Search Documents

Studies of coal reserves have shown that the total augerable reserve base for the United States is estimated to be five billion tons under the current state of mining technology; the potential reserve base at 850-ft penetration is estimated at 20 billion tons. It is with the idea of improving coal recovery, a basic objective of Project Independence, that new concepts, such as modifications and improvements in current machines and development of ways to recover pillars left by current augering, are required. Unless recovery is improved, these potential reserves amount to lost coal.

Jan 1, 1975

By Robert L. Lagace

This final report documents the work done by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC), on Contract H0122026 (which began in August of 1971). Under this contract ADL provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau's programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of independent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau's contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Commun¬ications," and Volume II, "Seismic Detection and Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume.

Jan 1, 1974

By L. C. IlsLey

Many accidents rightly classifiable as electrically caused are not so classified for the reason that in numerous accidents the part that electricity played in causing the fatality is only suspected. For instance, a workman might receive a shock that would cause him to lose his balance and fall beneath a trip of cars; if no one saw the first part of the accident, the cause undoubtedly would be charged to "haulage." This paper covers a brief study of fatal and nonfatal electrical accidents. The first usually result from direct contact with the electrical circuit or electrical apparatus; the second more often are the result of arcing or flashing due to handling defective apparatus or making repairs on "live" equipment or circuits. It is hoped that helpful suggestions may be offered for minimizing accidents of these two classes.

Jan 1, 1938

By John D. Warne

"INTRODUCTION Initiated as a part of the Bureau of Mines program for development of strategic minerals for national defense, Investigation of the fluorspar deposits of the Northgate area was begun in June 1944 and completed in March l946. Mining Operations were active in the district during most of the period of investigation.The Fluorspar, Fluorine, and Camp Creek mines develop the two more promising vein systems known in the area, the Fluorspar group of claims covering one vein system and the Fluorine and Camp Creek groups the other. Figure 1 shows the location of the properties. The Fluorspar and Fluorine properties were operated (except during the winter months) by the Western Fluorspar Corp. The Camp Creek mine was operated during 1943 and 1944 by Kramer Mines, Inc.The properties were examined April 20 and again November 4 to 12, 1943, by C. R. Wilfley, a Bureau of Mines engineer, who recommended work to determine ore reserves and to serve as a guide for development. Investigations by the Bureau of Mines covered all three properties."

Aug 1, 1947

By R. Vernon Helm

Four tables listing values for the various physical properties of those sulfur compounds most likely to occur in petroleum and petroleum products are given herein. The data necessary to bring the first compilation2/ in this subject up to date are given in table I -Revised and Additional Data, which includes boiling points, refractive indices, densities, and freezing points. Tables 11-, III, and IV are published for the first time and include refractive indices for the F, C, and G' lines of hydrogen and the helium D:3 line; surface tensions and viscosities, and refractivity intercepts, specific dispersions, specific refractions, and parachors. The need for information concerning the sulfur compounds in petroleum is becoming-more urgent because of the necessity of refining larger quantities of high-sulfur crude oil to meet the rising demand for petroleum products. For a number of years the Bureau of Mines has been engaged in research to make available more information concerning the properties of the sulfur compounds in petroleum. The petroleum industry has recognized the value of such studies, and as a result the American Petroleum Institute has established Research Project 48A to study sulfur compounds. The investigations under this Project are to be done in Bureau of Mines laboratories as a cooperative project in connection with the work already started.

Jan 1, 1949

By Harvey L. Pastan

The purpose of the investigation and analysis described in this report is to assess the data flow requirements that are required for remote supervisory control of a continuous mining system. Since these control concepts as applied to continuous underground mining are still in a formative stage at the present time during the first half of 1975, assumptions had to be made based upon engineering judgment as to what embodiment of mining machinery and control methodology seemed most feasible for achieving such a system. Based upon these assumptions and estimates of the control system's accuracy and response requirements, it was then possible to estimate the communication requirements for the assumed system configuration. 2. Approach The team members responsible for this study visited numerous coal mines to observe room and pillar mining operations in both high and low coal. The objective was to observe the methods of operating a variety of continuous mining machinery and haulage equipment with a view toward defining the problems to be overcome in the application of automation to the coal extraction process. Descriptive information concerning the mining equipment was obtained through contacts with the manufacturers. Conferences with Bureau of Mines personnel, equipment manufacturers and developers, and mine operators were held to explore the current thinking and developments being pursued toward automation and increasing both production and productivity.

