Search Documents

By W. P. Haynes, J. W. Mulvihill, G. B. Taylor, S. Katell

Capital and operating costs have been estimated for separating methane and hydrogen in gas - separating plants designed to produce 90 million scf per day of product gas containing a minimum of 90 percent methane . After a preliminary literature review of various separation techniques , three different processes --moving - bed adsorption using active carbon , oil absorption , and liquefaction -- were chosen for the cost estimates . Three different methane feed gas concentrations , 5 , 20 , and 50 percent ( cases 1 , 2 , and 3 , respectively ) , were chosen as representative methane concentrations for the separation estimates . Capital and operating costs were lowest for the moving - bed adsorption process in all three cases investigated . Operating costs declined from $ 0.24 to $ 0.06 per 1,000 cu ft of product gas , and capital costs declined from $47,490,800 to $7,411,200 as the percentage of methane in the feed gas increased from 5 to 50 percent .

Jan 1, 1964

By Albert W. Deurbrouck

This report describes preparation characteristics of significant coalbeds in Tazewell County , Va . In 1961 Tazewell County produced 933,110 tons of clean coal from six coalbeds ; the Lower Banner , Raven , Jawbone , Upper Seaboard , and Pocahontas No. 3 and No. 5. Samples from all of these beds , except the Lower Banner , were included in this study plus a sample from the Pocahontas No. 4 bed . Of the samples collected , only one would require upgrading to be of metallurgical quality . The coals ranged in rank from high- volatile -A to low- volatile bituminous .

Jan 1, 1963

By D. B. Taliaferro

Information regarding the pores or voids in reservoir rocks is vitally important in the scientific extraction of petroleum from natural underground reservoirs, and petroleum technologists concerned, with subsurface, conditions have devised various methods that give reasonably accurate information as to the porosities of oil and gas-bearing sands.5/ In this, work, several investigators have made use of the experience of the ceramic and other industries. The method of determining the effective porosity of oil sands described in this report falls within the general classification of gas-expansion methods. It was devised and developed at the United States Bureau of Mines Petroleum Experiment Station, Bartlesville, Okla., as a part of the research dealing with fluid and energy relations in reservoirs and improved oil-recovery methods. The apparatus and procedure are well adapted to the requirements of the Bureau, and the following detailed description has been prepared so that others may make use of the information. A tabulation at the end of the report gives the results of several hundred porosity determinations for oil sands in fields of 11 States.

Jan 1, 1937

By D. B. Taliaferro

Information regarding the pores or voids in reservoir rocks is vitally important in the scientific extraction of petroleum from natural underground reservoirs, and petroleum technologists concerned. with subsurface conditions have devised various methods that give reasonably accurate information as to the porosities of oil and gas-bearing sands.5/ In this work, several investigators have made use of the experience of the ceramic and other industries. The method of determining the effective porosity of oil sands described in this report falls within the general classification of gas-expansion methods. It was devised and developed at the United States Bureau of Mines Petroleum Experiment Station, Bartlesville, Okla., as a part of the research dealing with fluid and energy relations in reservoirs and improved oil-recovery methods. The apparatus and procedure are well adapted to the requirements of the Bureau, and the following detailed description has been prepared so that others may make use of the information. A tabulation at the end of the report gives the results of several hundred porosity determinations for oil sands in fields of 11 States.

Jan 1, 1937

By William Cochran

Data on the cost and quantity available were developed for rutile (TiO2), which is potentially recoverable as a byproduct at sand-washing plants in the Southeastern States of Alabama, Georgia, North Carolina, and South Carolina. Baaed on 1969 production data, an estimated 4,300 tons of rutile could be recovered annually from plants that process more than 25,000 tons of sand per year. Rutile prices at which this resource would be available ranged upward from $262 per ton, compared with the current market value of $185 per ton.

