Search Documents

By Robert C. Gabler

Three filter cloth fabrics commonly used in drains for coal waste embankments were tested by the Bureau of Mines for clogging behavior and deterioration under simulated field conditions. The objective was to provide guidelines for the mining industry for the proper selection and use of filter cloths to assure safer embankments at mine waste disposal sites. The filter cloths were tested with three coal waste samples in stand-pipes used to simulate coal mine waste disposal environments. Two of the cloths showed a tendency to become clogged with fines from the wastes. One waste caused clogging by precipitating an iron-silicon compound on the test cloths. No apparent cloth deterioration resulted from exposures to the simulated coal waste environments. (The exposures ranged from 2 to 12 months.) In other tests, exposures to waters in the pH range of 2 to 12 and to reagents used in coal-preparation plants resulted in insignificant or no deterioration, as measured by tensile strength. However, long exposures to sunlight (ranging from 4.6 to 6 months) caused major deterioration in two of the cloths (86-and 98-pct losses in tensile strength) and slight deterioration in the third cloth (9-pct loss in strength).

Jan 1, 1984

By Geo. Adams Roalfe

THIS PAPER is one of a series being pre¬pared for and published by the United States Bureau of Mines describing, methods of mining and crushing and the costs of operation at commercial crushed-stone plants throughout the country. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators, as well as to the industry as a whole. On the other hand, operating, costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. Acknowledgments The author wishes to acknowledge the [ ]

Jan 1, 1932

By M. R. Yenchek

The Bureau of Mines conducted research to determine the relationship between cur-rent load and temperature rises in coal mine trailing cables. Six low-voltage, unshielded, portable power cables were continuously and intermittently loaded with direct current of various magnitudes. Temperature rises within and on the cables were measured with thermocouples, and the data were recorded with a computer. Thermal time constants were calculated, which fixed the periods of the duty-cycle tests. Relationships between average temperature at the conductor-insulation interface and current load were established. The steady-state and intermittent currents that produce a 90° C average conductor-insulation temperature were then determined. Comparisons with Insulated Cable Engineers Association (ICE A) steady-state ratings revealed that 10 to 25 pct more current than recommended ICEA ampacities is required to reach rated insulation temperature. Examination of the maximum intermittent temperatures attained showed that autoignition of coal dust and burn injuries to personnel handling the cable would not be concerns if the temperature at the conductor-insulation interface averaged 90° C.

Jan 1, 1988

By S. P. Kinney

The efficient operation of a blast furnace is primarily dependent upon efficient contact between the descending stream of solid materials and the ascending stream of gas. The United States Bureau of dines is conducting a program of research dealing with the interior of the present-day furnace. The work is being carried oat by.(1) observations on commercial furnaces end (2) experiments in the laboratory. Through the courtesy of the officials of the Illinois Steel Co. it was possible to make a detailed investigation of the interior of the shaft of Number.4 furnace at the company's South Works, South Chicago, Ill. The experimental work is to be reported in a U. S. Bureau of Mines bulletin which will include the results of several thousand observations on the interior of the shaft of this furnace. Such of the data as are presented later in this paper constitute only a brief summary.

Jan 1, 1929

By Michael Rieber

Rail cars are referred to as "yellow-balled" when they are sufficiently old or damaged to preclude their efficient operation on long-haul or main line routes. For most coal carrying railroads, their alternative value is salvage. This, however, does not necessarily preclude their effective use, on a limited basis, by small mines located near existing trackage. Because of age, the sizes of these hopper and gondola cars ace currently 50 and 70 tons rather than the 100 tons commonly built at the present time. As a gathering system, yellow-ball rail could provide an alternative, particularly in Kentucky, western Pennsylvania and west Virginia, to coal trucks, conveyor belts and pneumatic pipelines [4, p.17], belts and pneumatic pipelines. Rail service of this type provides a limited alternative to track abondonment, a possible financial return to a railbank [3], a direct contribution to service demand on main lines, and a means by which many small eastern coal mines could retain or regain competitive viability [4]. In terms of energy efficiency, compared to trucking coal, the total direct energy impact (fuel) of yellow-ball rail can be expected to range from 280-990 Btu/ton-mile while that for trucks ranges from 1850-3120 Btu/ton-mile [2].

