Search Documents

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

3. Application of Proposed Revised Standards 57.11-50 to Mines Surveyed 3.1 Subparagraph (a) 1 "Each mine shall have at least two separate and properly maintained escapeways from each working place to the surface which are so positioned that physical or environmental damage to one will not lessen the effective¬ness of the other, and which meet the requirements of travelways and man hoisting standards These escape¬ways shall reach to within 1000 feet horizontally or 300 feet vertically of each working place " 3. 1. 1 Discussion This section will deal with the 1000 and 300 feet distance requirements, Section 3. 5 will deal with the "environmental damage" provisions. During the course of the mine surveys, it became obvious that one mine's 1000 foot distance was nowhere near equal to another' s --not in the actual distance but in the time required to traverse that distance. This -Ls true for the 300-foot requirement as well. The most obvious example is that one could traverse down a 300-foot raise much faster than climbing up the same distance. The temptation is strong to recommend that the distance requirement be changed to travel times instead. However, this approach would unfortunately lead to a lot of subjective evaluations. Having a time requirement for an entire mine evacuation (Subparagraph 6) is one thing, time requirements and the requisite inspection proce¬dures for each working place are quite another.

Jan 1, 1976

By A. S. Griffiths, J. E. Evans

Noise processing experiments with ELF (3 to 300 Hz) atmospheric noise and signals in the 40 to 80 Hz range are described. The primary purpose of the experiments was to record and analyze wideband ELF noise in order to design the noise processing portion of a receiver which minimizes the required transmitter power. The application of appropriate theory and extensive simulations led to a noise processor which consists of the following functions: (1) a compensating (or whitening) filter, (2) a prenotch filter clipper, (3) notch filters at frequencies of manmade interference (e. g., power lines), (4) a post-notch filter clipper, and (5) a phase-coherent linear matched filter. The nonlinear processing provides considerable gain relative to a linear receiver (i. e. , a receiver consisting only of a matched filter and appropriate whitening filters). It is convenient to measure sys tem performance in terms of an "effective noise level" which is equal to twice the received signal energy divided by the signal to noise ratio at the matched filter output. For example, the highest effective noise levels observed at 45 Hz with the nonlinear processor were about -134, -131 and -137 dB wrt 1 amp/m [Hz] using Saipan, Malta and Norway data, respectively, compared to 1 percent exceedance levels of effective noise for the linear receiver of about -115, 115 and -130 dB wrt 1 amp/m [Hz] respectively.

Jan 1, 1973

By Thomas C. Ruhe

The Bureau of Mines conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) saves energy, reduces oil imports, and reduces mining costs. Low ambient temperatures may cause these recycled oils to become too viscous for proper absorption by ammonium nitrate (AN) prills and result in poor blast performance, safety hazards, and environmental problems. To help quantify and resolve these issues, viscosity, mixing, and performance tests were conducted at various temperatures. Diesel fuels No. 1 and No. 2 were studied separately and in blends with 25,50, and 75% RO. Good quality ANFO mixes (94-6) were produced with dry absorbent prills and blended fuel (No. 1 diesel plus RO) at temperatures as low as -40° F (-40°C) with 75% No. 1125% RO, and at -20°F (-29°C) with 50/50. Diesel fuel No. 2 also made good mixes as low as -30" F (-34" C) with 75% No. 2/25% RO, and at 0° F(-18° C)with 50/50. Reference detonation velocity tests were conducted in 1.4" (3.6 cm) diameter steel pipe at 70°F (21°C) on No. 1 diesel ANFO (94-6), giving an average value of 9722 ft/s (2964 m/s). Comparison tests showed good ANFO performance at low temperatures. Blended fuel ANFO (75% No. 1/25% RO) mixed, loaded, and tested at -40°F (-40°C), produced an average velocity of 9247 Ws (281 8 m/s). A 50/50 blend gave a velocity of 8083 Ws (2464 ds) at -20°F (-29°C). Based on these results, a practical field method has been developed to help evaluate whether a specific oil blend will mix properly with AN at a low ambient temperature. This method will help to promote the safe and reliable use of RO ANFO at low temperatures, with adequate performance.

Jan 1, 2008

By C. C. Shale

A semicommercia1, high-temperature electrostatic precipitator and adjunct equipment are described, and operating characteristics at 1,470° F and 80 psig are presented for both positive and negative polarity. Removal efficiency for negative corona waS about 91 to 96 percent while that for positive corona was only about 75 to 77 percent. Results are compared with those from bench-scale investigations, and equipment limitations are discussed. Theoretical aspects of the precipitation process are related to the operating characteristics.

