Search Documents

By J. Mitchell Linne

The principal mineral commodity in the Orleans Mountain RARE II area (No. 35019) is gold. Gravel deposits along the Salmon River contain placer gold. Lode gold with associated silver is contained in quartz veins. Many placer mining claims have been located within the study area in the Salmon River district. Four placer patents totalling 230 acres were issued for claims on the Salmon River between Lewis Creek and Forks of Salmon. On this same reach of river, adjoining and overlapping the study area boundary, approximately 3.3 million cu yd (2.5 million cu m) of gold bearing gravel with values ranging from $0.51 to nearly $5 per cu yd (50.66 to $6.50 per cu m) (gold valued at $400 per troy oz), are contained in three placers, the Bloomer, Pot Luck, and Horn (table 1). Within the study area boundary there are approximately 950,000 cu yd (726,000 cu m) of gold bearing gravel in these three placers. These three mines yielded nearly 12,000 oz (373,000 g) of gold and more than 300 oz (25,000 g) of silver between 1872 and 1913.

Jan 1, 1982

By Donald James Butler

Problems resulting from underground mines in three inactive mining districts in Colorado were investigated. The purpose was to determine how these problems could be reduced or eliminated in new closings -- essentially by benefitting from lessons of the past. Mines in Leadville, Westcliffe and the Cripple Creek-Victor districts were evaluated. Two basic types of problems were found to exist in the districts: environmental degradation and hazardous conditions. Environmental problems result largely from acid and toxic drainage from the runes and from leaching of surface waste rock piles and mill tailings impoundment. The acid drainage contributes high levels of metals to streams and deposits sediment in the stream bottoms. Erosion of waste piles is a lesser problem. Hazardous conditions from open or improperly sealed mine shafts and adits, mine subsidence pits, and from deteriorating and unsafe surface structures are common to the three districts. These problems become worse with the ravages of time and vandalism. Engineering solutions which would correct or reduce many of these problems are presented. These recommendations should also be applied to new mine closures, however, more basic changes are needed to effectively implement improved mine closures. The changes must take place in the areas of legislation, mining practices and education. Legislated regulations should realistically reflect the needs of both the mine operators, protection of the environment and the best interest of the general public. Benefits should be provided for compliance with regulations instead of penalties being assessed for noncompliance. Hazardous conditions and environmental problems associated with mines can be alleviated through improved mine design and effective cloning procedures. Education should provide an appreciation by the general public of past and present problems facing mine operators. This will result in an improved mining climate which, in turn, will insure a continuing supply of minerals to meet increasing needs.

Jan 1, 1983

By Paul C. Hyndman

The U.S. Bureau of Mines investigations of the three subunits (fig. 1) of the Homestead RARE II area (No. 6291) revealed no evidence of mining activity or mineral deposits in the area. The Iron Dyke Mine, 3 mi (5 km) outside the study area produced ore between 1916 and early 1982 from a volcanogenic massive sulfide deposit in the Permian volcaniclastic Hunsaker Creek Formation of the Seven Devils Group. The Hunsaker Creek Formation does not crop out in the RARE II area, but extends into the area beneath Miocene flows of Columbia River Basalt. The abundant basalt in the area could be used as aggregate or dimension stone, but equivalent deposits exist closer to markets. INTRODUCTION Location and Access The Homestead RARE II area (fig. 1) encompasses 6260 net acres (253U ha), in three units, of the Wallowa-Whitman National Forest in Baker and Wallowa Counties, Oregon. Two small units of 160 and 300 acres (65 and 120 ha) are 5 mi (8 km) north and east of the main study area. Homestead, Oregon, on the Snake River, is about 3 mi (4 km) south of the two small areas, and about 3 mi (4 km) northeast of the main study area. Peripheral access is provided by State Highway 86, U.S. Forest Service Road 39, and ancillary roads and trails.

Jan 1, 1983

By J. W. Town

The Bureau of Mines determined the physical properties of southeastern Idaho phosphate fines as related to mineral composition, particle size and liberation, beneficiation, and potential use in structural clay products. The phosphate mineral in the fines was identified by unit-cell dimensions to be essentially the same as the phosphate mineral fluorapatite identified in the coarser sizes. The mean particle frequency as determined by electron-microscopy and pipet-analyses was between 0.5 and 0.2 micron. Liberation of the phosphate could not be definitely determined because of the weathered condition of the minerals and their extreme fineness. No beneficiation scheme was developed that would concentrate the phosphate into a marketable fertilizer product; therefore, forming and firing tests were made to demonstrate that the fines can be used to manufacture structural clay products.

