Search Documents

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 45 African jurisdictions. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; third, analysis of laws applicable to natural gas, petroleum, and related materials; and fourth, mention of laws regulating offshore operations. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of states or provinces, those areas are considered separately from the central government.

Jan 1, 1974

By M. W. Pullen

It is recognized that the determination of electrical resistivity of the earth within a given area may furnish information concerning the location of certain mineralized strata of economic importance. Present knowledge of the electrical resistivity of the various rock formations is almost nil, and the geophysicist who is detailed to make a survey of an area without any data as to the relative resistivity of the underlying rocks is greatly handicapped. Such surveys are usually made within areas known to contain mineral deposits to aid in locating desirable points for drilling. Usually these areas have been prospected by diamond drilling, and drill cores of the various rocks and ores are usually obtainable. Were it possible to make resistivity tests in a laboratory of the drill cores or from pieces of the rocks and ore within an area before attempting a field survey, this would indicate not only the advisability for such a survey but would aid considerably in the interpretation of the results of such a survey. To be of most value a definite method should be used for all such tests, and as yet such a method has not been established.

Jan 1, 1929

By George S. Rice

"INTRODUCTION During the past 4 or 5 years the frequent occurrence of bumps in coal mines of the Cumberland field, in Harlan County, Ky., and Wise County, Va., has caused much apprehension among miners and mining officials of that region.These bumps have caused many deaths and injuries, and have been increasing in frequency. Eight men were killed and a number injured by bumps in the first 4 months of 1934. Their unpredictable occurrence and the usual absence of any preliminary warning tremors or sounds, such as ordinarily precede a large fall of roof, cause fear of other bumps and impair the morale of mine workers.Acknowledgments This report on bumps in coal mines of the Cumberland coal field of Kentucky and Virginia is based on an investigation made at the urgent request of .the Harlan County Coal Operators Association, through James F. Bryson, director of safety of the association, to the Director of the United States Bureau of Mines, following a series of disastrous bumps in. Harlan County, Ky., and Wise County, Va. The request was granted and the writer detailed to undertake the investigation, which was made in June 1934.The officials of certain operating companies in the Cumberland field gave every facility for examining the conditions accompanying bumps in their mines. The writer is most grateful to them for the courtesies shown; to J. F. Bryson, to J. F. Davies, district engineer, Safety Division, U. S. Bureau of Mines, who accompanied the writer throughout his trip to the vari¬ous mines and gave him much assistance and detailed information regarding the occurrence of bumps; and to Dr. David White for reviewing the geological descriptions,Definition of Bumps ""Bumps"" are phenomena comparatively rare in the coal fields of the United States and, for that matter, in the coal fields of the world, because for their occurrence certain exceptional natural conditions are required strong, massive strata of sandstone or conglomerate above the coal and a fairly strong floor, as will be described in detail later."

Jan 1, 1935

By Frank T. Duda

A U.S. Bureau of Mines interactive FORTRAN computer program can screen explosion-proof enclosures intended for underground service. The program incorporates important information and criteria to assist enclosure manufacturers and Mine Safety and Health Administration (MSHA) personnel by providing a first-order approximation of rectangular explosion-proof enclosure characteristics prior to actual certification testing. The program uses information and data that can be retrieved automatically during program execution. The program also performs the calculations for a series solution algorithm and various equations to evaluate the enclosure for both a static internal pressure and an internal explosion. The program writes the intermediate and final calculations and information concerning the status of the screening process to a summary file on a floppy disk. One data base contains MSHA certification requirements given in the Code of Federal Regulations (30 CFR 18). A second data base contains material properties of acceptable construction materials and weld joint efficiencies. A series algorithm determines bolt and cover stresses for a simply supported rectangular cover with arbitrary bolt locations. Limit and yield line analysis is used to calculate the strength of body panels.