Jan 1, 1972

By D. A. Reynolds, J. D. Davis

During early development of the blast furnace, Connellsville coke made entirely from Pittsburgh-bed coal proved to be an excellent fuel. The need for blending coking coals arose as the industry grew and it became necessary to carbonize coals having voking properties inferior to those of Pittsburgh coal Most coals carbonized today in continental Europe and this country are blonded: This practise has improved the quality of coke and permitted the utilization of coals that would yield inferior coke, if carbonized sepa- rately, The depletion of the world's better coking coals, which has been noted by leading coal technologists,2/4/wes accelerated during the recent war and. It is important, therefore, that reserves be evaluated and conserved. In the principal, steel-producing sections of this country, Pocahontas coals have been blended so extensively that the terms "low-volatile coking coal": and. "Pocahontas" have become virtually synonymous. Other low-volatile coals. have been used to manufacture metallurgical coke and will be used more extensively as, the supply of the better known and more accessible Pocahontas coals decreases. Recognizing the need for augmenting the supply of high-rank coking coals, the Bureau of Mines has included both low- and medium-volatile coals in its Survey of the Carbonizing Properties of American Coals, which was started with the cooperation of the American Gas Association in 1929. Twenty coals, 12 of low-volatile and 8 of medium-volatile rank, have been blended with high-volatile A Pittsburgh-bed coal, and five standard low- volatile coals have been blended with various high-volatile coals. Most of the results of carbonization tests of these coals and their blends have been

May 1, 1946

By Thomas V. Falkie, R. Venkataramani

The method of analysis was to test a large model containing potentially significant variables and on the basis of the results obtained, to reduce the model to one containing only the essential significant variables. This stepwise procedure of "scanning" a large proposed model and subsequently condensing the model consisted of two cycles of the same series of computational procedures. Data Preparation A majority of the variables measured were continuous over a specific range of values; for example, the variable "Width Ratio" varied in practice from 0.25 to 1.00. However, "dummy" values were assigned to certain operational variables in order that these varia¬bles would have numerical expression. The following variables were described in this manner. Variable "Dummy" Value x3: Development/Pillaring 0, if pillar extraction was being done 1, if development mining was being done x4: Boxcut/Open Cut 0, if a box cut was being made 1, if an open cut was being made The variables under consideration are represented symbolically as follows: Y: Loading rate (tons per minuts): TONS/MIN x1: Ratio, width of cut/width of cutter: WDRATIO x2: Ratio, height of cut/diameter of cutter: HTRATIO x3: Development or pillaring: D/P

Jan 1, 1972

By Fay B. Dillard

This Bureau of Mines report reviews the disposition of natural gas as delivered to industrial consumers via main line sales. Salient information on main line, or direct, natural gas sales to industrial users is presented by State) standard industrial classification code (SIC) revenue, and type of sales for the years 1968 through 1973.

Jan 1, 1975

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1956 was made under a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 120 samples of aviation gasoline and for 38 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers' 1956 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 17 producers of aviation jet fuels are represented.

Jan 1, 1957

By R. V. Ramani, C. B. Manula, A. Owili-Eger

PART 1 THE INPUT AND OUTPUT DATA AND THE MINE SCHEMATIC SHOWING THE FLOWS FROM COMPUTER SOLUTIONS FOR APPLICATION I

Jan 1, 1975

By Richard O. Kneisley

An empirical method, based on U. S. Bureau of Mines field studies in several Western U.S. coal mines, is presented for sizing gate road yield pillars. Discriminant analysis was used to generate functions separating successful from unsuccessful case studies. These functions relate the pillar width-height and extraction ratios and a pillar development factor to the Coal Mine Roof Rating System (CMRR), and are assumed to establish three criteria that other entry systems, under similar conditions, must satisfy. A program, Pillar Sizer, from user-provided inputs, generates a range of pillar sizes that meets the proposed criteria. Although the analysis is based on a sample consisting primarily of two-entry systems, the derived expressions generate pillar sizes closely agreeing with observed, two-entry and three-entry in situ pillars. It is concluded that the proposed approach should assist mine operators estimate entry system yield pillar dimensions.

Jan 1, 2010

By D. Bienstock

A high-B.t.u, gas can be synthesized by the catalytic methanation of a mixture of 2.5 to 3 parts of hydrogen to 1 part of carbon monoxide, obtained in the gasification of coal, using a steel catalyst followed by Raney nickel in a hot-gas-recycle system. Conversion of 99 percent of the H2+CO yields a fuel gas with a heating value of 983 to 1130 B.t.u. per cubic foot containing 78 to 96 percent methane, no carbon monoxide, and very small amounts of unsaturated hydrocarbons. With the steel catalyst alone, conversions were 85 to 90 percent, giving a fuel gas of 810 to 868 B.t.u, per cubic foot, or 847 to 975 B.t.u. on a C02-free basis. INTRODUCTION In 1948 the U.S, marketed production of natural gas was 5.15 trillion cubic feet; by 1958 it had reached 11.0 trillion cubic feet, a rate of growth of 8 percent annually. 4 5 Although demand is expected to increase less rapidly, by 1966 it may reach 16 trillion cubic feet, based on an estimated 4.7 percent annual increase.6

