Search Documents

By Elizabeth A. Johnson

The vaporization thermodynamics of the aluminum-silicon carbides Al4SiC4 and Al8SiC7 were studied by the Bureau of Mines over the temperature range of approximately 1,500 to 1,700 K. Vapor pressures were measured by a Knudsen effusion-mass spectrometry technique in which powdered samples were effused from graphite crucibles through small orifices. For each compound, a total of six orifice diameters was tested to verify equilibrium within the cell. Aluminum, mass number 27, was the only vapor species detected over the range 4 to 200 amu. Experimental results are based on the following equations for incongruent decomposition: A14SiC4(cr) - 4A1(g) + SiC(a,hex) + 3C(gr); Al8SiC7(cr) - 8A1(g) + SiC(a,hex) + 6C(gr). The observed vapor pressure-temperature relationships determined with a cell orifice area of 2.0 x 10-3 cm2 for Al4SiC4 and 1.81 x 10-3 cm2 for A18SiC7 are the following: Log P - (-18,682/T) + 12.476, for Al4SiC4 (1,550 to 1,643 K) and Log P = (-19,308/T) + 12.421, for Al8SiC7 (1,526 to 1,784 K), with P in pascals and T in kelvins. Third-law analysis of the data provided the following heats of formation: A14SiC4 ?H at 298.15 K - -50.0 kcal/mol and A18SiC7 ?H at 298.15 K - -92.1 kcal/mol.

Jan 1, 2011

By Frank G. Horino

This report describes an instrument designed by the Bureau of Mines for quantitatively identifying texture of rock surfaces produced by grinding or extremely rough surfaces beyond the range of commercial surface measuring instruments. The transducer for the instrument is a linear variable differential transformer that converts mechanical motion caused by surface roughness, waviness, and lay to an electrical output. The electrical output is recorded graphically as an X-Y plot of the line traversed on the rock surface. Details of the synthesized device and its calibration are given. The sensitivity of the unit is 2 percent of the scale setting of the amplifier. The horizontal scale is adaptable from ¼ inch to 15 inches of specimen length with a sensitivity of 0.01 inch if a 10 to 1 magnification is used and 0.1 inch if a 1 to 1 magnification is used.

Jan 1, 1968

By John A. Davis, John Gross

Six tests were made by the Alaska Station of the Bureau of Mines on a sample of black sand delivered to the station by Messrs. James, Eagan & Griffen from Fairbanks Creek, Fairbanks mining district, Territory of Alaska, to devise a method of recovering the gold content. More than 90 per cent of this black sand consisted of magnetite and garnet which can be separated magnetically. The Station has no equipment for magnetic separation other than an electromagnet similar to the one used by Day and Richards, (Day, D.T., and Richards, R.H., Investigations of Black Sands from Placer Mines, U. S. Geol. Survey, Bull. 285, 1906, pp. 150-163), which can only be used satisfactorily on small samples. To treat the entire lot of black sand with this machine would have been impracticable. Therefore only a small part of the sand was so treated, the rest being divided into five lots in order to obtain comparative results from other methods of treatment.

Aug 1, 1920

By Roy L. Wilfong, LeRoy R. Furlong, Louis P. Domingues

The bulk and apparent densities , particle size , and surface area of ceria powders derived from the ammonium sulfate , carbonate , nitrate , oxalate , and sulfate salts and heated at 950 ° to 1,500 ° C for 1 to 24 hours were studied . The bulk and apparent densities and particle size generally increased , and surface area decreased with increase in temperature and time of heating ; surface area was more sensitive to changes in temperature and time than the other properties studied . These properties of the ceria powders had a marked dependence on temperature and a lesser dependence on duration of heating at a given temperature ; and the source of oxide and thermal treatment cannot be considered optional in the preparation of refractory powders by thermal decomposition . The ammonium sulfate and sulfate salts heated at 950 ° and 1,200 ° C produced oxide powders with the lowest bulk density , the smallest particle size , and the highest surface area . The highest apparent densities were achieved for oxides resulting from the carbonate and the sulfate but the carbonate - derived material was considerably coarser . The surface areas of ceria powders derived from cerium salts decrease in the order of sulfate , ammonium sulfate , nitrate , oxalate , and carbonate . The observation of these physical properties are useful in predicting the sintering behavior of various oxide powders .

