Search Documents

By L. L. Oden

The U.S. Bureau of Mines and the Department of Energy (DOE), through its contractor EG&G Idaho Inc., are collaborating on a multiyear research project to evaluate the applicability of three-phase, electric arc furnace melting technology to vitrify materials simulating low-level radioactive and mixed wastes buried or stored at the Idaho National Engineering Laboratory and other DOE sites. The melter is a sealed, 1-t (1.1-st), three-phase, 800-kV?A electric arc melting furnace with 10.2-cm-(4-in?) diameter graphite electrodes, water-cooled roof and sidewalls, and four water-cooled feed tubes. A water-cooled copper fixture provides for continuous tapping of slag. An instrumented air pollution control system (APCS) with access ports for analysis and a feeder based on screw conveyors and a bucket elevator are dedicated to the facility. Test data are provided by an arc furnace analyzer and by sensors indicating feed rate; slag temperature; and temperature, pressure, and velocity in the APCS. These data are received by a data logger, digitized, and transmitted to a personal computer for storage and display. This unique waste treatment facility is available for public and private use on a cost-sharing basis.

Jan 1, 2010

By A. C. Fieldner, S. H. Katz

"Introduction.Recent experiments (Fieldner, A.C., Katz, S.H., Kinney, S.P., and Longfellow, E.S., Poisonous gas from carbon tetrachloride fire extinguishers, Jour. Franklin Institute, October, 1920, pp. 543-565), by the Bureau of Mines have shown that carbon tetrachloride extinguisher liquids when applied to fires produce small quantities of irritating and poisonous gases which may be dangerous in very closely confined spaces where conditions are such that the user can not escape without breathing the fumes. The results of the experiments have been confirmed in an independent investigation by the Underwriters Laboratories (Nuckalls, A.H., Corrosive action and products formed when carbon tetrachloride extinguisher liquids are applied to fires, Nat. Fire Protection Assoc. Quarterly, vol. 14, January, 1921, pp. 221-236) who conducted similar experiments for the purpose of determining the corrosive action of these fumes on metals. Both investigations showed that carbon tetrachloride vapor, hydrochloric acid gas, and phosgene were produced in addition to the ordinary products of combustion, such as smoke, carbon monoxide and carbon dioxide. The Bureau of Mines' tests were made by applying a one-quart extinguisher to a wood fire of excelsior in a gas-tight room of 1000 cubic foot capacity. The glass and metal construction of this chamber limited the experimental fire to very small dimensions. It was, therefore, deemed desirable to make a test on a larger scale in the entry of the Bureau's experimental mine in order to similate more nearly the practical use of carbon tetrachloride and other types of extinguishers in mines.Description of extinguishers.Two series of tests were made under identical conditions on different days. Commercial carbon tetrachloride extinguishers were used in the first series of tests and ""foamite firefoam"" extinguishers in the second series of tests."

Jun 1, 1921

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars arc characteristically of the 'fire door" type that is frequently encountered on outside exit doors of many public, and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes arc added to the face equipment machinery for which they arty required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. I. Judy (our consultant), etc:

Jan 1, 1974

By R. E. Perry

To develop new or improved flotation methods for beneficiating low-grade red iron ores, the Bureau made many bench scale and continuous anionic flotation tests on ferruginous sandstones and calcareous iron ores from the north-eastern part of the Birmingham, Ala., iron district. The ores contained about 21 to 36 percent iron, a to 11 percent lime, and 22 to 64 percent silica. Production of iron concentrates containing 48 to 52 percent iron was technically feasible in batch tests, and the iron recoveries ranged from 85 to 92 percent. In continuous tests 49 to 51 percent iron products were obtained with 80 to 90 percent recovery.

Jan 1, 1962

By Albert Mendelsohn

This paper, describing the mining practice at the Champion mine of the Copper Range Copper Mining Co., is one of a series of papers on mining methods and costs being prepared by the United States Bureau of Mines. Mining practice at the Champion mine has undergone considerable change during the last four years. Previous to that time the mine was worked by the horizontal out-and-fill method, the stopes starting near the shafts and advancing away from them (fig. 2). The floor pillars were mined by the inclined cut-and-fill method, working en the retreat or toward the shafts (fig. 1). At present the mine is being developed to .tope entirely on the retreat by a sublevel inclined cut-and-fill method.