Jan 1, 1975

By James C. Barker

The U. S. Bureau of Mines made a reconnaissance In the western Crazy Mountains for cobalt and associated metals as part of the Alaska-wide critical and strategic metals program. The area, located about 75 miles north of Fairbanks in central Alaska, is underlain by complexly faulted, predominantly clastic sedimentary rocks bordering the Tintina Fault system. Above background metal concentrations were found to occur in altered fault zones, tectonic breccias, soils, and ground water seeps and precipitates that either cut or are derived from the faulted clastic sedimentary rocks. Up to 0.115 pct cobalt and more than 2.0 pct zinc were detected in soil samples. Spring precipitates contained up to 1.3 pct zinc, 0.037 pct tungsten, and other metals. Some localities lacked cobalt but contained anomalous amounts of copper, lead, zinc, silver, and other metals. No outcropping of primary metallic minerals was located because of Colluvium and vegetation cover and extensive deep leaching. Therefore, whether the metal values encountered are due to primary deposits with economic development potential or are the results of concentration by ground water from low-grade sources is unknown. The presence of cobalt, nickel and zinc, and the identification of minor tin and tungsten indicate that further investigation is warranted.

Jan 1, 1983

By Martin Smirlock

A novel instrumentation system has been developed which enables simple, quick, and accurate measurement of vehicular dynamics within low speed ranges. The system, consisting of a microwave transceiver and microprocessor data acquisition and reduction system, measures the deceleration dynamics of low-speed mining and construction equipment. It makes the basic measurement, calculates key parameters such as average deceleration, initial velocity, stopping distance, and brake system delay time, and produces autoscaled graphs of velocity, acceleration, and displacement versus time.

Jan 1, 1981

By John A. Johnson

"INTRODUCTION The use of wet drilling with adequate ventilation has largely controlled production of dust in drilling rock; however, in some operations, such as shaft sinking and modern tunnel driving, when each of a number of drills is operating in a small cross-sectional area, it is at times difficult to ventilate well enough to keep the dust concentration within desired limits.Some chemical compounds, known as wetting agents, when added to water in small quantities reduce the interfacial tension and make it possible for the solution to wet dust particles more effectively than water alone.This report presents results of tests on the effectiveness of two wetting solutions in reducing the amount of dust produced by wet drilling in basalt.ACKNOWLEDGMENTSThe tests were conducted the Bureau's Mount 'Weather Testing Adit,Mount Weather, The author acknowledges the assistance and cooperation of Wing G. Agnew, superintendent; Marvin M. Revelle, mining-engineering aide; and the rest of the crew at Mount Weather in conducting the tests. C. W. Owings, mining engineer, Safety Division, assisted in conducting some of the first tests and gavel valuable advice and guidance throughout the work and in preparing this report."

Jan 1, 1943

Comparative tests of four coals used industrially for coke production have been made by three laboratories of the Federal Bureau of Mines, each using its standard equipment and procedures for evaluating coal for coking. Two of the coals were blends used in the western and eastern sections of the United States, the third was a strongly coking coal widely used for producing coke in Alabama, and the fourth was a blend typical of those used for producing foundry coke in the Birmingham district. The coals used and the cokes produced from them covered a wide range of chemical and physical properties. The tests used at all three laboratories for determining the physical properties of the cokes were made according to ASTM (American Society for Testing Materials) methods. The excellent agreement found for the physical properties of the cokes indicated that, for the coals tested, the BM-AGA (Bureau of Mines-American Gas Association) 18-inch circular retort used at Pittsburgh, Pa" the 14-inch slot-type oven used at Denver, Colo., and the 17-inch slot-type oven used at Tuscaloosa, Ala., were substantially equivalent for evaluating coals for production of coke. Thus, added value is given to data obtained previously and independently at these three Bureau laboratories. INTRODUCTION Laboratory equipment to produce coke for evaluation has not been standardized by the industry. The results obtained with anyone design of equipment have been regarded as showing only the relative values of coal to produce coke of the requisite quality. Few systematic studies have been made to correlate results obtained in different types of equipment. Results of one, in which the Bureau of Mines participated, were published recently.2/ This