Jan 1, 1964

By Michael G. Zabetakis, Glenn H. Damon, Joseph A. Herickes

The flammability and explosibility of unsymmetrical dimethylhydrazine ( UDMH ) were investigated by the Federal Bureau of Mines to evaluate hazards associated with commercial application of this material as a missile fuel . This program included the following determinations : 1. Temperature limits of flammability in air at one atmosphere pressure ; 2. limits of flammability at selected elevated temperatures and pressures ; 3. 4 . 5. spontaneous ignition temperature in air at one atmosphere and at 200 pressure per square inch gage ( p.s.i.g. ) initial pressure ; spontaneous decomposition temperatures in nitrogen at one atmosphere and at 200 p.s.i.g .; shock sensitivity over a temperature range from about ( ca. ) 25 ° to 50 ° C .; 6. shock sensitivity of reference propellants ( hydrazine , nitromethane , methyl acetylene , etc. ) ; 7 . shock sensitivity of UDMH plus small amounts of selected metal catalysts . Part of the corresponding data was obtained for a mixture of unsymmetrical - dimethylhydrazine and diethylenetriamine ( U - DETA) .

Jul 1, 1960

By C. E. Coleman, Joseph D. Davis

During some distillation experiments conducted by the Bureau of Mines in cooperation with the Trent Process Corporation it was observed that amalgams of heavy petroleum oils and finely pulverized coal tended to produce a denser coke than that obtainable from the coal when retorted alone . Even anthracite coal when retorted with oil yielded a coke . This led the writers to believe that by mixing a lowrank coal ( sub-bituminous or even lignite ) - with asphaltic oil and retorting it, a coke suitable for domestic fuel could be made . Thus there was contemplated the production of domestic coke and the utilization of a low- grade oil in one operation . - In order to decide on the practicability of this process , it was necessary to know the value of products obtainable by such a method , as compared with those obtained by separate distillation . A laboratory method was therefore devised , and while it was realized that no small - scale testing apparatus for destructive distillation gives results that are directly applicable to commercial - scale operations , by keeping distillation conditions uniform for comparative tests , results were obtained valuable for purposes of comparison . The plan was to distill mixtures of coal and oil in a laboratory retort , and then distill the constituents separately under the same conditions . The comparative quantities of products yielded were thus directly obtained , and their quality was determined by analysis . The following are the main points investigated : ( 1 ) Quantity and quality of coke ; ( 2 ) Quantity of oils boiling below 221 °C . ( gasoline stock) and oils boiling at 221 to 300° C . ( kerosene stock) ; and ( 3) Quantity and quality of gases .

Jan 1, 1922

The Bureau of Mines equipped a longwall shearer with a water-jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 190 psi, and with water-jet-assisted cutting pressures ranging from 1,000 to 6,000 psi. At water pressures of 3,000 psi and higher, dust concentrations were reduced by as much as 85 pct via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1986

By R. V. Ramani, R. A. Jankowski, R. Bhaskar

"The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.IntroductionA number of studies have been performed since the early 1950s on the behavior of dust in mine air (Bradshaw and Godbert, 1954; Dawes and Slack, 1954; Bradshaw et al., 1954; Hall, 1955-56; Reinhardt, 1971; Ford, 1971; Courtney et al., 1982). While the experimental data available from these studies are indeed useful in understanding dust cloud behavior in a specific situation, no generalized conclusions can be drawn because of the lack of data on parameters such as flow velocity, size distribution of the source dust, and particle density. These change from mine to mine or even within the same mine. The present study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground' mine airways (National Academy of Sciences, 1980). The characteristics studied encompassed airborne concentrations and floor depositions over the entire size range as well as the respirable size range. The experimental results in this paper are intended to complement a mathematical model developed to predict ambient concentration and deposition of airborne dust in mine airways (Bhaskar and Ramani, 1986)."