Jan 1, 1931

By J. E. Chilton

The U.S. Bureau of Mines has developed an intrinsically safe carbon monoxide (CO) monitoring system for mines by coupling a fiber-optic data telemetry (FODT) system with a prototype electro-chemical CO monitor. The CO monitoring system can be used in a coal mine as one component of an early fire warning system. This system may be used in belt haulage entries when the entries are used for supplying ventilation air to working places. The FODT accepts a 0.1-to 1.1-V analog signal from the monitor and converts it to pulses (0 to 5 V) at frequencies from 1.1 to 11 kHz that drive a light-emitting diode (LED). An electrically nonconducting fiber-optic cable carries the LED signal to a remote receiver. The receiver analyzes the incoming light signal and displays the measured CO concentration in parts per million. This report discusses the performance of the FODT system and characteristics of the CO monitor such as response times, linearity, and temperature and pressure effects.

Jan 1, 2010

1. A total of 14,413 mining operations reported employment to the Mine Safety and Health Administration (MSHA). Nearly half (48.9%) were sand and gravel operations, followed by stone (28.5%), coal (14.7%), nonmetal (5.7%), and metal mines (2.1%). 2. Mine operators reported 240,000 full-time equivalent workers1 (down 3.9% from 1999). Independent contractors reported 42,000 full-time equivalent workers working on mine property (up 8.6% from 1999). Coal operators accounted for 26.8% of reported employee hours, followed by stone operators (25.9%) and sand and gravel operators (12.1%). 3. Eighty-four (84) work-related mine fatalities occurred in 2000 compared to 90 the year before. •The mine fatality rate was 29.8 per 100,000 full-time equivalent workers compared to a fatality rate of4.6 per 100,000 employees for all private industry. •Thirty-one percent (31%) of the fatalities occurred in underground work areas, which account for only17% of total employment. •Although the largest number of fatalities (28) occurred among miners who work for coal operators, coal contractor employees had the highest fatality rate (61.1 per 100,000 full-time equivalent workers). 4.There were 10,839 nonfatal lost-time injuries reported to MSHA, occurring at a rate of 3.8 injuries per 100full-time equivalent workers, and resulting in a total of 417,918 lost workdays.2 •Among all employees,3 the highest injury rate occurred among coal operator employees (5.6 nonfatal injuries per 100 full-time equivalent workers). •The highest percentage (34.7%) of nonfatal lost-time injuries were due to handling materials (e.g., over-exertion in lifting, pulling, or pushing objects), which also accounted for the greatest percentage of lost workdays (29.3%). •Among the most frequently occurring injuries, the most severe (as measured by the median number of days lost) were associated with accidents involving falls of ground, the use of powered haulage, and slips or falls. •The most frequently reported part of the body injured was the back (22.9% of all injuries). Back injuries accounted for the highest percentage of lost workdays (21.6%). 5.Seven hundred sixty-seven (767) cases of occupational illness were reported to MSHA. •The most frequently reported illness was repetitive trauma, resulting in joint, tendon, or muscle inflammation or irritation (37.3%). •There were 155 (20.2%) illnesses reported as hearing loss. The majority (68.4%) of hearing loss cases occurred among surface workers. •Coal workers' pneumoconiosis accounted for 14.5% of reported illnesses.

May 15, 2002

By L. C. IlsLey

Cooperation between the United States Bureau of Mines and the Safety in Mines Research Board of Great Britain, continuous since 1924, has made possible this and other papers on safety subjects. Grateful acknowledgment is made to representatives of the Safety in Mines Research Board of the Mines Department for their assistance in arranging visits to several mine-safety stations, and to F. H. Wynne, Deputy Chief Inspector of Mines, Great Britain, for arranging visits to mines in Great Britain, Belgium, France, and Germany. During the summer of 1927 the writer had the privilege of visiting the mine-safety testing stations in Great Britain, Belgium, Germany, and France, in the order named. All of these countries have large coal mines, many of which are rated as gassy. Therefore, when the installation of electrical equipment is contemplated, each of these countries is confronted with the same safety problem as in the United States - the development of electrical equipment that will not ignite gassy mine atmospheres, should such atmospheres through neglect or accident surround the equipment. The means used by those countries in safeguarding gassy mines should therefore be of general interest to safety engineers in American coal mines, and it is proposed to give a brief survey for each of the four countries mentioned. The first of these surveys will cover conditions in Great Britain.