Jan 1, 1968

By R. B. Schluter

Drying and preheating (partial induration) the green, unfired iron ore pellets is a means of reducing the energy required to produce metallized pellets. The Bureau of Mines processed three magnetite and two hematite concentrates through the unit operations of pelletizing, preheating in air, and reduction to metal to determine the effects of preheating upon the properties of the metallized pellets. The pellets were prepared in a 16-inch-diameter laboratory balling drum. Preheating and metallization were carried out in an externally heated 4-inch-ID by 4-inch-long stainless steel drum using air for the preheating atmosphere and lignite char as a reductant. The results 'varied considerably: two of the magnetites spalled when preheated in air at temperatures of 900° C and above, and the third magnetite and the hematite flotation concentrate required complete induration at 1,300° C to produce satisfactory pellets. The earthy hematite ore yielded excellent pellets at all preheat temperatures.

Jan 1, 1972

By Jon G. Bredeson

A survey of electromagnetic noise reports was performed and a summary of the results are given. Industrial concerns were surveyed for techniques to minimize the effects of electromagnetic noise and are presented. The common types of communication links used in mines today are presented. A mathematical development was presented which determines the probability of bit errors versus distance for various types of communication links designed for in mine use. The probability of undetected errors for the protocols of the communication links is given together with burst error detection.

Jan 1, 1981

By J. C. Gerdeen

SAP-S information on the following element types are included in this appendix: Type 1. Three-Dimensional Truss and Bolt Element Type 4. Two-Dimensional Finite Elements Type 8. Variable-Number-Nodes Thick Shell and Three-Dimensional Elements Type 9. Two-Dimensional Joint Element (to be used with Type 4 elements) Type 10. Three-Dimensional Joint Element (to be used with Type 8 elements) Additional SAP4 elements, Types 2, 3, 5, 6, 7 and 12, are also contained in SAP-S and information on these elements is readily available in any SAP4 user's manual. These elements are as follows: Type 2. Three-Dimensional Beam Elements Type 3. Plane- Stress Membrane I-r .n Elements Type 5. Three-Dimensional Solid Elements (8 Node: Brick) Type 6. Plate and Shell Elements (Quadrilateral) Type 7. Boundary Elements Type 12. Three-Dimensional Straight or Curved Pipe Elements

Jan 1, 1976

By George T. Faust

The petrographer engaged in examining the products resulting from the beneficiation of ores, and rock minerals is constantly required to develop new means acid methods of assaying microscopically the results of such operations. From time to time investigators have published descriptions of apparatus that have aided in solving problems in processes of physical separation. Thus, in 1919, Coghill and Bonardi 3/ published a paper covering the application of the binocular microscope and camera lucida to the microscopic analysis of pulverized ores. Similar work has been published by Schneiderhohn 4/ Schwartz 5/, and Head and his associates 6/, 7/, 8/. The present paper goes further and considers application of the polarizing comparison-microscope to problems directly concerned with mineral dressing where it is desirable to compare analogous products, and in addition it suggests new uses in various related fields. This work was conducted under the cooperative agreements of the Southern Experiment Station of the Federal Bureau of Mines and the University of Alabama.

Jan 1, 1940

By R. Ward Stahl

The underground junction or intersection is analogous to the doorway or window in a building in that the continuous wall or support for the overhead structure has been weakened by making the opening. Some type of bridge or support seems necessary to prevent roof sag and possibly eventual failure at this point, although frequently it appears that little is done until a fatal accident induces action. The intersection generally represents less than 15 percent of the exposed roof area. As a result of recent multiple fatalities, some of which occurred at or near intersections, the Bureau of Mines was asked to examine the junction-support problem more thoroughly and to report its findings. A national survey of the junction-support systems in use has been made by correspondence, and the local area has been canvassed rather thoroughly to determine just what and how much is being done.

Jan 1, 1962

To predict the spontaneous combustion potential of bituminous coals using a simple expression based on an easily acquired coal property. Background Approximately 20% of underground coal mine fires in the United States since 1978 have been attributed to spontaneous combustion. Spontaneous combustion fires in underground mines are most likely to occur in gob area; and are difficult to detect and to extinguish by direct fire fighting methods. Often, sections of the mine or the entire mine must be sealed for long periods, at a great economic loss to the mine operator, mine employees, and the surrounding community. It is conservatively estimated that the cost of scaling a large mine is about $50 million.

Jan 1, 1989

By S. P. Holt

The Salt Chuck mine is on the east bank of the Salt Chuck, a salt-water inlet at the head of Kasaan Bay, Prince Edward Island, Southeestern Alaska. The deposit was worked at intervals from 1905 until. 1941. Early ship-ments of hand-sorted ore are reported to have assayed about 4 percent copper, 0.15 ounce gold, and 0.15 ounce silver. The total mine production up to 1941 is reported to have been 326,000 tons containing 6,200,000 pounds of copper. During December 1942 the Bureau of Mines cut a 15-foot channel sample on the surface and channel samples from headings on the 300-foot level. In July 1943 a development project was started. Thirteen diamond-drill holes totaling 1,550 linear feet were drilled from underground stations on the 200- foot and 300-foot levels.