Aug 31, 1989

By Glenn C. Reed

"Preliminary examination of the Glass Buttes mercury deposits, Lake County, Oregon, was made in August 1945 at the request of W. S. Lazier, present lessee of the deposit.Most of the prospect openings in the area were inspected. The more significant workings were sampled and napped in detail. This report presents the data obtained from the investigation to date.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. noon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. P. S. Dean, assistant director.Special acknowledgment is due to S. H. Lorain, chief, Albany Division, Mining Branch and to S. R. Zimmerley, chief, Salt Lake City, Utah, Metallurgical Division, for analyses of the ores.The presence of quicksilver in the Glass Buttes district has been known since about 1930. The area immediately north of Middle Butte has been superficially prospected by numerous test pits, trenches, shafts, and short adits, which revealed a number of opalized zones. Many of these opalized zones contain weak to strong concentrations of cinnabar. The area has not boon explored thoroughly; no mercury has been produced from any of its deposits.A block of 48 full-size claims has been located to cover a large part of the area in sections 34 and 3, Tps. 23 and 24 S.,R. 23 E.,W.M. These claims, held by, location are owned by H. S. Miller, lumberman of Bend, Ore. W. S. Lazier, 10N. W. 20th Avenue, Portland, Ore., currently controls the property under,a nominal leasing agreement. J. W. McDaniel, 44 Lake Place, Bend, Ore., has done much of the underground and surface exploration on the property.The Glass Buttes district is an area of low relief in the Deschutes River drainage system near the northeast corner of Lake County, Ore. (See fig. 1.) The arid climate is marked by extremes of winter and summer temperature. Water for cane use is not available in the immediate area. Well water, however, can be obtained in limited supply on ranch property 5 miles to the south."

Aug 1, 1946

By C. J. H. Brest van Kempen

The objective of this contract was to provide thrust and torque control and visual output torque readout systems to an existing mine roof bolting machine and to test the consistency of torques obtained under actual field conditions. A Lee Norse TD1 roof bolter was modified by adding a simple torque sensing device to the drill rotation mechanism and a pneumatic logic control circuit that measures torque and controls the hydraulic circuit to the rotation motor. The modification controls and indicates the final installation torque of mine roof bolts. A total of over 5,000 mechanical roof bolts were installed in an operating coal mine. The installed torque of these bolts were within an error band (standard deviation) of 8%.

Jan 1, 1978

By D. L. Sawyer

Aqueous C12-02 leaching procedures developed by the Bureau of Mines to produce zinc chloride from zinc sulfide bulk concentrates were effective in extracting 99 pct of the zinc and 97 pet of the silver contained in samples of massive seafloor sulfides from the southern Juan de Fuca Ridge. Zinc sulfide (sphalerite and wurtzite) mineralization comprised 55 and 88 pct of two specimens provided by the U.S. Geological Survey for this study. Minor occurrences of galena, chalcopyrite, and other minerals in the sulfides permitted the recovery of pregnant liquors that were low in metal values other than zinc, which were successfully purified by a two-step cementation procedure using zinc dust.

Jan 1, 1983

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations No. 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the fifth. The data are accompanied by maps showing the location of holes drilled and deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in Volume I. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion of that area.

Jan 1, 1948

By B. J. Scheiner

Extraction of molybdenum from molybdenite ore by an electrolytic oxidation procedure was investigated by the Bureau o f Mines. Various parameters affecting molybdenum extraction, such as salt concentration, temperature, treatment rate, current density, and particle size, were studied. Molybdenum extraction of 95.2 percent was achieved on a laboratory scale from an ore containing 0.35 percent molybdenite. Corresponding power consumption was 24 kwhr per pound of molybdenum extracted with a base consumption of 4.5 pounds of sodium carbonate. Laboratory and pilot plant experiments are in progress on low-grade molybdenum concentrates containing rhenium and copper. Preliminary results indicate that molybdenum extractions in the 90- to 99-percent range and rhenium extractions of 93 to 99 percent can he obtained without appreciable oxidation of associated copper minerals.

Jan 1, 1972

By Richard A. Allwes

The Bureau of Mines conducted an in-mine case study on two consecutive three-entry gate road systems designed in accordance with the stiff-yield pillar design concept. This Bureau study was conducted in order to further develop technology that will improve the health and safety aspects of longwall mining. Support loading and strata activity were monitored to determine the effects of retreat longwall mining on the gate road ground control system. Analyses of pillar stress and roof bolt loading histories revealed that headgate roof support elements ex-perienced cumulative loading throughout the life of the longwall panel. Tailgate pillar loadings had significantly different histories from the loading histories of the headgate pillars. Stress relief occurred in the tailgate pillars following the passage of the longwall face. More-over, the stiff-yield pillar design, with the abutment pillar placed adjacent to the working panel when part of the headgate system, provided effective ground control in that no major roof falls or roof problems were experienced in the headgate or tailgate systems during longwall mining.