Jan 1, 1961

By J. A. Cavallaro

This Bureau of Mines report describes the preparation characteristics of 10 coal samples collected from the significant coal-producing mines of Lucas, Mahaska, Marion, Monroe, and Wapello Counties in Iowa, with special emphasis on physical desulfurization. All 10 samples were of high sulfur content as received, ranging from 4.2 to 10.4 percent; the organic sulfur content ranged from 0.8 to 3.8 percent. The pyritic sulfur content of the samples could be appreciably reduced by crushing and washing and provided pyritic sulfur reductions ranging from 36 to 75 percent. Crushing to 3/8-inch top size and removing the sink 1.60 specific gravity material would provide float coal products containing 3.5 to 6.0 percent sulfur. However, these coals could be burned at utility plants utilizing SO2 removal processes with efficiencies ranging from 70 to 88 percent and still be in compliance with the current Federal SO2 emission regulations for stationary sources.

Jan 1, 1973

By N. H. Coates

The Bureau of Mines determined average film coefficients of heat transfer for helium flowing through smooth, water-cooled tubes at Reynolds numbers of 5,000 to 25,000, helium inlet temperatures of 1,600° to 2,600° F, average temperature difference across the helium film of 800° to 1,300° F, and heat flux to 215,000 Btu/(hr)(sq ft). Since helium was the only gas used, the ranges of values for physical properties of the fluid are limited--thermal conductivity from 0.15 to 0.20 Btu/(hr)(sq ft)(O F/ft), viscosity from 0.082 to 0.104 lb/(ft)(hr), and Prandtl number from 0.63 to 0.68. Four equations, three of them dimensionless, correlate these coefficients with other properties of the helium--bulk temperature, film temperature, dimensionless parameters based on temperature, and the ratio of wall temperature to bulk temperature.

Jan 1, 1966

By Kenneth J. Miller

The Federal Bureau of Mines coal-pyrite flotation process has been modi¬fied to produce a concentrated final clean coal slurry underflow that could be dewatered more effectively by filtration or centrifugation. This change was accomplished by redesigning the Bureau's two-stage flotation pilot plant facility and running the second-stage flotation step with undiluted or only partially diluted first stage coal froth concentrate. Results of the pilot plant flotation tests showed that substantial sulfur reduction could be achieved by flotation with undiluted pulp but some dilution is recommended for maximum selectivity. For example, coal-pyrite flotation in slurry of 25 percent solids yielded clean coal products analyzing as low as 0.7 percent pyritic sulfur and froth reject products containing slightly over 3.0 percent pyritic sulfur. In comparison, coal-pyrite flotation with pulp diluted to about 12.5 percent solids yielded clean coal containing as low as 0.4 percent pyritic sulfur and froth reject of 5.6 to 6.7 percent pyritic sulfur. Despite the need for some dilution, it was concluded that excellent coal-¬pyrite flotation selectivity could be achieved without diluting to 6 or 7 per¬cent solids as done in the earlier work. Thus the economics of coal-pyrite flotation would be improved by easing clean coal dewatering problems and by reducing second-stage flotation cell volume requirements.

Jan 1, 1977

By L. C. IlsLey

A list of permissible mine equipment approved by the Bureau of Mines before January 1, 1940, was published in Bureau of Mines Information Circu- lar 71103. Information Circular 71584, published as a supplement thereto, listed equipment approved during the calendar year 1940. The present list contains the information given in those two circulars, as well as approvals issued during the calendar year 1941. It embraces electrically operated air compressors, coal drills, conveyors and loading machines, electrical equipment for mine fans, mining machines and trucks, mine pumps, rock- dust distributors, room hoists, storage-battery gathering and haulage locomotives, storage-battery power trucks and shuttle cars, mine telephones, junction and distribution boxes, electric cap lamps, flame safety lamps, electric hand and trip lamps, electric flood lamps, flashlights, methane detectors, and single- and multiple-shot blasting units. The equipment listed is not approved by the Bureau of Mines until found by inspection and test to comply with minimum standards of safety as outlined in "schedules" prepared upon the basis of many years of ex- perience in dealing with safety problems confronting the coal-mining in- dustry. The use of such equipment in mines that are known to be gassy,. as well as in those that may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept informed as to the many types of machines, devices, and lamps that are available for reducing explosion and other hazards incidental to coal mining.