Jan 1, 1977

By C. W. Davis

Two general schemes have been used for the determination of gold and silver in material containing considerable quantities of copper ; one is known as the " all fire " method , and the other as the , " combination " , or " wet and dry" method . The all fire crucible method , using an excess charge of litharge , has been found satisfactory when the copper content of an ore is under 6 per cent , ( Loevy , J. , Zur Edelmetallbestimmung in hochprozentigen Kupfererzen : Chem. Ztg . Jarhrg . 35 , 1911 , p . 278 ) , or where the precious metal value is so great that a small sample can be used . In the latter case , silica is added until the copper ratio is sufficiently low . If there is more than 6 per cent of copper in an ore , the lead button obtained from a crucible fusion will require repeated scorification before . it can be cupelled successfully . Rescorification is not only tedious , but also causes a slag loss of precious metals . In combination methods , the copper is dissolved , and the gold and silver in the residue . is determined by fire assay Although some combination methods have given satisfactory results for gold and silver , they are not applicable when an estimation of the platinum metals is required . Since substances containing platinum are frequently high in copper , a study of methods which might be used for the estimation of small quantities of gold , silver , and the platinum metals in such material was considered worth while . The estimation of platinum in ores by fire assay methods has been described in Technical Paper 270 of the bureau; ( Davis , C.W. , The detection and estimation of platinum in ores : U. S. Bureau of Mines Tech . Paper 270 , 1921. ) the present paper , which is supplementary to that report , deals chiefly with the application of combination methods , taking them up to the point where the fire assay is to be applied .

Mar 1, 1921

By C. J. Walker

The ever-increasing use off natural underground formations for storing natural gas has focused attention on the behavior of such storage formations under varying operating conditions. The need for a means of evaluating in¬dividual wells and groups of wells has become manifest. It is essential that industry and others be able to determine the rates of flow that can be ex¬pected from a given well or group of wells under different conditions and to ascertain whether certain wells are deteriorating. Such questions need more exact answers now than ever before because of the vital role underground gas storage plays in the industrial and domestic consumption of natural gas. The Bureau of Mines--in cooperation with the American Gas Association--has main¬tained an active interest in gas-well testing because of the implications of such test procedures on the consumption and efficient production of natural gas. A basis for testing gas wells was provided by the back-pressure method of Rawlins and Schellhardt (12).4/ They showed that for normal gas wells there is a consistent relationship between rates of delivery of gas and corresponding pressures when the formation pressures are used as the basis of interpretation, The equation for this relationship is as follows: Q = C (Pf2 - Ps2)n where; Q = rate of flow, generally expressed in cubic feet per 24 hours. C = a coefficient.

Jan 1, 1960

By C. P. Mangelsdorf

When the finely bedded shale frequently encountered over coal seams experiences a separation, the material below the separation must behave like a beam or plate in that it must resist both bending and shear. Be-cause of the weakness in interlaminar shear inherent in such strata, shear deflections that are usually ignored in isotropic beam theory may account for a significant part of the total roof sag. Similarly, when a roof truss is installed in such a roof the upward displacement reducing the sag will have components due to shear as well as bending. Questions asked by mine operators about the installation of roof trusses frequently deal with optimum position, slope, and initial tension of the inclined chords. This Bureau of Mines report examines the effects of those chord parameters on the strain energy of both shear and bending and offers optimum values that will minimize the total strain energy of the immediate roof. Design charts are provided, several design examples are included, and the results are compared with current practice. The effects of in situ stresses are investigated and are shown to be equivalent to an additional load on the beam.

Jan 1, 1988

By H. F. Feldmann

This Bureau of Mines report presents a method for the computer solution of the equilibrium compositions of any complex, multiphase, chemical system for which appropriate thermodynamic data are available. The method describes in detail the computation of systems in which solid or liquid species can form by heterogeneous chemical reactions where these species do not occur in any equilibrium equations. Also described are the calculation of phases formed by condensation (pure or solutions) and the inclusion of other system restrictions such as electroneutrality. The method is being used to compute the equilibrium composition of mixtures of an electrically conductive plasma and a liquid slag phase arising from the high-temperature combustion of coal for magnetohydrodynamic power generation. These mixtures can contain up to 65 species including gases, liquids, free electrons, and ions.