Jan 1, 1985

By John S. Dunning

This paper is one of a series describing methods and costs of recovering sand and gravel from deposits in the United States and deals directly with the operations of the Atlas Sand, Gravel and Stone Co. at Farmington, Conn. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local expenditures only and not total production costs. It is recognized that publication of total costs might in some instances cause embarasement to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations may ensue.

Jan 1, 1933

By R. N. Love, L. Goldman

"INTRODUCTION When tannin is present in a boiler water, it causes certain difficulties in many analytical testing procedures because of its colloidal action in interfering with the removal of suspended matter by filtration and also because of the color it imparts to the boiler water.For example, in any test for phosphate in boiler water the first step is to filter out of the sample all sludge and suspended solids. Calcium phosphate in the sludge would give high results if not completely removed. If tannin is present in the sample, the sludge and suspended matter tend to pass through the filter paper so that it is difficult to remove it all. It may even be that tannin makes some of the suspended material in the sample completely nonfilterable. If this is true, it would be necessary to destroy or remove the tannin from the sample before filtering to get complete removal of calcium phosphate from the sample. In addition, if the test used is a colorimetric one, the tannin causes interference by its own color.As the calorimetric phosphate test is so convenient for control purposes and the use of tannin for boiler water treatment has become common, it has become necessary to develop suitable methods for employing the colorimetric phosphate test for boiler waters containing tannin. In this paper three different methods for doing this arc described and studied."

Oct 1, 1946

By R. T. Stull, G. A. Bole

Previous Work . The Bureau of Mines reported a survey of bond clays for graphite crucibles at the American Mining Congress which met at St. Louis in November , 1919 *** . The report contained information in regard to : (a) tests carried on to determine the effect of substituting Canadian and Alabama graphites for Ceylon graphite in varying proportions . The data indicated that Alabama graphite is superior to Canadian graphite and further , that Alabama can be substituted for Ceylon graphite to a large measure without lowering the quality of the ware . These tests were made on No. 70 size brass melting crucibles and were carried out under foundry practice . (b ) Tests were reported in which an attempt was made to modify the nature of Alabama graphite by heat treatment so as to resemble Ceylon graphite . Little advantage from the treatment was reported . With this general information as a basis , the experimental work proceeded along two lines : A study of bond clays for steel -melting crucibles and for brass -melting crucibles . Twenty- one sets of standard-size crucibles were made up of a body containing Ceylon graphite as standard , bonded with 21 bond clays . These tests were carried out under foundry practice as were the former tests . Three domestic clays proved to be superior to the standard Klingenberg clay formerly used in brass -melting practice while in the steel - melting industry , 13 domestic clays gave service superior to Klingenberg clay .

Aug 1, 1923

By Raymond M. Stateham

Calculations based on data obtained from measurements of smoke from coal-fired powerplants predict that infrared imagers will be useful tools for smoke vision. Infrared imagers operating in the 3-to 5-um spectral region have been evaluated for this purpose. A mine opening 110 meters long was filled with smoke from burning coal, and two men, wearing breathing apparatuses, moved through the smoke to serve as targets. The men were detected and identified at 80 meters.

Jan 1, 1976

By M. O. Renwick, Paul Zinner

"INTRODUCTION In September 1943, the Bureau of Mines conducted a limited program of churn drilling on the Winskell property in the Shullsburg area of Lafayette County, Wis. The work was undertaken as part of a general investigation by the Bureau of the zinc-producing area of southwestern Wisconsin at a time when special effort war being made to increase the production of metals necessary for the war program.Drilling described supplemented a previous drilling program conducted by the Vinegar Hill Zinc Co. The results of both programs encouraged subsequent investigation by the Cuba Mining Co. and eventual development of the Andrews mine.ACKNOWLEDGEMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by such project as soon as praticable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the investigative work, and prepares the final report."

Aug 1, 1947

By Paul L. Russell

This property has been examined several times in the last few years , and findings have been reported . In the fall of 1942 , the author supervised sampling both lode and placer deposits . The ore was beneficiated , and the results obtained are incorporated in this report . stia The Morgan Group , which comprises seven unpatented mining claims and the Black Cat placer claims , was purchased by the Manganese Products Corp. from H. D. Hill of Hatch , N. Mex . , and Dr. A. C. White of Hot Springs , N. Mex . Arthur L. McRowe , 876 27th Avenue , San Francisco , is president of the corporation , and David Fewer, 824 Times Building, Long Beach, is treasurer . J. T. Murray is in charge of operations .

Feb 1, 1947