Search Documents

By L. McWilliams, L. D. Patts, J. D. Noll, S. E. Mischler

Elemental carbon (EC) is currently used as a surrogate for diesel particulate matter (DPM) in underground mines since it can be accurately measured at low concentrations and diesels are the only source of submicrometer EC in underground mines. A disadvantage of using EC as a surrogate for DPM is that the fraction of EC in DPM is a function of various engine parameters and fuel formulations, etc. In order to evaluate how EC predicts DPM in the underground mining atmosphere, measurements of total carbon (TC; representing over 80% of the DPM) and EC were taken away from potential interferences in four underground metal/non-metal mines during actual production. In a controlled atmosphere, DPM mass, TC, and EC measurements were also collected while several different types of vehicles simulated production with and without different types of control technologies. When diesel particulate filters (DPFs) were not used, both studies showed that EC could be used to predict DPM mass or TC. The variability of the data started to increase at TC concentrations below 230, µg/m3 and was high (>+20%) at TC concentrations below 160 µg/m3, probably due to the problem with sampling organic carbon (OC) at these concentrations. It was also discovered that when certain DPFs were used, the relationship between DPM and EC changed at lower DPM concentrations.

By Charles Anema

The Mancarried and Helicopter Receivers were developed under the contract for trapped miner location. This program was a five phase program with 15 mancarried and 5 helicopter production receivers delivered under Phase IV and equipment documentation required under Phase V.

Jan 1, 1976

By J. D. Warne

The ferberite district of Boulder County, Colo., has been an important producer of tungsten since 1900. During World War I, high prices for tungston concontrates resulted in a brief period of intense activity, and the production in 1917 was 2,707 tons of 60 percent W03 concentrates. Production declined thereafter, and in 19.2 the tungsten produced in Boulder County represented about 4 percent of the Nation's output, being exceeded only by the scheelite production in California, Nevada, and Idaho. Boulder County has boon an important source: of tungsten in the Korean emergency; the present report does not describe this recent activity, as it will be covered by a future publication. Tungsten occurs in small ore shoots of narrow and irregular veins. Most of the ore shoots have been found outcropping on the surface. Core drilling; has been used by the larger operators to explore for new veins and to locate extensions of known veins.

Jan 1, 1953

By L. P. Purtell

The performance of ten anemometers of several types has been measured at low air speeds. Multiple calibration runs provided sufficient data for measuring random error about the mean calibration curve in addition to the difference between indicated and true speeds. Measurements were also performed of the minimum operating speeds of the anemometers.

Jan 1, 1979

By Carl L. Bieniewski

In a Bureau of Mines supply evaluation, the known uranium resources in the United States are estimated to have a total recoverable uranium oxide (U3O8) content of 3,132,400 tons at prices up to $69.32 per pound. Only those resources were evaluated for which sufficient quantity data are available and process technology exists for recovering uranium. A total of 160,800 tons of U3O8 is available at $8 per pound from ore deposits presently mined and an additional 244,700 tons available at prices up to $30 per pound from similar but usually lower grade deposits. A total of 2,726,900 tons of U3O8 is available from four other resources: copper leach solutions, wet-process phosphoric acid, Florida phosphate rock Leached zone, and Chattanooga Shale. These resources contain from 30,000 tons of recoverable U30, at a price of $7.52 per pound as a byproduct of copper leach solutions to 2,557,300 tons at a price of $69.32 per pound from Chattanooga Shale.

Jan 1, 1971

By Ronald B. Stotelmeyer

This report summarizes studies of 28 National Forest roadless areas in Montana completed by the U.S. Bureau of Mines (USBM) in the period 1974-1993. It also briefly describes 20 areas for which field studies have not been conducted. All 48 of these roadless areas have been recommended for addition to the National Wilderness Preservation System or proposed as special management areas by the U.S. Forest Service (USFS) or the Montana congressional delegation. The Bureau studies indicate which parts of the roadless areas have a high likelihood for mineral-resource development. They also show where mineral production has occurred in the past and where abandoned mine workings (possible hazards) would be encountered. The number of mine and prospect workings found are a measure not only of surface disturbance, but of areas not wilderness in character. For the purposes of this report, mine refers to a property which produced (or is currently producing) a mineral commodity, a prospect is a property which has been explored but has no record of production.