Jan 1, 1969

By D. Harrington

For several years, or from about 1932 to 1935, inclusive, the coal industry of the United States had an excellent record as to coal-mine explosions. In 1937 and in 1938 to date there has been a definite increase in the number of explosions attended by considerable loss of life and property damage. In most of these explosions one important underlying and contributing cause has been lack of sufficient (or at least efficient) ventilation to properly dilute and remove explosive gas from the mine. This increase in explosions indicates that. the lesson taught through bitter experience, many times in the not far-distant past, of the need for good ventilation is frequently being overlooked, partly because the relatively good experience of the industry in the past several years has made many mining people forgetful. Moreover mining practices are rapidly changing, and in some instances the changes are being made with little if any regard for safety. It appears, therefore, that a review of some ventilation principles and practices should be of value in preventing further disasters; this paper has been prepared with that object in mind. In coal mining the need for thorough ventilation of all underground working places is recognized by both mining practice and law; such ventilation is generally obtained by the use of fans that circulate a quantity of air much in excess of the quantity of coal produced, by weight as well as by volume. For example, in a relatively small mine producing 1,000 tons of coal per day and circulating 100,000 cubic feet of air, which is by no means abnormal, 2,000,000 pounds of coal and approximately 10,900,000 pounds of air would be moved out of the mine every 24 hours. Because of the need for adequate dilution and removal of methane issuing or likely to issue from mine strata and for removal of the carbon dioxide formed by coal and timber oxidation up-to-date coal mines usually provide an air volume which if adequately coursed not only removes these gases but also the gaseous products of the detonation of explosives (which may include carbon monoxide, hydrogen sulphide, nitrogen oxides, carbon dioxide, and nitrogen) and the carbon

Jan 1, 1938

By W. M. Dressel

The objective of the research reported in this publication of the Federal Bureau of Mines was to devise a mineral dressing procedure that would concentrate zinc silicate minerals from certain deposits in southwestern Missouri. The best flotation results were obtained by batch laboratory flotation using sulfidizing agents and ethoxylated cocoamine. The flotation concentrate contained 70 percent of the zinc at a grade of 47.8 percent. Gravity concentration tests showed that 55 percent of the zinc could be recovered at a grade of 48.3 percent.

Jan 1, 1961

By J. W. Paul

A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and discusses regulations and practices which have resulted in a low-frequency rates from falls of roof and coal in a few representative mines, takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of Western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, gross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat, and the block system are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some goad may accrue to many other bituminous mines which have similar natural conditions.

Jan 1, 1933

By John W. Frey

Although there are certain general uniform provisions in the laws ... of the several Provinces of Canada the differences are so great that it is considered advisable to present digests of separate mining laws rather than a digest of Canadian mining law as an entity . This analysis , accordingly , has been divided as follows : Nova Scotia , New Brunswick , Quebec , Ontario , British Columbia , and a group of Provinces under Dominion Law .

Sep 1, 1930

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/ lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By E. J. HOFFMAN, J. c. W. FRAZER

The apparatus and methods described in the following pages were devised and used by the writers in connection with certain investiga- tions of the technologic branch of the United States Geological Sur- vey, especially those bearing on the improvement of furnace condi- tions and on efficiency in the use of fuel. The Bureau of Mines, which has charge of such analyses and tests of fuels as were formerly made by the technologic branch of the Sur- vey, is using the same apparatus and methods in connection with similar investigations that are being carried on at the testing plant of the bureau at Pittsburg, Pa. The furnace conditions prevailing both in small plants and in large industrial establishments in this country are frequently far from satisfactory. If such conditions are to be improved, they must be more thoroughly understood, and means must be found to insure complete combustion of the fuel, and yet to permit operation with such an excess of air as will result in the greatest efficiency. In this work the services of the chemist are indispensable. A very important problem is the determination of the small percentage of unburned combustible matter that escapes from the furnace in the flue gases. Under ordinary circumstances so little as 0.1 per cent of unburned combustible matter in a furnace gas is equivalent to about 1 per cent of the fuel used; and for the determination of such small percentages of gas more accurate and refined methods are required than have ordinarily been available heretofore. It is the purpose of this paper to describe some apparatus and methods which have proved satisfactory to those engaged in the chemical work of the investigations mentioned. While these methods and apparatus have been designed more particularly with regard to analysis of furnace gases, their use is by no means limited to that purpose. The reader will readily see their applicability to other uses in which the sampling and analysis of gases are involved.