Jan 1, 1929

By Roy E. Peterson

The Bureau of Mines conducted an investigation to produce metallized pellets from domestic iron ore superconcentrates using lignite and subbituminous coal as reductants. Feed materials for the metallizing process consisted of commercially indurated iron oxide pellets and green pellets prepared from upgraded domestic concentrates with graphite or limestone as internal additives. Durability of the green pellets during metallization was investigated in tests conducted in a 7-inch-ID rotating drum furnace. Test results indicated that the major cause of pellet disintegration with the concentrates used was the tumbling action during reduction rather than forces generated within the pellets. In larger scale tests made in a 34-inch-ID by 35-foot-long kiln, the previously indurated pellets were metallized with lignite at 1,030° C with little disintegration. A 96-percent level of metallization was obtained in pellets having an average compressive strength of 420 lb. In subsequent, similar tests using green pellets containing graphite or limestone, pellet disintegration was more severe, with 10 to 40 percent of the feed being lost as dust. The surviving pellets had metallizations ranging from 88.3 to 94.4 percent and compressive strengths ranging from 60 to 68 lb.

Jan 1, 1976

By B. D. Hanson

An interactive computer program has been developed by the Bureau of Mines which enables the user to identify the effect of cutting system changes on relative dust generation for longwall shearer drums. The program simultaneously evaluates machine and coal seam parameters, and those parameters which the user can control. The user can change one or more of these parameters at a time to determine their effect on relative dust generation, cutting forces, and/or cost. The program is written in the BASIC programming language. A complete program listing is included along with user instructions and sample outputs. This program is a more comprehensive version of the relative dustiness index (REDI) program described in Bureau Report of Investigations 8979.

Jan 1, 1988

By D. J. Parker

The ease of ignition and violence of explosion of Utah coal dusts, together with the large volumes of methane given off in some of the mines of the State, made it imperative to abandon obsolete equipment and obviously hazardous practices for up-to-date equipment and safer methods of mining if reasonable progress wore to be attained in fire and explosion prevention. Although much can still be done to improve safety conditions in Utah coal mines, considerable progress has been made in the past 10 years. The fundamentals of such progress include increased use of permissible electrical equipment in gassy mines, closed lights, rock-dusting, more liberal use of water at the face, butter ventilation, permissible explosives fired electrically both within and without the mine, partial inhibition of blasting while the shift is in the mine, 100-percent first-aid training, increased supervision and inspection, and mass safety meetings.

Jan 1, 1935

By Aner W. Erickson

"Preliminary examination of tungsten deposits on the Mountain View property near Hyder, Alaska, was made by Neal M. Muir, an engineer of the Bureau of Mines daring the summer of 1942. Fifteen samples were cut, rough esti¬mates of ore reserves were made, and it was proposed to extend the drift on scheelite-bearing vein 300 feet in a northwesterly direction.From May 22 to October 24, 1944, an exploratory project was conducted on the property by the Bureau. In the course of this work, the camp buildings were rehabilitated; the dam, hydraulic line, and machinery were repaired; 226 feet of drift was driven; 80 groove samples aggregating 3.9 tons in weight were cut; a 6,000-foot surface and underground traverse was run; and the area was mapped in detail.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is doe Neal W. Muir, project engineer, and Robert S. Sanford, acting chief, Alaska Division, Mining Branch, for their supervision of the field work and revision of the report.Acknowledgment is also made to Silbak Premier, Ltd., for rendering valuable assistance in the repair of equipment and for extending various courtesies to Bureau of Mines personnel during the conduct of this project.The Mountain View property is located at latitude 55° 59' north, and longitude 130° 03' west in the Salmon River mining district of southeastern Alaska, about 5 miles in a northwesterly direction from the town of Hyder, which lies at the head of Portland Canal, as shown in figures 1 and 2. Vein outcrops and surface workings are at an elevation of 950 feet and occupy the west flank of a low ridge between Skookum and Fish Creeks, as shown in figure 3. The portal of the long adit exposing the vein at depth is on Skookum Creek about 550 feet north of the confluence of Skookum and Fish Creeks.Access to the property is over a 4-foot wide trail built and maintained by the United States Forest Service. This trail is suitable for pack animals and is adequate for transportation of supplies and material for exploratory work. During the periods of camp construction and past exploratory operations a 4,000-foot, single-cable, aerial tramway, now in disrepair, served for transportation of materials and all machinery from the Salmon River Highway to the property. The cost of such hauling was high, amounting to $12 a ton. Topography is suitable for construction of a ""cat road"" 2 miles in length, connecting the property with the Salmon River Highway. It is estimated that such a road could be built for $5,000 a mile, and supplies, machinery, and concentrates could be haled over it at a cost of less than $2.50 a ton."