Jan 1, 1961

By William J. Kemnitzer

This study was made to show the growth of petroleum coking and to determine trends and characteristics of marketing and utilization of coke on the West Coast, comparing these data with those of the United States as a whole. An earlier Bureau of Mines economic survey of petroleum coke was made in 1930 before the widespread use of coking processes. Data, derived from published and unpublished literature as well as from interviews with industry representatives, show a marked increase in the production of petroleum coke since the end of World War II. This increase resulted from the need of refiners to upgrade heavy residuums for which the demand was diminishing. Increasing coke production as well as significant market shifts away from California-produced coke have created excessive stocks of petroleum coke on the West Coast. The causes of these market shifts were based mainly on (1) economic factors and (2) certain undesirable qualities of some of the petroleum coke produced in California.

Jan 1, 1965

By David Oyler, Craig Compton

The The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL) is continuing to investigate the behavior of fully grouted roof bolts in the weak roof rock of the Safety Research Coal Mine (SRCM). This paper describes the results of three studies: • A series of 24 pull tests of bolts installed fully grouted and overcored to leave 12 inches of grouted bolt. The tests compared the pull-out performance of offset-head roof bolts with that of standard 5/8-inch bolts; • A second series of 24 tests that compared the pull-out loads obtained by bolts installed with 1 ft of resin (a Short Encapsulation Pull Test or SEPT) to that of fully grouted bolts overcored to leave only 12 inches of grouted bolt, and; • An investigation into the pressures generated during the installation of fully grouted resin bolts. All of the bolts installed and pulled were overcored and removed from the roof after the pull tests to allow inspection of the resin. The first study found that there was no significant difference in pullout load between the offset-head bolts and the standard bolts. The second study, comparing the SEPT bolts and the partially-overcored fully grouted bolts, indicated that SEPT can significantly underestimate bolt anchorage grip factor, suggesting that the SEPT is a conservative measure of actual bolt performance. Significant loss of resin to cracks in the roof was observed in the bolts overcored in the SRCM. The third study explored one possible explanation for the resin loss, high pressures generated during bolt installation. These tests employed bolts installed in strain gauged steel tubes. The results confirmed that significant pressures (greater than 4,000 psi) can be generated during bolt installation. The results of the pressure tests, combined with the observations of resin loss in bolts installed in the SRCM, suggest that under some circumstances resin loss and under-encapsulation could take place and lead to degraded bolt performance. Glove fingering was observed in all recovered bolts to various degrees. The limited comparative data suggested that the effect of glove fingering ranged from slight to moderate. Complete mixing of the resin was observed on all of the 40 bolts recovered (28 fully grouted and 12 SEPT). Australian and U.S. resins were compared and the Australian resins were observed to have much smaller catalyst compartment areas and lower resin viscosities. These differences are suggested as potential explanations for occasional resin mixing problems noted in Australian resin bolt installations.

The objective of this condensed handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface coal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. It will be carried with the inspectors during their surveys. The complete handbook should be left in their offices except for Appendix II which lists the compositions of products found in previous surveys. There are several portions of the condensed handbook which should prove most useful to the inspectors. The names and locations of these portions are listed below: Procedure for an Industrial Hygiene Survey (Page 2-1) Survey Check List (Page 2-3) Rules for Determining if Sampling is Required (Page 2-2) List of Most Frequently Encountered Contaminants (Page 2-5) List of Candidate Contaminants and their Sampling Conditions (Page 2-A) Interpretation of Results (Page 3-8) For obtaining information not available from the above mentioned portions of the handbook, the inspector is directed to the Table of Contents, and the Glossary of Terms (Appendix I).

Jan 1, 1975

By Robert Stefanko

The growing demand for energy during the post World War I and World War II periods has prompted underground coal production to increase rapidly. This has been met primarily by mine mechanization, resulting in the development and application of new mining machine types. Correspondingly, the total connected horsepower of each machine as well as the number employed has enlarged rapidly since 1950. (2,3,9,14,16,17) Electrical consumption for each mine has also grown. In the early years of mining electrical applications, only d-c power was utilized underground. Yet, d-c machine limitations were soon realized, and many a-c systems were substituted to permit economic and efficient utilization of a-c distribution and motors. Due to the attractive torque characteristics, ease of distribution and speed control, several traction applications have continued to be powered by d-c motors. The result has been the now prevalent use of mixed a-c/d-c mine power. However, augmented electrical power employment seems to have added to underground coal mining electrical accidents.