Jan 1, 1989

By W. P. Yang, L. B. Berger, G. W. Jones

"Any burning carbonaceous material, unless supplied with enough oxygen for complete combustion, will liberate carbon monoxide. Since tobacco in its many different forms consists largely of carbonaceous material, and duo to the conditions under which it is smoked (burned), carbon monoxide should be liberated. That this is true has been shown by Armstrong.***** who found that undiluted smoke from cigars contained in some tests more than 3.00 per cent carbon monoxide, the amount present depending upon the size and closeness of packing of the tobacco during manufacture and on the rate of burning.****** Cigarets gave much less CO, varying from 0.06 to 1.40 per cent. The rate of consumption and carbon content of the tobacco are not g.ven, so that a correlation of the values reported to conditions in closed spaces where people might be assembled are difficult, if not impossible.The Bureau of Mines is interested in the general question of carbon-monoxide hazards from tobacco smoke, mainly with regard to mine ventilation. In non-gaseous mines, especially metal mines, the question arises, whether, if groups of miners are permitted to smoke while working at unventilated faces or entries, would the accumulation of tobacco smoke in these places create an' additional hazards the to carbon-monoxide poisoning. The results should, in addition be of general interest in connection with ventilation of building and inclosed places where people may be assembled and smoking is permitted. The investigation described in this report was made with the above idea in view."

Oct 1, 1923

By Tom Retka

This three volume final report summarizes the activities and conclusions of this contract. The objective of the contract was to develop noise control modifications on a retrofit basis, for auger miner coal-cutting systems. Manuals were prepared to assist mine shop personnel in retrofitting the auger miner with these noise controls. Final Report Volume I - Details all vibration and acoustical tests conducted in development of the noise controls. Final Report Volume II - Noise Control Modification Manual for the Jeffrey 100-L Auger Miner describes the various noise control modifications to the auger miner, along with fabrication procedures, cost and vendor information. Final Report Volume III - Noise Control Modification Manual for the Jeffrey 94-l Bridge Conveyor describes the various noise control modifications to the bridge conveyor, along with fabrication procedures, cost and vendor information.

Jan 1, 1978

By H. W. Kilau

The Bureau of Mines evaluated synthetic fluorspars as substitutes for natural fluorspar in basic oxygen steelmaking using a high-temperature rotational viscometer and a quarter-ton basic oxygen furnace (BOF). Consider-able variation in stability and BOF slag fluidizing properties were found when using the initial synthetic products, but improved synthesis methods produced synthetic fluorspars that were generally comparable to natural fluorspar in laboratory testing. Trials in the furnace showed the synthetic products to be operationally the equivalent of natural fluorspar. Higher sulfur and phosphorus contents in some of the synthetic materials did not adversely affect the steel chemistry. Analyses of wet scrubber samples showed evidence that the pelletized synthetic fluorspars experienced greater physical and chemical disintegration than did natural fluorspar. It was also found that operation of a BOF without fluorspar is possible when making low-carbon steels because iron oxide is intrinsically generated as the slag fluidizer.

Jan 1, 1981

By Alexander E. Morrow

Oxygen breathing apparatus for use in mines was introduced to the United States in 1907. Despite their intended purpose of safeguarding lives, the apparatus led to the deaths of many men because of inherent or developed defects in the equipment, lack of training,, physical shortcomings of wearers, and improper procedures. The Bureau of Mines pioneered in research and training to curb logs of life among users of such apparatus and promoted development of safer equipment and procedures. As a consequence, deaths have been far less frequent. In 1944 the Bureau issued Information Circular 7279, Loss of Life Among Wearers of Oxygen Breathing Apparatus. That publication listed the case histories of 26 deaths that had occurred since the introduction of such equipment to American mining. The author, the late G. W. Grove,3/ asserted that further loss of life could be avoided if good equipment were used, teams were properly trained, and the basic principles of safe procedure were followed. This publication is a sequel to I.C. 7279 and contains information on eight deaths among wearers of oxygen breathing apparatus that were overlooked in the original compilation. It also describes the single death that occurred since I.C. 7279 was published.

Jan 1, 1959

By John C. Feeley

This paper is the result of a field study of prospect drilling in the Florida phosphate fields. The objective is to describe the drilling methods employed . . Since the general policies of the operating companies in the land - pebble area do not permit the dissemination of prospecting information and costs thereof , the writer has carefully avoided mentioning names and locations except by reference to existing publications ,

May 1, 1949

By Joseph J. Wallace

1. The investigation shows that there are 2 coal beds of major importance in Letcher County from the standpoint of present production - Upper Elkhorn No, 3 and Fire Clay - and 5 beds of minor importance - Whitesburg, Flag, Haddix, Elkhorn Leader, and Amburgy, The Upper Elkhorn No. 3 and Fire Clay beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,600 tons per acre-foot of coal in place, are estimated at 1,353 million short tons as of January 1, 1952. Of this total, 1,056 million short tons ere in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bad characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By K. E. Robinson