Sep 1, 1946

By R. E. Peterson

A reduction roasting/magnetic separation/flotation process for beneficiating oxidized taconite from the western Mesabi iron range in Minnesota was evaluated in a Bureau of Mines research program to insure an adequate supply of raw materials for future ironmaking and steelmaking needs. The research was performed on a sample containing 35.4 pct iron and representing a deposit of approximately 2 billion tons of raw materials. An average of 1,419 lb of oxidized taconite and 37 lb of lignite reluctant per hour were fed to a 35 -foot rotary kiln in which the iron oxides were converted to artificial magnetite. The kiln was heated with pulverized lignite and natural gas. Most of the dust collected from the kiln exhaust gas was pelletized and recycled to the kiln. Magnetic separation and cationic flotation of the roasted material in a 900-lb/hr pilot plant produced a concentrate analyzing 67.9 pct iron and 4.9 pct silica and containing 69.2 pct of the iron in the kiln feed.

Jan 1, 1981

By J. E. Chilton

Underground miners may be exposed to hazardous quantities of toxic gases, such as carbon monoxide (CO), generated from mine fires or explosions. Every underground miner is required to carry a filter self-rescuer (FSR), which when operated will remove CO from the miner's breathing air. In addition, every underground miner must have a self-contained self-rescuer (SCSR) near the worksite that will supply breathing oxygen. In many situations, miners do not know when to don either rescuer since they do not know if there is a fire in the mine, nor do they carry instrumentation necessary for the detection of the toxic, colorless, and odorless fire product CO. If each miner carried a personal CO alarm, which would respond to high concentrations of CO, the miner would then be alerted when to don either the FSR or SCSR and exit the mine. A prototype personal miner's CO alarm called PEMCOAL was developed by the U.S. Bureau of Mines. The PEMCOAL unit is small enough to be carried on a miner's belt, has a flash lamp visual alarm, requires no calibration for use, and uses a chemical sensor that changes color by reaction with trace quantities of CO. The chemical sensor was tested at concentrations of CO from 10 to 1,000 ppm, at temperatures from 5° to 40° C, and with several potential mine gas interferents. The PEMCOAL alarm times were sufficiently fast to warn miners before they are exposed to hazardous quantities of CO.

Jan 1, 1989

By Elaine T. Cullen

Underground mining, like many high-risk industries, is facing a crisis in the near future. This industry has traditionally relied on a master-apprentice relationship to train new workers, but experienced miners are retiring in large numbers, leaving few "masters" to properly train their replacements. With a recent resurgence in mining, many new miners are entering the workforce each day. The rise in the number of inexperienced workers has implications for worker safety in an industry in which one mistake can blow up the entire workplace. The explosion in the Darby Mine in May 2006 that killed five miners illustrates what can happen in hazardous environments such as underground mines. The Health Communications Team at the National Institute for Occupational Safety and Health Spokane Research Laboratory was asked to address this problem by developing new training and safety awareness materials to promote safe flame cutting and welding practices. This article describes how occupational ethnographic techniques provided insights needed for "new product development." The result of this work was a national initiative to raise awareness and to protect underground coal miners from the dangers of flame cutting and welding in an environment filled with solid fuel and methane (natural gas). Although this project was initially designed for the mining industry, the approach and lessons learned are applicable to any high-risk industry and should be of interest to other social marketing or occupational safety and health professionals.

Jan 1, 2009

By M. Carrales

This Bureau of Mines publication presents short-range projections of domestic liquid hydrocarbon production through 1980. Appraisal of future crude oil production was made by evaluating the relationship between primary and enhanced oil recovery and the total crude oil producing trends in each of the oil-producing areas of the United States. Future natural gas liquid production was generally estimated by projecting historical production. Estimates of production were prepared for each of the oil producing areas and summarized for the Petroleum Administration for Defense (PAD) districts and total United States. From 1975 to 1980, crude oil production for the conterminous United States is expected to decline from 7.8 to 6.4 million barrels of oil per day (BOPD), and it is expected to increase from 8.0 to 8.2 million BOPD for the total United States. However, these estimates do not include additional production expected from the Elk Hills field in California and the Yates field in Texas. If included, 1980 production for the conterminous United States would be 6.7 million BOPD and 8.4 million BOPD for the total United States.