Jan 1, 1974

By J. C. Kerkering, S. M. Miller, P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown's modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers' Z, measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 1993

By George W. Toth

Uranium in situ leach mining has recently emerged as a viable alternative to conventional miring techniques. The cost implications of in situ mining are therefore of increasing interest to mining paracticioners as well as public officials. This report presents the results of an assessment of uranium in situ leach mining costs through the application of process engineering and discounted cash flow analysis procedures. A computerized wasting technique, termed a cost model, was developed through this effort to facilitate rapid cost analyses. Application of this cost model will generate mine life capital and operating costs as well as solve for economic production cost/lb. U308. Conversely rate of return may be determined subject to a known selling price. The data bases of the cost made! have been designed to reflect variations in Texas vs. Wyoming site applications. The results If applying the model under numerous ore deposit, operating, wellfield and extraction plant conditions for Texas and Wyoming are summarized in the report. Sensitivity analysis of changes in key project parameters have also been tested and reported.

Jan 1, 1981

By S. J. Rodgers

This report presents the results of in-mine studies to determine the severity of dust sources in conventional mining operations. Three underground coal mines were surveyed using gravimetric samplers and GCA RAM-1 continuous dust monitors. Two additional mines were surveyed using only GCA RAM-1 monitors. Data on dust control methods were acquired during the survey, also. The results indicated that cutting/drilling and loading out were the dustiest operations during a conventional mining cycle. Roof bolting, shot firing and product transport were less severe dust sources.

Jan 1, 1983

To alleviate the hazard to personnel and danger to equipment caused by fires on large, mobile vehicles. The Approach: A system which automatically senses a fire at its early stage of development, warns the driver of the danger, and activates fire extinguishers in the zone of combustion, How It Works: The automatic fire protection system utilizes both thermal and optical sensors to detect the heat or light given off by a fire in the area of concern (Fig. 1). The system warns the driver of the hazard and then automatically extinguishes the fire with pressurized S-C class powder. The system can also be activated manually from the operator's cab or from ground level. Further, the automatic sequencing of the system can be manually overridden by the driver if he determines that the fire sensors have malfunctioned to cause a false alarm.

Jan 1, 1974

By J. H. East

"INTRODUCTION .Very little information regarding coal mining in Spain has been published in the American technical press, and few people realize the extent of this industry or the conditions under which coal is mined. The information in this publication was collected in 1945 and consists of personal observations in Spain, statistics, and other data of a, general nature obtained from official sources.Spain produces bituminous coal, lignite and anthracite, but the total tonnage mined is less than the national requirements. Before the war, an appreciable tonnages coal was imported from Great Britain under the Anglo-Spanish treaty, which rebated import duties and effectually prevented competition from any other foreign source. The war stopped the major part of the important of British coal and caused rapid expansion of the domestic sources, but this was not sufficient to supply the industrial demand. Coal that formerly was not acceptable to industry because of quality is now mined and marketed. The Government, allocates the better-grade bituininous coal to the various industries in accordance with the national importance of the work in which they are engaged; for example, the railroads are allotted 100 percent of their requirements, but cement companies can obtain only 25 percent.The Government offered to inducements to increase the production of coal of any class, but the larger part of the increased tonnage obtained was in inferior grades; as a result, the lignite production was taxed, while a bonus was paid for bituminous-coal production in excess of the 1942 tonnage.The anthracite and bituminous-coal areas were severely damaged during the Civil War and many experienced miners migrated to the lignite mines in eastern Spain. This has resulted in an acute shortage, particularly the Province of Oviedo where the most important bituminous-coal deposits are located."

Jan 1, 1947

By Robert L. Lappi

Eight interburden handling concepts are developed for multiple seam area mine stripping operations in central and western United States. They are based on data gathered and analyzed during field surveys, literature reviews and visits to state requlatory agencies in five states. It is concluded that improvement of reclamation practices through selective interburden handling techniques is possible at lower operating costs than currently incurred. Specific multiple seam mining systems are discussed in this report.

Jan 1, 1980