This study provides an initial indication that mill tailings produced in the Coeur d'Alene Mining District of Idaho can be placed on floodplain areas in a technically acceptable manner without artificial liners and without seriously contaminating the surrounding area. Tests have shown that landfills on these unused areas can result in returning these areas to productive use. The engineering properties of mill tailings permit construction of stable embankments. Designed slope protection inhibits water erosion. Among the environmental considerations in using tailings for landfill construction are the acid and other contamination produced by tailings and wind erosion of exposed tailings surfaces. The initial results indicate that adverse impacts are not as severe as previously thought, and mitigative measures are feasible. Based on the preliminary data, and in accord with existing Federal and State waste management regulations, a conceptual design has been developed for 23 potential landfill sites in the District, which could reclaim 750 acres of floodplain. A cost analysis of landfill construction with mill tailings indicates that the method would be an economically viable means for increasing the valleywide tailings storage capacity, provided construction with slurried tailings is feasible. A Stage H study is proposed to evaluate slurried tailings as a foundation material, as opposed to hauled tailings used in this present study.

Jan 1, 1981

By W. C. McBee

Technology for the preparation of densifiable sulfur concrete (sulfapave) materials has been devised by the Bureau of Mines. The materials are intended as new construction materials for use in corrosive areas where conventional materials fail. A series of modified sulfur cements were developed, which can be used in combination with dense-graded aggregates to prepare sulfapave materials with excellent corrosion-resistant properties. The materials can be mixed, laid, and compacted into place with conventional hot-mix asphalt pavi.ng equipment. Mixture designs utilizing 5-to 30-pct-modified sulfur cements and dense-graded aggregates gave material properties ranging from rigid to flexible. Laboratory corrosion tests in sulfuric acid showed no material loss or deterioration of physical properties over a 1-year test period in concentrations ranging from 0 to 60 pct at ambient temperatures. Preliminary results on field testing the materials for durability to weathering, corrosion, and traffic have been excellent, with no evidence of failure in the materials.

Jan 1, 1985

By W. L. Dare

This information circular is one of a series the Bureau of Mines plans to publish describing the methods and costs of mining uranium on the Colorado Plateau. The Temple Mountain mining district is unique among the uranium-producing areas on the plateau. This relatively isolated mining district is in Emery County, Utah, on the eastern flank of the San Rafael Swell, about 35 miles southwest of the town of Green River. The district lies just within the eastern escarpment of the San Rafel Reef - a rampart of rugged and tilted sandstone cliffs that encircles the highly eroded core known as the Sinbad Country. The presence of petroleum matter found associated with the ore deposits, the occurrence of uranium in various formations, and the structural deformation caused by collapsed features have aroused a great deal of geologic interest. Mine development on Calyx Flat is distinctive, in that the ore deposits are worked through 36-inch calyx-drill holes.

Jan 1, 1957

By R. D. Groves

Laboratory research has demonstrated that high - grade copper powders can be produced under controlled conditions from cement copper products . The technique should enable small producers to prepare a directly marketable product by means other than smelting and electrolytic purification . A continuous drum- type precipitator was the preferred unit for producing fine - sized particles of cement copper that were further processed by chemical digestion in a copper sulfate solution , by reduction and sintering in a hydrogen atmosphere , and by grinding to a powder . The effects of variables related to all stages of the process were investigated . Treatment of leach solutions from three different sources resulted in copper powders containing 99.2 to 99.8 pct Cu , apparent densities of 1.97 to 2.25 grams per cu cm , good powder flow rates , and a size distribution of 54.9 to 60.1 pct minus 325 - mesh material .

Jan 1, 1964

By W. R. Crane

Recent papers on support of roof and top rock in mines representing present practice in so far as it hits been described by engineers in all of the principal mining countries, cover a relatively aide range of topics. The papers abstracted herein include such subjects as the testing of materials of support, failure and movement of rock above workings, effect of excessive pressures on rock masses, axed the application in mines of timber, metal, concrete, packing, and filling support. It is not within the scope of this paper to present a logical and orderly discussion of the elements of support and their application to conditions influenced by the material worked or the method of mining. Only the essential facts of a paper appear in the abstracts, the idea being to give a fairly clear picture of the behavior of various types of support under brows conditions and to put into concise form important information concerning present practice, modifications of practice, and the trend toward new practice. With such valuable facts from others experience made readily available, it Is hoped that the engineer with particular and often trying problems may obtain suggestions that will be immediately helpful.