Jan 1, 1911

By A. Iannacchione

Major Hazard Risk Assessment (MHRA)1 is used to help prevent major hazards, e.g., fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, etc., from injuring miners. The structured process associated with MHRA helps to characterize the major hazards and evaluate engineering, management and work process factors that impact how a mine mitigates its highest risk. The National Institute for Occupational Safety and Health (NIOSH) studied the application of this technique to US mining conditions through a field-oriented pilot project. Risk assessment teams used in the pilot project were primarily composed of mining company personnel. Ten case studies were performed over a wide cross-section of mines. These mines were representative of the important mining commodities in the US minerals industry, i.e. coal, metal, non-metal, and aggregate. Also, the sizes of the mines ranged from small to large and were located across the country. The ten case studies demonstrate that most US mines have the capability to successfully implement an MHRA and that the MHRA methodology produced additional prevention controls and recovery measures to lessen the risk associated with a select population of major mining hazards. The basic ingredient for a successful MHRA is the desire to become more proactive in dealing with the risks associated with events that can cause multiple fatalities. A successful outcome is marked by a thorough examination of existing prevention controls and recovery measures. When pressed to consider more controls to further mitigate the risk, a well-staffed risk assessment team was able to identify additional controls. For these mining operations, it was important to add additional controls, even if they were not required by existing mining regulations, to lower the risks associated with the major hazards under consideration. If a mining operation is not willing to commit its best people to an MHRA or will not provide them with sufficient time to see the process through to its conclusion, the MHRA output may prove to be useless. Additionally, if a mining operation is not prepared to discuss its major hazards in an open and honest fashion and to present the findings of the risk assessment in a written report, the MHRA output will be unclear, and attempts to monitor or audit important controls may not be possible. A MHRA is most effective when the mining operation possesses 1) a proper understanding of its hazards, 2) experience with informal and basic-formal risk assessment techniques, 3) proper facilities, machinery and equipment, 4) suitable systems and procedures that represent industry Best Practice, 5) appropriate organizational support with adequate staff, communications and training, 6) a formal and thorough plan for emergency response, and 7) a safety risk management approach that is promoted and supported at all levels of the organization.

Jan 1, 2008

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations, of which this is the seventh. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in , this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations of those holes are shown on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of .1 minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By Steven A. Fechner

In 1991 and 1992, the Bureau of Mines completed chromium, platinum-group metals (PGM), and tin investigations, and started indium, manganese, titanium, and vanadium investigations in Alaska. These studies were done as part of the Site Specific Minerals Investigations project. As a result of this work, the Bureau found PGM-bearing composite plutons in the Yentna River area of the Alaska Range, which are chemically similar to composite plutons in other parts of the Alaska Range and to Ural-Alaskan type complexes. Previously unknown chromium and PGM occurrences were found in the western Brooks Range. A compilation report on the Bureau's chromium and PGM investigations in the western Brooks Range was also published. Indium was found in anomalous concentrations at the Lost River tin deposit. Small occurrences of manganese were located, mapped, and sampled in the Wiseman and Chandalar quadrangles, and in the Liberty Falls, Prince William Sound, and Homer areas. Tin occurrences in western Alaska were summarized in three Bureau open file reports. The beaches near Cape Yakataga and Yakutat were evaluated for their titanium potential and a sampling methodology was developed. Vanadium investigations included examining streams in the Wiseman and Eagle areas that contained anomalous vanadium values. In the Eagle area, high vanadium, uranium, and copper values were found in the basal layers of the Road River formation.

Jan 1, 1994

By James S. Browning

The Bureau of Mines conducted laboratory batch and small-scale continuous flotation tests of weathered mica pegmatite ores from Alabama and North Carolina to determine the technical feasibility of recovering commercial-grade mica concentrates. A new anionic-catonic method was developed for recovering mica in the presence of clay slimes. In continuous tests, concentrates containing 98.1 percent mica were obtained from the Alabama pegmatite ore; the North Carolina pegmatite ore concentrates contained 97.2 percent mica. The recoveries were 83.8 and 81.6 percent, respectively.

Jan 1, 1965

By I. L. Nichols

Volatilization of cesium from pollucite ore was investigated as an initial step in the production of purified cesium metal or cesium salts. High recovery of cesium and rubidium as chloride sublimates was accomplished by 2-hour roasts in a tube furnace using charges containing 1 part ore, 2 parts limestone, and 0.23 part calcium chloride. Recoveries of cesium in the sublimate product were 89.1, 92.9, and 95.2 pct, respectively, using 1,100° C and vacuum, 1,250° C with an air sweep, and 1,250° C without an air sweep. Most of the lithium, sodium, and potassium sublimed with the cesium and rubidium, but virtually none of the calcium, aluminum, and silicon in the charges was volatilized.

Jan 1, 1966