillary issues which were addressed include a comparison of measurement methods and devices, aircourse cross-sectional area measurement, and characteristics of mine airways. An exhaustive literature search and analysis was performed; extensive in-mine experiments were conducted; a quantitative analysis of the data was used to develop correction factor tables and site selection guidelines. The reported results of other researchers who have examined the correction factors and site selection criteria, were analyzed in light of the results of this study. The measurement devices included in the experimental phase were: vane anemometer, vortex shedding anemometer, a prototype thermoanemometer, smoke tube, and, oil of wintergreen. The measurement methods include single-point centerline, timed¬-point traverse, continuous traverse for the anemometers, and various distances and cloud positions for the smoke tube and oil of wintergreen devices.

Jan 1, 1983

By W. P. Yant

[This report describes results of a study bf the carbon monoxide and particulate matter in the air of the Holland Tunnel and metropolitan New York made by the Bureau of Mines (which had participated in the development]

Jan 1, 1941

By Wm. O. Vanderburg

This report on the mining and milling of tungsten ores is the second part of a general study of the domestic tungsten industry. The first part, comprising general information on tungsten, has been printed as Bureau of Mines Information Circular 6821. The purpose of these papers is to increase efficiency in the mining, preparation, and utilization of the tungsten resources of the United States. The tungsten industry forms so small a part of the vast mining and metallurgical operations of the illation that private metallurgists have not had enough inducement to give special attention to the recovery of tungsten minerals from the ores, and many of the small companies are financially unable to undertake research work. A study of the milling of tungsten ores reveals that further improvement is possible, especially in the treatment of slimes. Recent experimental work by the Bureau shows that the flotation process is applicable to certain tungsten ores. The future of the tungsten industry it the United States depends to a great extent on utilization of the low-grade deposits of the contact-metamorphic type.

Jan 1, 1935

By J. B. Cunningham

Lithium in the form of metal, salts, and alloys is particularly important because of increasing industrial uses resulting partly from wartime developments. Lithium carbonate and lithium strontium nitrate, which impart a brilliant red color to a flame, are used in pyrotechnics. Lithium chloride and fluoride are used in fluxes for welding aluminum to dissolve the oxide coating on the aluminum and prevent oxidation of the molten metal. Lithium carbonate is used in ceramics in raw alkaline glazes because of its unusual fluxing properties. The use of 9 to 12 percent lithium carbonate permits a marked increase in the amounts of alumina, calcium, and silica that may be Used and results in a more stable glaze with sufficient alkalinity to produce vivid copper blues and other typically alkaline colors. Lithium stearate is used as a grease in airplane engines because of its ability to withstand wide changes in temperature. In view of its great affinity for nitrogen, hydrogen, oxygen, sulfur, phosphorus, carbon, and silicon, lithium has an excellent scavenging action on molten metals. It forms stable nonmetallic compounds of low specific gravity or gases that are eliminated at pouring temperatures. Lithium is generally added to the melt in the form of a lithium-calcium alloy consisting of 50 percent of each ingredient or as an alloy of 98 percent copper and 2 percent lithium. The lithium-calcium alloy added to cast iron before pouring, acts as a scavenger and increases the fluidity of the melt. This alloy also is said to increase the corrosion-resistant properties of stainless steel alloys and to improve their polishing qualities.

Jan 1, 1948

By E. R. Spencer, E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. In response, researchers at the National Institute for Occupational Safety and Health (NIOSH) have been conducting a cross-sectional survey of equip­ment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by dredging. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to iden­tify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges used in several surface mine sand and gravel operations and in the processing facilities. Results indicate that there are areas on the dredges (crane, suction pumps and diesel engines) where sound levels greater than 90 dB(A) are pres­ent. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration’s (MSHA’s) permissible exposure level (PEL) of 90 dB(A) eight-hour time-weighted average (TWA8), laborers, mechanics, oilers, helpers, pickers and greasers are the workers most likely to be exposed to hazardous sound levels and to thus develop NIHL over time

By Roy T. Sorensen

As part of its mission to maintain an adequate supply of minerals to meet national needs and maximize mineral production from domestic sources, the Bureau of Mines is investigating the recovery of alumina by hydrochloric acid leaching of kaolinitic clay. Most iron impurities are leached from the clay along with the alumina and must be removed before or during crystallization to aluminum chloride hexahydrate. The thermal decomposition step then provides an alumina product of acceptable iron analysis. Miniplant studies of a Bureau-developed solvent extraction technique, using a tertiary amine in kerosene diluent, have demonstrated that the iron content in aluminum chloride leach liquors can be reduced to levels of less than 0.007 wt-pct (7 ppm), expressed as Fe203. Entrained and dissolved organic matter in the purified pregnant leach liquor from the solvent extraction circuit can be reduced to less than 2 ppm by using a fabric-packed coalescer and subsequent activated carbon treatment. Investigators discovered that a steady buildup of zinc accumulated in the solvent phase within the extraction circuit, proportional to the amount of leach liquor treated. The solvent phase zinc analysis increased by 0.01 wt-pct ZnO for each 1,000 gal of pregnant leach liquor purified.

Jan 1, 1981

Develop a new technique of in situ rock stress measurement which can be used when and where the conventional methods, such as the overcoring stress relief methods and the hydrofracturing method, cannot be effectively applied. Approach The Bureau of Mines developed basic principles to determine existing biaxial stresses in rock mass by using an instrumentation package consisting of one 3.8-cm-diameter hydraulic cylindrical pressure cell (CPC) and two 5.7-cm-diameter cement-capsulated flat hydraulic borehole pressure cells (BPC) to he installed in a single drill hole.

Jan 1, 1988

By R. H. Thompson

Preliminary safe distances for blasting wiring from typical electromagnetic sources are presented. The distances are for underground coal mines and electromagnetic sources in the frequency range below 10 MHz. The distances are based on measurements performed at 3 locations in each of 3 coal mines. The measurement apparatus, measurement procedure, measurement results and the rationale used in the calculation of the safe distances are all described. The safe distances presented are dependent on the measurement results and their interpretation. More measurements are clearly necessary to establish the validity of the suggested distances.

Jan 1, 1985

By J. O. Lewis, Carl H. Beal

The material for this paper was collected for the most part by C. H. Beal during the years 1916, 1917, and 1918. Many of the conclusions reached in regard to the life of oil wells have already been published by the Bureau of Mines 1 but those presented in this paper deal particularly with the theoretical aspects of oil production. The report discusses some of the fundamental factors governing oil production, taking up first the conditions affecting the. amount of oil in the oil sand, then those factors that control the rate of production of oil wells, and then discusses several related problems, most of which deal particularly with the effect of the production of one well on that of another.

Jan 1, 1921

By Paul M. Hall

In the last several years, the coal mining industry has made significant changes in the design of longwall mining systems to make them more productive. Some changes, such as increasing the length of the coal faces and increasing the capacity of the face conveyors, have resulted in problems with achieving sufficient motor torque to start and operate the longwall face conveyors. Other changes, such as increasing the size and/or decreasing the percent impedance of longwall power center transformers, have resulted in problems with the short-circuit currents on the transformer secondaries exceeding the interrupting ratings of the molded case circuit breakers used to protect the secondary circuits. A survey of 24 longwall mining systems in northern West Virginia was conducted to investigate both problems. The results of the survey are presented and analyzed. Several recommended solutions to the problems are presented to enable the coal mining industry to design safe and productive longwall mining systems.

Jan 1, 1982