Jan 1, 1932

MR. RIGG: Gentlemen, I would like to welcome you all to the symposium this morning. My name is Jack Rigg, and I m a special assistant to Hollis Dole, Assistant Secretary of the Interior for Mineral Resources. Hollis is not in town this morning, and I am here to pinch-hit for him. The first order of business this morning is remarks by the Honorable Russell Train, Under Secretary of the Department of Interior. Mr. Train. MR. TRAIN: Thank you, Mr. Rigg. Lest you think that Hollis Dole is not interested in this symposium, let me just say that fie is flying back from Australia just to be here. He is heading up a United States delegation in Australia meeting on resource problems in the Pacific. And I believe he will be here about noon.

Jan 1, 1970

By Carlton E. Brown

This report contains information on the relation between and precision or reproducibility of counts (light-and dark-field) of the dust in liquid from simultaneous impinger, midget-impinger, electric-precipitator, and filter-paper samples. The impinger was the main sampler used from about 1922 to 1939 by industrial hygienists in the United States for collecting samples of unhygienic dust from the atmospheric environment of workers. The midget-impinger, a small modification of the preceding impinger described in 1937, has been the sampler used most since about 1939. Electric precipitators5/6/ have been used to a limited extent, mainly by the Bureau of Mines in the laboratory, for obtaining results comparable to impinger results. A filter-paper sampler for obtaining results comparable to impinger results has been described by Brown. All these samplers have a high collecting efficiency for particles larger than 1 micron in diameter revealed by the usual light-field counting procedure. However, their collecting efficiencies are quite variable for the smaller particles revealed by the dark-field counting procedure used in this study. Published information on the relation between the results of these samplers is limited and scattered. Summaries of some of this information are given in this report along with some previously unpublished information.

Jan 1, 1949

By David R. Peterson

This report presents a deep ocean mining operational simulation which is capable of describing the response of the bottom collection unit to specified mining ship maneuvers and the corresponding operation of the mining ship maneuvering system. Bathymetry, obstacles, collector and pipe dynamics and ship maneuvering capabilities are included in the simulation. The simulation is capable of evaluating the technical requirements and operating costs for specified mine plans, Results are useful in assessing mine size requirements and provide operating 'cost 'estimates useful as inputs to deep ocean mining economic feasibility assessments, The simulation is used to determine the consequences of obstacles to mining system operations in terms of impact on mine size requirements and reduced production arising from obstacle avoidance maneuvers of a towed (unsteered) collector.

Jan 1, 1979

By J. A. Herdlick

Under authority of the Strategic Materials Act of June 1939, the Federal Bureau of Mines, in cooperation with the Geological Survey, began a broad program of investigation of the strategically important chromite deposits in Sweetgrass, Stillwater, and Carbon Counties, Mont. Extensive occurrences of chromite along the Stillwater Complex in Stillwater County were investigated. The two principal deposits, The Mouat-Sampson and Benbow mines, ultimately were developed and placed in production by the Federal Government. As a part of this general development program, the Carbon County chromite deposits near Red Lodge were examined by Bureau of Mines engineers in 1940, and by the Geological Survey .1-1 1942. The district was examined earlier by Schafer, and the Four Chromes area is mentioned briefly by Westgate. Although the Red Ledge deposits were considered to be of minor importance as compared to those of the Stillwater Complex, several of the ore bodies were adaptable to open-pit mining' methods, and one large deposit on Line Creek Plateau was readily accessible to the Red Lodge-Cooke highway. In 1941, the U. 3. Vanadium Corp. began mining crude lump-chrome ore from the deposit on Line Creek Plateau to supplement national stockpiles, which were being depleted by the rearmament program and the disruption of chrome-ore imports by the European war. Access roads gore constricted to Hellroaring Plateau, and the mining operations were extended to that area. A gravity concentrator with a capacity of 200 tons per day was built and operated at Red Lodge to beneficiate lower-grade ore from the district.

Jan 1, 1948

By W. L. Crentz

Before Korea was partitioned along the 38th parallel following World War II, the coal fields of South Korea, with the possible exception of the Samchok area, were not considered important to the industrial needs or Japan or Korea. Much of the demand for electric power in South Korea was met by hydroelectric installations north of the 38th parallel. Following cessation of hostilities between Japan and the' Allied nations in 1945, hydroelectric power continued to flow into South Korea from the north until 1949, when the North Koreans severed the power lines into South Korea, thereby forcing that section of the country to depend almost entirely upon coal to generate electric power.

Jan 1, 1953