Jan 1, 1969

By Alfred E. Schwaneke

An improved maximum-bubble-pressure system using the Sugden twin-capillary method for measuring the surface tension and density of molten metals is described. Improvements include (1) internally ground capillary tips, (2) electronic pressure transducers, (3) micrometer adjustment of immersion depth for density measurements, (4) valuing arrangements to allow operation at other than atmospheric pressure, (5) temperature range to 1,100° C, and (6) recorder readout of pressures. Data for surface tension of mercury from 20° to 300° C are given.

Jan 1, 1970

By Irven A. Jacobson

The thermal reactions of l-methylindole were studied in the temperature range of 525° to 627° C in a flow reactor. The major products consisted of 2-methylindole, 3-methylindole, indole, quinoline, hydrogen, and methane. 2-Methylindole is formed from 1-methylindole by an irreversible isomerization reaction. The 2-methylindole isomerizes in a reversible manner to 3-methyl-indole, the equilibrium favoring the 3-methyl isomer. Indole is formed directly from 1-methylindole. Quinoline is formed from l-methylindole, 2-methylindole, and 3-methylindole.

Jan 1, 1971

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX C SCALING RELATIONSHIPS 1. Scaling Law for Fly Ash Crater Formation The scaling law derived for predicting crater diameters at different scales is developed below by considering the equation of motion of individual fly ash particles. It is assumed that the air drag on each particle is characterized by Stokes flow, and at the borehole - passage intersection the air velocity and the fly ash particle velocity are the same. The equations of motion for a fly ash particle are the following, (see Figure C-1).

Jan 1, 1973

By Charles L. Kimbell

In 1990, the aggregate value of world international export trade in mineral commodities was estimated at more than $64 billion in current (1990) dollars, about 8.4% higher than that in 1989, but still 8.7% below the record high set in 1980. Table 8 provides a data series for the estimated value of world export trade in all mineral commodities from 1979 through 1990, as well as a breakdown of this total into fuel and nonfuel commodities. It is noteworthy that for this 1990 edition, trade data for the year of review were available in time for inclusion, whereas in previous editions, the latest available global trade data were for the year prior to the year of review. Hence, as regards trade, this edition of Minerals in the World Economy updates the 1989 edition by 2 years rather than by only 1. For this reason, it is appropriate to note that the 1989 global total value for inter-national export trade in mineral commodities was almost $596 billion, 11.1 % above the revised 1988 level of more than $536 billion, both figures expressed in current dollars for the appropriate year. Despite the considerable increase in the dollar value of mineral commodity exports, their share of total export merchandise trade declined to 19.1 % in 1990 from 19.7% in 1989. At 19.1%, this share was very near the recent year record low of 19.0% reached in 1988. The year 1990 was the fourth in a row in which the total value of world mineral commodity export trade increased.

Jan 1, 1993

By K. O. Bennington

The thermodynamic properites of petalite (Li2A12Si8O20) were determined by the Bureau of Mines. The enthalpy of formation was determined by hydro-fluoric acid solution calorimetry. The values from the elements and from the oxides are ?Hf°298.15 = 2,335.8 ± 3.0 kcal/mole and ?H°295 (from oxides) = -50.60 ± 1.20 kcal/mole. Low-temperature heat capacities were determined by adiabatic calorimetry from 10.69 to 302.11 K. The derived standard entropy is S°298.15 = 111.0 ± 1 cal/deg-mole. Enthalpy increments above 298 K were measured by copper block calorimetry from 298 K to 1,193.6 K. The various experimental data were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of the measurements. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature from the elements and constituent oxides. The Gibbs energy of formation is ?G°f298.15 = 2,203.8 kcal/mole.

Jan 1, 1980

By C. H. Elder, M. C. Irani

Two degasification test boreholes were drilled to depths of 1,238 and 1,212 feet on Bureau of Mines property at Bruceton, Pa., as part of the Bureau's long-range coal degasification program. The holes provided detailed geologic information and geologic sections, which were correlated with regional stratigraphic cross sections prepared by the Pennsylvania Geological Survey. Gas content determinations and coal analyses were made on the Upper Freeport, Middle Kittanning, Clarion, Brookville, and Mercer coalbeds; gas content of the coalbeds ranged from 53 to 165 cubic feet per ton. Formation pressure and gas flow tests were conducted on selected coalbed intervals in borehole 1; formation pressures ranged from 292 to 473 psig. The middle Kittanning coalbed was hydraulically stimulated using very heavy gelled water, but gas production remained low because gel residue and formation water inhibited the flow of gas. Gas contents in the Clarion, Upper Brookville, and Mercer coalbeds were anomalously low owing to the proximity of porous sand- stones which act as reservoirs for gas migrating from coalbeds.