Jan 1, 1994

By K. O. Bennington

Cancrinite is one eonstituentof "red muds," a high-volume waste product of alumina production by the Bayer process. The Bureau of Mines determined the thermochemical properties of cancrinite as part of a program to provide such data for minerals of industrial importance. Cancrinite [Na7.68(A16Si6024)(N03)1.68 (H2O)4.1] was synthesized by reacting aluminum silicate gel with a solution of NaOH and NaN03, and the composition was determined by chemical analysis, differential scanning calorimetry, and thermogravimetric analysis. The heat of solution was determined by hydrofluoric acid solution calorimetry. The standard enthalpy of formation at 298.15 K, ?Hf°298, is ?Hf°298 = -3,487.97 ±2.6 kcal/mol, and the standard enthalpy of formation from the oxides and NaN03, ?H°298, is ?H°298 = -215.20 ±l.8 kcal/mol.

Jan 1, 1983

By R. Luhrman, E. Christ, B. Gores, S. Fischer, E. Johanning

North American railroad locomotive operators (engineers and conductors) are exposed to multi-axis vibration and shocks (1, 2). A recent epidemiological survey showed a prevalence of serious type of neck and lower back disorders nearly double that of a control group (3). Ergonomic working conditions are important co-factors in a vibration and shock exposure risk assessment (4, 5). The goal of this study is to illustrate typical work stations (cabs and seats) in US/Canadian type locomotives and assess shock related exposure risk by calculations of the new proposed shock risk indicators according to the new ISO 2631-5 (2004) (6). Methods Locomotive cab and seat inspections were conducted and operators’ activities were assessed by a trained observer. Field measurements (n=50) were obtained during normal revue service following generally accepted guidelines (ISO 2631 (1)). A sub-sample of n=20 locomotives were selected for the calculation of proposed shock indicators (ISO 2631 (5)). Results There has been little change in basic locomotive cab and seat design in the U.S.. Two locomotive cab design concepts are used: the Association of American Railroad (AAR) Control Stand and in newer series wide-body locomotives the “Control Consol” (Figures 1-2), with varying seating conditions, but frequently subjecting the operator to an awkward body posture in addition to the vibration and shock exposure. [ ]

Jan 6, 2006

The importance of controlling respirable dust and methane gas levels in underground coal mining cannot be underestimated. While respirable dust can significantly affect the occupational health of underground coal miners, methane gas accumulations pose significant safety concerns for these same workers. Water sprays and machine mounted dust scrubbers offer effective control of respirable dust exposures and methane gas accumulations. Water must not only be applied carefully to avoid dust rollback to the machine operator but must create sufficient turbulence to remove dead zones that could contain high concentrations of methane gas. While the flooded-bed dust scrubber has been generally responsible for decreased worker exposures to respirable dusts, this device has proved effective in controlling methane levels at the face. This paper reviews practical applications of water sprays and dust scrubbers to control respirable dust and methane gas on continuous miner faces.

By J. D. Dixon

This Bureau of Mines report describes the results of an investigation for developing and applying procedures for stabilizing excavations openings in highly yielding ground. The approach developed in this report involves nonlinear modeling of the progressive relaxation of the zones of rock mass around the excavations opening where Coulomb criterion of failure is exceeded. Stresses are calculated by using a computer code; Coulomb-failure condition is examined for both intact rock and joints (using strength parameters [~] and c). The rock mass in the failed zones is relaxed by reducing the Young's modulus of the rock based on an empirical formulation that is a function of the shape of the opening and the extent of the failed zone. In addition, the material in the failed zone is assigned reduced strength paramters 0' and c'. The limiting (or convergent) relaxed zone is obtained through an iterative process by manually changing the rock modulus and the strength parameters between iterations. Support pressures are computed by applying forces normal to the excavation surface. The approach is applied to the analysis of stability and support requirements for an entry in a longwall coal mine.