Jan 1, 1948

By Steven K. Ruggieri

This report describes the operation and maintenance of the Mobile Inert Gas Generator for use in the Remote Sealing System for fighting underground coal mine fires. Seals are emplaced in mine passageways between the fire zone and the rest of the mine isolating the fire zone from the mine. The seals consist of fly ash that has been pneumatically conveyed via inert gas through a borehole connecting the surface and the passageway, Inert gas is used as the fly ash seal transport medium (instead of fresh air) since the introduction of large volumes of fresh air in the vicinity of the fire zone would be undesirable. The inert gas generation equipment is mounted on two flatbed trailers, the "hot" trailer and the "cold" trailer. The hot trailer contains the combustion and cooling equipment. The cold trailer contains the moisture removal and compression equipment necessary to convey the fly ash. The system is self-sufficient and requires only fuel and fly ash deliveries. The Inert Gas Generator has been thoroughly performance tested and has been operated in the field for approximately 200 hr. The system was employed in the demonstration of the entire Remote Mine Sealing System at the Jenney Mine in the Fall of 1978. The system is currently available for fighting any future underground coal mine fires.

Jan 1, 1980

By Edward L. McHugh

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 5-acre Zwagg Island Wilderness Study Area (OR-12-14) in order to evaluate its identified mineral resources. The study area is located in Curry County, OR, immediately west of Brookings. There is no evidence of mining activity on or near Zwagg Island, and no mineral resources were identified. The steep-sided, flat-topped island is normally accessible from the mainland by way of a sandy beach. The island consists mainly of marine sandstone, mudstone, and conglomerate of the Jurassic Dothan Formation. Dothan Formation sandstone has been used locally as construction material. Rock along the coast has also been used for construction of jetties to improve harbor access; additional work has been proposed at the port of Brookings. Although suitable for other construction uses, stone from Zwagg Island would probably not meet physical requirements for jetty stone. Development of a stone resource on the island is unlikely.

Jan 1, 1987

By Richard H. Bares

One criterion central to most definitions of reclamation is the restoration of mined lands to their original productive potential. This is often difficult to achieve on mined lands in the Northern Great Plains because of the rigorous climate (Bares 19;2) and various soil related problems including sodicity, salinity, soil permeability, low organic matter and plant nutrient deficiencies (Malakondaiah and Safaya 1982). Field study sites were established on recontotured mined areas during the early 1970's (prior to the topsoil mandate) in which several amendments were tested for their ability to improve spoil/topsoil conditions and, hence, increase plant production. Physical and chemical properties of these control (untreated) and amended spoils and topsoils have been summarized (Safaya et al. 1982). A number of grass and legume species combinations were studied. The general effects of one time (prior to seeding), single rate (approximately 100 mT ha-1) application of leonardite and/or slack coal to spoils and topsoils was the reduction of grass dry matter yields (NB 1 test site: dry matter yield (DMY) without slack was 110 g m 2 yr I ; DMY with slack was 80 g m -2 yr 1 I and the promotion of legume establishment and yield (SB test site: DMY without leonardite was 13 g m 2 yr -1; DMY with leonardite was 93 g m 2 yr 1). On South Beulah topsoil, treated with leonardite, production of weedy species was remarkably lower than that without leonardite (SB test site: DMY without leonardite was 252 g m - yr -1; DMY with leonardite was 177 g m 2 yr 1). The general effect of commercial fertilizer applied one time prior to seeding (rates ranging from 9-13-0 to 44-1 12-28 kg ha-1 of N-P-K) was to increase plant production during the first two to three years after which the effect disappeared. This effect was much more pronounced on spoils (NB I test site: DMY on spoils without fertilizer was 53 g m -2 yr -1; DMY on spoils with fertiliser was 132 gm -2 yr -1). Weedy species accounted for most of the biomas, production during the first growing season. Three of the test sites were designed to study plant production on topsoils and spoils. Establishment and production of grass species were comparatively better on topsoils (30 cm in depth) than on spoils while legumes were most successful on the soils (Center test site, 1979; DMY of grasses on topsoil was 170 g m 2 yr -1 DMY of grasses on spoils was 52 g m -2 yr -1; DMY of legumes on topsoil was 20 g m -2 yr -1; DMY of legumes on spoil was 191 g m 2 yr -1). Total plant production on topsoiled (302 m thickness) plots at the South Beulah site (DMY in 1979 of 269 g m 2 yr 1) was comparable to that of native western wheatgrass prairie (DMY of 262 g m -2 yr -1). An experiment was conducted to find out if time of planting would have any effect on establishment of grasses on spoils. It was fund that late fall seeding was superior to spring planting for establishment of wheatgrasses at NB 3 test site (Control Plot, 1975: DMY on spring-seeded was 1 g m -2 yr - 1; DMY on fall-seeded was 55 g m -2 yr -1). In general, wheatgrasses (slender, streambank, thickspike and western) yielded the most aboveground biomass of all the grass species tested; yellow sweetclover was the most successful legume. Yellow sweetclover established and was productive on both spoils and topsoils but only where competition with grasses was apparently minimal. Durar hard fescue established and thrived on topsoil but dry matter production was low compared to that of wheatgrasses. Emerald crown-vetch demonstrated a potential for growth on spoils where water conditions were adequate, whereas side-oats grama, prairie sand-reed, alkali sacaton, and bird's -foot trefoil demonstrated only sporadic success. Little bluestem did not become established at any of the test sites. Peak production of the planted species, especially grasses, was generally reached by the second week of July. Legume and weed production continued to increase into late August.