Jan 1, 1977

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

2, Survey of Representative Group of Metal and Non-mental Mines Before proceeding to develop and analyze Emergency Escape System Guidelines, it was necessary to obtain a broad range of information, including both fact and opinion. Although there were many areas to consider, the surveys had three primary goals 1. To determine the current state of underground escapeway planning and execution in American, metal and non-metal mines. 2. To determine, for a wide range of mining conditions, what difficulties can be encountered in complying with present and proposed escapeway regulatory standards. 3. To determine what improvements could be made and what equipment and technology was available to aid in implementing these improvements. To accomplish these goals, three major surveys were undertaken¬ 1. Survey of MESA and State Mining officials, discussed in Section 2. 1. 2. Survey of representative U S metal and non-metal mines, discussed in Section 2. 2. 3. Survey of manufacturers supplying equipment, primarily hoisting, suitable for use in escape systems, the product information which was obtained is discussed in Section 7.

Jan 1, 1976

Reduce respirable dust in coal preparation plants. Approach Survey a representative sample of coal preparation plants to (1) determine the dust problem extent, and (2) evaluate practical dust control techniques. Coal Preparation Plant Survey Results Of the approximately 500 coal preparation plants in the United States, 18 plants in six States were randomly selected for survey. The raw hourly capacities ranged from 250 to 1,250 tons, plant construction dates ranged from 1037 to 1982, and usually 3 to 10 workers were required per shift. Respirable dust concentrations within the plants surveyed ranged from very good (less than 1 mg/m') to very poor (14 mg/m3). No relationship was found between dust concentration and age or capacity of the plant. Six of the plants had long-term respirable dust concentrations between 7 and 14 mg/m' in specific areas; six had concentrations between 2.2 and 6.2 mg/m'. Except fur ventilation, only 4 of the 18 plants used operating dust control devices with mixed effectiveness.

Jan 1, 1989

By A. B. Hooker, L. C. IlsLey

Several ignitions or mine pa, which might have led to explosions, and at least ona mine fire attributed to heated leg wires of electric detonators, have occm.rred. at rn1::.es in which outside shot firing is practiced. Photographs taken at one mine ind.la.ted. that the wires became red hot during firing. These results having been --i·-led. to the .Lttention of the electrical section of the Bureau of the Mines, ignitions the tests and to reportd aid in herein preventing were made future to trouble determine of if this possible kind, the cause of The investigation, which 1• considered preliminary, included tests to determine the conditions tha.t cause gas ignitions from heated. leg wires of electric and. of detonators, copper leg possible wires, remedies The tor samples such of heating, wire used. and in the the relative test were behavior the of reg\llar ironDa. Pont iron and copper leg wires (No, 22 A,W,G.) C\1t from Du. Pont electric detonators.

Aug 1, 1922

By R. Barany

The heats of formation at 298.15° K of calcium tungstate, calcium molybdate, and magnesium molybdate were determined by solution calorimetry. For the heats of formation from the elements, the values obtained were calcium tungstate, -402.4 ± 0.5 kcal/mole, calcium molybdate, -369.5 ± 0.3 kcal/mole, -334.8 ± 0.2 kcal/mole. For the heats of formation from the oxides J the values obtained were calcium tungstate, -49.2 ± 0.4 kcal/mole, calcium molybdate, -39.6 ± 0.1 kcal/mole, and magnesium molybdate, -12.9 [ ] 0.1 kcal/mole.

Jan 1, 1962

By Ernest W. Loya

A method for preparing gravimetric primary standards of helium in the parts per trillion range has been developed by the Bureau of Mines. The standards are used to calibrate a specially modified mass spectrometer used in determining the abundance of helium-3 and helium-4 in geochemical samples and of helium-3 in isotopically purified helium-4. The desired gas standards are prepared in 5-kg metal cylinders filled to 1,800 psia. Relative errors of less than 1 pct have been attained in the parts per trillion range using a successive dilution technique.

Jan 1, 1982

By W. H. Pailes, V. Castranova, D. Lewis, G. Goodman

We performed bronchoscopy with bronchoalveolar lavage (BAL) in 8 control subjects with no exposure to occupational dusts, 8 healthy power plant workers exposed to mixed dusts (primarily fly ash), 1 healthy coal miner and 1 rock driller with acute silicosis. All subjects were non-smoking males. We analyzed lavage effluents for total numbers of alveolar macrophages, lymphocytes and neutrophils and monitored chemiluminescence at rest (REST CL) and after stimulation with 3x10- M phorbol-12-myristate-13-acetate (PMA CL) or 2 mg/ml zymosan (ZYM CL). The data are as follows:

Jan 1, 1988

By Seth C. Schaefer

The Bureau of Mines studied thermodynamic properties of liquid Al-Si alloys with the high-temperature galvanic cell Al(1)//Al+3(AlC13 in NaCl?KCl)//Al-Si alloy(1). Activities of aluminum and silicon (referred to pure liquid metals) show a pronounced negative deviation from Raoult's law in liquid Al-Si alloys containing 0.9 to 35.2 atomic-percent silicon. Activity coefficients and the properties [?Gi, ?GxS ,?H, ?G, ?Gxs , and ?S] have been derived from the experimental data and are summarized in tables and illustrations.