Jan 1, 1985

By Elaine T. Cullen, Thomas W. Camm

The mentor/learner model is a time-honored approach to teaching, including within the mining industry. Miners know when they see excellence and have a deep respect for experts in their field. By using expert miners as mentors to other, less-experienced miners, training programs can be developed that will have a legitimacy and credibility that resonates with those being trained. Building upon concepts in current theories of adult education, this paper highlights the unique advantages of using mentoring as a teaching method that can make the educational experience both interesting and effective. Current NIOSH safety training materials use these concepts to deliver effective adult learning experiences for workers in the mining industry.

Jan 1, 2002

By G. David Baskin

Changes in the 1978 quantity and value of the sales of various natural abrasives, compared with the data for 1977, were of a mixed nature. Output of tripoli-type materials and garnet increased in both tonnage and value. Emery production also increased. But special silica stone product sales decreased in both tonnage and value, and the reported quantity and value of sales of manufactured abrasive material also decreased for 1978. In 1979 output of tripoli-type materials and special silica stone products decreased in both tonnage and value when compared with the previous year. The tonnage and value of sales of garnet and manufactured abrasives increased when compared to 1978 data.

Jan 1, 1980

By C. S. Compton, D. R. Dolinar, D. C. Oyler

More than 80% of U.S. roof bolts are fully-grouted, but about 1500 roof falls are reported each year. Anchorage failure of a fully grouted bolt can occur when the roof is active near the top of the hole. This paper reports on an extensive series of short-encapsulation pull tests (in which the bolts are installed with only 1 ft of resin) that were conducted in the National Institute for Occupational Safety and Health (NIOSH) Mine Safety Research Laboratory and operating mines in WV and PA. The tests confirmed that poor anchorage can been countered under some weak rock conditions. Suggestions for improving anchorage are included.

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include better fire suppression systems, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By Gerald T. Homce, James C. Cawley

This paper updates an earlier report by the authors that studied electrical injuries from 1992 to 1998. The previous information is expanded and supplemented with fatal and nonfatal injury rates and trends through 2002. Injury numbers and rates were used to compare and trend electrical injury experience for various groups and categories. This information allowed identification of at-risk groups that could most benefit from effective electrical safety interventions. The data presented in this paper are derived from the U.S. Labor Department’s Bureau of Labor Statistics’ Census of Fatal Occupational Injuries (CFOI), Survey of Occupational Illnesses and Injuries (SOII) and Current Population Survey (CPS). Between 1992 and 2002, 3,378 workers died from on-the-job electrical injuries. Electricity remained the sixth leading cause of injury-related occupational death. From 1999 through 2002, 4.7% of all occupational deaths were caused by electricity, down from 5.2% in the 1992 to 1998 time period. The cause of death was listed as electrocution in 99.1% of fatal cases. Contact with overhead power lines was involved in 42% of all on-the-job electrical deaths. The construction industry accounted for 47% of all electrical deaths between 1992 and 2002, but showed overall improvement from 1995 through 2002 by reducing its electrical fatality rate from 2.2 to 1.5 per 100,000 workers. An additional 46,598 workers were nonfatally injured by electricity. Contact with electric current of machine, tool, appliance, or light fixture and contact with wiring, transformers, or other electrical components accounted for 36% and 34% of nonfatal electrical injuries, respectively. Contact with underground, buried power lines was involved with 1% of fatal injuries and 2% of nonfatal injuries. NIOSH research aimed at evaluating commercially available overhead power line proximity warning alarms is described. This research is expected to be the initial step for eventual development of a performance standard for such systems.

By McElroy. G. E.