Apr 1, 1942

By David A. Benjamin

From 1986 to 1989, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 59,600-acre Mexican Mountain Wilderness Study Area (UT-060-054) in order to evaluate its identified mineral resources. The study area is located in Emery County, UT, about 24 miles east of Castle Dale, UT. A review of the geologic and mining literature, and a field examination identified two uranium prospects in the Wilderness Study Area, and three copper prospects nearby. One-hundred ninety-five rock samples were taken.

Jan 1, 1989

By J. W. Miller

From 1889, when the first railroad shipments of coal were made from McDowell County, W. Va., until today, the coals produced from the New River and Pocahontas groups have had a good reputation as premium low-volatile coals. Although there has been a large production from the Pocahontas No. 3 and. Pocahontas No. 4 beds, considerable reserves remain. This Bureau of Mines publication is one of a series appraising the Nation's coking-coal reserves by presenting data on the basis of which the practicability of upgrading marginal deposits to metallurgical standards can be determined. This study of the preparation characteristics of McDowell County coals is the second of the series to be undertaken in West Virginia. The Pocahontas No. 3 and No, 4 beds have not been included because their washing characteristics are well known.

Jan 1, 1954

By Sean Gallagher, William S. Marras, Alan S. Litsky, Deborah Burr

Background. There is currently little information regarding factors associated with specific modes of motion segment failure using a fatigue failure model. Methods. Thirty-six human lumbar motion segments were fatigue tested using spinal compressive and shear loads that simulated lifting a 9 kg weight in three torso flexion angles (0, 22.5, and 45). Twenty-five segments failed via fatigue prior to the 10,000 cycle maximum. These specimens were visually inspected and dissected so that the mode(s) of failure could be determined.Failure modes included endplate fractures (classified into nine varieties), vertebral body fractures, and/or zygapophysial joint disruption. Logistic regression analyses were performed to determine whether certain morphometric variables, amount of motion segment flexion, disk degeneration scores, and/or loading characteristics were associated with the occurrence of specific failure modes. Findings. Results indicated that stellate endplate fractures were associated with increased posterior shear forces (P < 0.05) and less degenerated discs (P < 0.01). Fractures running laterally across the endplate were associated with motion segments having larger volumes (P < 0.01). Endplate depression was more common in smaller specimens (P < 0.01), as well as those experiencing increased posterior shear force (P < 0.05). Zygapophysial joint damage was more likely to occur in a neutral posture (P < 0.01).Interpretation. These results suggest that prediction of failure modes (e.g., specific endplate fracture patterns) may be possible (atleast for older specimens)

By Sean Gallagher, Christopher A. Hamrick, Arnold C. Love

Twelve subjects participated in an investigation of the biomechanical stresses of asymmetric lifting in stooped and kneeling postures. Three factors were manipulated in this study: Posture (stooped or kneeling), height of lift (35 or 70 cm), and weight of lift (15, 20, or 25 kg). Subjects were required to lift or lower a box every 10 seconds for a period of 2 minutes. Electromyography (PIG) of eight trunk muscles was collected during a lift in this period. The PIG data, normalized to maximum extension and flexion exertions in each posture, were input to a biomechanical model and used to predict compression and shear forces at the L, level of the lumbar spine. Results from the EMG-driven biomechanical model indicated that compression was greater when lifting to a higher shelf (p < 0.001), and indicated a significant interaction between posture and the weight of the lifting box (p < 0.01). Peak lateral shear was not significantly affected by any main effects or interactions (p < 0.05). Anterior shear was increased with increasing height of lift (p < 0.001), and also by the posture x weight interaction (p c 0.01). A multivariate analysis of variance (MANOVA) indicated a complex relationship for recruitment of the eight trunk muscles, with the triple interaction being significant (p < 0.001). The results of this investigation will be used to evaluate safe loads for lifting in these restricted postures.