Jan 1, 1974

By T. A. Henrie, D. C. Fleck, D. G. Kesterke

Uranium metal was electrowon from uranium dioxide dissolved in fluoride melts . The UO₂ was fed directly to the cell in a continuous manner . Electrolysis was performed at 1 , 200 ° to 1,300 ° C in electrolytes composed of UF4 , LiF , and BaFa . A single regulus of metal was collected in a confined area of the crucible . Product purity of 99.8 percent was attained . Carbon was the major contaminant . Compartmented cells were studied as a means of confining the oxide feed to the vicinity of the anodes .

Jan 1, 1964

By Launa G. Mallett, Kathleen Kowalski-Trakofler, Robert H. Peters, Charles PH. D. Vaught, Peter Keating, William J. Wiehagen

On-the-job training is a common means of training or retraining workers and the practice may seem simple and straightforward. Doing it effectively however requires more thought and preparation than simply having someone follow an experienced worker around and watch what they're doing. Over the years, various techniques and practices have evolved that pass on the skills and knowledge of a trainer or coach in a manner that leads an inexperienced trainee to really absorb the information being taught. On-the-job training thus becomes less a haphazard show-and-tell and more a real transfer of information. The goal of this document is to describe how to develop or manage an on-the-job training program so that information is passed on from trainer/coach to trainee efficiently and effectively. By efficient is meant the best use of time and resources of all those involved in the training process, and by effective is meant that the trainee truly learns the skills and internalizes the knowledge needed to perform the job well. The first part of the document discusses topics to think about when developing a formal on- the-job training program. A structure based on coaching is suggested. Then a workshop designed to prepare trainers as coaches is described. Workshop materials include an instructor’s guide and trainee workbook. These materials can be used to train coaches and to assist trainees as they go through the learning process. Content related to specific jobs can be added to these materials to create targeted on-the job-training manuals. Structuring a formal on-the-job training program It is likely that some form of on-the-job training (OJT) is being conducted at your workplace. The formality of that training can range from a structured program to an informal “follow Joe around” method. If your program is completely unstructured, it may not be meeting current training needs. Worse, it may perpetuate bad habits and create “trained” employees who are not given the same information or evaluated to the same standards. Wiehagen et al. comment that, “Success in using unplanned OJT is usually dependent on the luck of the draw, that is, whether the informal trainer is competent at the task he or she is teaching, is motivated to teach, can organize the job into logical components, and knows something about good practices in teaching and evaluating” (2002, p. 27). It is only through planning a structured OJT program that consistency can be created and maintained. At the least, all trainees who have successfully completed such a program can be expected to perform at an established level—they will know what they must do to be successful.

Jan 7, 2005

By G. Nuñez, M. A. Pathak, C. F. Stanley

"Holographic interferometry is a non-destructive technique to detect small deformations1 of an object. It is a whole-field technique· with an accuracy of a few microns. An adaptation of holographic interferometry is time-averaged holographic interferometry which is particularly useful in detecting small vibration amplitudes of an object under investigation. Its application to biological tissue is especially difficult due to the combination of (a) the high sensitivity of the technique, and (b) the tendency of these objects to deform excessively, or move during the testing period. (This is also compounded by the changing moisture content of the tissue surface.)Ideally, a pulsed laser and fast-acting thermoplastic film camera could be chosen to overcome these difficulties, but the total equipment cost could exceed $75,000. In this paper we describe our relatively economical method to apply time· averaged holographic interferometry to an excised animal lung, utilizing holographic plates and a mechanically-shuttered continuous-wave Argon laser.EXPERIMENTAL METHODThe schematic of the experimental setup is shown in Fig. 1. The holographic equipment, including the laser, is fixed on a 3 ft x 6 ft x 4 in. honeycomb holographic table. This table is functionally similar to one described by Mark and Horsch2 which can be constructed for about one thousand dollars. The holographic table itself rests on six inner tubes to absorb floor vibrations. All unnecessary vibrations must be reduced to preserve the quality of the holograms. A laser beam from a 0.5-watt continuous-wave Argon laser is split by a circular variable beamsplitter (Newport Corporation Model 50GOOAV.1) into two beams, i.e., an object beam and a reference beam. The object beam is again split into two beams of equal intensity by a 50150 beamsplitter (Newport ·Corporation Model BS.1). These beams are optically filtered and expanded by spatial filters (Newport Corporation Model 910) to cover as much area of the object as possible. Soft biological tissues exhibit low reflectives, resulting in a relatively high reference to object beam ratio of roughly 5 : 1 at the holographic plate."

Jan 1, 1989