"INTRODUCTION The ventilation of development faces in mines for diluting gas or dust concentrations and, in hot mines for providing air-motion cooling effect, by fan pipe units discharging high-velocity streams of air close to the face, is an important phase of mine ventilation. The effectiveness of such units depends largely on the air-flow distribution between the pipe discharge and the face, a subject on which little definite information is available. A study of the air flow from grills into rooms 3/ has provided some basic data, but under conditions no different from mine fan-pipe installations in development ends that the data are of doubtful application to mine installations, owing to differences in air-flow conditions.The purpose of this report is to present and discuss the results of an initial series of tests of a general investigation designed to yield definite laws and design data for the discharge of fan-pipe lines in mines. This series was planned to yield preliminary data on the effects of velocity of discharge, size and shape of pipe, and adjacent walls on the air-flow distribution. Tents were made on 10-inch pine with seven different end conditions and one change of wall condition. Changes in size and shape of discharge wore made by short transformation pieces directly at the discharge end, with the result that effects due to contraction and expansion of the flow, which proved to be of much greater importance than was expected, totally obscured any normal effects due to size and shape. The results of this series of tests, therefore, relate to 10-inch pipe with various discharge designs and are so reported."

Aug 1, 1940

By Elaine T. Cullen

Miners, like many skilled blue-collar workers, are not traditional learners. They have not generally been successful in classroom-type settings, preferring to learn on the job in a hands-on environment. U.S. miners are required to have annual safety training, but they rarely view this positively. In fact, it has been called “safety jail” by many of them, who regard it as a time to get a little extra sleep. The challenge then, was to find a way to develop effective safety training for these people, particularly in view of the fact that their work is among the most dangerous of all occupations. Miners are born story tellers. They share “near-miss” stories, stories about master miners they have known, and stories about how things used to be. These stories not only pass along information about what will happen if a miner fails to respect the mining environ-ment, they also instruct listeners in the culture of mining and the values it embraces. Stories, it seems, are a way to get safety messages to miners, especially inexperienced ones, and using older, wiser miners in these stories is an obvious choice. This paper will discuss how the training videos created to get safety messages to miners were developed, how “master miners” and story lines were chosen, and how the resulting videos have been received in the mining industry.

By Doss H. White

Alabama's non fuel mineral industry produced $560.6 million of mineral commodities in 1990. This was an increase of $99 million over the 1989 value and a new State record, a record achieved despite the slowdown in the national economy. This was the first year that Alabama's mineral value exceeded one-half of 1 billion dollars. The value of stone and cement, the two leading mineral commodities in terms of sales, increased $71 million over that reported for 1989 and was the primary reason for the new mineral value record. The State ranked 21st among the 50 States in total mineral value and contributed 1.68% of the total U.S. mineral value of $33.3 billion.

Jan 1, 1992

During development mining, ventilation capacity may decrease and the ventilation requirements may depart from initially planned values depending on the mining rate, increases in the methane emission rate, and changes in ventilation airway leakages. Insufficient ventilation air quantities and the occurrences of high methane liberation rates can overwhelm the existing quantity of ventilation air and result in elevated levels of methane gas during development mining. This condition can both limit the development of that section and increase the risk for an ignition that may lead to an explosion. Thus, the prediction of ventilation air requirements prior to mining can enhance worker safety by reducing the likelihood that explosive methane-air mixtures form. This study presents an approach for prediction of methane inflow rates using coalbed methane reservoir modeling. For this purpose, a two-phase coalbed reservoir model of a three-entry type roadway is developed. In the model, grids are dynamically controlled to simulate development of entries. Examples are given for methane inflow and ventilation air requirements as a function of mining rate, development section length, mining height, and the existence of degasification boreholes. This technology can be used to limit the methane concentrations occurring as a result of the influences of various coalbed and operational parameters.

Jan 1, 2008

The contractor examined L.T. White's Patent No. 3524680 and, finding it in need of engineering refinements, proceeded with a conceptual design of a variable wall mining machine. The contractor then proceeded to assess the feasibility of the variable wall mining machine measured against the criteria specified by the U.S. Bureau of Mines. The feasibility was judged from a physical aspect, a health and safety aspect, and an economic aspect. The Variable Wall Mining Machine was judged to be feasible on all three aspects provided that certain specified practices were adopted. Description The specifications and design and performance parameters of the Variable Wall Mining System as conceptualized are summarized in Tables I and II. The system consists of a side-cutting auger operating in a string of identical 12 ft. sections, along a 500 ft. retreating longwall face. In addition to the 41 identical sections, there is a special drive and discharge section at the head gate.

Jan 1, 2012