Jan 1, 1982

The United States has not begun commercial operations to tap its largest poten-tial sources of oil supply - oil shale and coal. The reason is that domestic petrol-eum has been plentiful in the past and liquid products probably could be produced from it at the lowest cost. In view of the ever-increasing need for petroleum in the United States, the critical international situation threatening foreign supplies, the growing demands for steel, and the heavy costs to industry of constantly discovering and developing new oil fields, it is believed that the prompt development of a synthetic fuel industry based on oil shale and coal is not only requisite to safeguard our oil supply but is an economically sound course for the foreseeable future. To neglect its development is to close our eyes and minds to our own resources at a time when they are needed critically. It also is apparent now that neither the Government nor industry would be taking any considerable economic risk in starting the initial plants, especially as measured against their potential value in meeting critical oil and chemical demands and in building a new industry in the West.

Jan 1, 1951

By Larry L. Wischhoefer

The Automated Breathing Metabolic Simulator (ABMS) is a versatile machine capable of performing almost any physiologically appropriate respiratory simulation. The first ABMS was delivered to the Bureau of Mines by IBM in 1973. Since then efforts have been made to refine the systems and components which make up the ABMS including the Breathing Simulator Module (BSM), Gas Analysis Module (GAM), and Supervisory Controller (SC)-each of which are also capable of stand-alone operation. Since September 1980, Reimers Consultants has been testing and modifying the ABMS and its components in order to improve the equipment and to develop simulation criteria and parameters. Changes have been made to the Phase I Design Plan and Performance Specifications; future improvements based on current experience are recommended; and test results of full scale testing conducted by Reimers Consultants in November 1983 on several types of breathing apparatus are reported and illustrated.

Jan 1, 1984

By Edward W. Parsons

The transverse force developed by expansion-shell rock-bolt anchors on the wall of a drill hole as the bolt is tensioned was measured by the Bureau of Mines using a device specially designed and fabricated for attachment to a universal testing machine. Load cells equipped with electrical-resistance strain gages provided the data from which the transverse force, in pounds, was calculated. Seven different expansion-shell anchors were tested, and the ratio of transverse force to bolt-tension load was found to range between 0.98 and 1.94 to 1.0. The drag load appeared to be the major cause of the transverse-force variation, but the relative effects of individual factors that affected the ratio between the transverse force and the bolt tension were not determined.

Jan 1, 1968

By James W. Reil

A test series of small, precisely-controlled and thoroughly-monitored production blasts was conducted at two quarries. In each series, all variables except delay were kept constant, as much as practically possible. The first aim of the study was to determine the effect of local geology on ground vibration. The second aim was to test several hypotheses relating the effect of millisecond delay intervals to fragmentation and ground vibration. A resonant frequency of ground vibration was shown to be related to the thickness of the overburden, in accord with a model proposed by Gupta (1961). Since the overburden geology creating this resonant vibration cannot usually be changed, two methods were tested to choose delays such that blast vibrations would destructively interfere. These were shown to be effective in modifying both the peak particle velocity and response spectra of ground vibration. The delay interval chosen also affects fragmentation, primarily in massive rock, with an optimum relief between holes of 2 ms/ft. Strain gage records indicate a possible mechanism consistent with this information.

Jan 1, 1985

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. This volume deals with the development of a microcomputer based training cost model (TCM) which can be used to analyze training cost implications of various types of training. The model has been developed using Aston Tate's dBASE III plus language. The computer program and a test run of the model are presented in this report.

Jan 1, 1993

[RESULTS OF THE PRIMARY CONVENTIONAL PERFORMANCE AND COST MODEL OF THE UNIT OPERATIONS OF UNDERGROUND PERCUSSIVE DRILLING AND BLASTING]

Jan 1, 1977