Jan 1, 1977

By Byron M. Bird

"The prevailing practice of washing unsized coal, 1/2-inch and finer, to 1/8-inch and finer, on a table is subject to certain limitations which are commonly overlooked. In some instances good results are obtained by this method, but often the opposite is true and the efficiency of the washing operation is low. Although the separation taking place on a concentrating table is not fully understood, the actual distribution of particles of various sizes and specific gravities was determined a number of years ago by ore-dressing investigators. Hence this paper consists of an analysis of an old problem by new methods. The experimental data on which the discussion is based were obtained in the course of coal-washing investigations conducted by the U. S. Bureau of Mines at the Northwest Experiment Station in cooperation with the University of Washington and with certain coal operator: of that State.Experimental WorkThe general method of study has been to take a large number of zonal products from the table, and separate them according to specific gravity and size into their component parts. The table used is one of the standard commercial sizes with a diagonal deck. The coal to be washed is split into representative portions, which are stored in separate bins. One portion is used for ""timing as"" the table; the products are collected continuously in the same turned to the feed bin, and thus a closed circuit is completed. When the despite conditions on the table are obtained, coal is fed from one of the re. After the table is operating smoothly the entire product is minute; such a sample is sufficiently large to represent accurately the work of the table and at the same time to minimize the effect of beginning at the end next to the head motion, separate samples are made for each foot along the edge of the deck."

Jun 1, 1926

By W. H. Ode

Because trade increased among various nations after World War II, the Coal Committee of the Economic Commission for Europe established a Classification Working Party in 1949 to develop an International system for classifying coal. Although national classification systems existed, they had been developed in accordance with characteristics of domestic coals without reference to coals of other countries. Terms for describing similar or identical coals differed in each nation. This caused confusion in evaluating coals shipped in international trade and also hampered exchange of technical information on problems of coal utilization. Experts4/ participating in the classification project early in their work agreed that two systems should be formulated, one for the higher rank coals or so-called "hard" coals in European terminology and the other one for the lower rank coals, the latter designated mainly as brown coals and lignites in the various countries. Rank refers to the degree of metamorphism (progressive alteration) in the natural coalification series from lignite and brown coal to anthracite. The system for classification of hard coals was published late in 1956 as a document of the United Nations.5/ Results of a study for applying this system to American coals were published in 1958.6/

Jan 1, 1960

By Richard L. Unger

The Crewstation Analysis Programs (CAP) is a package of computer programs that can be used to analyze some human engineering aspects of crewstation design (such as visibility and illumination) that have particular significance in underground mining. It was developed under the U. S. Bureau of Mines (USBM) Health, Safety and Mining Technology program at the Pittsburgh Research Center, Pittsburgh, PA. This manual describes the steps necessary to collect data in the laboratory to develop luminaire profiles for the CAP illumination analysis. It also describes how the CAP Illumination Model calculates illumination. 1.1 How CAP Calculates Illumination 1.1.1 Background -CAP currently includes assessments of visibility and illumination in the surrounding work area. The advantage of using computers for these types of analyses is that many design iterations can be tested quickly and efficiently to learn the effects of changes. This reduces the need for expensive testing using physical mockups. Another advantage is that design ideas can be tested in situations where it would not normally be possible. For instance, the effects of modifications to a lighting system or canopy design on visibility could be tested while the machine remains in service.

Jan 1, 1994

By K. C. Dean

During the investigation of the occurrence of manganese deposits in western United States, the Bureau of Mines collected 2-ton samples from three oxide manganese ores in the Columbia and Elberta Mining Districts, Tooelo and Juab Counties, Utah. To determine the amenability of these ores to standard ore-dressing methods: of concentration, extensive laboratory tests were made. The Wildcat property, one of those sampled, is 7 miles east of Fairfield, Tooele County, Utah. The ore is described as a replacement deposit and occurs along fracture and bedding planes of shale and limestone. Experimental work was done on a sample taken from a stockpile at the mouth of the shaft. The Wildcat manganese ore is intermediate in grade (25.7 percent manganese) and contains clay as the principal gangue constituent. A high-grade product was obtained with high recovery of Manganese by simple washing.

Jan 1, 1949